The effect of annealing on structural,optical and electrical properties of ZnS/porous silicon composites

ZnS films were prepared by pulsed laser deposition (PLD) on porous silicon (PS) substrates. This paper investigates the effect of annealing temperature on the structural, morphological, optical and electrical properties of ZnS/PS composites by x-ray diffraction (XRD), scanning electron microscope (SEM), photoluminescence (PL) and I–V characteristics. It is found that the ZnS films deposited on PS substrates were grown in preferred orientation along β-ZnS (111) direction, and the intensity of diflraction peak increases with increasing annealing temperature, which is attributed to the grain growth and the enhancement of crystallinity of ZnS films. The smooth and uniform surface of the as-prepared ZnS/PS composite becomes rougher through annealing treatment, which is related to grain growth at the higher annealing temperature. With the increase of annealing temperature,the intensity of self-activated luminescence of ZnS increases, while the luminescence intensity of PS decreases, and a new green emission located around 550 nm appeared in the PL spectra of ZnS/PS composites which is ascribed to the defect-center luminescence of ZnS. The I-V characteristics of ZnS/PS heterojunctions exhibited rectifying behavior, and the forward current increases with increasing annealing temperature.     

Effect of annealing on structural and optical properties of lead tungstate microcrystals

Shuttle-like lead tungstate (PbWO₄) microcrystals are synthesized at room temperature using the precipitation method with the cetyltrimethyl ammonium bromide. Results from both the X-ray diffraction and the scanning electron microscopy show that the lattice distortions of the PbWO₄ microcrystals are reduced significantly when the annealing temperature is increased to 873 K. The result from the ultraviolet-visible diffuse reflectance spectroscopy shows that the exciton absorption appears in the sample annealed at 673 K. The self-trapped exciton luminescence due to the Jahn-Teller effect is also observed in the blue band. The interstitial oxygen ions in the WO₄^2- groups are mainly resposible for the enhancement effect of the green luminescence of the annealed samples. The above results are supported by the spectrum analysis of the as-grown and the post-annealed samples using the X-ray photoelectron spectroscopy.     

Effects of annealing on structural,optical and electrical properties of Al-doped ZnO thin films

Transparent conducting oxide (TCO) thin films such as SnO2, In2O3, and Cd2SnO4, have been used extensively as sensor devices, surface acoustic wave devices, coating to heat glass windows and transparent electrodes for solid state display devices, solar cells[1,2] because of their high optical transparency in the visible range, infrared reflec-tance and low d.c. resistivity. Although SnO2 film was developed early, nowadays Sn-doped In2O3 (ITO) films are the predominant TCO thin film in …     

Ti离子注入和退火对ZnS薄膜结构和光学性质的影响

利用真空蒸发法在石英玻璃衬底上制备了ZnS薄膜,将能量80 keV,剂量1×10¹⁷ cm^-2的Ti离子注入到薄膜中,并将注入后的ZnS薄膜进行退火处理,退火温度500—700 ℃.利用X射线衍射（XRD）研究了薄膜结构的变化,利用光致发光（PL）和光吸收研究了薄膜光学性质的变化.XRD结果显示,衍射峰在500 ℃退火1 h后有一定程度的恢复;光吸收结果显示,离子注入后光吸收增强,随着退火温度的上升,光吸收逐渐降低,吸收边随着退火温度的提高发生蓝移;PL显示,薄 关键词： ZnS薄膜 离子注入 X射线衍射 光致发光     

Effect of annealing on the optical and electrical properties of ZnO:Er films

The effect of dopant concentration and annealing in the oxidizing atmosphere on the structural, optical, and electrical properties of ZnO:Er films deposited on sapphire substrates by the electron-beam evaporation method is investigated. The optical and electrical properties of these films were studied by UV-VIS-IR absorption and reflection spectroscopy, photoluminescence, and resistivity measurements. Experimental results reveal that as-deposited ZnO:Er films have both high transmittance in the visible range and low electrical resistivity and can be used as efficient transparent conducting oxides (TCOs). These films annealed in the oxidizing atmosphere have a visible emission band which can be used to fabricate light-emitting diodes.     

