Pentacene precursors for solution-processed OFETs

15-Acetoxy- and 15-hydroxy-6,13-dihydro-6,13-ethanopentacenes sublimed over 300 °C and no pentacene was formed below the temperature. The precursors bearing chlorinated epithiomethano bridges suffered complicated decomposition to give oligomeric pentacene derivatives. The precursor bearing an epithio-oxomethano bridge underwent smooth and clean conversion to pentacene by heat or light. An organic field-effect transistor fabricated by the spin-coating method of the precursor followed by light irradiation at 120 °C showed a good FET performance of μ=2.5×10⁻² cm² V⁻¹ s⁻¹ and on/off ratio=3.8×10⁴.     

Ab initio investigation of O3 addition to double bonds of limonene

The reaction of the O₃ addition to double bonds of the limonene in the gas phase has been investigated using ab initio methods. Four different possibilities for the O₃ addition to the double bonds, which correspond to the two C–C double bonds (endocyclic or exocyclic), and two different orientations of each C–C double bonds, have been considered. The corresponding rate constants have been calculated using the transition-state theory (TST) at the CCSD(T)/6-31G(d) + CF//B3LYP/6-311+G(d,p) level of theory. The high-pressure limit of the overall rate constant at 298 K is found to be ∼2.92 × 10⁻¹⁶ cm³ molecule⁻¹ s⁻¹ that is in a good agreement with the experimental data, and the rate constants of the four individual reaction channels turn out to be 2.1 × 10⁻¹⁶ cm³ molecule⁻¹ s⁻¹, 1.2 × 10⁻¹⁷ cm³ molecule⁻¹ s⁻¹, 6.5 × 10⁻¹⁷ cm³ molecule⁻¹ s⁻¹ and 5.1 × 10⁻¹⁸ cm³ molecule⁻¹ s⁻¹ for 1-endo, 2-endo, 1-exo and 2-exo, respectively.     

Accessing DNA by low voltage alternating current Joule effect heating

A DNA release sample preparation method based on the use of low voltage alternating currents (LVACs) to generate Joule effect heating (JEH) is reported. This is a simple cell disruption strategy that offers internal, homogenous, rapid and low power consumption heating for the access of analytical grade DNA in seconds.A 100 μL JEH microreactor with a parallel and symmetric two electrode arrangement for uniform field generation was fabricated by machining and used to characterise JEH and DNA release from human epithelia, yeast (Saccharomyces cerevisiae) and Gram-positive bacteria (Enterococcus faecium) cell types. A 1 kHz sinusoidal low voltage (e.g. 10 Vrms) alternating current was used to reduce electrode:sample interactions. Following 96 °C JEH treatment, effective DNA release was identified by PicoGreen^® quantification for all three cell types. The JEH treated sample material was further successfully used, without purification, as a PCR template. Exposure to JEH-mediated 96 °C temperatures for a 1 s duration was used to provide PCR-grade DNA template material from S. cerevisiae and E. faecium cells, and a 10 s duration was used for human epithelia cells. However, prolonged (>1 min) exposure to 96 °C JEH-mediated temperatures resulted in diminished DNA returns and the production of components that interfered with the PCR reaction.Further miniaturisation of the LVAC JEH cell by microfabrication was considered, and a JEH microreactor designs were evaluated by FLOTHERM v3.2 thermal modelling. Thermal isolation, using a free-standing cavity structure was identified as an excellent means to enable rapid heating (220 °C s⁻¹) with low power consumption (0.2 W).     

Determination of SCFAs in water using GC-FID. Selection of the separation system

In the present study, an analytical procedure was developed for the determination of short-chain fatty acids (SCFAs) in landfill leachate and municipal wastewater employing injection of aqueous samples to gas chromatograph with flame ionization detector (GC-FID). Chromatographic conditions such as a separation system, injection volume, oven temperature program were investigated and selected. With two columns, one with a polar (polyethylene glycol) and one with a non-polar (dimethylpolisiloxane) stationary phase, good separation of SCFAs, containing from 2 to 8 carbon atoms, was achieved. The sample volume was 2 μL and the temperature program 80 °C (30 s) then 7 °C min⁻¹ to 220 °C (2 min). LOQs values were below 0.25 mg L⁻¹. The concentrations of the acids in the landfill leachate studied ranged from 0.45 ± 0,059 (average ± extended uncertainty) mg L⁻¹ for pentanoic acid to 15.2 ± 0.73 mg L⁻¹ for ethanoic acid. Concentrations of SCFAs in the municipal wastewater were lower than LOQs.     

