Precise isotope ratio measurements for uranium, thorium and plutonium by quadrupole-based inductively coupled plasma mass spectrometry

Precise long-term measurements of uranium and thorium isotope ratios was carried out in 1 μg/L solutions using a quadrupole inductively coupled plasma mass spectrometer (ICP-QMS). The isotopic ratios of uranium (²³⁵U/ ²³⁸U = 1, 0.02 and 0.00725) were determined using a cross-flow nebulizer (CFN, at solution uptake rate of 1 mL/min) and a low-flow microconcentric nebulizer (MCN, at solution uptake rate of 0.2 mL/min) over 20 h. For 1 μg/L uranium solution (²³⁵U/²³⁸U = 1) relative external standard deviations (RESDs) of 0.05% and 0.044% using CFN and MCN, respectively, can be achieved. Additional short term isotope ratio measurements using a direct injection high-efficiency nebulizer (DIHEN) of 1 μg/L uranium solution (²³⁵U/²³⁸U = 1) at a solution uptake rate of 0.1 mL/min yielded an RSD of 0.06–0.08%. The sensitivity of solution introduction by DIHEN for uranium, thorium and plutonium (145 MHz/ppm, 150 MHz/ppm and 177 MHz/ppm, respectively) increased significantly compared to CFN and MCN and the solution uptake rate can be reduced to 1 μL/ min in DIHEN-ICP-MS. Isotope ratio measurements at an ultralow concentration level (e.g. determination of ²⁴⁰Pu/ ²³⁹Pu isotope ratio in a 10 ng/L Pu waste solution) were carried out for the characterization of radioactive waste and environmental samples.     

Determination of U/U atom ratio in uranium samples using liquid scintillation counting (LSC)

A correlation has been developed for the determination of ²³⁵U/²³⁸U atom ratio in uranium samples using liquid scintillation counting (LSC). The ²³⁵U/²³⁸U atom ratio determined by thermal ionization mass spectrometry (TIMS) was correlated to the ratio of (i) α-count rate and (ii) Cerenkov count rate due to ^234mPa in the sample; both measured by LSC. This correlation is linear over the range of ²³⁵U/²³⁸U atom ratio encountered in the nuclear fuel samples, i.e. the low enriched uranium (LEU) samples with ²³⁵U < 20 atom%. The methodology based on this correlation will be useful for the quick determination and verification of ²³⁵U/²³⁸U atom ratios in fuel samples using cost effective technique of LSC.     

Precise isotope ratio measurements for uranium, thorium and plutonium by quadrupole-based inductively coupled plasma mass spectrometry

Precise long-term measurements of uranium and thorium isotope ratios was carried out in 1 μg/L solutions using a quadrupole inductively coupled plasma mass spectrometer (ICP-QMS). The isotopic ratios of uranium (²³⁵U/ ²³⁸U = 1, 0.02 and 0.00725) were determined using a cross-flow nebulizer (CFN, at solution uptake rate of 1 mL/min) and a low-flow microconcentric nebulizer (MCN, at solution uptake rate of 0.2 mL/min) over 20 h. For 1 μg/L uranium solution (²³⁵U/²³⁸U = 1) relative external standard deviations (RESDs) of 0.05% and 0.044% using CFN and MCN, respectively, can be achieved. Additional short term isotope ratio measurements using a direct injection high-efficiency nebulizer (DIHEN) of 1 μg/L uranium solution (²³⁵U/²³⁸U = 1) at a solution uptake rate of 0.1 mL/min yielded an RSD of 0.06–0.08%. The sensitivity of solution introduction by DIHEN for uranium, thorium and plutonium (145 MHz/ppm, 150 MHz/ppm and 177 MHz/ppm, respectively) increased significantly compared to CFN and MCN and the solution uptake rate can be reduced to 1 μL/ min in DIHEN-ICP-MS. Isotope ratio measurements at an ultralow concentration level (e.g. determination of ²⁴⁰Pu/ ²³⁹Pu isotope ratio in a 10 ng/L Pu waste solution) were carried out for the characterization of radioactive waste and environmental samples. Received: 1 December 1998 / Revised: 25 January 1999 / Accepted: 31 January 1999     

