染料敏化太阳电池用聚合物电解质

综述了本研究小组近年来用于染料敏化太阳电池中聚合物电解质的研究概况.设计合成了几类性能优良的聚合物电解质,较好地改进了液体电解质染料敏化太阳电池(DSSC)的使用稳定性,研究结果具有实际应用的价值,并提出了此领域研究今后的发展方向.     

聚(4-乙烯基吡啶)的合成及其在染料敏化太阳电池中的应用

采用自由基聚合法合成了聚(4-乙烯基吡啶)(P4VP),并用于制备染料敏化太阳电池的凝胶电介质.研究了P4VP含量对电解质和太阳电池性能的影响.结果表明,以P4VP为骨架通过化学交联固化液态电解质制备的有机胶体电解质体系有机相可溶剂化Li ,当其含量为7.5wt%时体系离子电导率可达5.77mS/cm与液态电解质相当.利用这种准固态电解质制备的敏化太阳电池在100mW/cm2,25℃下获得光电转换效率2.3%.     

电泳法制备具有{001}面TiO2纳米片分级球散射层的染敏太阳电池光电极

利用简便的溶剂热法,制得了由锐钛矿相的纳米片组成的、{001}面接近100%暴露的TiO2分级球形结构。利用电泳沉积法,将所得的TiO2分级球形结构作为散射层引入到染料敏化太阳电池(DSSC)中,并很好地保护了这种脆弱的分级结构。由于这种分级球形结构比TiO2纳米颗粒具有更好的染料吸附性能和光散射性能,使用这种TiO2分级球形结构作为散射层的DSSC达到了7.38%的光电转换效率,较之基于TiO2纳米颗粒的DSSC有了26%的提高。     

染料敏化纳米薄膜太阳电池电解质的优化

探讨了小面积染料敏化纳米薄膜太阳电池放大到大面积太阳电池组件时,各种电解质体系对电池性能的影响,综合优化了各种电解质的性能,同时与大面积电池(0.8cm×18cm)制作相结合,获得符合电池各种性能要求的最佳配比的电解质体系.光电转换效率可达到6.48%.     

添加剂对染料敏化太阳电池电解质性能的影响

以N-甲基咪唑、苯并咪唑、叔丁基吡啶和离子液体1-甲基-3-乙基咪唑三氟乙酸盐(EMITA)作为染料敏化太阳电池(DSCs)电解质溶液中的添加剂, 使用超微电极通过循环伏安法研究其对液体电解质中I-3和I-氧化还原行为的影响, 通过电化学阻抗谱研究了上述四种添加剂对Pt电极电解质界面的影响. 结果表明, 添加剂EMITA的加入使I-3在电解质中的扩散系数减小, Pt电极电解质界面上的界面传输电阻Rct增大, 电解质的电阻降低; 光伏性能测试表明, EMITA的添加提高了DSCs的开路电压和填充因子, 其DSCs的光电转换效率达到了5.72%.     

染料敏化太阳电池中TiO2/染料/电解质界面的修饰

染料敏化太阳电池(DSC)作为新型太阳电池自问世以来受到了广泛关注, 其系统内部的接触界面尤其是TiO₂/染料/电解质界面一直是该领域的研究热点. 光敏染料的吸附以及电子的注入、传输和复合都发生在该界面, 其界面性质对DSC性能具有很大影响. 对染料敏化太阳电池中TiO₂/染料/电解质界面进行修饰可以有效抑制染料聚集和电子复合, 提高电子的注入效率与传输速率; 同时, 对TiO₂导带边的位置及染料吸附等也产生一定的影响, 最终提高电池的光电转换效率和稳定性. 本文主要从不同的修饰途径详细评述了TiO₂/染料/电解质界面修饰方法及机理研究进展,包括TiO₂光阳极的修饰改性、染料溶液中共吸附剂的引入和多种染料共敏化处理以及电解质中不同功能添加剂的应用. 指出了这些修饰方法目前存在的主要问题, 并对未来的发展方向进行了展望.     

