High transmission with narrow bandwidth of metallic defect mode in 1-D dielectric photonic crystals

Enhanced transmission peaks can be obtained in a dielectric photonic crystal with metal film defect. These peaks occur only in the band gaps, and their heights decrease sharply when they deviate from the band gaps. Theoretical analysis shows that, since the metal film defect mode possesses very high density of mode, high transmission of light in particular band can be achieved even by a metal “block” while high absorption of the light in other bands still exists. The physical mechanism of this phenomenon is essentially different from the resonant tunneling effect of layered metallic films. Since metal has high reflection and strong absorption of the light wave without being enhanced, so, basing on this mechanism, a narrow bandwidth filter with high transmission in UV range and suppression in while the visible, infrared, and even microwave range can be achieved.     

Fabrication of high-quality colloidal photonic crystals with sharp band edges for ultrafast all-optical switching

Application of the pressure controlled isothermal heating vertical deposition method to the fabrication of colloidal photonic crystals is systematically investigated in this paper. The fabricated samples are characterized by scanning electron microscope and transmission spectrum. High-quality samples with large transmissions in the pass bands and the sharp band edges are obtained and the optimum growth condition is determined. For the best sample, the transmission in the pass bands approaches 0.9 while that in the band gap reaches 0.1. More importantly, the maximum differential transmission as high as 0.1/nm is achieved. In addition, it is found that the number of stacking layers does not increase linearly with concentration of PS spheres in a solution, and a gradual saturation occurs when the concentration of PS spheres exceeds 1.5 wt.%. The uniformity of the fabricated samples is examined by transmission measurements on areas with different sizes. Finally, the tolerance of the fabricated samples to baking was studied.     

Fabrication of Colloidal Photonic Crystals with Heterostructure by Spin-Coating Method

Colloidal photonic crystal heterostructures, composed of two opaline photonic crystal films of silica spheres with different diameters, are fabricated by a two-step spin-coating method. Scanning electron microscopy （SEM） and UV-vis spectrophotometer are used to characterize the heterostructures. The SEM images show good ordering of the two-layer colloidal crystals constituting the heterostructures. The transmission spectra measured from the （111） plane in the heterostructure show that the composite colloidal photonic crystals have double photonic stop bands. Furthermore, when the sizes of the silica spheres used for fabricating the composite photonic crystal are slightly different, the transmission spectrum shows that the composite photonic crystals have more extended bandgap than that of the individual photonic crystals due to partial overlapping of its two photonic stop bands.     

二氧化硅胶体球自组装光子晶体的研究

光子晶体由于具有光子带隙和光子局域等一系列优异的光学特性而受到了人们广泛的关注。由于采用胶体颗粒自组装法制备光子晶体制备工艺简单,所需要的费用也较低,因此已成为制备可见光至红外波段三维光子晶体的一种简便有效的方法。采用垂直沉积法制得了三维光子晶体薄膜,并用扫描电子显微镜和紫外-可见光-近红外分光光度计对其显微结构和光学特性进行了详细的研究。结果表明,自组装薄膜在三维方向上都具有有序结构,其密排面平行于载波片的表面。制备的光子晶体薄膜具有明显的光子带隙特性,带隙中心波长为956nm。研究了带隙中心波长同入射线与密排面法线夹角之间的变化关系,其结果与理论值吻合得很好。     

Specific features of polarization anisotropy in optical reflection and transmission of colloidal photonic crystals

This paper reports on the measurements (in linearly polarized light) of the transmission and reflection spectra of colloidal photonic crystals with three-dimensional and one-two-dimensional photonic band structure, i.e., opal films and Langmuir-Blodgett crystals with a refractive index contrast of ∼1.5: 1.0. It has been shown that the polarization anisotropy is enhanced considerably in the diffraction resonance range both in transmitted and reflected light, and that the anisotropy in the resonance range can be as high as 99%. The interaction of photonic crystal eigenmodes has been found to affect the polarization anisotropy. The assumption has been made that the coincidence of the maxima in polarization anisotropy of the resonant and nonresonant light reflection in colloidal crystals originates from the disorder in their lattices. The generality of the results obtained is confirmed by the fact that the polarization anisotropy manifests itself in the same way in colloidal crystals with different lattice symmetries.     

Optical bistability in nonlinear surface-plasmon polaritonic crystals

Nonlinear optical transmission through periodically nanostructured metal films (surface-plasmon polaritonic crystals) has been studied. The surface polaritonic crystals have been coated with a nonlinear polymer. The optical transmission of such nanostructures has been shown to depend on the control-light illumination conditions. The resonant transmission exhibits bistable behavior with the control-light intensity. The bistability is different at different resonant signal wavelengths and for different wavelengths of the control light. The effect is explained by the strong sensitivity of the surface-plasmon mode resonances at the signal wavelength to the surrounding dielectric environment and the electromagnetic field enhancement due to plasmonic excitations at the controlled light wavelengths.     

