首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
分光光度法测定水溶液中的有机酸含量   总被引:7,自引:0,他引:7  
利用水溶液中的有机酸在高氯酸羟胺(HAP)和N,N′-二环己基碳酰亚胺(DCC)存在的条件下生成的羟肟酸,以及羟肟酸在酸性高氯酸铁溶液中显色的性质,建立了一种分光光度测定水中有机酸含量的方法。对显色剂的酸度、浓度、加入体积、HAP和DCC的浓度、加入体积以及显色反应的温度、反应时间对吸光度的影响进行了考察。结果表明,该显色反应在反应条件:0.0687mol/LHAP1.0mL、0.6mol/LDCC0.5mL、震荡均匀后室温下放置反应15min、0.02mol/L酸性高氯酸铁溶液(高氯酸浓度0.3mol/L)显色条件下具有最大的吸光度;并对正丁酸、正戊酸、苯甲酸进行了线性关系考察。结果表明,该检测方法具有仪器简单、操作方便、线性范围较宽、准确度高等优点,可用于那些不易从水溶液中萃取的有机酸的测定,也可用于液相色谱洗脱液中有机酸的测定。  相似文献   

2.
在十六烷基三甲基溴化铵(CTAB)存在下, 硝酸银与没食子酸丙酯在碱性介质中发生还原反应, 制得纳米银; 考察了反应时间、 氢氧化钠浓度、 反应温度以及PG/Ag+浓度比等条件对合成纳米银粒子的影响. 利用扫描电子显微镜对纳米银颗粒形貌和尺寸进行了表征, 结果表明获得了分散性良好的球形粒子. 实验中还发现在还原银离子制备纳米银过程中会产生强烈的表面等离子共振峰, 用紫外-可见光谱监测制备过程得到的纳米银紫外吸收带范围为400~450 nm, 最大吸收波长为420 nm, 光谱强度与抗氧化剂的浓度成正比. 将纳米银的这一特性用于定量测定没食子酸丙酯(PG)、 二丁基羟基甲苯(BHT)、 叔丁基对羟基茴香醚(BHA)和叔丁基对苯二酚(TBHQ)等抗氧化剂, 所得检出限分别为0.0752, 0.1242, 0.0693和0.0701 mg/L, 线性范围分别为0.2~1.8, 0.2~3.4, 0.2~3.4和0.2~3.0 mg/L.  相似文献   

3.
On heating with hydroxylamine and on subsequent treatment with ferric chloride, pyrrolidonecarboxylic acid gives a colour reaction. This reaction can be used for the quantitative estimation of glutamic acid in protein hydrolyzates since this acid is almost completely converted into pyrrohdonecarboxylic acid at 125° and pH 3–4.  相似文献   

4.
In methanol-water mixtures containing sodium or potassium hydroxide (up to 2.00M) the demethoxylation of 9-methoxyacridine to 9-acridone is of first order in both the free form of 9-methoxyacridine and the hydroxyl ion. The rate of the reaction is increased with an increase in the concentration of water. Sodium perchlorate has a small retarding effect on the reaction. In methanol-water mixtures containing perchloric or hydrochloric acid (up to 3.45M) the demethoxylation is of first order with respect to the protonated form of 9-methoxyacridine. The rate of the reaction decreases with an increase in the concentration of the acid or of sodium perchlorate, but when the concentration of water is increased (≈?1.7 to 50M) and that of the acid is not changed, it reaches a maximum value in mixtures containing 8 to 10M-water. The dechlorination of 9-chloroacridine to 9-methoxyacridine in methanol containing sodium hydroxide or methoxide (up to 0.31 M) is of first order in both the 9-chloroacridine and the hydroxyl or methoxyl ions.  相似文献   

5.
本文研究了Fe(Ⅲ)-铬天青S(CAS)-溴化十六烷基三甲铵(CTAB)体系显色反应的有机溶剂化效应.拟定了测定痕量铁的分光光度法.探讨了溶剂化效应机理.测定了络合物组成及溶剂化数.研究了有机溶剂对CAS离解常数(Ka3,Ka4)及Fe(Ⅲ)-CAS络合物稳定常数的影响.  相似文献   

