Construction of an inexpensive surface plasmon resonance instrument for use in teaching and research

The construction of an inexpensive SPR instrument that can be used for both teaching and research is described. Using a 2′ × 2′ optical table to construct this instrument allows both scientists and students full access to the operation of the spectrometer. Furthermore, the use of open platform instrumentation has the advantage of maintaining the focus on the relationship between emerging technology and analytical chemistry as well as allowing the user to modify the instrument to enhance the measurement process for a particular application. This is a change from the learning paradigm used in most research and teaching laboratories where commercial instrumentation is treated as a black box due to its complexity. Three studies, which were performed using this instrument, are presented to demonstrate the suitability of this instrument for both teaching and research. These studies include measuring the refractive index of alcohols, investigating the partitioning of ruthenium (II) trisbipyridine chloride into Nafion, and understanding the mechanism controlling metal ion adsorption by polyacrylamide hydrogels.     

A surface plasmon resonance probe without optical fibers as a portable sensing device

A surface plasmon resonance (SPR) sensor integrating a small sensor probe, a laser emission diode, a photo detector, and a polarizer was developed as a portable sensing device. The sensor probe was made with a glass cylinder, 50 mm long and 1.5 mm in diameter, that was connected directly to a beam splitter without optical fibers. The SPR spectrum obtained with this probe system showed a 10% reflectivity minimum at 690 nm. Shifts of the SPR spectrum induced by refractive index (RI) changes in the sample were measured by detecting the reflection light intensity at 670 nm. When the sensitivity was compared using a BIAcore™ SPR instrument, the lowest sensor response of 1 mV observed with the SPR probe system coincided with 1.4 × 10⁻⁶ of the RI changes. The RI resolution of the SPR probe was estimated with experimentally evaluated noise on the signal, and, consequently, it was concluded that the RI resolution was 1.2 × 10⁻⁵. Moreover, immunoreaction was demonstrated with adsorbed bovine serum albumin (BSA) and anti-BSA antibody as an analyte. As a result, 50 ng mL⁻¹ of the lower detection limit was estimated.     

Recent advances in surface plasmon resonance based techniques for bioanalysis

Surface plasmon resonance (SPR) is a powerful and versatile spectroscopic method for biomolecular interaction analysis (BIA) and has been well reviewed in previous years. This updated 2006 review of SPR, SPR spectroscopy, and SPR imaging explores cutting-edge technology with a focus on material, method, and instrument development. A number of recent SPR developments and interesting applications for bioanalysis are provided. Three focus topics are discussed in more detail to exemplify recent progress. They include surface plasmon fluorescence spectroscopy, nanoscale glassification of SPR substrates, and enzymatic amplification in SPR imaging. Through these examples it is clear to us that the development of SPR-based methods continues to grow, while the applications continue to diversify. Major trends appear to be present in the development of combined techniques, use of new materials, and development of new methodologies. Together, these works constitute a major thrust that could eventually make SPR a common tool for surface interaction analysis and biosensing. The future outlook for SPR and SPR-associated BIA studies, in our opinion, is very bright. Surface plasmon resonance (SPR) is a powerful and versatile spectroscopic method for biomolecular interaction analysis (BIA) and has been well reviewed in previous years. This updated 2006 review of SPR, SPR spectroscopy, and SPR imaging explores cutting-edge technology with a focus on material, method, and instrument development. A number of recent SPR developments and interesting applications for bioanalysis are provided. Three focus topics are discussed in more detail to exemplify recent progress. They include surface plasmon fluorescence spectroscopy, nanoscale glassification of SPR substrates, and enzymatic amplification in SPR imaging. Through these examples it is clear to us that the development of SPR-based methods continues to grow, while the applications continue to diversify. Major trends appear to be present in the development of combined techniques, use of new materials, and development of new methodologies. Together, these works constitute a major thrust that could eventually make SPR a common tool for surface interaction analysis and biosensing. The future outlook for SPR and SPR-associated BIA studies, in our opinion, is very bright.      

