Fabrication of poly(ethylene glycol)‐based hydrogels entrapping enzyme‐immobilized silica nanoparticles

In this study, we immobilized enzymes by combining covalent surface immobilization and hydrogel entrapment. A model enzyme, glucose oxidase (GOX), was first covalently immobilized on the surface of silica nanoparticles (SNPs) via 3‐aminopropyltriethoxysilane (APTES), and the resultant SNP‐immobilized enzyme was physically entrapped within photopolymerized hydrogels prepared from two different molecular weights (MWs) (575 and 8000 Da) of poly(ethylene glycol)(PEG). The hydrogel entrapment resulted in a decrease in reaction rate and an increase in apparent K_m of SNP‐immobilized GOX, but these negative effects could be minimized by using hydrogel with a higher MW PEG, which provides higher water content and larger mesh size. The catalytic rate of the PEG 8000 hydrogel was about ten times faster than that of the PEG 575 hydrogel because of enhanced mass transfer. Long‐term stability test demonstrated that SNP‐immobilized GOX entrapped within hydrogel maintained more than 60% of its initial activity after a week, whereas non‐entrapped SNP‐immobilized GOX and entrapped GOX without SNP immobilization maintained less than 20% of their initial activity. Incorporation of SNPs into hydrogel enhanced the mechanical strength of the hydrogel six‐fold relative to bare hydrogels. Finally, a hydrogel microarray entrapping SNP‐immobilized GOX was fabricated using photolithography and successfully used for quantitative glucose detection. Copyright © 2009 John Wiley & Sons, Ltd.     

Bicontinuous gyroidal mesoporous carbon matrix for facilitating protein electrochemical and bioelectrocatalytic performances

A strategy of protein-entrapment in bicontinuous gyroidal mesoporous carbon (BGMC) nanocomposite films is described. Herein, the quasi-reversible electron transfer of redox proteins (such as glucose oxidase and myoglobin) is probed and the associated biocatalytic activity is revealed. The apparent heterogeneous electron transfer rate constant of the immobilized glucose oxidase is up to 9.4 s⁻¹, much larger than those in carbon nanotubes and some conventional mesoporous carbons. The BGMC based glucose biosensor enables the determination of glucose at a potential of 0.6 V (vs. SCE). Its detection limit is 1.0 × 10⁻⁵ M (signal-to-noise ratio, S/N = 3), the linear response is up to 7.49 mM and the detection sensitivity is 52.5 nA mM⁻¹ Furthermore, a series of BGMCs with different pore sizes is designed and synthesized using sucrose or phenol formaldehyde resin to study the influences of pore sizes and carbon sources on the immobilization of redox proteins and on the heterogeneous electron transfer.     

Sulfonated polyaniline network grafted multi-wall carbon nanotubes for enzyme immobilization, direct electrochemistry and biosensing of glucose

A new nanomaterial was prepared by grafting a layer of sulfonated polyaniline network (SPAN-NW) on to the surface of multi-walled carbon nanotube (MWNT) and effectively utilized for immobilization of an enzyme and for the fabrication of a biosensor. SPAN-NW was formed on the surface of MWNT by polymerizing a mixture of diphenyl amine 4-sulfonic acid (DPASA), 4-vinyl aniline (VA) and 2-acrylamido-2-methyl-1-propane sulfonic acid (APASA) in the presence of amine functionalized MWNT (MWNT-NH₂). The MWNT-g-SPAN-NW was immobilized with glucose oxidase (GOx) to fabricate the SPAN-NW/GOx biosensor. MWNT-g-SPAN-NW/GOx electrode showed direct electron transfer (DET) for GOx with a fast heterogeneous electron transfer rate constant (k_s) of 4.11 s^− 1. The amperometric current response of MWNT-g-SPAN-NW/GOx biosensor shows linearity up to 9 mM of glucose, with a correlation coefficient of 0.99 and a detection limit of 0.11 μM (S/N = 3). At a low applied potential of − 0.1 V, MWNT-g-SPAN-NW/GOx electrode possesses high sensitivity (4.34 μA mM^− 1) and reproducibility towards glucose.     

