Pressurized liquid extraction of isoflavones from soybeans

Isoflavone derivatives from freeze-dried soybeans were extracted by pressurized liquid extraction (PLE) and determined by reverse-phase high performance liquid chromatography (HPLC) with both photo diode array and mass spectrometry (MS) detection. Both real and spiked samples were used in the development of the method.Several extraction solvents (methanol (MeOH) and ethanol (EtOH), 30-80% in water and water), temperatures (60-200 °C), pressures (100-200 atm), as well as the sample size (0.5-0.05 g) and cycle length (5-10 min) were studied for the optimization of the extraction protocol. The optimized extraction conditions for quantitative recoveries were: 0.1 g of sample, 100 °C, three (7 min) static extraction cycles and ethanol 70% as extracting solvent. The stability of the isoflavones during the PLE was also determined. Under PLE conditions, degradation of malonyl glucoside forms of the isoflavones takes place using temperatures higher than 100 °C whereas degradation of glucosides takes place above 150 °C. Using the optimized protocol, isoflavones can be extracted from freeze-dried soybeans without degradation.     

Ultrasonic extraction of veterinary antibiotics from soils and pig slurry with SPE clean-up and LC-UV and fluorescence detection

A simple and rapid analytical method is presented in which the three veterinary antibiotics oxytetracycline (OTC), sulfachloropyridazine (SCP) and tylosin (TYL) are simultaneously extracted and determined in four different soils. Extractions were carried out by a combination of ultrasonic agitation and vortex mixing using a mixture of methanol, EDTA and McIlvaine buffer at pH 7 as the extractant solution. The extracts were then cleaned-up by a tandem solid phase extraction (SPE) method using an Isolute SAX anion exchange cartridge to remove natural organic matter and an Oasis HLB polymeric cartridge to retain the study compounds. Analysis was by HPLC-UV with additional fluorescence detection for SCP. Recoveries were in the range 68-85% for SCP in all soil types, 58-75% for OTC in sandy soils, 27-51% for OTC in clay containing soils, 74-105% for TYL and 47-61% in a clay soil. OTC and SCP were also extracted from liquid pig manure using a mixture of EDTA and McIlvaine buffer at pH 7 with ultrasonic agitation and vortex mixing with SPE clean-up and HPLC-UV analysis. Recoveries were greater than 77% and 58% for OTC and SCP, respectively. Limits of detection were 18 μg kg⁻¹ for OTC and SCP and 40 μg kg⁻¹ for TYL in soils and 70 μg L⁻¹ for OTC and 140 μg L⁻¹ for SCP in pig slurry.     

Simultaneous residue monitoring of four tetracycline antibiotics in fish muscle by in-tube solid-phase microextraction coupled with high-performance liquid chromatography

An on-line simple and rapid method for the simultaneous determination of tetracycline (TC), oxytetracycline (OTC), chlortetracycline (CTC) and doxycycline (DC) residues in fish muscle was developed by coupling in-tube solid-phase microextraction (SPME) to high-performance liquid chromatography (HPLC) with a photodiode array detector. Biocompatible poly (methacrylic acid-ethylene glycol dimethacrylate) monolithic capillary was selected as the extraction medium, and no precipitating protein and removing fat steps were required prior to extraction. In order to optimize the extraction of these compounds, several in-tube SPME parameters were investigated. Simply performed by extracting with 0.01 M EDTA-MacIlvaine buffer solution (pH 4.0) and centrifugation, the sample then could be directly injected into the device for extraction. The limits of detection of tetracycline, oxytetracycline, chlortetracycline and doxycycline were calculated to be 22, 16, 30 and 21 ng/g, respectively. The calibration curves showed linearity in the range of 100-10,000 ng/g with a linear coefficient R² value above 0.9980. Excellent method reproducibility was found by intra- and inter-day precisions, yielding the R.S.D.s less than 4.22% and 5.71%, respectively.     

Analysis of oxytetracycline, tetracycline, and chlortetracycline in water using solid-phase extraction and liquid chromatography-tandem mass spectrometry

A method using liquid chromatography-tandem mass spectrometry has been developed for determination of trace levels of tetracycline antibiotics in ground water and confined animal feeding operation waste water. Oxytetracycline (OTC), tetracycline (TC), and chlortetracycline (CTC) were extracted from water samples using both polymeric and C18 extraction cartridges. The addition of a buffer containing potassium phosphate and citric acid improved tetracycline recoveries in lagoon water. Method detection limits determined in reagent water fortified with 1 microg l(-1) OTC, TC, and CTC were 0.21, 0.20, and 0.28 microg l(-1). Method detection limits in lagoon water samples fortified at 20 microg l(-1) for OTC, TC, and CTC were 3.6, 3.1, and 3.8 microg l(-1). Variability in recovery from laboratory fortified blanks ranged from 86 to 110% during routine analysis.     

