Selective spectrophotometric determination of TNT using a dicyclohexylamine-based colorimetric sensor

Because of the extremely heterogeneous distribution of explosives in contaminated soils, on-site colorimetric methods are efficient tools to assess the nature and extent of contamination. To meet the need for rapid and low-cost chemical sensing of explosive traces or residues in soil and post-blast debris, a colorimetric absorption-based sensor for trinitrotoluene (TNT) determination has been developed. The charge-transfer (CT) reagent (dicyclohexylamine, DCHA) is entrapped in a polyvinylchloride (PVC) polymer matrix plasticised with dioctylphtalate (DOP), and moulded into a transparent sensor membrane sliced into test strips capable of sensing TNT showing an absorption maximum at 530 nm when placed in a 1-mm spectrophotometer cell. The sensor gave a linear absorption response to 5-50 mg L⁻¹ TNT solutions in 30% aqueous acetone with limit of detection (LOD): 3 mg L⁻¹. The sensor is only affected by tetryl, but not by RDX, pentaerythritoltetranitrate (PETN), dinitrotoluene (DNT), and picric acid. The proposed method was statistically validated for TNT assay against high performance liquid chromatography (HPLC) using a standard sample of Comp B. The developed sensor was relatively resistant to air and water, was of low-cost and high specificity, gave a rapid and reproducible response, and was suitable for field use of TNT determination in both dry and humid soil and groundwater with a portable colorimeter.     

Selective spectrophotometric determination of TNT in soil and water with dicyclohexylamine extraction

Contaminated land and groundwater remediation in military waste dumping sites often necessitates the use of simple, cost-effective, and rapid tests for detecting trinitrotoluene (TNT) residues in the field along with their dinitro-analogues. A simple, rapid, low-cost, and field-adaptable (on-site) colorimetric method was developed for quantifying TNT in the presence of RDX, PETN, picric acid, 2,4-DNT (dinitrotoluene), dinitrophenol, and dinitroaniline. Most commercialized methods for TNT assay-with the exception of Cold Regions Research and Engineering Laboratory of the U.S. Army (CRREL) method-use proprietary chemicals, and the color stability and intensity are highly dependent on the composition of the organic solution comprised of acetone or methanol. The developed colorimetric method is based on the extraction of TNT from water-acetone solution into an organic solvent mixture of dicyclohexylamine (DCHA)-isobutyl methyl ketone (IBMK) (10:1, v/v), filtration through a filter paper into a stoppered optical cell containing anhydrous sodium sulfate, and measurement of the absorbance of the organic extract at 531 nm after 5 min. The red-violet color of the extract was due to intermolecular charge-transfer (CT) between the electron attracting TNT and electron-donating DCHA, and the molar absorptivity for TNT in final organic solution was (1.16 ± 0.02) × 10⁴ L mol⁻¹ cm⁻¹.The R.S.D. of the slope of calibration line was 0.7%. The LOD of the method in the final organic phase was 0.38 μM TNT, and LOD values expressed on the basis of original soil TNT content were 0.5, 1.3, and 1.5 ppm (μg g⁻¹) for clay, loamy clay, and sandy soils, respectively. Unlike other spectrophotometric methods, the developed assay was basically tolerant to common cations and anions found in soil and water at 100-fold weight ratios, and to soil humic acids. Among a number of compounds that may be encountered in polynitro-explosive storage and waste reclaimation sites such as picric acid, dinitrophenol, 2,4-dinitrotoluene, dinitroaniline, RDX, PETN, and tetryl, only tetryl interfered with the developed TNT assay. Water tolerance and exploitability over a wide pH range were other superiorities over the CRREL method. The CT-complex was relatively stable, as the absorbance of the organic extract was not significantly influenced from the dilution of the water-acetone phase. Aside from the extractive-photometric procedure established for aqueous solutions, a simulated field colorimetric assay for TNT directly applicable to soil was also devised, based on direct color development in a 4:1 (v/v) acetone-dicyclohexylamine organic extract of soil at a liquid-to-solid ratio of 5 mL g⁻¹.     