Determination of U isotope ratios in sediments using ICP-QMS after sample cleanup with anion-exchange and extraction chromatography

The determination of uranium is important for environmental radioactivity monitoring, which investigates the releases of uranium from nuclear facilities and of naturally occurring radioactive materials by the coal, oil, natural gas, mineral, ore refining and phosphate fertilizer industries, and it is also important for studies on the biogeochemical behavior of uranium in the environment. In this paper, we describe a quadrupole ICP-MS (ICP-QMS)-based analytical procedure for the accurate determination of U isotope ratios (²³⁵U/²³⁸U atom ratio and ²³⁴U/²³⁸U activity ratio) in sediment samples. A two-stage sample cleanup using anion-exchange and TEVA extraction chromatography was employed in order to obtain accurate and precise ²³⁴U/²³⁸U activity ratios. The factors that affect the accuracy and precision of U isotope ratio analysis, such as detector dead time, abundance sensitivity, dwell time and mass bias were carefully evaluated and corrected. With natural U, a precision lower than 0.5% R.S.D. for ²³⁵U/²³⁸U atom ratio and lower than 2.0% R.S.D. for ²³⁴U/²³⁸U activity ratio was obtained with less than 90 ng uranium. The developed analytical method was validated using an ocean sediment reference material and applied to an investigation into the uranium isotopic compositions in a sediment core in a brackish lake in the vicinity of U-related nuclear facilities in Japan.     

Behavior of uranium along Jucar River (Eastern Spain): Determination of234U/238U and235U/238U ratios

The uranium concentration and the²³⁴U/²³⁸U,²³⁵U/²³⁸U activity ratios were studied in water samples from Jucar River, using low-level -spectrometry. The effects of pH, temperature and salinity were considered and more detailed sampling was done in the neighbourhood of Cofrentes Nuclear Plant (Valencia, Spain). Changes were observed in the uranium concentration with the salinity and the²³⁴U/²³⁸U activity ratio was found to vary with pH. Leaching and dilution, which depend on pH and salinity, are the probable mechanisms for these changes in the concentration of uranium and the activity ratios.     

The determination of235U/238U ratios by activation analysis utilizing high resolution γ-spectrometry

The application of high resolution γ-spectrometry to the direct determination of²³⁵U/²³⁸U isotopic ratios in small uranium samples after neutron activation is reported. The consistency obtained relative to mass spectrometrically determined isotopic ratios is better than 5% for isotopic ratios between 0.06885 and 1.095. The method is not subject to the main disadvantages of the known radiochemical methods for²³⁵U/²³⁸U isotopic ratio determinations, and should be appreciably more rapid compared to the solid-source mass spectrometric method giving the same precision.     

<Superscript>234</Superscript>U/<Superscript>238</Superscript>U and <Superscript>235</Superscript>U/<Superscript>238</Superscript>U ratios in domestic water from the environs of Obuasi mine in Ghana

Activity concentrations of ²³⁸U, ²³⁵U and ²³⁴U were determined in different sources of drinking water at the Obuasi gold mines and its surrounding areas in Ghana. Water samples collected from the mines and its surrounding areas were analyzed using direct gamma-ray spectrometry and neutron activation analysis. The ²³⁴U/²³⁸U and ²³⁵U/²³⁸U ratios were calculated and the mean values range from 1.27 to 1.38 and from 0.044 to 0.045 respectively. The average ²³⁴U/²³⁸U ratio was from 1.27 for groundwater to 1.38 for treated water, demonstrating the lack of equilibrium. The average ²³⁵U/²³⁸U activity ratio is 0.045, indicating that only natural uranium was detected in the samples investigated.     

Flow injection extraction chromatography with ICP-MS for thorium and uranium determination in human body fluids

A method based on flow injection extraction chromatography coupled to on-line ICP-MS (FI-EXC-ICPMS) has been developed and validated for simultaneous thorium and uranium determination in human body fluids. By using extraction chromatography, the limits of detection achieved for ²³²Th, ²³⁵U and ²³⁸U were 0.06 ng^.l^-1, 0.0014 ng^.l^-1 and 0.05 ng^.l^-1, respectively. The accuracy of the FI-EXC-ICPMS method was 102.4% and 101.5% with overall precision (RSD_max at 95% CI) of 5.3% and 4.9% for ²³²Th and ²³⁸U, respectively. The ²³⁵U/²³⁸U atom ratio is measured with 1.8% precision. The technique was employed for simultaneous thorium and uranium analyses in human urine and blood samples after microwave digestion. This revised version was published online in July 2006 with corrections to the Cover Date.     