Detection of tetracycline and oxytetracycline residues in pig and calf hair by ultra-high-performance liquid chromatography tandem mass spectrometry

An ultra-high-performance liquid chromatography tandem mass spectrometry method to detect residues of tetracycline (TC), epi-tetracycline (eTC) and oxytetracycline (OTC) in animal hair was developed. Hair samples were washed with water, extracted with NH₄OH 0.1 M, purified by SPE-C₁₈ cartridge and analyzed by tandem mass spectrometry (ESI⁺, MRM mode) with satisfactory results. For the first time, accumulation of TC, eTC and OTC was confirmed in livestock hairs after a therapeutic treatment with TC and OTC, respectively. Administered drug residues were detectable in hair samples up to 2 months after the last treatment, providing a retrospective evidence of TC and OTC administration. Hair analysis seems to offer a wider window of detection than edible tissues.     

Simultaneous extraction of organotin, organolead and organomercury species from soils and litter

Extracting organotin compounds (OTC) from soils is difficult due to the high cation exchange and complexation capacity of soils, and little information about OTC in soils is available. In this study, a new extraction method, combining 1 M CaCl₂, 0.1% tropolone, and glacial acetic acid was developed. Recoveries of mono-substituted OTC from spiked plant litter, and soil samples were improved substantially to 40% compared to classical glacial acetic acid extraction commonly used in sedimentology, yielding <10% recovery in C-rich soil samples. Simultaneously, the recovery of other OTC, trimethyllead and monomethylmercury was satisfactory. The recoveries of most species from the spiked litter, upland and wetland soils exceeded 70%. The new method extracted much more organometallics from unspiked organic soils and litter than microwave- and ultrasound-assisted extraction and accelerated solvent extraction, most likely due to exchange of organometallics from the solid phase by Ca²⁺. The method is simple, highly efficient and with low contamination. Together with GC-ICP-mass spectrometry, the method allows the detection of these organometallics in the pg g⁻¹ range and it is particularly suitable for soil and plant materials with low organometallics contents.     

Pressurized liquid extraction of organophosphate triesters from sediment samples using aqueous solutions

A novel procedure for the extraction of seven organophosphate triesters (OPs), used as flame retardants and plasticizers, from sediment samples has been developed. It is based on the pressurized liquid extraction of the analytes with aqueous solutions, combined with a further concentration step using solid-phase extraction (SPE) and followed by gas chromatography coupled to mass spectrometry (GC-MS) determination. The effects of different variables on the yield and selectivity of the sample preparation process are systematically evaluated. The optimal responses were observed extracting 2 g of sediment with a water:acetonitrile (75:25) solution at 90 °C and 1500 psi for 5 min. The obtained extract was made up to 200 mL with ultrapure water and passed through an OASIS HLB, 60 mg cartridge. Analytes were recovered with 2 mL of ethyl acetate and this extract concentrated to a lower volume, ca. 0.2 mL. Recoveries of the proposed extraction method ranged from 77 to 111%, with relative standard deviations below 10%, for spiked river and marine sediment samples with total carbon contents (TC) up to 4.0%. The limits of quantification (LOQs) of the method varied between 0.5 and 5 ng g⁻¹. Analysis of non-spiked sediment samples revealed the presence of low levels for some of the investigated species, with the highest concentration (47 ng g⁻¹) corresponding to tris(2-chloroethyl) phosphate (TCEP).     