Preparation of higher flux NaA zeolite membrane on asymmetric porous support and permeation behavior at higher temperatures up to 145 °C in vapor permeation

NaA zeolite membranes were synthesized on an asymmetric porous alumina support with a lower mass-flow resistance for development of more economically feasible membranes with higher permeation performance. The support influence on permeation fluxes through the membrane using asymmetric support was investigated by vapor permeation at 100–145 °C in a mixture of water (10 wt.%)/ethanol (90 wt.%) in which the higher permeation fluxes up to 37 kg m⁻² h⁻¹ or water permeances up to 3.2 × 10⁻⁶ mol m⁻² s⁻¹ Pa⁻¹at 145 °C were observed. The performance was higher than those in the previously reported NaA membrane on a monolayer porous alumina support of 31 kg m⁻² h⁻¹ or water permeances of 2.5 × 10⁻⁶ mol m⁻² s⁻¹ Pa⁻¹at 145 °C. These results are experimental evidence to show the effect of asymmetric support utilization in membrane preparation on the higher membrane performance. The estimate of the pressure drop over the both types of support indicates that the improvement of higher permeation fluxes in the asymmetric type membrane could be attributed to the suppression of pressure drop in the support layer due to lower mass-flow resistance there.     

Self-standing single lithium ion conductor polymer network with pendant trifluoromethanesulfonylimide groups: Li diffusion coefficients from PFGSTE NMR

Solid electrolyte materials have the potential to improve performance and safety characteristics of batteries by replacing conventional solvent-based electrolytes. For this purpose, new candidate single ion conductor self-standing networks were synthesized with trifluoromethane-sulfonylimide (TFSI) lithium salt based monomer using poly(ethyleneglycol) dimethacrylate (PEGDM 750) as crosslinker. The highest ionic conductivity was 3.4 × 10⁻⁷ S cm⁻¹ at 30 °C in the dry state. Thermal and mechanical analyses showed good thermal stability up to 190 °C and rubbery-like properties at ambient temperature. A direct relationship between ionic conductivity and glassy or rubbery state of the membranes was found. Vogel–Tammann–Fulcher behavior was observed in the dry state which is consistent with a lithium conductivity correlated with polymer chain mobility. By swelling the network in propylene carbonate, a self-standing electrolyte gel could be obtained with an ionic conductivity as high as 1 × 10⁻⁴ S cm⁻¹ at 30 °C. The individual diffusion coefficients of mobile species in the material (¹⁹F and ⁷Li) were measured and quantified using pulsed-field gradient nuclear magnetic resonance (PFG-NMR). Diffusion coefficients for the most mobile components of the lithium cations and fluorinated anions at 100 °C in dry membranes have been found to be 3.4 × 10⁻⁸ cm² s⁻¹ and 2.1 × 10⁻⁸ cm² s⁻¹ respectively.     

Sequential injection methodology for carbon speciation in bathing waters

A sequential injection method (SIA) for carbon speciation in inland bathing waters was developed comprising, in a single manifold, the determination of dissolved inorganic carbon (DIC), free dissolved carbon dioxide (CO₂), total carbon (TC), dissolved organic carbon and alkalinity. The determination of DIC, CO₂ and TC was based on colour change of bromothymol blue (660 nm) after CO₂ diffusion through a hydrophobic membrane placed in a gas diffusion unit (GDU). For the DIC determination, an in-line acidification prior to the GDU was performed and, for the TC determination, an in-line UV photo-oxidation of the sample prior to GDU ensured the conversion of all carbon forms into CO₂. Dissolved organic carbon (DOC) was determined by subtracting the obtained DIC value from the TC obtained value. The determination of alkalinity was based on the spectrophotometric measurement of bromocresol green colour change (611 nm) after reaction with acetic acid. The developed SIA method enabled the determination of DIC (0.24–3.5 mg C L⁻¹), CO₂ (1.0–10 mg C L⁻¹), TC (0.50–4.0 mg C L⁻¹) and alkalinity (1.2–4.7 mg C L⁻¹ and 4.7–19 mg C L⁻¹) with limits of detection of: 9.5 μg C L⁻¹, 20 μg C L⁻¹, 0.21 mg C L⁻¹, 0.32 mg C L⁻¹, respectively. The SIA system was effectively applied to inland bathing waters and the results showed good agreement with reference procedures.     