Platinum nanoparticles functionalized nitrogen doped graphene platform for sensitive electrochemical glucose biosensing

In this work, we reported an efficient platinum nanoparticles functionalized nitrogen doped graphene (PtNPs@NG) nanocomposite for devising novel electrochemical glucose biosensor for the first time. The fabricated PtNPs@NG and biosensor were characterized using transmission electron microscopy, high-resolution transmission electron microscopy, X-ray photoelectron spectroscopy, static water contact angle, UV–vis spectroscopy, electrochemical impedance spectra and cyclic voltammetry, respectively. PtNPs@NG showed large surface area and excellent biocompatibility, and enhanced the direct electron transfer between enzyme molecules and electrode surface. The glucose oxidase (GOx) immobilized on PtNPs@NG nanocomposite retained its bioactivity, and exhibited a surface controlled, quasi-reversible and fast electron transfer process. The constructed glucose biosensor showed wide linear range from 0.005 to 1.1 mM with high sensitivity of 20.31 mA M⁻¹ cm⁻². The detection limit was calculated to be 0.002 mM at signal-to-noise of 3, which showed 20-fold decrease in comparison with single NG-based electrochemical biosensor for glucose. The proposed glucose biosensor also demonstrated excellent selectivity, good reproducibility, acceptable stability, and could be successfully applied in the detection of glucose in serum samples at the applied potential of −0.33 V. This research provided a promising biosensing platform for the development of excellent electrochemical biosensors.     

Surface plasmon resonance biosensor for enrofloxacin based on deoxyribonucleic acid

A DNA-based surface plasmon resonance biosensor for enrofloxacin was developed. Heating denatured DNA immobilized on the gold-coated glass surface was exploited. The immobilization was performed by a layer-by-layer co-deposition with a cationic polymer. The sensor performance was tested with real biological probes. Direct and simple determination of enrofloxacin in milk samples was demonstrated. The sensor response obeys Langmuir binding isotherm being almost linear until about 20 μg mL⁻¹. The detection limit in milk samples was estimated to be 3 μg mL⁻¹.     

Sensitivity of microarray based immunoassays using surface-attached hydrogels

A promising pathway to improve on the sensitivity of protein microarrays is to immobilize the capture antibodies in a three dimensional hydrogel matrix. We describe a simple method based on printing of an aqueous protein solution containing a photosensitive polymer and the capture antibody onto a plastic chip surface. During short UV-exposure photocrosslinking occurs, which leads to formation of a hydrogel, which is simultaneously bound to the substrate surface. In the same reaction the antibody becomes covalently attached to the forming hydrogel. As the capture antibodies are immobilized in the three-dimensional hydrogel microstructures, high fluorescence intensities can be obtained. The chip system is designed such, that non-specific protein adsorption is strongly prevented. Thus, the background fluorescence is strongly reduced and very high signal-to-background ratios are obtained (SBR > 6 for c_BSA = 1 pM; SBR > 100 for c_BSA > 100 pM). The kinetics of antigen binding to the arrayed antibodies can be used to determine the concentration of a specific protein (for example the tumor marker β₂-microglobulin) in solution for a broad range of analyte concentrations. By varying size and composition of the protein-filled hydrogel microstructures as well as adjusting the extent of labeling it is possible to easily adapt the surface concentration of the probe molecules such that the fluorescence signal intensity is tuned to the prevalence of the protein in the analyte. As a consequence, the signal tuning allows to analyze solutions, which contain both proteins with high (here: upper mg mL⁻¹ range) and with very low concentrations (here: lower μg mL⁻¹ range). This way quantitative analysis with an exceptionally large dynamic range can be performed.     

Nanocomposite based on depositing platinum nanostructure onto carbon nanotubes through a one-pot, facile synthesis method for amperometric sensing

Platinum nanoparticles (Pt NPs) were deposited onto multi-walled carbon nanotubes (MWNTs) through direct chemical reduction without any other stabilizing agents. Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry were employed to characterize the morphology of the as-prepared nanocomposite (noted as Pt NPs-MWNTs) and further identify the Pt NPs on the surface of MWNTs. The nanocomposite demonstrated the ability to electrocatalyze the oxidation of hydrogen peroxide and substantially raises the response current. A sensitivity of 591.33 μA mM⁻¹ cm⁻² was obtained at Pt NPs-MWNTs modified electrode. Thus, we immobilized glucose oxidase (GOD) as a model enzyme on the nanocomposite-based electrode with a thin layer of Nafion to fabricate a glucose biosensor, which showed sensitive and fast response to glucose. The influence of the GOD loading was investigated and the biosensor with an enzyme loading concentration of 10 mg/mL shows optimal performance for glucose detection, that is, a detection limit of 3 μM and a response time of 3 s, respectively.     