Fabrication and characterization of photonic crystals with well-controlled thickness and stop-band attenuation

Photonic crystals with stop bands located in the visible region have been fabricated by crystallizing monodispersed spherical colloids (made of polystyrene or silica) into cubic-close-packed lattices within specially designed packing cells. These crystals were oriented with their (111) planes parallel to their solid supports, and the number of these planes could be conveniently controlled from 13 to 127 layers by varying the thickness of packing cells. In accordance, the stop-band attenuation of these crystals monotonically increased from 1 to 21 dB. Our transmission spectral measurements indicated that there exists a non-linear dependence between the stop-band attenuation and the total number of (111) planes, and this dependence could be quantitatively simulated using the dynamic light scattering model or the photonic analogy to KKR method. The colloidal crystals presented here should find use as components in fabricating optical devices that include sensors, mirrors, filters, switches and waveguides. Received: 17 May 2002 / Accepted: 25 July 2002 / Published online: 4 December 2002 RID="*" ID="*"Corresponding author. Fax: +1-206/685-8665, E-mail: xia@chem.washington.edu     

一维金属/介质光子晶体透射特性分析

阐述了一维金属/介质光子晶体的概念,采用时域有限差分法研究了不同金属等离子体频率和碰撞频率对一维金属/介质光子晶体透射特性的影响。计算结果表明,一维金属/介质光子晶体具有在可见光波段透明,在紫外波段以及红外至微波波段不透明的特性。对于结构相同的金属光子晶体,金属等离子体频率越低,金属光子晶体在可见光波段的透射允带就越宽,透射率越高,而金属的碰撞频率对透射允带没有显著的影响。     

高质量三维胶体光子晶体中慢光速与超光速的实验研究

利用飞秒脉冲自相关技术研究了高质量三维胶体光子晶体中的慢光速和超光速效应.实验中使用的胶体光子晶体是采用压力控制的绝热沉积技术（PCIHVD）制备的、由聚苯乙烯小球组成的人工蛋白石结构.由于其中的缺陷和位错密度很低,它们具有很高的通带透过率和陡峭的能带边缘.测量了从通带到带边直至带隙中央群速度的变化,在只有20层左右小球的样品中观察到低至0.43c的慢光速以及高至1.34c的超光速现象.此外,利用时域有限差分（FDTD）方法对短脉冲在三维光子晶体中的群速度进行了数值模拟,并且和 关键词： 三维胶体光子晶体 慢光速 超光速 脉冲自相关     

Implantation as a tool for performing selective materials (application to solar energy conversion)

A selective solar material must absorb most of the solar spectrum, principally the visible light, and reflect the IR light.

Insulators are generally transparent in a wide part of the optical spectrum and the defects are revealed in these crystals by strong absorption bands. On the other hand, metals absorb much of the IR and near IR light and have a large reflection coefficient in the same region of the spectrum. In previous papers^1,2 it has been shown that metallic colloids, formed by precipitation of impurities in insulators, are responsible for a strong absorption band. Such metallic inclusions may be easily produced in most insulators by implantation. According to the nature of the implanted metal a selective absorption can be obtained. So a composite material (cermet) may be performed combining a colloidal absorption in the visible and a metallic reflection. We will discuss the different ways to achieve these properties using direct ion beam implantation.

Various cermets (LiF: Na, Au; MgO: Na, Au) have been studied as function of energy (0.1-1 MeV) and dose (10¹⁶-10¹⁷ ions/cm²). Colloids are completely developed by consecutive annealing.⁴

The modelization of these cermets requires a careful characterization by optical methods (spectrophotometry) and microscopic investigation (TEM, SEM, RBS, SIMS).⁷ These techniques are used to determine the filling factor and the concentration profile of metal in the insulating matrix.

With the help of the Maxwell-Garnett theory and using a single or multilayer model it is possible to suggest an interpretation of the optical properties.     

Photoluminescence characteristics from amorphous SiC thin films with various structures deposited at low temperature

Hydrogenated amorphous SiC thin films deposited at low substrate temperature (100 °C) show the different bonding configurations and microstructures which depend on the carbon concentrations in the films controlled by the gas ratio R of methane to silane during the deposition. Photoluminescence characteristics are investigated for these samples with different structures. A strong luminescence in red light region can be observed for samples deposited with low gas ratio R which is significantly reduced its intensity with increasing the carbon concentrations in the films. On the other hand, the luminescence bands located at blue-green light region are detected under UV light excitation for samples deposited with high gas ratio R, which can be associated with the existence of amorphous SiC clusters in the films.     

Enhancement of extraction efficiency by metallic photonic crystal embedding in light-emitting diode

The bandgap effect of photonic crystals (PCs) and the effect of grating diffraction can be used to improve the extraction efficiency of light from the light-emitting diode (LED). The transmission of light at certain wavelength through periodic sub-wavelength hole arrays in metal films is extraordinary, surface plasmon (SP) effects effectively. In this letter, silver metallic photonic crystals with square lattice of cylinder unit cells are fabricated in GaN layer of GaN-based blue LED. We use the finite-difference time-domain (FDTD) method to investigate the optical transmission, the results show that the light extraction efficiency is enhanced by more than four times. Then we use the surface plasmon dispersion relation to analyze the mechanism of antireflection.     