An electrochemically enhanced solid-phase microextraction approach based on molecularly imprinted polypyrrole/multi-walled carbon nanotubes composite coating for selective extraction of fluoroquinolones in aqueous samples

In this study, an electrochemically enhanced solid-phase microextraction (EE-SPME) approach based on molecularly imprinted polypyrrole/multi-walled carbon nanotubes (MIPPy/MWCNTs) composite coating on Pt wire was developed for selective extraction of fluoroquinolone antibiotics (FQs) in aqueous samples. During the extraction, a direct current potential was applied to the MIPPy/MWCNTs/Pt fiber as working electrode in a standard three-electrode system, FQ ions suffered electrophoretic transfer to the coating surface and then entered into the shape-complimentary cavities by hydrogen-bonding and ion-exchange interactions. After EE-SPME extraction, the fiber was desorbed with desorption solvent for high-performance liquid chromatography (HPLC) analysis. Some parameters influencing EE-SPME extraction such as applied potential, extraction time, solution pH, ionic strength, and desorption solvent were optimized. EE-SPME showed good selectivity and higher extraction efficiency to FQs compared with that of traditional solid-phase microextraction. EE-SPME coupled with HPLC to determine FQs in water samples, the limits of detection (S/N = 3) for the selected FQs are 0.5–1.9 μg L⁻¹. The proposed method was successfully used to the analysis of FQs spiked urine and soil samples, with recoveries of 85.1–94.2% for the urine samples and 89.8–95.5% for the soil samples.     

Application of enzymatic probe sonication extraction for the determination of selected veterinary antibiotics and their main metabolites in fish and mussel samples

A new method based on enzymatic probe sonication extraction prior to high-performance liquid chromatography (HPLC) has been developed for the determination of 11 antibiotics (drugs) and the main metabolites of five of them in fish tissue and mussel samples. The analytes belong to four different classes of antibiotics (sulfonamides, tetracyclines, penicillins and amphenicols). The analysed compounds were sulfadiazine (SDI) and N⁴-acetylsulfadiazine (NDI) metabolite, sulfamethazine (SMZ) and N⁴-acetylsulfamethazine (NMZ), sulfamerazine (SMR) and N⁴-acetylsulfamerazine (NMR), sulfamethoxazole (SMX), trimetroprim (TMP), amoxicillin (AMX) and its main metabolite amoxicilloic acid (AMA), ampicillin (AMP) and its main metabolite ampicilloic acid (APA), chloramphenicol (CLF), thiamphenicol (TIF), oxytetracycline (OXT) and chlortetracycline (CLT).The main factors affecting the extraction efficiency (type of enzyme, type and volume of extractant, ultrasounds power and extraction time) were optimised in tissue of hake (Merluccius merluccius), anchovy (Engraulis encrasicolus), mussel (Mytilus sp.) and wedge sole (Solea solea). The extraction was carried out using an extraction time of 5 min with 5 mL of water and subsequent clean-up with dichloromethane.High-performance liquid chromatography (HPLC) with diode array (DAD) and fluorescence (FLD) detectors was used for the determination of the antibiotics. The separation of the analysed compounds was conducted by means of a Phenomenex^® Gemini C₁₈ (150 mm × 4.6 mm I.D., particle size 5 μm) analytical column with LiChroCART^® LiChrospher^® C₁₈ (4 mm × 4 mm, particle size 5 μm) guard-column. Analysed drugs were determined using formic acid 0.1% (v/v) in water and acetonitrile in gradient elution mode as mobile phase. The proposed method was also evaluated by a laboratory assay consisting of the determination of the targeted analytes in samples of Cyprinus carpio which had previously administered the antibiotics.     

Analysis of zearalenone and α-zearalenol in animal feed using high-performance liquid chromatography

Different extraction and clean-up techniques used before HPLC analysis were compared in order to obtain a reliable method for the quantitative determination of zearalenone (ZEA) and α-zearalenol (α-ZOL) in animal feed. Immunoaffinity clean-up was compared to C₁₈ and Florisil column clean-up. Extracted samples were analysed by reversed-phase HPLC with fluorescence detection (λ_ex=274 nm, λ_em=440 nm). A mobile phase of acetonitrile:water (50:50 (v/v)) and a flow-rate of 1.0 ml min⁻¹ resulted in a good separation between ZEA and α-ZOL. Using immunoaffinity clean-up the linear range was between 25 and 600 μg kg⁻¹ for ZEA and α-ZOL in maize. Intra-laboratory coefficients of variation (CV) (under repeatability conditions) were 9.16% for ZEA and 2.18% for α-ZOL. Recoveries for spiked ZEA and α-ZOL samples ranged from 89 to 110% with CVs between 5.2 and 11.2% (under within-laboratory reproducibility conditions). Using C₁₈ and Florisil solid-phase clean-up, matrix interference was too high. Therefore, naturally contaminated animal feed samples were analysed using the developed HPLC method coupled to the immunoaffinity clean-up.     