纳米氧化镍浓度对磁性准固态染料敏化太阳能电池的影响

以琼脂糖为聚合物基质,N-甲基-2-吡咯烷酮(NMP)为溶剂,磁性纳米氧化镍颗粒作为添加剂用于制备染料敏化太阳能电池(DSSC)的磁性聚合物电解质。通过SEM与离子电导率测试研究不同纳米氧化镍掺杂浓度对磁性聚合物电解质的影响,并对相应的染料敏化太阳能电池进行光电性能测试与电化学交流组抗谱(EIS)测试,结果表明:1.0wt%的纳米氧化镍掺杂浓度为最优掺杂浓度,在此浓度下聚合物电解质的表面形貌较为平整,同时电解质具备最高离子电导率(2.43×10-3S.cm-1);染料敏化太阳能电池的光电效率与电子寿命均随着纳米氧化镍掺杂浓度的增加而先增加后降低,并都在纳米氧化镍掺杂浓度为1.0wt%达到最大,此时电池的光电效率为1.63%、开路电压为0.57 V、短路电流密度为5.8 mA.cm-2、填充因子为0.53。     

改进型溶胶-凝胶法制备粒径可调高染料吸附量TiO2微球及其在染敏电池光散射层中的应用

利用改进型的溶胶-凝胶法,制得了由锐钛矿相纳米颗粒组成的TiO2多孔微纳小球。通过调节前驱物浓度,合成出粒径可控的尺寸分别为100,175,225,475 nm的TiO2微纳小球,并通过电泳沉积法将合成出的小球作为光散射层引入到染料敏化太阳电池(DSSC)中。由于这种微纳小球在具备良好的光散射性能的同时也具备较高的染料吸附量,因此相较于基于纳米颗粒的单层结构的DSSC拥有更高的光电转换效率。通过比较分析,粒径尺寸为475 nm的微球作为光散射层的DSSC光电转换效率可以达到6.3%,较之于基于纳米颗粒的DSSC提高了30%。     

聚合物电解质在染料敏化太阳能电池中的应用进展

染料敏化太阳能电池(DSSC)由于成本低、污染小、制备工艺简单而受到广泛关注。电解质在其中起到桥梁的作用,能促使染料再生、输运空穴,从而完成整个光电循环过程,是DSSC重要的组成部分。本文简要介绍了DSSC的基本结构和工作原理,指出了传统液态电解质存在的问题,综述了近年来以聚合物为基体制备的新型固态聚合物电解质、凝胶聚合物电解质以及多孔聚合物电解质在DSSC中的应用,最后对聚合物电解质在染料敏化太阳能电池中的发展做出了展望。     

双层分等级TiO_2纳米线制备及其光伏性能研究

采用两步溶剂热反应制备了底层为分等级锐钛矿的TiO_2纳米线阵列,上层为分等级锐钛矿的TiO_2纳米线薄膜的双层结构电极.通过XRD和SEM对其组成和形貌进行了表征,并考察了纳米线薄膜对染料敏化太阳电池(DSSC)光伏性能的影响.实验结果表明,分等级锐钛矿的TiO_2纳米线作为DSSC的光阳极,光电转换效率为4.39%,其效率高于光滑的TiO_2纳米线光阳极电池效率(2.07%).     

A highly efficient electric additive for enhancing photovoltaic performance of dye-sensitized solar cells

N-cetylpyridinium iodide (N-CPI) as a new electric additive for enhancing photovoltaic performance of the dye-sensitized solar cell (DSSC) was studied. It showed high efficiency for enhancing both the open-circuit voltage and the short-circuit current density of DSSC when the suitable amount of N-CPI as 0.02 M was added in liquid electrolyte. The energy conversion efficiency of DSSC increased from 4.429% to 6.535%, with 47.55% enhancement. Therefore, it is a highly efficient electric additive for DSSC. The intrinsic reason is owing to the special molecular structure of N-CPI, which contains two different polarity groups. As a surfactant, N-CPI could form ordered arrangement in liquid electrolyte, which affects the diffusing ability and the redox reaction of I^?/I ₃ ^? , and further affects the photovoltaic performance of DSSC.     