Real-time immunoassay of ferritin using surface plasmon resonance biosensor

A surface plasmon resonance (SPR) biosensor was used for the first time to determine the concentration of ferritin in both HBS-EP buffer and serum. The monoclonal antibody was immobilized on the carboxymethyl dextran-modified gold surface by an amine coupling method. The interaction of antibody with antigen was monitored in real-time. The signal was enhanced by sandwich amplification strategy to improve the sensitivity and specificity of the immunoassay, especially in serum. The linear range of the assay in serum is over 30-200 ng ml⁻¹ with the detection limit of 28 ng ml⁻¹. The sensitivity, specificity, and reproducibility of the assay are satisfactory. The analyte and enhancement antibody-binding surface could be regenerated by pH 2.0 glycine-HCl buffer and the same antibody-immobilized surface could be used for more than 50 cycles of ferritin binding and regeneration.     

Detection of ozone gas using gold nanoislands and surface plasmon resonance

Gold nanoislands interact with gaseous ozone to produce a surface plasmon resonance shift, similarly to the interaction of ozone and gold nanoparticles in water. Gold nanoislands are produced by sputtering, which significantly simplifies the synthesis and produces controlled size for the gold nanoislands. The shift of surface plasmon resonance peak was monitored while gold nanoislands were exposed to variable concentration of gaseous ozone. The shift was then correlated with ozone concentration. Our current results indicate sensing gaseous ozone at concentration of as low as 20 μg/L is achievable. Gold nanoislands were reversed to their original wavelength and were able to cycle between the wavelengths as ozone was introduced and removed. Potentially, this system can be useful as a sensor that identifies the presence of ozone at low part-per-billion concentrations of ozone in gaseous media.     

Rapid detection of nivalenol and deoxynivalenol in wheat using surface plasmon resonance immunoassay

A surface plasmon resonance (SPR) immunoassay using a monoclonal antibody was developed to measure nivalenol (NIV) and deoxynivalenol (DON) contamination in wheat. A highly sensitive and stable DON-immobilized sensor chip was prepared, and an SPR detection procedure was developed. The competitive inhibition assay used a monoclonal antibody that cross-reacts with NIV and DON. The half maximal inhibitory concentration (IC₅₀) values of the SPR assay were 28.8 and 14.9 ng mL⁻¹ for NIV and DON, respectively. The combined responses of NIV and DON in wheat were obtained using a simultaneous detection assay in a one-step cleanup procedure. NIV and DON were separated using a commercial DON-specific immunoaffinity column (IAC) and their responses were obtained using an independent detection assay. Spiked tests using these toxins revealed that recoveries were in the range 91.5-107% with good relative standard deviations (RSDs) (0.40-4.1%) and that detection limits were 0.1 and 0.05 mg kg⁻¹ for NIV and DON, respectively. The independent detection using IAC showed detection limits of 0.2 and 0.1 mg kg⁻¹ for NIV and DON, respectively. SPR analysis results were correlated with those obtained using a conventional LC/MS/MS method for wheat co-contaminated with NIV and DON. These results suggested that the developed SPR assay is a practical method to rapidly screen the NIV and DON co-contamination of wheat and one of a very few immunoassays to detect NIV directly.     

Label-free detection of cancer biomarker candidates using surface plasmon resonance imaging

In this work, we present an antibody array for the detection of cancer biomarker candidates by a surface plasmon resonance (SPR) imaging sensor with polarization contrast. Responses from the SPR imaging sensor are shown to be similar to those from a conventional spectroscopy-based SPR sensor. Antibodies are spotted onto a self-assembled monolayer (SAM) composed of oligo(ethylene glycol) (OEG)-containing alkanethiol chains. Detection of two cancer biomarker candidates, activated leukocyte cell adhesion molecule/CD 166 (ALCAM) and transgelin-2 (TAGLN2), is demonstrated. Limits of detection for ALCAM and TAGLN2 are established at 6 ng/mL and 3 ng/mL, respectively, in buffer. No cross-reactivity is observed between immobilized antibodies and nonspecific antigen. Biomarker candidates are also detected in a 10% human serum solution. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Detection of microcystins in environmental samples using surface plasmon resonance biosensor