Biosensors for determination of glucose with glucose oxidase immobilized on an eggshell membrane

A glucose biosensor using an enzyme-immobilized eggshell membrane and oxygen electrode for glucose determination has been fabricated. Glucose oxidase was covalently immobilized on an eggshell membrane with glutaraldehyde as a cross-linking agent. The glucose biosensor was fabricated by positioning the enzyme-immobilized eggshell membrane on the surface of a dissolved oxygen sensor. The detection scheme was based on the depletion of dissolved oxygen content upon exposure to glucose solution and the decrease in the oxygen level was monitored and related to the glucose concentration. The effect of glutaraldehyde concentration, pH, phosphate buffer concentration and temperature on the response of the glucose biosensor has been studied in detail. Common matrix interferents such as ethanol, d-fructose, citric acid, sodium benzoate, sucrose and l-ascorbic acid did not give significant interference. The resulting sensor exhibited a fast response (100 s), high sensitivity (8.3409 mg L⁻¹ oxygen depletion/mmol L⁻¹ glucose) and good storage stability (85.2% of its initial sensitivity after 4 months). The linear response is 1.0×10⁻⁵ to 1.3×10⁻³ mol L⁻¹ glucose. The glucose content in real samples such as commercial glucose injection preparations and wines was determined, and the results were comparable to the values obtained from a commercial glucose assay kit based on a spectrophotometric method.     

An electrochemiluminescent biosensor for glucose based on the electrochemiluminescence of luminol on the nafion/glucose oxidase/poly(nickel(II)tetrasulfophthalocyanine)/multi-walled carbon nanotubes modified electrode

A poly(nickel(II) tetrasulfophthalocyanine)/multi-walled carbon nanotubes composite modified electrode (polyNiTSPc/MWNTs) was fabricated by electropolymerization of NiTSPc on MWNTs-modified glassy carbon electrode (GCE). The modified electrode was found to be able to greatly improve the emission of luminol electrochemiluminescence (ECL) in a solution containing hydrogen peroxide. Glucose oxidase (GOD) was immobilized on the surface of polyNiTSPc/MWNTs modified GC electrode by Nafion to establish an ECL glucose sensor. Under the optimum conditions, the linear response range of glucose was 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 8.0 × 10⁻⁸ mol L⁻¹ (defined as the concentration that could be detected at the signal-to-noise ratio of 3). The ECL sensor showed an outstanding well reproducibility and long-term stability. The established method has been applied to determine the glucose concentrations in real serum samples with satisfactory results.     

Electrochemistry and biosensing of glucose oxidase based on mesoporous carbons with different spatially ordered dimensions

A strategy of protein entrapment within mesoporous carbon matrices is demonstrated to probe the electrochemistry of glucose oxidase. Large surface area and remarkable electro-catalytic properties of carbon mesoporous materials make them suitable candidates for high loading of protein molecules and the promotion of heterogeneous electron transfer. In this work, two kinds of mesoporous carbon nanocomposite films were designed and prepared with highly ordered two-dimensional (2D) and three-dimensional (3D) structures for the immobilization of glucose oxidase, in which the quasi-reversible electron transfer of the redox enzyme was probed, and the apparent heterogeneous electron transfer rate constants () are 3.9 and 4.2 s⁻¹, respectively. Furthermore, the associated biocatalytic activity was also revealed. Highly ordered 3D-mesoporous carbon material exhibited larger adsorption capacity for glucose oxidase and the immobilized enzymes retained a higher bioactivity compared with 2D-mesoporous carbons. The preparation of protein-entrapped mesoporous carbon nanocomposites expands the scope of carbon-based electrochemical devices and opens a new avenue for the development of biosensors.     