6.
酵母核糖核酸的UV-Vis光谱探针反应的机理研究   总被引:6,自引:2,他引:6       下载免费PDF全文
采用UV-Vis分光光度法,研究在pH7-8的缓冲溶液中,酵母核糖核酸(RNA)与3-氨基-6-二甲氨基-2-甲基吩嗪盐酸盐(ZR)相互作用;反应生成红色配合物,该配合物的最大吸收波长为540nm;反应前后的吸收光谱变化明显,配合物的吸收峰与试剂本身比较红移90nm;研究了体系的酸度、温度、时间等基本反应条件以及不同类型的离子对体系的影响,发现离子强度的改变对体系的吸光度有明显的影响。  相似文献   

7.
Růzicka JA  Jakschová H  Mrklas L 《Talanta》1966,13(9):1341-1344
Fluorine is determined in the ash of bone or tooth tissue after the sample has been dissolved in dilute perchloric acid. Interfering phosphate is precipitated by the addition of silver perchlorate and sodium carbonate and then filtered off. The fluoride contained in the filtrate is determined spectrophotometrically, by the bleaching of the coloured complex of zirconium with Xylenol Orange. The reaction is carried out in dilute perchloric acid and allowed to proceed for 1 hr. The absorbance is measured at 540 mmu. The relationship between the absorbance and concentration is practically linear over the range 15-65 mug. The range can also be modified for 0-50 mug.  相似文献   

8.
《Analytical letters》2012,45(12):585-592
Abstract

The reaction of selected conjugated 3-ketosteroids with isonicotinic acid hydrazide (INH) reagent in methanol was investigated. The Δ1, 4?3-ketosteroids differed considerably from the Δ4 -3-ketosteroids with regard to the wavelength of maximum absorbance and to the reaction time and temperature required to attain maximum absorbance readings. Optimum conditions resulting in stable, maximum absorbance readings were determined experimentally for 17 standard compounds.  相似文献   

9.
In the present work the thermal stability of some members of the hydroxylamine family was studied using adiabatic calorimetry. The study included aqueous solutions of hydroxylamine free base, hydroxylamine hydrochloride, hydroxylamine sulfate, and hydroxylamine-o-sulfonic acid of concentrations typically used in industry. Also, the catalytic effect of metal surfaces of stainless steel, carbon steel, and titanium was studied. From the solutions studied HA is the most reactive with higher maximum temperature, pressure, non-condensable pressure, and lower time to maximum rate. HA maximum heat rate is at least ∼3 times higher than that of the other solutions studied, and the pressure generation rate is ∼13 times higher. All decompositions were catalyzed by stainless steel, but only HA was catalyzed significantly by titanium metal. Solid hydroxylamine hydrochloride, hydroxylamine sulfate, and hydroxylamine-o-sulfonic acid exhibited stability up to ∼60 °C. Hydroxylamine 100% was not studied because it is not readily available, is not used industrially, and is known to be unstable at room temperature. A violent reaction was measured for solid hydroxylamine sulfate that generated a heat rate >500 °C/min and pressure rate >5200 psia/min before the sample cell was completely destroyed by the generated pressure.  相似文献   

10.
《Analytical letters》2012,45(10):2035-2050
ABSTRACT

Naproxen reacts with 1-naphthylamine and sodium nitrite to give an orangish red colour having maximum absorbance at 460-480 nm (working wavelength 480 nm). The reaction is selective for naproxen with 0.001 mg/ml as visual limit of quantitation and provides a basis for a new spectrophotometric determination. The reaction obeys Beer's law from 0.01mg to 6.5 mg/10ml of naproxen and the relative standard deviation is 1.5%. The quantitative assessment of tolerable amount of other drugs is also studied.  相似文献   

11.
A novel and facile method of introducing 4-hydroxyl group into the aromatic ring of azabenzanthrone compounds was carried out by reacting azabenzanthrone compounds with hydrazine hydrate or hydroxylamine hydrochloride and sodium hydroxide in diethylene glycol(DEG) solvent.The mechanism of reaction may involve an amino intermediate and follow a hydroxyl substitution process.  相似文献   