Measurement and modeling of mean activity coefficients of NaBr and amino acid in (sodium bromide + potassium phosphate + glycine + water) system at T (298.15 and 308.15) K

Electrochemical measurements are done on (water + NaBr + K₃PO₄ + glycine) mixtures at T (298.15 and 308.15) K by using (Na⁺ glass) and (Br⁻ solid-state) ion selective electrodes. The mean ionic activity coefficients of NaBr are determined at five NaBr molalities (0.1, 0.3, 0.5, 0.7, and 1) in the above mixtures. The activity coefficients of glycine are evaluated from mean ionic activity coefficients of sodium bromide. The ratio of mean ionic activity coefficient of NaBr in the (water + NaBr + K₃PO₄ + glycine) mixtures to the mean ionic activity coefficients of NaBr at the same molalities in the (H₂O + NaBr) mixtures are correlated by using a new expression.     

Effect of the polarity of silver nanoparticles induced by ionic liquids on facilitated transport for the separation of propylene/propane mixtures

The effect of ionic liquids on the formation of a partial positive charge on the surface of silver nanoparticle and its subsequent effect on facilitated olefin transport were investigated. Three different ionic liquids of 1-butyl-3-methylimidazolium tetrafluoroborate (BMIM⁺BF₄⁻), 1-butyl-3-methylimidazolium triflate (BMIM⁺Tf⁻), and 1-butyl-3-methylimidazolium nitrate (BMIM⁺NO₃⁻) were employed to control the positive charge density of the surface of silver nanoparticles. The positive charge density of the silver nanoparticles, as characterized by the binding energy of the silver atom, was in the following order: BMIM⁺BF₄⁻/Ag ? BMIM⁺Tf⁻/Ag > BMIM⁺NO₃⁻/Ag. This order was consistent with the tendency of ionic liquids to form free ions. The best separation performance for the propylene/propane mixtures was a mixed gas selectivity of 17 and a permeance of 7 GPU through a composite membrane consisting of BMIM⁺BF₄⁻/Ag. A better separation performance for olefin/paraffin mixtures was observed with a higher positive charge density of the silver nanoparticles. It was therefore concluded that facilitated olefin transport was a direct consequence of the surface positive charge of the silver nanoparticles induced by ionic liquids.     

Vapour pressure and excess Gibbs free energy of binary mixtures of hydrogen sulphide with ethane, propane, and n-butane at temperature of 182.33 K

The vapour pressure of binary mixtures of hydrogen sulphide with ethane, propane, and n-butane was measured at T = 182.33 K covering most of the composition range. The excess Gibbs free energy of these mixtures has been derived from the measurements made. For the equimolar mixtures for (H₂S + C₂H₆), (820.1 ± 2.4) J · mol⁻¹ for (H₂S + C₃H₈), and (818.6 ± 0.9) J · mol⁻¹ for (H₂S + n-C₄H₁₀). The binary mixtures of H₂S with ethane and with propane exhibit azeotropes, but that with n-butane does not.     

Use of the molybdenum-thiocyanate-rhodamine 6G ternary complex for spectrophotometric molybdenum determination without extraction

A modified thiocyanate method without extraction by using rhodamine 6G as a secondary ligand was developed. Molybdenum in 1.0×10⁻² M HCl, after the addition of ascorbic acid, was heated for 10 min in a 90 °C water bath for reduction. Suitable amounts of glycerine, Triton X-100, rhodamine 6G solutions and 2+1 (v/v) 9 M H₂SO₄+3 M KHSO₄ were added in this order. This solution was allowed to cool to room temperature and the absorbance at 570 nm was measured against a reagent blank 45 min after the addition of thiocyanate solution and the second aliquot of Triton X-100 solution. The complex was stable for at least 4 h, the order of reagent addition was important, and thiocyanate should be in large excess. Beer’s law was obeyed over the range 0.9×10⁻⁶ to 1.1×10⁻⁵ M Mo with the molar absorptivity being 1.1×10⁵ l mol⁻¹ cm⁻¹. The R.S.D. for the determination of 0.7 mg Mo l⁻¹ was 1.83% (n=8). Possible interferences of various cations and anions on molybdenum determination were studied. The proposed method was applied to the determination of molybdenum in a dental alloy, Wiron 99.     