An indirect inhibitive surface plasmon resonance (SPR) immunoassay was developed for the microcystins (MCs) detection. The bioconjugate of MC-LR and bovine serum albumin (BSA) was immobilized on a CM5 sensor chip. A serial premixture of MC-LR standards (or samples) and monoclonal antibody (mAb) were injected over the functional sensor surface, and the subsequent specific immunoreaction was monitored on the BIAcore 3000 biosensor and generated a signal with an increasing intensity in response to the decreasing MCs concentration. The developed SPR immunoassay has a wide quantitative range in 1-100 μg L⁻¹. Although not as sensitive as conventional enzyme-linked immunosorbent assay (ELISA), the SPR biosensor offered unique advantages: (1) the sensor chip could be reusable without any significant loss in its binding activity after 50 assay-regeneration cycles, (2) one single assay could be accomplished in 50 min (including 30-min preincubation and 20-min BIAcore analysis), and (3) this method did not require multiple steps. The SPR biosensor was also used to detect MCs in environmental samples, and the results compared well with those obtained by ELISA. We conclude that the SPR biosensor offers outstanding advantages for the MCs detection and may be further developed as a field-portable sensor for real-time monitoring of MCs on site in the near future.     

Organic vapour sensing using localized surface plasmon resonance spectrum of metallic nanoparticles self assemble monolayer

The response of localized surface plasmon resonance (LSPR) spectra of gold and silver nanoparticles, and gold nanoshells to organic vapors was investigated. The surface area of nanomaterials was sufficiently high for quantitative adsorption of volatile organic compounds (VOCs). Surface adsorption and condensation of VOCs caused the environmental refractive index to increase from n = 1.00 in pure air to as high as n = 1.29 in near saturated toluene vapor. The extinction and wavelength shift of the LSPR spectra were very sensitive to changes in the surface refractive index of the nanoparticles. Responses of the LSPR band were measured with a real-time UV-vis spectrometer equipped with a CCD array detector. The response of silver nanoparticles to organic vapors was most sensitive in changes in extinction, while gold nanoshells exhibited red-shifts in wavelength (∼250 nm/RIU) when exposed to organic vapors. The LSPR spectral shifts primarily were determined by the volatility and refractive indices of the organic species. The T₉₀ response time of the VOC-LSPR spectrum was less than 3 s and the response was completely reversible and reproducible.     

Ultrasensitively sensing acephate using molecular imprinting techniques on a surface plasmon resonance sensor

An ultrathin molecularly imprinted polymer film was anchored on an Au surface for fabricating a surface plasmon resonance sensor sensitive to acephate by a surface-bound photo-radical initiator. The polymerization in the presence of acephate resulted in a molecular-imprinted matrix for the enhanced binding of acephate. Analysis of the SPR wavenumber changes in the presence of different concentrations of acephate gave a calibration curve that included the ultrasensitive detection of acephate by the imprinted sites in the composite, K_ass for the association of acephate to the imprinted sites, 7.7 × 10¹² M⁻¹. The imprinted ultrathin film revealed impressive selectivity. The selectivity efficiencies for acephate and other structurally related analogues were 1.0 and 0.11-0.37, respectively. Based on a signal to noise ratio of 3, the detection limits were 1.14 × 10⁻¹³ M for apple sample and 4.29 × 10⁻¹⁴ M for cole sample. The method showed good recoveries and precision for the apple and cole samples spiked with acephate solution. This suggests that a combination of SPR sensing with MIP film is a promising alternative method for the detection of organophosphate compounds.     