Effect of annealing on optical and structural properties of ZnS/MnS and MnS/ZnS superlattices thin films for solar energy application

ZnS/MnS super lattice thin films were grown on glass substrates by Chemical Bath Deposition technique. Equimolar aqueous solutions of ZnCl₂:thiourea and MnCl₂·2H₂O:thiourea were taken separately. The substrates were placed vertically in the beakers containing the precursor described above, and the films are deposited at 85 °C for an hour. The as deposited films are annealed at 200 °C for about two hours. X-ray diffractometry method was used to obtain structural characterization. The UV–vis absorption spectrometry was employed to find the optical properties. The refractive-index, dielectric constant, optical conductivity, electrical conductivity and extinction coefficient were determined by various equations based on the data. The valence band and conduction band offset voltages for ZnS/MnS were determined as 0.7 eV and 0.1 eV respectively and for MnS/ZnS were 0.4 eV and 0.3 eV respectively. The band alignment of both superlattice was found to be as Type I.     

Effect of annealing on structural, optical and electrical properties of nanostructured Ge thin films

Ge thin films with a thickness of about 110 nm have been deposited by electron beam evaporation of 99.999% pure Ge powder and annealed in air at 100-500 °C for 2 h. Their optical, electrical and structural properties were studied as a function of annealing temperature. The films are amorphous below an annealing temperature of 400 °C as confirmed by XRD, FESEM and AFM. The films annealed at 400 and 450 °C exhibit X-ray diffraction pattern of Ge with cubic-F structure. The Raman spectrum of the as-deposited film exhibits peak at 298 cm⁻¹, which is left-shifted as compared to that for bulk Ge (i.e. 302 cm⁻¹), indicating nanostructure and quantum confinement in the as-deposited film. The Raman peak shifts further towards lower wavenumbers with annealing temperature. Optical band gap energy of amorphous Ge films changes from 1.1 eV with a substantial increase to ∼1.35 eV on crystallization at 400 and 450 °C and with an abrupt rise to 4.14 eV due to oxidation. The oxidation of Ge has been confirmed by FTIR analysis. The quantum confinement effects cause tailoring of optical band gap energy of Ge thin films making them better absorber of photons for their applications in photo-detectors and solar cells. XRD, FESEM and AFM suggest that the deposited Ge films are composed of nanoparticles in the range of 8-20 nm. The initial surface RMS roughness measured with AFM is 9.56 nm which rises to 12.25 nm with the increase of annealing temperature in the amorphous phase, but reduces to 6.57 nm due to orderedness of the atoms at the surface when crystallization takes place. Electrical resistivity measured as a function of annealing temperature is found to reduce from 460 to 240 Ω-cm in the amorphous phase but drops suddenly to 250 Ω-cm with crystallization at 450 °C. The film shows a steep rise in resistivity to about 22.7 KΩ-cm at 500 °C due to oxidation. RMS roughness and resistivity show almost opposite trends with annealing in the amorphous phase.     

Effects of post-thermal annealing temperature on the optical and structural properties of gold particles on silicon suboxide films

In this work, silicon suboxide (SiO_x) thin films were deposited using a RF magnetron sputtering system. A thin layer of gold (Au) with a thickness of about 10 nm was sputtered onto the surface of the deposited SiO_x films prior to the thermal annealing process at 400 °C, 600 °C, 800 °C and 1000 °C. The optical and structural properties of the samples were studied using scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR) and optical transmission and reflection spectroscopy. SEM analyses demonstrated that the samples annealed at different temperatures produced different Au particle sizes and shapes. SiO_x nanowires were found in the sample annealed at 1000 °C. Au particles induce the crystallinity of SiO_x thin films in the post-thermal annealing process at different temperatures. These annealed samples produced silicon nanocrystallites with sizes of less than 4 nm, and the Au nanocrystallite sizes were in the range of 7-23 nm. With increased annealing temperature, the bond angle of the Si-O bond increased and the optical energy gap of the thin films decreased. The appearance of broad surface plasmon resonance absorption peaks in the region of 590-740 nm was observed due to the inclusion of Au particles in the samples. The results show that the position and intensity of the surface plasmon resonance peaks can be greatly influenced by the size, shape and distribution of Au particles.     