Surfactant-sensitized malachite green method for trace determination of orthophosphate in aqueous solution

A surfactant-sensitized spectrophotometric method for determination of trace orthophosphate has been developed using anion surfactant (Ultrawet 60 L) with molybdate and malachite green in low acidic medium (pH_T 1.0). The method detection limit (3 × standard deviation of blank, n = 10) was 8 nM and the calibration curve was linear over a range of 10-400 nM (r² = 0.997). The molar absorptivity was 1.26 × 10⁵ L mol⁻¹ cm⁻¹ at 600 nm with the background correction at 530 nm. The precision of method was 3.4% at 50 nM and 2.4% at 100 nM orthophosphate (n = 10). The hydrolysis of eight organic phosphorus and polyphosphate compounds was less than 2% of the total phosphorus present (5-10 μM). This method showed less arsenate interference than previous methods, with only 3% even in the presence of orthophosphate in the samples. No interference of silicate up to 40 μM was observed. Background anions (in an order of SO₄²⁻ > NO₃⁻ > Cl⁻) have greater effects than cations (Ca²⁺ > Mg²⁺ > Na⁺) on the reagent blank and the molar absorptivity of the color product.     

Study of diffusion-controlled and activation-diffusion-controlled electron-transfer processes from quenching measurements

The diffusion-controlled rate constants, k_d, of various quenching reactions, [Ru(L)₃]^2+∗ (L = bpy, phen and 4,7-(CH₃)₂phen) + [Fe(CN)₆]³⁻, were measured through fluorescence measurements. From them, the effective values of viscosity coefficients for several methanol + water mixtures were calculated. These coefficients were checked through calculations of the rate constants of the reaction [IrCl₆]²⁻ + [Ru(bpy)₃]^2+∗, which were also obtained by fluorescence quenching measurements. The agreement between the two sets of data (experimental and predicted) is excellent. Besides, the trends of association, k_d, and dissociation, k_−d, rate constants for 2+/3−, 2+/2− and 2+/2+ reactions in methanol-water mixtures are discussed. The use of effective diffusion coefficients for estimating k_d and k_−d allowed us to obtain the intrinsic electron transfer rate constant, k_et, for the activation-diffusion-controlled process between [Ru(bpy)₃]^2+∗ and [Co(NH₃)₅Cl]²⁺ complexes from the observed (quenching) rate constant. The influence of methanol-water mixtures on k_et was rationalized by using the Marcus electron-transfer treatment.     

Vapor-liquid equilibria of ternary systems with 1-ethyl-3-methylimidazolium ethyl sulfate using headspace gas chromatography

Vapor-liquid equilibria (VLE) for two binary systems 1-propanol + water and methyl acetate + methanol, and the ternary mixtures with the ionic liquid 1-ethyl-3-methylimidazolium ethyl sulfate [EMIM]⁺[EtSO₄]⁻ as entrainer were measured by headspace gas chromatography. From the experimental VLE data, the influence of the ionic liquid on the separation factors was investigated. The experimental results for the ternary systems show that [EMIM]⁺[EtSO₄]⁻ has a great influence on the separation factors of the systems investigated. Furthermore, the experimental separation factors were compared with the predicted ones of other ionic liquids and conventional selective solvents using modified UNIFAC (Dortmund).     

Synthesis,electrochemistry and in situ spectroelectrochemistry of a new Co(III) thio Schiff-base complex with N,N′-bis(2-aminothiophenol)-1,4-bis(carboxylidene phenoxy)butane