Uranium series disequilibrium in the coastal surface sediments and sea water of the Arabian Sea

Nearshore surface sediments from various locations of the West Coast of India were leached by saturated ammonium carbonate solution for the extraction of uranium isotopes. The reagent chosen was found to have high efficiency for leaching uranium isotopes without attacking the mineral core of the sediment particle. The activity ratios of²³⁴U/²³⁸U are in the range of 1.11 to 1.14 and the activity ratios of²³⁵U/²³⁵U are in the range of 0.045 to 0.047. The respective activity ratios in leachates, and residues after removal of surface organic matter from the sediment particles by treatment with hydrogen peroxide and 0.05M HCl, revealed disequilibrium between²³⁸U and²³⁴U only in the surface organic matter. The activity ratios of²³⁴U/²³⁸U and²³⁵U/²³⁸U have also been determined in some seawater samples from the Arabian Sea.     

Fast evaluation of <Superscript>235</Superscript>U/<Superscript>238</Superscript>U ratio in nuclear spent fuel safe guard by thermal ionization mass spectrometry by using refractory metal oxides

A direct simple and fast method was established, to overcome the influence of low and high level impurities on the measurement of ²³⁵U/²³⁸U isotopic ratio in nuclear spent fuel safeguard by thermal ionization mass spectrometry (TIMS), by using refractory metal oxide. The addition of refractory metal oxides forming solution (RMOFS), in certain proportions alongside with the spent fuel solution on the sample filaments were found to be useful during the analysis of uranium isotopic ratio by TIMS. RMOFS (with oxide melting point exceeding 2,000 °C), and particularly that of magnesium, were found to be very effective in improving the quality of the ion signal of ²³⁵U and ²³⁸U, when added without the need for prior purification. Solutions of chromium, cerium, thorium, and magnesium were investigated, to select the more convenient one, and it was found that magnesium was very useful to start with. The method was very simple, improve both the accuracy and precision of the collected data, reduce the time required to achieve steady uranium pilot signal, and hence the over all time of the analysis, regardless of the level of impurities present.     

222Rn content and234U/238U activity ratio in groundwaters

Geochemical radioanalytical studies of groundwater were performed in the valleys of Villa de Reyes and San Luis Potosi (Mexico). The experiments were designed to measure radon and uranium content and²³⁴U/²³⁸U activity ratio in groundwater samples taken from wells in these sites and at the Nuclear Center of Salazar, Mexico.²²²Rn content varied depending on the sample source, reaching a maximum value of 235 pCi/l; uranium concentration results were less than 1 g/1 and²³⁴U/²³⁸U activity ratios were close to equilibrium.     

<Superscript>234</Superscript>U/<Superscript>235</Superscript>U activity ratios as a probe for the <Superscript>238</Superscript>U/<Superscript>235</Superscript>U half-life ratio

High-resolution alpha-particle spectrometry was performed on three uranium materials enriched in ²³⁵U. Besides the ²³⁵U peaks, separate peaks belonging to impurity traces of ²³⁴U could be quantified. Relying on the isotopic composition of the uranium, as determined by mass spectrometry, the ratio of the half-lives of ²³⁸U and ²³⁵U was determined via the activity ratio of ²³⁴U and ²³⁵U in the materials. As an intermediate link, the ²³⁴U/²³⁸U half-life ratio was taken from published mass spectrometric analyses of ‘secular equilibrium’ uranium material. The resulting half-life ratio T _1/2(²³⁸U)/T _1/2(²³⁵U) = 6.351±0.031 is in agreement with the commonly adopted half-life values determined by Jaffey et al.     