Influence of air annealing on the structural, morphological, optical and electrical properties of chemically deposited ZnSe thin films

Zinc selenide nanocrystalline thin films are grown onto amorphous glass substrate from an aqueous alkaline medium, using chemical bath deposition (CBD) method. The ZnSe thin films are annealed in air for 4 h at various temperatures and characterized by structural, morphological, optical and electrical properties. The as-deposited ZnSe film grew with nanocrystalline cubic phase alongwith some amorphous phase present in it. After annealing metastable nanocrystalline cubic phase was transformed into stable polycrystalline hexagonal phase with partial conversion of ZnSe into ZnO. The optical band gap, E_g, of as-deposited film is 2.85 eV and electrical resistivity of the order of 10⁶-10⁷ Ω cm. Depending upon annealing temperature, decrease up to 0.15 eV and 10² Ω cm were observed in the optical band gap, E_g, and electrical resistivity, respectively.     

Influence of p-GaN annealing on the optical and electrical properties of InGaN/GaN MQW LEDs

Optical and electrical properties of InGaN/GaN multiple quantum wells (MQWs) light emitting diodes (LEDs) annealed in pure O₂ ambient (500 °C) and pure N₂ ambient (800 °C) were systematically investigated. The temperature-dependent photoluminescence measurements showed that high-temperature thermal annealing in N₂ ambient can induce indium clusters in InGaN MQWs. Although the deep traps induced by indium clusters can act as localized centers for carriers, there are many more dislocations out of the trap centers due to high-temperature annealing. As a result, the radiative efficiency of the sample annealed in N₂ ambient was lower than that annealed in O₂ ambient at room temperature. Electrical measurements demonstrated that the LEDs annealed in O₂ ambient were featured by a lower forward voltage and there was an increase of ~41% in wall-plug efficiency at 20 mA in comparison with the LEDs annealed in N₂ ambient. It is thus concluded that activation of the Mg-doped p-GaN layer should be carried out at a low-temperature O₂ ambient so as to obtain LEDs with better performance.     

Influence of annealing temperature on structural,electrical and optical properties of WSi2

WSi₂ polycrystalline films of different thicknesses were prepared by low pressure chemical vapor deposition on silicon wafers, and their crystallization properties were studied as a function of the annealing temperature. Structural measurements were performed by X-ray diffraction, detailing for the first time the phase transition from the amorphous to the hexagonal structure at an annealing temperature 380° C and from hexagonal to tetragonal above 700° C. The electrical sheet resistance showed the same transition temperatures.Optical characterization was performed by spectroscopic ellipsometry, and the real and imaginary part of the complex refractive index were obtained as a function of the annealing temperature in the 0.25–0.9 m wavelength range. A broad optical band was found for samples annealed up to 700° C, while for higher annealing temperatures a transparency region for wavelengths greater than 0.5 m and some significant structures appear. A corresponding behavior was observed in the infrared reflectance spectra. Furthermore, it was shown that the determination of the thickness of SiO₂ grown on WSi₂ requires a multilayer model, taking into account the transparency of tetragonal WSi₂.     

Effect of post-thermal annealing on the structural and optical properties of ZnO thin films prepared from a polymer precursor

ZnO thin films were synthesised by a new method which uses polyvinyl alcohol (PVA) as the polymer precursor. The films are annealed at different temperatures and for different annealing times. The structural parameters, like grain size, lattice constants, optical band gap, and Urbach energy, depend on the annealing temperature and time. All the films possess tensile strain, which relaxes as the annealing temperature and time increase. The photoluminescence (PL) spectra contain only ultraviolet (UV) peaks at low temperature, but as the annealing temperature and time increase, we observe peaks at the blue and green regions with a variation in the intensities of these peaks with annealing temperature and time.     