A new cobalt Schiff-base complex, [Co(L)(OH)(H₂O)] (where L = [N,N′-bis(2-aminothiophenol)-1,4-bis(carboxylidene phenoxy)butane), was synthesized and its electrochemical and spectroelectochemical properties were investigated using cyclic voltammetry (CV), differential pulse voltammetry (DPV) and thin-layer spectro-electrochemistry in solutions of dimethyl sulfoxide (DMSO) and dichloromethane (CH₂Cl₂). The [Co(L)(OH)(H₂O)] complex displays two well-defined reversible reduction processes with the corresponding anodic waves. The half-wave potentials of the first and second reduction processes were displayed at E_1/2 = 0.08 V and E_1/2 = −1.21 V (scan rate: 0.100 Vs⁻¹) in DMSO, and E_1/2 = −0.124 V and E_1/2 = −1.32 V (scan rate: 0.100 Vs⁻¹) in CH₂Cl₂. The potentials of the reduction processes in DMSO are shifted toward negative potentials (0.220–0.112 V) compared to those in CH₂Cl₂. The electrochemical results are assigned to two one-electron reduction processes; [Co(III)L] + ⁻e → [Co(II)L]⁻ and [Co(II)L]⁻ + ⁻e → [Co(I)L]²⁻. The six-coordination of the complex remains unchanged during the reduction processes and the electron transfer processes were not followed by a chemical reaction upon scan reversal. It was also seen that [Co(L)(OH)(H₂O)] was reduced at a more positive potential than the corresponding salen analogs. The shift and reversibility are apparently related to the high degree of electron delocalization of the [Co(L)(OH)(H₂O)] complex, having a N₂O₂S₂ donor set and two additional benzene units. Additionally, in situ spectroelectrochemical measurements support Co(III)/Co(II) and Co(II)/Co(I) reversible reduction processes with the observation of the corresponding spectral changes with the applied potentials E_app = −0.40 and −1.60 V. Application of the spectroelectrochemical results allowed the determination ofE_1/2 and n (the number of electrons) from the spectra of the fully oxidized and reduced species in one unified experiment as well. The results obtained by this method are in agreement with those by the CV and DPV methods.     

Basic study on the determination of total boron by conversion to tetrafluoroborate ion (BF4) followed by ion chromatography

The basic study on the determination of tetrafluoroborate ion (BF₄⁻) by ion chromatography, and total boron by conversion of boric acid to BF₄⁻ followed by ion chromatography of BF₄⁻ has been carried out. The results of thermodynamic calculations for the system of boric acid (H₃BO₃)-F⁻-H⁺ showed that the mole fraction of BF₄⁻ was higher than 99% at pH lower than 3.5 and 4.5 when the total free fluoride concentration (2[H₂F₂] + 2[HF₂⁻] + [HF] + [F⁻]) was as high as 0.1 and 1.0 M, respectively. The fraction of BF₄⁻ increased with increasing total free fluoride concentration. BF₄⁻ fraction values were higher than 99% at pH 0.75 and at total free fluoride concentration of 0.05 M or higher. BF₄⁻ was hardly formed at pH > 7 even when the total free fluoride concentration was as high as 1.0 M. According to the experimental results, the fraction of BF₄⁻ at pH 0.7-0.8 was 51.2, 95.6 and 96.7% when the total fluoride concentration (2[H₂F₂] + 2[HF₂⁻] + [HF] + [F⁻] + 3[BF₃OH⁻] + 4[BF₄⁻]) was 0.2, 1.0 and 3.3 M, respectively. The formation reaction of BF₄⁻ from boric acid reached an equilibrium state within 20 min regardless of reaction temperature, in the range of 20-50 °C, when the total boron and total fluoride concentrations were 66.7 mM and 1.0 M, respectively. Although BF₄⁻ was formed only under acidic conditions, BF₄⁻, once formed, was very stable under alkaline conditions at least for several hours. We have concluded that BF₄⁻ could be analyzed by ion chromatography using sodium hydroxide solution as an eluent because BF₄⁻ was stable under chromatographic conditions. BF₄⁻ solution prepared from boric acid could be used as a standard solution in the ion chromatographic analysis of BF₄⁻ instead of the sodium tetrafluoroborate (NaBF₄) reagent available commercially, if a discrepancy of about 4-5% was allowed.     