Ultrasound-assisted dispersive liquid–liquid microextraction for the determination of six pyrethroids in river water

A simple ultrasound-assisted dispersive liquid–liquid microextraction method combined with liquid chromatography was developed for the preconcentration and determination of six pyrethroids in river water samples. The procedure was based on a ternary solvent system to formatting tiny droplets of extractant in sample solution by dissolving appropriate amounts of water-immiscible extractant (tetrachloromethane) in watermiscible dispersive solvent (acetone). Various parameters that affected the extraction efficiency (such as type and volume of extraction and dispersive solvent, extraction time, ultrasonic time, and centrifuging time) were evaluated. Under the optimum condition, good linearity was obtained in a range of 0.00059–1.52 mg L⁻¹ for all analytes with the correlation coefficient (r²) > 0.999. Intra-assay and inter-assay precision evaluated as the relative standard deviation (RSD) were less than 3.4 and 8.9%. The recoveries of six pyrethroids at three spiked levels were in the range of 86.2–109.3% with RSD of less than 8.7%. The enrichment factors for the six pyrethroids were ranged from 767 to 1033 folds.     

Simultaneous determination of tetracyclines in poultry muscle by capillary zone electrophoresis

A capillary zone electrophoresis method with UV detection was developed for the simultaneous detection and quantification of three tetracyclines in chicken meat samples: tetracycline (TC), oxytetracycline (OTC) and doxycycline (DOC). The separation conditions were: a running buffer containing 30 mM sodium phosphate, 2 mM EDTA disodium salt and 2.5% 2-propanol, pH 12.0, a 5 s hydrodynamic injection and a 14 kV separation voltage. Two different clean-up methodologies were employed: solid-phase extraction with C₁₈ cartridges and ion exchange with Amberlite XAD7 resin. Analytes were detected at 360 nm in less than 12 min. LODs ranged from 61 μg kg⁻¹ for OTC to 68 μg kg⁻¹ for DOC with C₁₈ cartridges, and 81 μg kg⁻¹ for DOC to 89 μg kg⁻¹ for TC with Amberlite XAD7 resin. The recoveries for TC, OTC and DOC obtained by both methods were between 85 and 95%, and the peak area repeatability for all of the samples was below 5% in all cases. Twenty-four samples of commercial chicken drumsticks were examined with both clean-up methodologies. In nine cases (37.5%) TC was detected, in a range from 197.8 to 2564.3 μg kg⁻¹, and in seven cases (29.2%) OTC was detected in a range from 83.0 to 2049.3 μg kg⁻¹. DOC was not detected in any of the tested samples. This method would be useful for the routine monitoring of TCs residues in poultry muscle.     

Trace determination of 10 β-lactam antibiotics in environmental and food samples by capillary liquid chromatography

A sensitive and reliable method using capillary HPLC with UV-diode array detection (DAD) has been developed and validated for the trace determination of residues of 10 β-lactam antibiotics of human and veterinary use, in milk, chicken meat and environmental water samples. The analytes included ampicillin, amoxicillin, penicillin V, penicillin G, cloxacillin, oxacillin, dicloxacillin, nafcillin, piperacillin and clavulanic acid. Legal levels are regulated by the EU Council regulation 2377/90 in animal edible tissues for these compounds. For food analysis, a solid-phase extraction (SPE) procedure consisting in a tandem of Oasis HLB and Alumina N cartridges was applied for off-line preconcentration and cleanup. For water analysis, the first step was only necessary. The limits of detection for the studied compounds were between 0.04–0.06 μg l⁻¹ for water samples and 0.80–1.40 μg l⁻¹ (or μg kg⁻¹) in the case of foods derived from animals. Average recoveries for fortified samples at different concentration levels ranged between 82.9% and 98.2%, with relative standard deviations (RSDs) lower than 9%. The method showed the advantages of capillary HPLC for the detection of these widely applied antibiotics in different samples at very low concentration levels.     