Synthesis of organic sulfobetaine‐based polymer gel electrolyte for dye‐sensitized solar cell application

We have synthesized eco‐friendly, economic, and equally efficient polysulfobetaine‐based gel electrolyte to the alternative of liquid electrolyte in the fabrication of dye‐sensitized solar cells (DSSCs) for the first time. This nitrogen‐rich and highly conductive polysulfobetaine was synthesized by an easy and facile method without the use of any catalyst and explored for its DSSC application. The synthesized polymer gel electrolyte exhibited good ionic conductivity about 6.8 × 10^?3 Scm^?1 at ambient temperatures. DSSCs were fabricated based on this polysulfobetaine gel electrolyte and studied for their performance based on photovoltaic parameters. The DSSC photovoltaic results were appreciable and are Voc = 0.82 V, Jsc = 11.49 mA/cm², FF = 66%, and PCE = 6.26% at 1 sun intensity. These values are slightly lower than conventional liquid electrolyte‐based DSSC shown as Voc = 0.78 V, Jsc = 12.90 mA/cm², FF = 69%, and PCE = 7.07%, both at 100 mWcm^?2. Conductivity and photovoltaic parameters of the device reveals that as prepared polysulfobetaine‐based polymer gel electrolyte may be useful in the fabrication of DSSC and other electrochemical devices. Copyright © 2017 John Wiley & Sons, Ltd.     

Photovoltaic performance of dye-sensitized solar cells assembled by in-situ chemical cross-linking

Quasi-solid state dye-sensitized solar cells (DSSCs) were assembled by in-situ chemical cross-linking of a gel electrolyte precursor containing liquid electrolyte. The DSSCs assembled with this cross-linked gel polymer electrolyte showed higher open circuit voltage and lower short-circuit photocurrent density than those of DSSCs with liquid electrolyte. Addition of SiO₂ nanoparticles into the cross-linked gel polymer electrolyte significantly improved the photovoltaic performance and long-term stability of the DSSCs. The optimized quasi-solid state DSSC showed high conversion efficiency, 6.2% at 100 mW cm^?2 with good durability.     

水热法可控合成二氧化钛纳米晶及其在染料敏化太阳能电池中的应用

本文报道了水热法可控合成二氧化钛纳米晶及其在染料敏化太阳能电池中的应用.选择合适的有机碱胶化剂,能很好地控制二氧化钛纳米晶的生长,形成不同形貌和粒径的锐钛矿型二氧化钛纳米晶颗粒.染料敏化太阳能电池光电性能测试结果表明,以四乙基氢氧化铵为胶化剂合成的边长为8～13nm的正方形二氧化钛纳米晶构成的光阳极光电性能优于以四丁基氢氧化铵为胶化剂合成的边长为7～10nm的正方形二氧化钛纳米晶以及长18～35nm,宽10～18nm的长方形二氧化钛纳米晶构成的光阳极.用较高浓度的四甲基氢氧化铵胶化剂能合成球形或椭球形亚微米级二氧化钛颗粒,以其为散射中心在光阳极中构建散射层,染料敏化太阳能电池的光电转换效率能由6.77%提高到8.18%.     

Effect of organic dye on the performance of dye-sensitized solar cell utilizing TiO2 nanostructure films synthesized via CTAB-assisted liquid phase deposition technique

This work is concerned with the growth of TiO₂ nanostructures as photovoltaic materials of dyesensitized solar cell (DSSC) via phase liquid deposition technique treated with CTAB surfactant. This work investigates the influence of organic dyes, N719, N3 and Z907 as photosensitizer on the photovoltaic parameters of TiO₂ nanostructures dye-sensitized solar cells (DSSCs). It also highlights the effect of the concentration of the best dye, N719 on the performance of the cell. The platinum films as counter electrode of the DSSC were prepared by sputtering platinum pellet on ITO substrate. The redox couple of the electrolyte utilized in the DSSC was iodide/triiodide. The cell sensitized with N719 dye demonstrated the best performance compared with the cell sensitized with another two dyes, N3 and Z907. This is due to N719 dye possess the highest optical absorption in visible region. The cell sensitized with 0.8 mM N719 dye performs the highest short-circuit current density, J _sc and power conversion efficiency, η since it posses the highest absorption in visible region. The DSSC utilizing 0.8 mM N719 dye demonstrated the highest J _sc and η of 6.48 mA cm^?2 and 1.69%, respectively.     

Facile synthesis of TiO2 inverse opal electrodes for dye-sensitized solar cells

Engineering of TiO(2) electrode layers is critical to guaranteeing the photoconversion efficiency of dye-sensitized solar cells (DSSCs). Recently, a novel approach has been introduced for producing TiO(2) electrodes using the inverted structures of colloidal crystals. This paper describes a facile route to producing ordered macroporous electrodes from colloidal crystal templates for DSSCs. Using concentrated colloids dispersed in a volatile medium, the colloidal crystal templates were obtained within a few minutes, and the thickness of the template was easily controlled by changing the quantity of colloidal solution deposited. Here, the effects of the structural properties of the inverse opal TiO(2) electrodes on the photovoltaic parameters of DSSCs were investigated. The photovoltaic parameters were measured as a function of pore ordering and electrode film thickness. Moreover, DSSC applications that used either liquid or viscous polymer electrolyte solutions were investigated to reveal the effects of pore size on performance of an inverse opal TiO(2) electrode.     