Direct electron transfer of glucose oxidase and dual hydrogen peroxide and glucose detection based on water-dispersible carbon nanotubes derivative

A water-dispersible multi-walled carbon nanotubes (MWCNTs) derivative, MWCNTs-1-one-dihydroxypyridine (MWCNTs-Py) was synthesis via Friedel–Crafts chemical acylation. Raman spectra demonstrated the conjugated level of MWCNTs-Py was retained after this chemical modification. MWCNTs-Py showed dual hydrogen peroxide (H₂O₂) and glucose detections without mutual interference by adjusting pH value. It was sensitive to H₂O₂ in acidic solution and displayed the high performances of sensitivity, linear range, response time and stability; meanwhile it did not respond to H₂O₂ in neutral solution. In addition, this positively charged MWCNTs-Py could adsorb glucose oxidase (GOD) by electrostatic attraction. MWCNTs-Py-GOD/GC electrode showed the direct electron transfer (DET) of GOD with a pair of well-defined redox peaks, attesting the bioactivity of GOD was retained due to the non-destroyed immobilization. The high surface coverage of active GOD (3.5 × 10⁻⁹ mol cm⁻²) resulted in exhibiting a good electrocatalytic activity toward glucose. This glucose sensor showed high sensitivity (68.1 μA mM⁻¹ cm⁻²) in a linear range from 3 μM to 7 mM in neutral buffer solution. The proposed sensor could distinguish H₂O₂ and glucose, thus owning high selectivity and reliability.     

Bienzymatic amperometric biosensor for glucose based on polypyrrole/ceramic carbon as electrode material

A novel amperometric biosensor utilizing two enzymes, glucose oxidase (GOD) and horseradish peroxidase (HRP), was developed for the cathodic detection of glucose. The glucose biosensor was constructed by electrochemical formation of a polypyrrole (PPy) membrane in the presence of GOD on the surface of a HRP-modified sol-gel derived-mediated ceramic carbon electrode. Ferrocenecarboxylic acid (FCA) was used as mediator to transfer electron between enzyme and electrode. In the hetero-bilayer configuration of electrode, all enzymes were well immobilized in electrode matrices and showed favorable enzymatic activities. The amperometric detection of glucose was carried out at +0.16 V (versus saturated calomel reference electrode (SCE)) in 0.1 M phosphate buffer solution (pH 6.9) with a linear response range between 8.0×10⁻⁵ and 1.3×10⁻³ M glucose. The biosensor showed a good suppression of interference in the amperometric detection.     

Successive determination of urinary protein and glucose using spectrophotometric sequential injection method

A new sequential injection (SI) system with spectrophotometric detections has been developed for successive determination of protein and glucose. The protein assay is based on ion-association of protein with tetrabromophenolphthalein ethyl ester (TBPE) in the presence of Triton X-100 at pH 3.2. The blue product is monitored for absorbance at 607 nm. For glucose, hydrogen peroxide, generated by the oxidation of glucose in the presence of glucose oxidase immobilized on glass beads packed in a minicolumn, is monitored using iron-catalyzed oxidation reaction of p-anisidine to form a red colored product (520 nm). The SI procedure takes advantage in performing the protein assay during the incubation period for glucose oxidation. Linear ranges were up to 10 mg dL⁻¹ human serum albumin (HSA) with a limit of detection (LOD) (3σ) of 0.3 mg dL⁻¹, and up to 12.5 mg dL⁻¹ glucose with LOD of 0.08 mg dL⁻¹. R.S.D.s (n = 11) were 2.7% and 2.5% (for 1 mg dL⁻¹ and 5 mg dL⁻¹ HSA) and 1.4% (9 mg dL⁻¹ glucose). Sample throughput for the whole assay of both protein and glucose is 6 h⁻¹. The automated system has been demonstrated for the successive assay of protein and glucose in urine samples taken from diabetic disease patients, with good agreement with the other methods. This developed SI system is an alternative automation for screening for diabetic diagnosis.     