12.
An effective procedure for decontamination of beta-lactam antibiotic residues or contaminants in the pharmaceutical manufacturing environment was investigated. Decontamination with solutions of hydrochloric acid, sodium hydroxide, hydrogen peroxide and hydroxylamine as agents for degradation was assessed. According to the results, the beta-lactam antibiotics were significantly degraded with sodium hydroxide and hydroxylamine. From the structural analysis of the degradation products of a cephem antibiotic, cefpodoxime proxetil, it was found that hydroxylamine degraded the beta-lactam structure under mild conditions, while sodium hydroxide did not. Therefore, hydroxylamine was considered an appropriate decontamination agent for beta-lactam antibiotics.  相似文献   

13.
Aluminum is the third most abundant metal in the Earth’s crust. Despite its ubiquitous nature it is present in small amount in living organisms. Aluminum toxicity has been implicated in the pathogenesis of renal distinct clinical syndromes, including progressive and fatal encephalopathy and bone diseases. In the present study, Al was selected for the analysis by complexometric method. This method was based on the formation of a red colored ternary complex by the reaction of Aluminum with Aluminon (Aurin tricarboxylic acid triammonium salt) in the presence of micellar medium. The ternary complex of Aluminum with the surfactant Triton X-100 shows a maximum absorbance at 530 nm wavelength at pH 4.0 while with the sodium dodecyl sulfate it shows a maximum absorbance at 525 nm and at pH 5.0. The reaction was proceeded by the variation in pH and concentrations of surfactants, aluminon, aluminum. Their effects on the reaction of aluminum with aluminon complex in micellar media were recorded by UV-visible spectrophotometer. The reaction was found to be extremely rapid at room temperature. The system obeys Lambert Beer’s law between 0.24 and 21.74 μg/mL concentrations with Triton X-100. The values of slope, intercept and correlation coefficients were 0.07, 0.348 and 0.989, respectively. The concentration varied between 0.24 and 24.14 μg/mL with sodium dodecyl sulfate and the values of slope, intercept and correlation coefficients were 0.029, 0.148 and 0.962, respectively. The foreign ion effect was also tested by keeping the constant concentration of metal ion and determining its concentration in the presence of different foreign ions. The method was also applied for the determination of Al(III) in pharmaceutical formulations and water samples, which showed an excellent resemblance between reported and obtained results.  相似文献   

14.
检测土壤中全碘的硫氰酸铁-亚硝酸钠-碘催化比色法   总被引:3,自引:0,他引:3  
在稀硝酸溶液中 ,硫氰酸铁的褪色反应与体系中碘的含量、体系温度和反应时间有关 ,硫氰酸铁的质量浓度随时间的变化而减小 ,给检测带来较大误差。作者在体系反应一定时间之后加入颜色固定剂 ,使体系的吸光度在数小时内保持不变 ,提高了检测的准确度。  相似文献   

15.
用亚硝基铁氰化钠分光光度法测定药品“必理通”中的对乙酰氨基酚含量。采用亚硝基铁氰化钠试液为显色剂,蒸馏水做溶剂,在波长为700nm下有最大吸收,利用分光光度计测定不同浓度溶液的吸光度,并绘制标准曲线进行分析。实验证明,对乙酰氨基酚在0.024mg/mL~0.168mg/mL浓度范围内,吸光度与样品浓度的线性关系良好,回收率在98.0%以上。此测定方法准确、快速、简便,是测定对乙酰氨基酚含量的最佳方法之一。  相似文献   

16.
A highly sensitive and simple method, based on hydride generation and atomic fluorescence detection, has been developed for the determination of As, Bi, Sb, Se(IV) and Te(IV) in aqua regia extracts from atmospheric particulate matter samples. Atmospheric particulates matter was collected on glass fiber filters using a medium volume sampler (PM1 particulate matter). Two-level factorial designs have been used to optimise the hydride generation atomic fluorescence spectrometry (HG-AFS) procedure. The effects of several parameters affecting the hydride generation efficiency (hydrochloric acid, sodium tetrahydroborate and potassium iodide concentrations and flow rates) have been evaluated using a Plackett-Burman experimental design. In addition, parameters affecting the hydride measurement (delay, analysis and memory times) have been also investigated. The significant parameters obtained (sodium tetrahydroborate concentration, sodium tetrahydroborate flow rate and analysis time for As; hydrochloric acid concentration and sodium tetrahydroborate flow rate for Se(IV); and sodium tetrahydroborate concentration and sodium tetrahydroborate flow rate for Te(IV)) have been optimized by using 2n + star central composite design. Hydrochloric acid concentration and sodium tetrahydroborate flow rate were the significant parameters obtained for Sb and Bi determination, respectively. Using a univariate approach these parameters were optimized. The accuracy of methods have been verified by using several certified reference materials: SRM 1648 (urban particulate matter) and SRM 1649a (urban dust). Detection limits in the range of 6 × 10−3 to 0.2 ng m−3 have been achieved. The developed methods were applied to several atmospheric particulate matter samples corresponding to A Coruña city (NW Spain).  相似文献   