Anomalous behaviours of protactinium in the acid-leaching experiments on pitchblende

A series of leaching experiments with H₂O, HCl, HNO₂ and HF were carried out on a sample of pitchblende from Africa. Anomalously high²³¹Pa/²³⁵U ratios, which were not accompanied by similar enhancements of²³⁴U/²³⁸U and²³⁵U/²³⁸U ratios, were observed in some uranium fractions. The observed²³¹Pa/²³⁵U ratios varied between the values of 0.035±0.005 and 2,000±300 (Ci/Ci). These results are interpreted as due, primarily, to the difference in the chemical properties of protactinium and uranium, rather than to the alpha-recoil effects.     

Isotopic and ultratrace analysis of uranium by double-focusing sector field ICP mass spectrometry

An analytical method for the ultratrace and isotopic analysis of uranium in radioactive waste samples using a double-focusing sector field ICP mass spectrometer is described. In high-purity water a detection limit for uranium in the lowest fg/mL range has been achieved. Under optimum experimental conditions (²³⁵U/²³⁸U ≈ 1), the precision in ²³⁵U/²³⁸U isotopic ratio determinations has been determined as 0.07% RSD. With the isotopic standard U-020 (²³⁵U/²³⁸U = 0.0208) a precision of 0.23% RSD at the 100 pg/mL level using ultrasonic nebulization has been achieved. With ²³⁴U/²³⁸U isotopic ratios of down to 10^–5, the values obtained by double-focusing sector field ICP-MS and alpha spectrometry were in agreement. Received: 27 February 1997 / Revised: 10 Juni 1997 / Accepted: 12 June 1997     

Application of Inductively Coupled Plasma Mass Spectrometry to the determination of uranium isotope ratios in individual particles for nuclear safeguards

The capability of inductively coupled plasma mass spectrometry (ICP-MS) for the determination of uranium isotope ratios in individual particles was determined. For this purpose, we developed an experimental procedure including single particle transfer with a manipulator, chemical dissolution and isotope ratio analysis, and applied to the analysis of individual uranium particles in certified reference materials (NBL CRM U050 and U350). As the result, the ²³⁵U/²³⁸U isotope ratio for the particle with the diameter between 0.5 and 3.9 μm was successfully determined with the deviation from the certified ratio within 1.8%. The relative standard deviation (R.S.D.) of the ²³⁵U/²³⁸U isotope ratio was within 4.2%. Although the analysis of ²³⁴U/²³⁸U and ²³⁶U/²³⁸U isotope ratios gave the results with inferior precision, the R.S.D. within 20% was possible for the measurement of the particle with the diameter more than 2.1 μm. The developed procedure was successfully applied to the analysis of a simulated environmental sample prepared from a mixture of indoor dust (NIST SRM 2583) and uranium particles (NBL CRM U050, U350 and U950a). From the results, the proposed procedure was found to be an alternative analytical tool for nuclear safeguards.     

Determination of uranium isotopic composition and 236U content of soil samples and hot particles using inductively coupled plasma mass spectrometry

As a result of the accident at the Chernobyl nuclear power plant (NPP) the environment was contaminated with spent nuclear fuel. The ²³⁶U isotope was used in this study to monitor the spent uranium from nuclear fallout in soil samples collected in the vicinity of the Chernobyl NPP. Nuclear track radiography was applied for the identification and extraction of hot radioactive particles from soil samples. A rapid and sensitive analytical procedure was developed for uranium isotopic ratio measurement in environmental samples based on double-focusing inductively coupled plasma mass spectrometry (DF–ICP–MS) with a MicroMist nebulizer and a direct injection high-efficiency nebulizer (DIHEN). The performance of the DF–ICP–MS with a quartz DIHEN and plasma shielded torch was studied. Overall detection efficiencies of 4×10^–4 and 10^–3 counts per atom were achieved for ²³⁸U in DF–ICP–QMS with the MicroMist nebulizer and DIHEN, respectively. The rate of formation of uranium hydride ions UH⁺/U⁺ was 1.2×10^–4 and 1.4×10^–4, respectively. The precision of short-term measurements of uranium isotopic ratios (n = 5) in 1 μg L^–1 NBS U-020 standard solution was 0.11% (²³⁸U/²³⁵U) and 1.4% (²³⁶U/²³⁸U) using a MicroMist nebulizer and 0.25% (²³⁵U/²³⁸U) and 1.9% (²³⁶U/²³⁸U) using a DIHEN. The isotopic composition of all investigated Chernobyl soil samples differed from those of natural uranium; i.e. in these samples the ²³⁶U/²³⁸U ratio ranged from 10^–5 to 10^–3. Results obtained with ICP–MS, α- and γ-spectrometry showed differences in the migration properties of spent uranium, plutonium, and americium. The isotopic ratio of uranium was also measured in hot particles extracted from soil samples.     