Optimization of direct whole blood PCR amplification with applications on a static thermostat chip

In this paper, direct whole blood PCR amplifications on a static chip thermostat without sample purifications are demonstrated; in these amplifications, problems such as cross-interferences and contaminations could be avoided. The amplification conditions, such as the compositions of reagents and thermal programs, were investigated systematically by a GeneAmp PCR system with a native p53 gene segment (about543 bp) of human genome and an exterior lambda DNA segment (about 500 bp) as targets. Direct amplifications of p53 and K-ras (about 157 bp) gene segments from 0.5 μL blood samples were successfully demonstrated by a static PCR chip with an indium tin oxide glass substrate. The chip thermostat has a typical size of 25 mm × 25 mm, and a polyethylene tube was used as the PCR vial on the glass surface of the chip. Fuzzy proportional integration–differentiation algorithms were adopted in temperature controls of the chip with an aid of a micro-Pt100 sensor. In the direct PCR with the thermostat chip, the whole process only involves automatic thermal programs. This work demonstrated that a chip PCR for field test without desktop facilities is possible either for a point of care test or for forensic analysis. Figure Photo of the glass static thermostat chip with 2 PCR reaction vials Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

A gravity driven micro flow injection wetting film extraction system on a polycarbonate chip

A micro flow injection wetting film liquid-liquid extraction system has been developed for trace analyte concentration and on-chip detection. A hydrophobic channel fabricated on a polycarbonate chip was used to support the wetting film, and hydrostatic pressure generated by the difference in liquid levels was employed to drive the fluids. Sequential injection of segments of aqueous sample solution and organic solvent was conducted by switching the sample- or solvent-containing vials to an on-chip sampling probe, and detection was performed by a co-focused, laser induced fluorescence detector. Using butyl rhodamine B as a model analyte and butanol as the solvent for both film-coating and elution, various experimental conditions such as hydrostatic pressure, coating time, channel length, sampling volume, and sample acidity were investigated. Under optimized conditions, a 24-fold enrichment factor was obtained with the consumption of about 3 μL sample solution, and a detection limit (3σ) of 6.0 × 10⁻⁹ M butyl rhodamine B was achieved at the sampling rate of 19 h⁻¹. Eleven consecutive runs of a 1.0 × 10⁻⁵ M butyl rhodamine B solution produced a relative standard deviation of 1.5% for the detected fluorescence signals.     

A new micro-fluid chip calorimeter for biochemical applications

Based on a new thermopile heat power sensor, which was developed in MEMS technology, a miniaturized flow-through calorimeter was constructed. The heat power sensor consists of a silicon chip with a thin film BiSb/Sb thermopile and a PMMA reaction chamber. To ensure high signal resolution the heat power sensor is mounted inside a high-precision thermostat, which has a temperature stability of less than 100 μK. The heat power sensitivity of the calorimeter is 4-7 V W⁻¹ depending on the thermal conductivity of the liquid, the height of the chosen reaction chamber and the volume flow rate. A limit of detection of less than 50 nW can be obtained for volume flows lower than 5 μl min⁻¹. An important advantage is the low sample consumption of the calorimeter. For special applications the sample need for one measurement pulse does not exceed 20 μl.     

Screening of transformation products in soils contaminated with unsymmetrical dimethylhydrazine using headspace SPME and GC-MS