17.
采用碱熔样硅钼蓝分光光度法测定铜精矿中二氧化硅的含量。讨论了熔融条件、吸收波长、溶液酸度、水浴加热时间、显色时间以及共存离子干扰等条件对测定结果的影响。确定以氢氧化钠为熔剂,在680℃熔融15 min,熔样效果最佳;根据样品中二氧化硅的含量选择波长,当二氧化硅含量小于1%时,选用810 nm为分析波长,二氧化硅含量为1%~15%时,选用650 nm为分析波长;在酸度为0.15~0.20 mol/L盐酸溶液中,水浴加热60 s,显色15min,显色效果为最佳。使用硫酸亚铁铵作为还原剂。方法的加标回收率在94.8%~98.8%之间,5个样品独立测定结果的相对标准偏差为0.26%~4.48%(n=11),标准样品测定结果与标准值吻合。该方法简单、快速、准确,适用于铜精矿中二氧化硅含量的测定。  相似文献   

18.
Sahu P  Panda JD  Sinha BC 《Talanta》1992,39(5):541-545
A critical study has been made of the effect of acid concentration and of polymerized and depolymerized zirconyl ions on the formation of ZrO-XO complexes and their stabilities. At an optimum acidity of 0.5-0.6M hydrochloric acid, most of the common cations occurring in silicates do not interfere. Maximum colour development is almost instantaneous for the depolymerized ZrO-XO complex, but takes a few hours for the polymerized complex; the colour is stable for several hours. The absorbance is highest for the depolymerized ZrO-XO complex and decreases with an increase in polymerization of the zirconyl ions. Dissolved oxides of nitrogen affect the stability of the ZrO-XO complex but can be eliminated with urea. A simple, rapid and sensitive spectrophotometric method has been worked out for use of this complex in determination of fluoride in silicates, without separation, after fusion of the sample with sodium hydroxide at 450-550 degrees.  相似文献   

19.
Sodium citrate and sodium potassium tartrate are assayed by passing aqueous solutions of the salts through cation exchange resin columns, concentrating the effluents from the columns, and then titrating the effluents with standard sodium hydroxide solution. Sodium citrate is assayed by titrating a solution of the salt in glacial acetic acid with standard acetous perchloric acid, the end-point being detected potentiometrically; sodium potassium tartrate is assayed by stirring the salt in excess standard acetous perchloric acid, and then backtitrating the excess acetous perchloric acid with standard acetous potassium acetate, the end-point being detected potentiometrically.  相似文献   

20.
 A sensitive spectrophotometric method for the determination of ethanol with potassium dichromate was developed. Chromium(VI), in 7 mol L-1 perchloric acid, reacts quantitatively with ethanol to form chromium(III) and acetic acid. The reaction is complete in about 15 min at room temperature and the chromium(VI) consumed may be determined by the decrease of the absorbance at 267 nm. The analytical working parameters (such as acidity and ionic strength of the solution, temperature and time of the reaction, chromium(VI) concentration, matrix interferences) were optimized. The apparent molar absorptivities of chromium(VI), in the monomer and dimer form, and the equilibrium quotient for the dimerization reaction were determined in 3 mol L-1 perchloric acid solution. The method was applied to the analysis of micro samples of commercial beverages (beers, wines and spirits) without the previous distillation of ethanol. Received: 9 April 1996/Revised: 3 June 1996/Accepted: 11 June 1996  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号