A comparative study of some nuclear methods for235U/238U isotopic ratios determination

In the present work, a comparative study is made among nuclear methods for²³⁵U/²³⁸U ratios determination: activation analysis followed by high-resolution gamma-ray spectrometry, delayed neutron counting, passive gamma-ray and alpha spectrometry. Activation analysis followed by high-resolution gamma-ray spectrometry yielded a relative standard deviation down to 0.1% and a relative error of about 1% for standards of uranium enriched to 14%. Passive gamma-ray spectrometry using Ge(Li) detectors yielded a relative error down to 0.1% for enriched uranium and values even lower for the standard deviation. Passive gamma-ray spectrometry using Low Energy Photon Detector (LEPD) yielded a precision of 0.2% and a still better accuracy for enriched standards. In the case of alpha spectrometry, a relative error down to 0.5% and a precision of about 1% were obtained, also for enriched uranium standards. Delayed neutron counting allowed a relative standard deviation of about 7% and a relative error of about 2%, for standards of depleted uranium.     

Determination of234U/238U activity ratios in Syrian phosphates

The concentrations of uranium and the²³⁴U/²³⁸U ratio in natural Syrian phosphates were measured by gamma- and alpha-ray spectroscopy. The²³⁴U/²³⁸U activity ratios showed that uranium in Syrian phosphate is in equilibrium under the climatic conditions. Soma anomalous observations in these ratios were explained by earlier leaching of the phosphate by water (rain or other).     

Anomalous behaviour of uranium isotopes in backwater sediments of Zuari river

The surface leaching of the labile component of uranium has been carried out in estuarine sediments of Zuari river in Goa. The measurements of alpha activities of²³⁸U,²³⁵U and²³⁴U in the leachates indicated a remarkable anomaly between the activities of²³⁸U and²³⁴U. The activity ratios of²³⁴U/²³⁸U in these leachates have been found to be in the range of 1.10 to 1.14. However, the activity ratios of²³⁵U/²³⁸U have been found to be 0.045 which is close to that in natural uranium. It has also been observed that the anomaly between²³⁸U and²³⁴U exists only on the surface organic layers of the backwater sediments of the Zuari river.     

Comparison of AMS,TIMS, and SIMS techniques for determining uranium isotope ratios in individual particles

The determination of isotope ratios in individual uranium particles is very important for nuclear safeguards. In this work, accelerator mass spectrometry (AMS), thermal ionization mass spectrometry (TIMS), and secondary ion mass spectrometry (SIMS) were applied to isotope ratio analysis of individual uranium particles and compared in terms of background, measurement accuracy, and efficiency. Several individual uranium particles (1–7 μm) from certified reference materials were used as samples. The results show that the average values of blank counting rate of ²³⁵U for AMS, FT-TIMS (FT: fission track), SEM-TIMS (SEM: scanning electron microscope), and SIMS were 7.3, 7.8, 2.7 and 2.2 cps, respectively. The relative error of ²³⁴U/²³⁵U and ²³⁴U/²³⁶U isotope ratios of the particles from U200 for AMS were within 10% and 20%, whereas the results of FT-TIMS and SIMS were within 5% and 10%, respectively. The relative error and external precision of ²³⁴U/²³⁸U and ²³⁵U/²³⁸U of the particles from U850 for the method of AMS, SEM-TIMS, and SIMS were within 10% and 5%, respectively. For ²³⁶U/²³⁸U, the average values of the relative error and external precision measured by AMS were within 5%, which measured by SEM-TIMS and SIMS were all within 10%. AMS has advantages in measuring ²³⁶U/²³⁸U. The measurement time of AMS and SEM-TIMS was shorter than that of FT-TIMS and longer than that of SIMS. It is considered that AMS and SEM-TIMS have a certain development prospect, and it is necessary to research deeply.