Efficiency enhancement with chloride to iodide ion exchange of benzimidazolium salt as a redox mediator

The new benzimidazolium derivative (SM-1) salt with ion exchange from the (SM-0) was fabricated and characterized by proton-nuclear magnetic resonance (¹H-NMR), carbon-nuclear magnetic resonance (¹³C-NMR), Fourier-transform infrared spectroscopy (FT-IR), electrospray ionization (EIS-MS), thermal analysis (TG), cyclic voltammetry (CV), and ultraviolet-visible spectroscopy (UV-vis), for electrolytes (liquid or dried) in the DSSC charge transportation mechanism. Also, the influence of ion exchange from chloride to iodine in the synthesized electrolytes, compared to other electrolytes (conventional or commercial), was investigated about DSSC performance efficiency. When using as a liquid electrolyte (SM-1), the power conversion efficiency (ƞ) of the working DSSC device was recorded as 1.980% and it was observed that the performances of DSSCs increased up to 56% when comparing dried electrolyte for SM-1 without conventional redox material (I^-/I₃^-). In the future, different molecular modifications of this type of benzimidazole derivatives or mixtures with conventional redox couples may further improve the performance of DSSC devices.     

Non‐classical Design of High‐Efficiency Sensitizers for Dye‐Sensitized Solar Cells

The dye regeneration step in a dye‐sensitized solar cell (DSSC) affects significantly the device efficiency. To be able to predict the dye regeneration efficiency by the electrolyte this paper provides a facile way to design high‐efficiency sensitizers for DSSC. This paper proposes, for the first time, a simple and ingenious way to identify the dye regeneration sites and their relative efficiencies when a specific electrolyte is used. Two steps are proposed to identify the dye regeneration sites and their relative regeneration efficiencies: (1) drawing all the resonance structures of the oxidized dye to determine the regeneration sites, and (2) choosing the most favored site for dye regeneration as the chemically softest (when the redox couple used is soft I⁻/I₃⁻ pair) and the least spatially hindered site. The regeneration sites identified by the resonance structures are consistent with the β‐LUSO (β lowest unoccupied spin orbital) distribution, which is generally used for identifying the dye regeneration sites, calculated with DT‐DFT theory. The relative dye regeneration efficiency and photovoltaic performance of both ruthenium and metal‐free organic dyes predicted by the method reported here are supported by experimental data and the proposed dye regeneration mechanism. Several types of dye molecules are used to demonstrate the correctness of this new tool. This non‐classical tool, which uses the well‐known chemical knowledge of the resonance structure and hard–soft acid–base principle, without any computer calculation or physicochemical measurement, provides a very simple and powerful tool to quickly conceive high‐efficiency sensitizers for DSSCs.     

3, 4-乙烯二氧噻吩单体用作锂离子电池安全性改善添加剂的研究

安全性是制约锂离子电池向电动汽车领域应用拓展的主要障碍. 本工作提出了一种能够有效改善锂离子电池安全性的电解液添加剂-3,4-乙烯二氧噻吩单体（EDOT）,研究了其在有机电解液中的电氧化聚合行为,以及对LiCoO₂电极高温热行为和电池安全性、电化学性能的影响. 循环伏安（CV）和透射电镜（TEM）表征结果表明,单体添加剂能够在电池充电过程发生电氧化聚合,在正极表面形成一层聚（3,4-乙烯二氧噻吩）（PEDOT）导电聚合物膜;差示扫描量热（DSC）分析结果显示,PEDOT隔离了电解液与正极表面的直接接触,减少了过热条件下电解液在正极表面的分解放热. 安全性测试结果表明,在电解液中仅添加0.1%的EDOT单体,即可将电池在150 ^oC高温热冲击下发生热失控的时间推迟13.8分钟. 电化学性能测试结果表明,聚合产物良好的电子导电性能有效改善正极的电子传导能力,在一定程度上提高电池的倍率性能和循环稳定性,而容量、低温性能等基本不受影响,展示出良好的应用前景.