The paper describes a novel SPME-based approach for sampling and analysis of transformation products of highly reactive and toxic unsymmetrical dimethylhydrazine (UDMH) which is used as a fuel in many Russian, European, Indian, and Chinese heavy cargo carrier rockets. The effects of several parameters were studied to optimize analyte recovery. It was found that the 85 μm Carboxen/polydimethylsiloxane fiber coating provides the highest selectivity for selected UDMH transformation products. Optimal sampling/sample preparation parameters were determined to be 1-h soil headspace sampling time at 40 °C. The GC inlet temperature was optimized to 170 °C held for 0.1 min, then 1 °C s⁻¹ ramp to 250 °C where it was held for 40 min. Temperature programing resulted in a fast desorption along with minimal chemical transformation in the GC inlet. SPME was very effective extracting UDMH transformation products from soil samples contaminated with rocket fuel. The use of SPME resulted in high sensitivity, speed, small labor consumption due to an automation and simplicity of use. It was shown that water addition to soil leads to a significant decrease of recovery of almost all target transformation products of UDMH. The use of SPME for sampling and sample preparation resulted in detection of the total of 21 new compounds that are relevant to the UDMH transformation in soils. In addition, the number of confirmed transformation products of UDMH increased from 15 to 27. This sampling/sample preparation approach can be recommended for environmental assessment of soil samples from areas affected by space rocket activity.     

Enthalpy change and mechanism of oxidation of o-phenylenediamine by hydrogen peroxide catalyzed by horseradish peroxidase

The hydrogen peroxide-oxidation of o-phenylenediamine (OPD) catalyzed by horseradish peroxidase (HRP) at 37 °C in 50 mM phosphate buffer (pH 7.0) was studied by calorimetry. The apparent molar reaction enthalpy with respect to OPD and hydrogen peroxide were −447 ± 8 kJ mol⁻¹ and −298 ± 9 kJ mol⁻¹, respectively. Oxidation of OPD by H₂O₂ catalyzed by HRP (1.25 nM) at pH 7.0 and 37 °C follows a ping-pong mechanism. The maximum rate V_max (0.91 ± 0.05 μM s⁻¹), Michaelis constant for OPD K_m,S (51 ± 3 μM), Michaelis constant for hydrogen peroxide Km,H₂O₂ (136 ± 8 μM), the catalytic constant k_cat (364 ± 18 s⁻¹) and the second-order rate constants k₊₁ = (2.7 ± 0.3) × 10⁶ M⁻¹ s⁻¹ and k₊₅ = (7.1 ± 0.8) × 10⁶ M⁻¹ s⁻¹ were obtained by the initial rate method.     

Thin Pd–23%Ag/stainless steel composite membranes: Long-term stability,life-time estimation and post-process characterisation

The long-term stability of Pd–23%Ag/stainless steel composite membranes has been examined in H₂/N₂ mixtures as a function of both temperature and feed pressure. During continuous operation, the membrane shows a good stability at 400 °C while the N₂ leakage increases very slowly at a temperature of 450 °C (P_feed = 10 bar). After 100 days of operation (P_feed = 5–20 bar, T = 350–450 °C), the N₂ permeance equals 7.0 × 10⁻⁹ mol m⁻² s⁻¹ Pa⁻¹, which indicates that the H₂/N₂ permselectivity still lies around 500, based on a H₂ permeance equal to 3.0 × 10⁻⁶ mol m⁻² s⁻¹ Pa⁻¹. Despite the generation of small pinholes, a membrane life-time of several (2–3) years (T ≤ 425 °C) is estimated for the experimental conditions employed based on long-term stability tests over 100 days. Post-process characterisation shows a considerable grain growth and micro-strain relaxation in the Pd–23%Ag membrane after the prolonged permeation experiment. Changes in surface area are relatively small. In addition, segregation of Ag to the membrane surfaces is observed. The formation of pinholes is identified as the main source for the increased N₂ leakage during testing at higher temperature.     

Application of a polysiloxane-based extraction method combined with column liquid chromatography to determine polycyclic aromatic hydrocarbons in environmental samples

Silicone rods with a diameter of 1 mm and 10 mm long were used to extract polycyclic aromatic hydrocarbons (PAHs) from water samples and for the rapid screening of highly contaminated waste material. The rods were placed in a 15 ml glass vial for the extraction of the analytes, which involved shaking (300 min⁻¹) the sample for 3 h. After extraction the rods were placed into 250 μl inserts of 2 ml vials filled with 100 μl of an acetonitrile-water mixture (4:1) and desorption was performed with sonication for 10 min. Then the PAHs were determined using LC and fluorescence detection. Recoveries of the rod extraction ranged between 62 and 97% and the detection limits were between 0.1 and 1.2 ng l⁻¹. These results are comparable with those of stir bar sorptive extraction (SBSE). Although the rods are reusable, their low price means they can be discarded if contaminated, eliminating the need for expensive cleaning. One disadvantage compared to SBSE is the longer extraction time needed to reach equilibrium.     