Development of surface chemistry for surface plasmon resonance based sensors for the detection of proteins and DNA molecules

The immobilisation of biological recognition elements onto a sensor chip surface is a crucial step for the construction of biosensors. While some of the optical biosensors utilise silicon dioxide as the sensor surface, most of the biosensor surfaces are coated with metals for transduction of the signal. Biological recognition elements such as proteins can be adsorbed spontaneously on metal or silicon dioxide substrates but this may denature the molecule and can result in either activity reduction or loss. Self assembled monolayers (SAMs) provide an effective method to protect the biological recognition elements from the sensor surface, thereby providing ligand immobilisation that enables the repeated binding and regeneration cycles to be performed without losing the immobilised ligand, as well as additionally helping to minimise non-specific adsorption. Therefore, in this study different surface chemistries were constructed on SPR sensor chips to investigate protein and DNA immobilisation on Au surfaces. A cysteamine surface and 1%, 10% and 100% mercaptoundecanoic acid (MUDA) coatings with or without dendrimer modification were utilised to construct the various sensor surfaces used in this investigation. A higher response was obtained for NeutrAvidin immobilisation on dendrimer modified surfaces compared to MUDA and cysteamine layers, however, protein or DNA capture responses on the immobilised NeutrAvidin did not show a similar higher response when dendrimer modified surfaces were used.     

Inhibition binding studies of glycodendrimer/lectin interactions using surface plasmon resonance

Understanding protein/carbohydrate interactions is essential for elucidating biological pathways and cellular mechanisms but is often difficult due to the prevalence of multivalent interactions. Here, we evaluate the multivalent glycodendrimer framework as a means to describe the inhibition potency of multivalent mannose-functionalized dendrimers using surface plasmon resonance (SPR). Using highly robust, mannose-functionalized dithiol self-assembled monolayers on gold surfaces, we found that glycodendrimers were efficient inhibitors of protein/carbohydrate interactions. IC₅₀ values ranging from 260 nM to 13 nM were obtained for mannose-functionalized dendrimers with Concanavalin A.     

Detection of parathion methyl using a surface plasmon resonance sensor combined with molecularly imprinted films

An ultra-sensitive and highly selective parathion methyl(PM) detection method by surface plasmon resonance(SPR) combined with molecularly imprinted films(MIF) was developed. The PM-imprinted film was prepared by thermo initiated polymerization on the bare Au surface of an SPR sensor chip.Template PM molecules were quickly removed by an organic solution of acetonitrile/acetic acid(9:1,v/v), causing a shift of 0.58 in SPR angle. In the concentrations range of 10à13–10à10mol/L, the refractive index showed a gradual increase with higher concentrations of template PM and the changes of SPR angles were linear with the negative logarithm of PM concentrations. In the experiment, the minimum detectable concentration was 10à13mol/L. The selectivity of the thin PM-imprinted film against diuron,tetrachlorvinphose and fenitrothion was examined, but no observable binding was detected. The results in the experiment suggested that the MIF had the advantages of high sensitivity and selectivity.     

Modeling protein binding and elution over a chromatographic surface probed by surface plasmon resonance

Surface plasmon resonance (SPR) spectroscopy is used as a scaled-down, analytical, pseudo-chromatography tool for analyzing protein binding and elution over an ion-exchange surface under cyclic sorption conditions. A micrometric-scale adsorption surface was produced by immobilizing a typical ion exchange ligand – diethylaminoethyl (DEAE) – onto commercially available planar gold sensor chip surfaces pre-derivatized with a self-assembled monolayer of 11-mercaptoundecanoic acid with known density. An explicit mathematical formulation is provided for the deconvolution and interpretation of the SPR sensorgrams. An adsorption rate model is proposed to describe the SPR sensorgrams for bovine serum albumin, used here as model protein, when the DEAE surface is subjected to a cyclic series of binding and elution steps. Overall, we demonstrate that the adsorption rate model is capable of quantitatively describing BSA binding and elution for protein titers from dilute conditions up to overloaded conditions and a broad range of salt concentrations.     

Development of an ultra-low volume flow cell for surface plasmon resonance detection in a miniaturized capillary electrophoresis system

A miniaturized capillary electrophoresis system coupled to a surface plasmon resonance (SPR) sensor on a microfluidic platform fabricated from PDMS is detailed. A previously described split-flow injection technique is first utilized to manipulate sample into the microfluidic chip, followed by separation within the fused-silica capillary and final off-capillary detection of analytes via SPR. Instead of using commercial SPR flow cells requiring relatively large detection volumes, samples of less than 1 nL volume are utilized. The interface between the CE system and SPR sensor made it possible to detect minute volumes of sample with minimal dispersion. The flow cell has the potential to be applicable to miniaturized flow-injection (FI) systems where submicroliter volumes of sample are frequently only available for analysis. The components present in solution, but not bound to the sensor surface, were also investigated. The sensitivity of the CE-SPR system was similar to that found in UV-spectrometric instruments and nonchromophoric components could also be measured.     