Optimization of microwave-assisted solvent extraction for volatile organic acids in tobacco and its comparison with conventional extraction methods

In the present study, a new method using microwave-assisted solvent extraction (MASE) technique followed directly GC analysis was developed for the extraction of volatile organic acids (VOAs) in tobacco. The MASE conditions (heating time, volume of extracting solvent and extraction temperature) were optimized by means of an orthogonal array design (OAD) procedure. The results suggested that extractant, temperature and heating time were statistically the most significant factors. The extracts were directly analyzed with capillary GC operating in splitless-injection mode on an Agilent HP-FFAP capillary column. Under optimum operating conditions, MASE showed significantly better recoveries than those obtained by the conventional extraction method (ultrasonic and reflux extraction), ranging from 90.6% to 103.2%. In addition, a drastic reduction of the extraction time (20 min versus 4 h) and solvent consumption (20 mL versus 100 mL) was achieved with an outstanding reproducibility (CV ≤5%).     

Rapid analysis of captopril in human plasma and pharmaceutical preparations by headspace solid phase microextraction based on polypyrrole film coupled to ion mobility spectrometry

A rapid, simple, and sensitive headspace solid phase microextraction coupled to ion mobility spectrometry (HS-SPME-IMS) method is presented for analysis of the highly specific angiotensin-converting enzyme (ACE) inhibitor, captopril (CAP). Positive ion mobility spectra of CAP were acquired with an ion mobility spectrometer equipped with a corona discharge ionization source. Mass-to-mobility correlation equation was used to identify product ions. A dodecylsulfate-doped polypyrrole (PPy-DS) coating was used as a fiber for SPME. The results showed that PPy-DS based SPME fiber was suitable for successfully extracting CAP from human blood plasma and pharmaceutical samples. The HS-SPME-IMS method provided good repeatability (R.S.D.s < 4%) for aqueous and spiked plasma samples. The calibration graphs were linear in the range of 10-300 ng mL⁻¹ (R² > 0.99) and detection limits were 7.5 ng mL⁻¹ for aqueous and 6.3 ng mL⁻¹ for plasma blank samples. Finally, a standard addition calibration method was applied to HS-SPME-IMS technique for the analysis of blood plasma samples and tablets. Purpose method seemed to be suitable for the analysis of CAP in plasma samples as it is not time consuming (state total time from sample preparation to analysis), it required only small quantities of the sample, and no derivatization was required.     

Dispersive liquid–liquid microextraction combined with high-performance liquid chromatography-UV detection as a very simple,rapid and sensitive method for the determination of bisphenol A in water samples

Dispersive liquid–liquid microextraction (DLLME) coupled with high-performance liquid chromatography (HPLC)-UV detection was applied for the extraction and determination of bisphenol A (BPA) in water samples. An appropriate mixture of acetone (disperser solvent) and chloroform (extraction solvent) was injected rapidly into a water sample containing BPA. After extraction, sedimented phase was analyzed by HPLC-UV. Under the optimum conditions (extractant solvent: 142 μL of chloroform, disperser solvent: 2.0 mL of acetone, and without salt addition), the calibration graph was linear in the range of 0.5–100 μg L⁻¹ with the detection limit of 0.07 μg L⁻¹ for BPA. The relative standard deviation (RSD, n = 5) for the extraction and determination of 100 μg L⁻¹ of BPA in the aqueous samples was 6.0%. The results showed that DLLME is a very simple, rapid, sensitive and efficient analytical method for the determination of trace amount of BPA in water samples and suitable results were obtained.     

Development and application of a capillary electrophoresis based method for the simultaneous screening of six antibiotics in spiked milk samples

An easy to use and low time consuming capillary electrophoresis (CE) method was developed and applied to the simultaneous determination of six antibiotics (ampicillin, amoxicillin, cloxacillin, penicillin, tetracycline and chloramphenicol) in spiked milk samples. Samples of milk were cleaned up by solid-phase extraction (with a C₁₈ cartridge) after protein precipitation. Analysis was performed by CE and results compared with the obtained via HPLC, both coupled to a UV-vis detector (210 nm). CE employed a 58.5 cm long fused-silica capillary (50 cm to detector), 75 μm i.d., a 2.7 × 10⁻² M KH₂PO₄, 4.3 × 10⁻² M Na₂B₄O₇ separation buffer, pH 8; an applied voltage of 18 kV; a hydrostatic injection of 0.5 psi during 3 s; and a run temperature of 25 °C. Under the described conditions, amoxicillin was not separated by HPLC, while CE was able to separate, and, therefore, allow detection. Regardless of amoxicillin, comparable results were obtained by HPLC and CE. The average recoveries of antibiotics, from milk fortified at 2.5 and 5 μg/mL, was over 72% with R.S.D.s within 5%. Recovery levels were essentially dictated by the used SPE cartridge.     