Thermal properties of N-alkyl-N-methylpyrrolidinium and N-butylpyridinium fluorometallates and physicochemical properties of their melts

A series of N-alkyl-N-methylpyrrolidinium (RMPyr⁺, where R = E: ethyl, B: butyl, and H: hexyl) and N-butylpyridinium (BPy⁺) salts based on the fluorocomplex anions, BF₄⁻, PF₆⁻, SbF₆⁻, NbF₆⁻, TaF₆⁻, and WF₇⁻, have been synthesized and their thermal behavior has been investigated. The melting points of the RMPyr⁺ salts are above room temperature with the trend; BMPyrAF₆ < HMPyrAF₆ < EMPyrAF₆ for the hexafluorocomplex salts. Some of the salts containing BMPyr⁺ and HMPyr⁺ exhibit phase transitions in the solid states. Similar melting points of BPy⁺ salts of PF₆⁻, SbF₆⁻, NbF₆⁻, TaF₆⁻, and WF₇⁻ are observed at around 350 K. Ionic conductivity and viscosity for BMPyrNbF₆ (3.0 mS cm⁻¹ and 164 cP at 328 K) are similar to those for BMPyrTaF₆ (3.0 mS cm⁻¹ and 165 cP at 328 K), resulting from the similarity of the anions in size. The activation energies of ionic conductivity for the NbF₆⁻ and TaF₆⁻ salts are 18 and 20 kJ mol⁻¹, and those for viscosity are 23 and 25 kJ mol⁻¹, respectively calculated by Arrhenius equation in the temperature range between 328 and 348 K. Electrochemical windows of BMPyrNbF₆, BMPyrTaF₆, and BMPyrWF₇ are about 4.0, 5.0 and 3.1 V, respectively.     

Ionic liquids monolithic columns for protein separation in capillary electrochromatography

A series of ionic liquids (ILs) monolithic capillary columns based on 1-vinyl-3-octylimidazolium (ViOcIm⁺) were prepared by two approaches (“one-pot” approach and “anion-exchange” approach). The effects of different anions (bromide, Br⁻; tetrafluoroborate, BF₄⁻; hexafluorophosphate, PF₆⁻; and bis-trifluoromethanesulfonylimide, NTf₂⁻) on chromatography performance of all the resulting columns were investigated systematically under capillary electrochromatography (CEC) mode. The results indicated that all these columns could generate a stable reversed electroosmotic flow (EOF) over a wide pH range from 2.0 to 12.0. For the columns prepared by “one-pot” approach, the EOF decreased in the order of ViOcIm⁺Br⁻ > ViOcIm⁺BF₄⁻ > ViOcIm⁺PF₆⁻ > ViOcIm⁺NTf₂⁻ under the same CEC conditions; the ViOcIm⁺Br⁻ based column exhibited highest column efficiencies for the test small molecules; the ViOcIm⁺NTf₂⁻ based column possessed the strongest retention for aromatic hydrocarbons; and baseline separation of four standard proteins was achieved on ViOcIm⁺NTf₂⁻ based column corresponding to the highest column efficiency of 479 000 N m⁻¹ for cytochrome c (Cyt c). These results indicated that the property of ILs based columns could be tuned successfully by changing anions, which gave these columns potential to separate both small molecules and macro biomolecules.     

Development of the diffusive gradient in thin films technique for the measurement of labile mercury species in waters

The diffusive gradients in thin films (DGT) technique, utilizing resin gel with ion-exchange resin Duolite GT73 and new ion-exchange resin Ambersep GT74, was investigated for the accumulation of four mercury species (Hg²⁺, CH₃Hg⁺, C₂H₅Hg⁺, C₆H₅Hg⁺). The diffusion coefficients of mercury species in agarose gel calculated on the basis of Fick’s Law were mercury species-specific. The diffusion coefficients of Hg²⁺ and CH₃Hg⁺ at 25 °C (9.07 ± 0.23 × 10⁻⁶ cm² s⁻¹ and 9.06 ± 0.30 × 10⁻⁶ cm² s⁻¹, respectively) were very similar, but the diffusion coefficients of C₂H₅Hg⁺ (6.87 ± 0.23 × 10⁻⁶ cm² s⁻¹) and C₆H₅Hg⁺ (3.86 ± 0.19 × 10⁻⁶ cm² s⁻¹) were significantly lower. Influence of experimental conditions (pH, selected cations, chlorides and humic substance) on mercury species accumulation by DGT was studied. The DGT technique was applied to river water spiked with mercury species.     