Studies on surface plasmon resonance and photoluminescence of silver nanoparticles

Silver nanoparticles of different sizes were prepared by citrate reduction and characterized by UV-vis absorbance spectra, TEM images and photoluminescence spectra. The morphology of the colloids obtained consists of a mixture of nanorods and spheres. The surface plasmon resonance (SPR) and photoemission properties of Ag nanoparticles are found to be sensitive to citrate concentration. A blue shift in SPR and an enhancement in photoluminescence intensity are observed with increase in citrate concentration. Effect of addition of KCl and variation of pH in photoluminescence was also studied.     

Present and future of surface plasmon resonance biosensors

Surface plasmon resonance (SPR) biosensors are optical sensors exploiting special electromagnetic waves—surface plasmon-polaritons—to probe interactions between an analyte in solution and a biomolecular recognition element immobilized on the SPR sensor surface. Major application areas include detection of biological analytes and analysis of biomolecular interactions where SPR biosensors provide benefits of label-free real-time analytical technology. This paper reviews fundamentals of SPR affinity biosensors and discusses recent advances in development and applications of SPR biosensors.     

Enhanced surface plasmon resonance immunoassay for human complement factor 4

Using an enhanced surface plasmon resonance (SPR) immunosensor, we have determined the concentration of human complement factor 4 (C4). Antibody protein was concentrated into a carboxymethyldextran-modified gold surface by electrostatic attraction force and a simultaneous covalent immobilization of antibody based on amine coupling reaction took place. The sandwich method was applied to enhance the response signal and the specificity of antigen binding assay. The antibody immobilized surface had good response to C4 in the range of 0.02-20 μg/ml by this enhanced immunoassay. The regeneration effect by pH 2 glycine-HCl buffer was also investigated. The same antibody immobilized surface could be used more than 80 cycles of C4 binding and regeneration. In addition, the ability to determinate C4 directly from serum sample without any purification was investigated. The sensitivity, specificity and reproducibility of the enhanced immunoassay are satisfactory. The results clearly demonstrate the advantages of the enhanced SPR technique for C4 immunoassay.     

Formation of photo-functional spiroxazine monolayers and their dielectric constant determination using surface plasmon resonance

Spiroxazine are of considerable interest as photochromic materials because of their application. On the other hand, surface plasmon resonance (SPR) is a well-known optical method for measuring optical constants of thin film. In this study, photochromic materials were used as self-assembled monolayers (SAMs) of newly synthesized spiroxazine derivatives. We used Fresnel equation (four-layer model) to determine the precise dielectric constant () of the photochromic monolayers. Structure changes of spiroxazine derivatives under UV-light irradiation resulted in the change of optical constants, the dielectric constant and thickness. The obtained results indicated that the ring opening of photochromic spiroxazine can lead to the decrease in the dielectric constant and thickness.     

Computer screen photo-excited surface plasmon resonance imaging

Angle and spectra resolved surface plasmon resonance (SPR) images of gold and silver thin films with protein deposits is demonstrated using a regular computer screen as light source and a web camera as detector. The screen provides multiple-angle illumination, p-polarized light and controlled spectral radiances to excite surface plasmons in a Kretchmann configuration. A model of the SPR reflectances incorporating the particularities of the source and detector explain the observed signals and the generation of distinctive SPR landscapes is demonstrated. The sensitivity and resolution of the method, determined in air and solution, are 0.145 nm pixel⁻¹, 0.523 nm, 5.13 × 10⁻³ RIU degree⁻¹ and 6.014 × 10⁻⁴ RIU, respectively, encouraging results at this proof of concept stage and considering the ubiquity of the instrumentation.