Determination of phenylurea herbicides in aqueous samples using partitioned dispersive liquid-liquid microextraction

Partitioned dispersive liquid-liquid microextraction (PDLLME), using THF as the dispersive solvent and dichloromethane as the extraction solvent, was utilized to isolate and concentrate phenylurea herbicides (PUHs) from aqueous samples. In PDLLME, a dispersive solvent should be able to partition in the organic extractant droplets to effectively extract the polar organic compounds from aqueous samples. The mixture of the water-immiscible extractant and the partitioned dispersive solvent was obtained by centrifugation, dried under low pressure, reconstituted in methanol-water mixture (1:1), and injected into a HPLC system for the determination of PUHs. The enrichment factors of the PUHs ranged from 68 to 126 under the optimal conditions. The linear range was 0.5-100 ng ml⁻¹ for each analyte, the relative standard deviations of PUHs were in the range of 1.5-5.9% (n = 5), and the detection limits (signal-to-noise ratio of 3) ranged from 0.10 to 0.28 ng ml⁻¹ for the herbicides. The range of intraday precision (n = 5) for PUHs at the levels of 0.5, 5, and 50 ng ml⁻¹ were 3.0-5.9%, 1.8-3.3%, and 2.2-3.6%, respectively. The range of interday precision (n = 5) at 0.5, 5, and 50 ng ml⁻¹ were 0.4-1.8%, 1.2-2.4%, and 0.9-2.3%, respectively. The recoveries of PUHs from three spiked river water samples, at a level of 10 ng ml⁻¹, were 91.2-104.1%. Due to its rapidity, ease of operation, and high recovery, PDLLME can be utilized to isolate and concentrate organic environmental contaminants such as PUHs from aqueous samples.     

Dispersive liquid-liquid microextraction followed by high-performance liquid chromatography as an efficient and sensitive technique for simultaneous determination of chloramphenicol and thiamphenicol in honey

Dispersive liquid-liquid microextraction (DLLME) coupled with high-performance liquid chromatography-variable wavelength detector (HPLC-VWD) was developed for extraction and determination of chloramphenicol (CAP) and thiamphenicol (THA) in honey. In this extraction method, 1.0 mL of acetonitrile (as dispersive solvent) containing 30 μL 1,1,2,2-tetrachloroethane (as extraction solution) was rapidly injected by syringe into a 5.00-mL water sample containing the analytes, thereby forming a cloudy solution. After extraction, phase separation was performed by centrifugation and the enriched analytes in the sedimented phase were determined by HPLC-VWD. Some important parameters, such as the nature and volume of extraction solvent and dispersive solvent, extraction time, sample solution pH, sample volume and salt effect were investigated and optimized. Under the optimum extraction condition, the method yields a linear calibration curve in the concentration range from 3 to 2000 μg kg⁻¹ for target analytes. The enrichment factors for CAP and THA were 68.2 and 87.9, and the limits of detection (S/N = 3) were 0.6 and 0.1 μg kg⁻¹, respectively. The relative standard deviations (RSDs) for the extraction of 10 μg kg⁻¹ of CAP and THA were 4.3% and 6.2% (n = 6). The main advantages of DLLME-HPLC method are simplicity of operation, rapidity, low cost, high enrichment factor, high recovery, good repeatability and extraction solvent volume at microliter level. Honey samples were successfully analyzed using the proposed method.     

Isolation of tetracyclines in milk using a solid-phase extracting column and water eluent

An isolating method using a solid-phase extraction (SPE) ISOLUTE® C8 endcapped syringe-column for routine monitoring of residual tetracyclines (TCs) (oxytetracycline (OTC), tetracycline (TC), chlortetracycline (CTC), and doxycycline (DC)) in cow's milk is presented. In the simplest and most environmentally harmless method, milk samples could be applied directly to the SPE column, following which all TCs were eluted with water. No organic solvents were used at all. The purified sample was injected into a high-performance liquid chromatography (HPLC) with a photo-diode array detector (PDAD). For the HPLC determination/identification, a LiChrospher® 100 RP-8 endcapped column and a mobile phase of acetonitrile −7% (v v⁻¹) acetic acid solution (in water) (35:65, v v⁻¹) with a PDAD was used. The total time required for the analysis of one sample was <40 min. Average recoveries (spiked 0.1-1.0 μg ml⁻¹ each drug) and their standard deviations were >80 and <5%, respectively.