Catalytic-adsorptive stripping voltammetric determination of ultra-trace iridium(III). Application to fresh- and sea-water

An extremely sensitive stripping voltammetric procedure for ultra-trace determination of iridium(III) is reported. The method is based on the interfacial accumulation of the iridium(III)-CTAB complex onto the glassy carbon electrode, followed by the catalytic reduction of the adsorbed complex in the presence of bromate. 0.3 mol L⁻¹ acetate buffer pH 4.7 + 6.9 × 10⁻² mol L⁻¹ NaBrO₃ + 2.7 × 10⁻⁵ mol L⁻¹ cetyltrimethylammonium bromide (CTAB) + 0.2 mol L⁻¹ KCl was employed as the supporting electrolyte.The analytical procedure was verified by the analysis of the standard reference materials: Sea Water BCR-CRM 403 and Fresh Water NIST-SRM 1643d.The accuracy, expressed as relative error e%, was satisfactory, being lower than 6%, while precision as repeatability, expressed as relative standard deviation s_r%, was generally lower than 5%. The limit of detection was of the order of 2-3 ng L⁻¹.Once set up on the standard reference materials, the analytical procedure was transferred and applied to superficial water sampled in proximity to superhighway and in the Po river mouth area.     

Selection of entrainers in the 1-hexene/n-hexane system with a limited solubility

Vapor-liquid equilibria (VLE) have been measured for five 1-hexene/n-hexane/ionic liquid systems and 1-hexene/n-hexane/NMP (N-methyl-2-pyrrolidone) system with a headspace-gas chromatography (HSGC) apparatus at 333.15 K. The ionic liquids investigated were 1,3-dimethylimidazolium tetrafluoroborate [C₂MIM]⁺[BF₄]⁻, 1-butyl-3-methylimidazolium tetrafluoroborate [C₄MIM]⁺[BF₄]⁻, 1-methyl-3-octylimidazolium tetrafluoroborate [C₈MIM]⁺[BF₄]⁻, 1,3-dimethylimidazolium dicyanamide [C₂MIM]⁺[N(CN)₂]⁻ and 1-octylquinolinium bis(trifluoromethylsulfonyl)amide [C₈Chin]⁺[BTA]⁻. It was found that at low feeding concentration of 1-hexene and n-hexane, the separation ability of ionic liquids is in the order of [C₂MIM]⁺[BF₄]⁻ > [C₄MIM]⁺[BF₄]⁻ ≈ [C₂MIM]⁺[N(CN)₂]⁻ > [C₈MIM]⁺[BF₄]⁻ > [C₈Chin]⁺[BTA]⁻, which is consistent with the priori prediction of the COSMO-RS (conductor-like screening model for real solvents) model. But at high feeding concentration, the separation ability of ionic liquids is in the order of [C₂MIM]⁺[BF₄]⁻ < [C₄MIM]⁺[BF₄]⁻ ≈ [C₂MIM]⁺[N(CN)₂]⁻ < [C₈MIM]⁺[BF₄]⁻ < [C₈Chin]⁺[BTA]⁻. The liquid demixing effect should be taken into account. The activity coefficients of 1-hexene and n-hexane at infinite dilution calculated with the COSMO-RS model were correlated using the NRTL, Wilson and UNIQUAC model. In this work the predictive results from the COSMO-RS model and UNIFAC model for the 1-hexene/n-hexane and 1-hexene/n-hexane/NMP systems were compared. The UNIFAC model is one of the most important academic contributions by Prof. Jürgen Gmehling.     