Understanding plasmon resonances of metal-coated colloidal crystal monolayers

Metal films deposited over two-dimensional colloidal crystals (MFoCC) constitute a low-cost periodic structure with interesting photonic and plasmonic properties. It has previously been shown that this structure exhibits a behaviour similar to the well-known Extraordinary Optical Transmission (EOT) of metallic hole arrays in planar films. Here, we explore the transmission characteristics of AgFoCC by systematic comparison with that of the bare CC. Furthermore with additional reflectivity measurements we evaluate the AgFoCC overall plasmonic response, which, notably, exhibits a strong plasmon absorption band at wavelengths larger than those of the transmitted maximum. By corroborating these results with finite-difference time-domain electromagnetic simulations, we identify a hybrid metal-dielectric propagative mode in the transmission mechanism. On the contrary a strongly localized mode is responsible for the maximum light absorption by this structure. These results shed new light on the current understanding of this highly promising plasmonic structure, being useful for the design of surface-enhanced Raman scattering and enhanced fluorescence substrates.     

FCC结构胶体光子晶体的制备及其带隙特性测量

基于对光纤传输特性和胶体光子晶体制备方法的研究,提出了用外加电场控制的方法制备光子带隙位于通讯波段的FCC结构的胶体光子晶体,并用光纤系统测试胶体光子晶体的带隙特性.采用RSOFT模拟了胶体光子晶体的带隙,分析了带隙位于通讯波段时所需的胶体微球的基本参量(微球折射率和直径).采用自组装的方法,用步进电机控制玻璃基片向上的拉升速率.速率为5 μm/s,同时外加一电场.用扫描电镜观测胶体晶体的表面形貌,并设计了单模光纤系统测量胶体光子晶体的带隙特性.测试的透射谱线表明胶体光子晶体的带隙中心波长为1552 nm.测试结果和模拟结果具有很好的一致性,误差只有2 nm.     

光学波段菲波纳契序列一维光子晶体纳米膜传输特性研究

为了研究光学波段菲波纳契序列一维光子晶体纳米膜的传输特性,应用传输矩阵方法数值模拟各种情况下的透射率即传输函数随频率的变化.数值结果表明在正入射时,菲波纳契序列一维光子晶体中的禁带宽度、中心位置、数目都与构成序列的项数、组元物理厚度、组成序列组元初始次序、组元折射率差值都对传输特性有较大影响,在可见光区组元折射率差值越大越易形成较宽禁带,进一步研究广义菲波纳契序列一维光子晶体纳米膜的传输特性,发现比典型情况更易在可见光区形成禁带.     

Opals with a thin-film metallic defect-hybrid colloidal plasmonic photonic crystals

Hybrid photonic crystals consisting of a thin-film opal and a thin profiled gold film situated on the surface or inside the opal have been prepared. The optical transmittance spectra of hybrid crystals have been studied. It has been found that the spectra exhibit minima due to diffraction resonances in the photonic crystal and bands of enhanced transmission due to transfer of radiation through the metal film surface by plasmon polaritons. It has been shown that the transmittance spectra of hybrid crystals with a metal film on the surface are subjected to a stronger modification than the hybrids having a metal film inside the crystal.     

Electrically tunable diffraction of light from 2D nematic colloidal crystals

We show that diffraction of visible light from 2D dipolar nematic colloidal crystals can be tuned electrically. When the external electric field of ∼ 1V/μm is applied in a direction perpendicular to the plane of the 2D colloidal crystal, the induced strain is highly anisotropic, and the inter-colloidal spacing changes by as much as 20% along one direction and ∼ 2% along the perpendicular one. Although the speed of response is in the range of several seconds, this novel mechanism could provide interesting photonic applications.     

一维Au/MgF2光子晶体的透射性质

理论上研究了一维金属/电介质光子晶体的透射率性质,用传输矩阵方法数值计算了Au/MgF2光子带隙晶体的透射率．发现周期性结构产生的透射共振会大幅度增加光通过层状金属的透射率．通过调节一维Au/MgF2光子晶体中金和氟化镁的厚度以及周期数,得到了可见波段的高透射允带,透射率在0.4以上,而对于可见波段以外的频率几乎是完全不能传输的．这种结构在保持了高透射率的前提下还具有金属的优点,这在传感器、护目装置、反射窗、液晶显示等诸多领域都有很大的实用价值．     

Influence of implantation dose on electroluminescence from Si-implanted silicon nitride thin films

Strong visible electroluminescence (EL) with electrically tunable colors from violet to white has been observed from Si-implanted silicon nitride thin films. Influence of the implanted Si ion dose on both the current conduction and EL properties has been studied. With a larger excess Si concentration, the carrier transport is enhanced leading to a higher EL intensity, but the light emission efficiency is reduced. On the other hand, the increase of the excess Si concentration causes redshifts in the major EL bands and improves the transition of the EL colors with increasing current. The excess Si concentration is also found to have a significant influence on the EL degradation. These findings are important to the application of the Si-implanted thin films in light emitting devices.