Glucose concentration determination based on silica sol-gel encapsulated glucose oxidase optical biosensor arrays

Optical biosensor arrays for rapidly determining the glucose concentrations in a large number of beverage and blood samples were developed by immobilizing glucose oxidase (GOD) on oxygen sensor layer. Glucose oxidase was first encapsulated in silica based gels through sol-gel approach and then immobilized on 96-well microarrays integrated with oxygen sensing film at the bottom. The oxygen sensing film was made of an organically modified silica film (ORMOSIL) doped with tris(4,7-diphenyl-1,10-phenanthroline) ruthenium dichloride (Ru(dpp)₃Cl₂). The oxidation reaction of glucose by glucose oxidase could be monitored through fluorescence intensity enhancement due to the oxygen consumption in the reaction. The luminescence changing rate evaluated by the dynamic transient method (DTM) was correlated with the glucose concentration with the wide linear range from 0.1 to 5.0 mM (Y = 13.28X − 0.128, R = 0.9968) and low detection limit (0.06 mM). The effects of pH and coexisting ions were systemically studied. The results showed that the optical biosensor arrays worked under a wide range of pH value, and normal interfering species such as Na⁺, K⁺, Cl⁻, PO₄³⁻, and ascorbic acid did not cause apparent interference on the measurement. The activity of glucose oxidase was mostly retained even after 2-month storage, indicating their long-term stability.     

A novel procedure for rapid surface functionalisation and mediator loading of screen-printed carbon electrodes

We report a simple and rapid procedure that leads to incorporation of mediator and introduction of amine functionality onto the surface of screen-printed carbon electrodes (SPCE). The electrodes were doped with cobalt phthalocyanine (CoPc) by enhanced adsorption in a process that uses minimal amounts of this redox mediator as compared with CoPc loaded inks. The CoPc-doped SPCE showed a substantially increased sensitivity to hydrogen peroxide and thiocholine as compared to unmodified electrodes. This greatly facilitated their use as transducers for the construction of amperometric biosensors based on enzymes producing oxidizable products such as hydrogen peroxide or thiols. Immobilisation of enzymes including glucose oxidase, acetylcholinesterase and choline oxidase was achieved through their multi-contact electrostatic interaction with polyethyleneimine (PEI) which was electrodeposited on the surface of CoPc-doped electrodes in one step from ethanolic solution. The efficiency of enzyme immobilisation was shown to depend on the molecular weight of the PEI used, reaching a maximum for 25 kDa PEI. The biosensors shown sensitivity to glucose at 130 nA mM⁻¹ (LOD 0.15 mM) and to acetylcholine at 70 nA mM⁻¹ (LOD 0.10 mM) under +0.6 V. Detection of glucose has been demonstrated at +0.4 V with the sensitivity of 60 nA mM⁻¹ and LOD of 0.33 mM. Possibility of the inhibition analysis of pesticides has been shown for acetylcholinesterase-based sensors.     

Inhibition biosensor for determination of nicotine

An amperometric nicotine inhibition biosensor has been substantially simplified and used for determination of nicotine in tobacco sample. Besides the use of single enzyme choline oxidase to replace bienzyme, the use of 1,4-benzoquinone as an electron mediator makes it possible to avoid the use of oxygen or hydrogen peroxide sensor as the internal transducer. Choline oxidase was immobilized on the carbon paste electrode through cross-linking with bovine serum albumin (BSA) by glutaraldehyde. In the presence of choline oxidase and its endogenous cofactor flavin-ademine dinneleotide (FAD), choline was oxidized into betaine while FAD was reduced to FADH₂ which subsequently reduced 1,4-benzoquinone into hydroquinone. The later was finally oxidized at a relatively low potential of +450 mV versus saturated calomel electrode (SCE). Nicotine inhibits the activity of enzyme with an effect of decreasing of oxidation current. The experimental conditions were optimized. The electrode has a linear response to choline within 1.25×10⁻⁴ to 1.25×10⁻³ mol l⁻¹. The nicotine measurements were carried out in 0.067 mol l⁻¹phosphate buffer of pH 7.4 at an applied potential of 450 mV versus SCE. The electrode provided a linear response to nicotine over a concentration range of 2.0×10⁻⁵ to 9.2×10⁻⁴ mol l⁻¹ with a detection limit of 1.0×10⁻⁵ mol l⁻¹. The system was applied to the determination of nicotine in tobacco samples.     