Syntheses and characterization of ANi(AsF6)3 (A = H3O, O2, NO, NH4, K, Rb, and Cs) compounds

ANi(AsF₆)₃ (A = O₂⁺, NO⁺, NH₄⁺) compounds could be prepared by reaction between corresponding AAsF₆ salts and Ni(AsF₆)₂. When mixtures of AF (A = Li, Na, K, Rb, Cs) and NiF₂ are dissolved in aHF acidified with an excess of AsF₅ the corresponding AAsF₆ and Ni(AsF₆)₂ were formed in situ. For A = Li and Na only mixtures of AAsF₆ and Ni(AsF₆)₂ were obtained, while for A = K, Rb and Cs, the final products were ANi(AsF₆)₃ (A = K-Cs) compounds contaminated with AAsF₆ (A = K-Cs) and Ni(AsF₆)₂.ANi(AsF₆)₃ (A = H₃O⁺, O₂⁺, NO⁺, NH₄⁺ and K⁺) compounds are structurally related to previously known H₃OCo(AsF₆)₃. The main features of the structure of these compounds are rings of NiF₆ octahedra sharing apexes with AsF₆ octahedra connected into infinite tri-dimensional network. In this arrangement cavities are formed where single charged cations are placed.In O₂Ni(AsF₆)₃ the vibrational band belonging to O₂⁺ vibration is found at 1866 cm⁻¹, which is according to the literature data one of the highest known values, and it is only 10 cm⁻¹ lower than the value for free O₂⁺.     

Thermodynamic representation of the NaCl + Na2SO4 + H2O system with electrolyte NRTL model

A comprehensive thermodynamic model based on the electrolyte NRTL (eNRTL) activity coefficient equation is developed for the NaCl + H₂O binary, the Na₂SO₄ + H₂O binary and the NaCl + Na₂SO₄ + H₂O ternary. The NRTL binary parameters for pairs H₂O-(Na⁺, Cl⁻) and H₂O-(Na⁺, SO₄²⁻), and the aqueous phase infinite dilution heat capacity parameters for ions Cl⁻ and SO₄²⁻ are regressed from fitting experimental data on mean ionic activity coefficient, heat capacity, liquid enthalpy and dissolution enthalpy for the NaCl + H₂O binary and the Na₂SO₄ + H₂O binary with electrolyte concentrations up to saturation and temperature up to 473.15 K. The Gibbs energy of formation, enthalpy of formation and heat capacity parameters for solids NaCl_(s), NaCl·2H₂O_(s), Na₂SO_4(s) and Na₂SO₄·10H₂O_(s) are obtained by fitting experimental data on solubilities of NaCl and Na₂SO₄ in water. The NRTL binary parameters for the (Na⁺, Cl⁻)-(Na⁺, SO₄²⁻) pair are regressed from fitting experimental data on dissolution enthalpies and solubilities for the NaCl + Na₂SO₄ + H₂O ternary.     

A multisyringe sequential injection method for monitoring water in the energy cogeneration system of a municipal waste incinerator

Leading-edge urban solid waste ashing plants use burning heat energy to obtain electrical power. Water fed to their boilers for conversion into steam should be highly pure in order to minimize corrosion, scaling and similar phenomena, which can lead to malfunctioning and a reduced useful life but can be avoided by proper management and control of the water supply. In this work, we developed a multiparameter monitor based on multisyringe sequential injection for the sequential determination of up to eight important parameters, namely: pH, specific and acid conductivity, hydrazine, ammonium, phosphate, silicate and total iron.Acid conductivity was determined by passing the sample through a cation-exchange resin in order to retain ammonium ion and release protons. This parameter was deemed the most accurate indicator of dissolved solids in boiler water. Chemical parameters were determined spectrophotometrically: hydrazine by reaction with p-dimethylaminobenzaldehyde, ammonium by the modified Berthelot reaction, iron with o-phenanthroline, and phosphate and silica by formation of a molybdoheteropoly blue dye in the presence of ascorbic acid as reductant. Use of the optimum chemical and physical operating conditions provided 3s_blank detection limits of 0.01 mg l⁻¹ N₂H₄, 0.13 mg l⁻¹ NH₄⁺, 0.04 mg l⁻¹ Fe, 0.03 mg l⁻¹ SiO₂ and 0.05 mg l⁻¹ PO₄³⁻, and relative standard deviations not greater than 2.5%. The methods integrated in the proposed monitor were successfully applied to real samples from the water-steam cycle at the Son Reus ashing plant in Palma de Mallorca (Spain).