Thermal diffusivity measurement of low-k dielectric thin film by temperature wave analysis

Thermal diffusivity of thin film with low dielectric constant (k), what is called low-k dielectric thin film, 0.31-1.14 μm, including hydrogen-silsesquioxane (HSQ), methyl-silsesquioxane (MSQ), and poly(arylen ether) was examined by temperature wave analysis. The phase shift of temperature wave was observable up to 100 kHz. Thermal diffusivity of HSQ was 4.7 × 10⁻⁷ m² s⁻¹, on the other hand it was not higher than 1.1 × 10⁻⁷ m² s⁻¹ for MSQ or poly(arylen ether) at room temperature. Temperature dependence of thermal diffusivity/thermal conductivity of MSQ was obtained, thermal diffusivity decreased but thermal conductivity increased in a heating scan at 30-150 °C. It was shown that the thermal diffusivity of low-k thin film was correlated with the chemical and the physical structures, the latter was formed in the spin-coating and the curing process.     

Oxidation of substituted pyridines by dimethyldioxirane: kinetics and solvent effects

The oxidation of a series of substituted pyridines by dimethyldioxirane (1) produced the expected N-oxides in quantitative yields. The second order rate constants (k₂) for the oxidation of a series of substituted pyridines (2a-g) by dimethyldioxirane were determined in dried acetone at 23 °C. An excellent correlation with Hammett sigma values was found (ρ = −2.91, r = 0.995). Kinetic studies for the oxidation of 4-trifluoromethylpyridine by 1 were carried out in the following dried solvent systems: acetone (k₂ = 0.017 M⁻¹ s⁻¹), carbon tetrachloride/acetone (7:3; k₂ = 0.014 M⁻¹ s⁻¹), acetonitrile/acetone (7:3; k₂ = 0.047 M⁻¹ s⁻¹), and methanol/acetone (7:3; k₂ = 0.68 M⁻¹ s⁻¹). Kinetic studies of the oxidation of pyridine by 1 versus mole fraction of water in acetone [k₂ = 0.78 M⁻¹ s⁻¹ (χ = 0) to k₂ = 11.1 M⁻¹ s⁻¹ (χ = 0.52)] were carried out. The results showed the reaction to be very sensitive to protic, polar solvents.     

Investigation of homopolymerization rate of perfluoro-4,5-substituted-2-methylene-1,3-dioxolane derivatives and properties of the polymers

Five perfluoro-4,5-substituted-2-methylene-1,3-dioxolane monomers were synthesized. These monomers were found to readily polymerized by a free radical initiator in bulk and/or in solutions. Homopolymerization rates were determined using in situ ¹⁹F NMR measurements and found to be 0.25 to 1.66 × 10⁻⁴ mol L⁻¹ s⁻¹ in 1,1,2-trichlorotrifluoroethane at 41 °C using the perfluorodibenzoyl peroxide as an initiator. The rates depend on the substituents on the 4 and 5 positions of the dioxolane. The purified polymers were thermally stable (up to 350 °C). They show low refractive indexes (1.33-1.36 at 532 nm). They are transparent from UV to near IR region and have high glass transition temperatures (100-170 °C).     

Kinetics study of the SO2 sorption by Brazilian dolomite using thermogravimetry

Sulfur emission in coal power generation is a matter of great environmental concern. Limestone sorbents are widely used for reducing such emissions. This work applies thermogravimetry to determine apparent activation energy and frequency factor on the sorption of SO₂ by limestone. The kinetic parameters were determined from Arrhenius plots generated from TG/DTG measurements. The experiments were carried out under isothermal conditions between 600 and 900 °C. A natural dolomite with a mean size of 650 μm was used. The Arrhenius plot shows that there is a clear change on reaction mechanism in the range of temperatures between 800 and 875 °C. Supposedly, beyond 850 °C sintering comes to increasingly restrain reaction. For temperatures up to 850 °C the frequency factor and the apparent activation energy resulted, respectively, 1.410 s⁻¹ and 8.8 kJ mol⁻¹.