A phenol biosensor based on immobilizing tyrosinase to modified core-shell magnetic nanoparticles supported at a carbon paste electrode

A phenol biosensor was developed based on the immobilization of tyrosinase on the surface of modified magnetic MgFe₂O₄ nanoparticles. The tyrosinase was first covalently immobilized to core-shell (MgFe₂O₄-SiO₂) magnetic nanoparticles, which were modified with amino group on its surface. The resulting magnetic bio-nanoparticles were attached to the surface of carbon paste electrode (CPE) with the help of a permanent magnet. The immobilization matrix provided a good microenvironment for the retaining of the bioactivity of tyrosinase. Phenol was determined by the direct reduction of biocatalytically generated quinone species at −150 mV versus SCE. The resulting phenol biosensor could reach 95% of steady-state current within 20 s and exhibited a high sensitivity of 54.2 μA/mM, which resulted from the high tyrosinase loading of the immobilization matrix. The linear range for phenol determination was from 1 × 10⁻⁶ to 2.5 × 10⁻⁴ M with a detection limit of 6.0 × 10⁻⁷ M obtained at a signal-to-noise ratio of 3. The stability and the application of the biosensor were also evaluated.     

Glucose and urea biosensors based on all solid-state PVC-NH2 membrane electrodes

Miniaturized urea and glucose sensors prepared by immobilization of glucose oxidase or urease directly onto all solid-state contact PVC-NH₂ membrane ammonium and hydrogen ion selective electrodes are described. The resulting biosensing membranes function equivalently to normal PVC membranes in terms of potentiometric response properties. The most important features of the glucose and urea sensors were high sensitivity, long life-time, easily built at a low cost, micro-construction and short response time. The characteristics of the glucose and urea sensors were examined in several buffer solutions at different concentrations and pH values. The influence of immobilization conditions on the dynamic response properties and life-time of the electrodes was studied. Under optimal conditions, the urea electrode showed a linear response between 5×10⁻² and 5×10⁻⁴ M urea, while the glucose electrode showed a linear response between 5×10⁻² and 1×10⁻⁴ M glucose.     

A comparative analysis of polyurethane hydrogel for immobilization of IgG on chips

Hydrogels are considered an optimum material for protein chip surfaces, since they provide a quasi-liquid environment which allows protein activity to be maintained and shows good spot morphology as well as excellent immobilization capacity. In the following, we present a polyurethane (PU) chip that electrostatically binds IgG. The PU surface is optimized with regard to layer thickness (∼200 nm), hydrogel (2%) and immobilized antibody concentration (0.5 mg mL⁻¹; 0.3 ng spot⁻¹), pH and ionic strength of the print buffer as well as to blocking solution. Evaluation is done in a direct IgG immunoassay using the Nexterion slide H as a reference. It is shown that higher IgG loading is achieved on the PU chip than on slide H, no matter whether 1× PBS (pH 7.2), Sörensen (pH 5.8) or Nexterion buffer was used as a spotting solution. Moreover, the crossreactivity with goat IgG, human IgG and monoclonal anti-CRP spotted in Nexterion buffer was as low as ≤0.74% (slide H: ≤3.34%).     

A new polyethylene glycol fiber prepared by coating porous zinc electrodeposited onto silver for solid-phase microextraction of styrene

A new polyethylene glycol fiber was developed for solid-phase microextraction (SPME) of styrene by electrodepositing porous Zn film on Ag wire substrate followed by coating with polyethylene glycol sol-gel (Ag/Zn/PEG sol-gel fiber). The scanning electron micrographs of fibers surface revealed a highly porous structure. The extraction property of the developed fiber-to-styrene residue from polystyrene packaged food was investigated by headspace solid-phase microextraction (HS-SPME) and analyzed with a gas chromatograph coupled with flame ionization detection (GC-FID). The new Ag/Zn/PEG sol-gel fiber is simple to prepare, low cost, robust, has high thermal stability and long lifetime, up to 359 extractions. Repeatability of one fiber (n = 6) was in the range of 4.7-7.5% and fiber-to-fiber reproducibility (n = 4) for five concentration values were in the range 3.4-10%. This Ag/Zn/PEG sol-gel fiber was compared to two commercial SPME fibers, 75 μm carboxen/polydimethylsiloxane (CAR/PDMS) and 100 μm polydimethylsiloxane (PDMS). Under their optimum conditions, Ag/Zn/PEG sol-gel fiber showed the highest sensitivity and the lowest detection limit at 0.28 ± 0.01 ng mL⁻¹.