Effect of post-thermal and optical properties annealing on the structural of ZnO thin films prepared from a polymer precursor

ZnO thin films were synthesised by a new method which uses polyvinyl alcohol （PVA） as the polymer precursor. The films are annealed at different temperatures and for different annealing times. The structural parameters, like grain size, lattice constants, optical band gap, and Urbach energy, depend on the annealing temperature and time. All the films possess tensile strain, which relaxes as the annealing temperature and time increase. The photoluminescence （PL） spectra contain only ultraviolet （UV） peaks at low temperature, but as the annealing temperature and time increase, we observe peaks at the blue and green regions with a variation in the intensities of these peaks with annealing temperature and time.     

Effect of post thermal annealing on the structural and optical properties of ZnO thin films prepared from polymer precursor

ZnO thin films were synthesised by a new method which uses polyvinyl alcohol (PVA) as polymer precursor. The films are annealed at different temperatures and for different annealing times. The structural parameters, like grain size, lattice constants, optical band gap, and Urbach energy, depend on the annealing temperature and annealing time. All the films possess tensile strain which relaxes as the annealing temperature and the annealing time increases. The photoluminescence (PL) spectra contain only ultraviolet (UV) peaks at low temperature, but as the annealing temperature and time increase we observe peaks at blue and green regions with variation of the intensities of these peaks with annealing temperature and annealing time.     

Thermal annealing dependence of some optical properties of plasma-modified porous silicon

The photoluminescence and reflectance of porous silicon (PS) with and without hydrocarbon (CH_x) deposition fabricated by plasma enhanced chemical vapour deposition (PECVD) technique have been investigated. The PS samples were then, annealed at temperatures between 200 and 800 °C. The influence of thermal annealing on optical properties of the hydrocarbon layer/porous silicon/silicon structure (CH_x/PS/Si) was studied by means of photoluminescence (PL) measurements, reflectivity and ellipsometry spectroscopy. The composition of the PS surface was monitored by transmission Fourier transform infrared (FTIR) spectroscopy. Photoluminescence and reflectance measurements were carried out before and after annealing on the carbonized samples for wavelengths between 250 and 1200 nm. A reduction of the reflectance in the ultraviolet region of the spectrum was observed for the hydrocarbon deposited polished silicon samples but an opposite behaviour was found in the case of the CH_x/PS ones. From the comparison of the photoluminescence and reflectance spectra, it was found that most of the contribution of the PL in the porous silicon came from its upper interface. The PL and reflectance spectra were found to be opposite to one another. Increasing the annealing temperature reduced the PL intensity and an increase in the ultraviolet reflectance was observed. These observations, consistent with a surface dominated emission process, suggest that the surface state of the PS is the principal determinant of the PL spectrum and the PL efficiency.     

Annealing temperature effect on the structural, optical and electrical properties of ZnS thin films

Zinc sulfide thin films were prepared on glass substrates at room temperature using a chemical bath deposition method. The obtained films were annealed at temperatures ranging from 100 to 500 °C in steps of 100 °C for 1 h. The films were characterized by X-ray diffraction (XRD), Raman spectroscopy, energy dispersive X-ray analysis (EDX), optical absorption spectra, and electrical measurements. X-ray diffraction analysis indicates that the deposited films have an amorphous structure, but after being annealed at 500 °C, they change to slightly polycrystalline. The optical constants such as the refractive index (n_r), the extinction coefficient (k), and the real (ε₁) and imaginary (ε₂) parts of the dielectric constant are calculated depending on the annealing temperature. Aside from the ohmic characteristics of the I-V curve, a nonlinear I-V curve owing to the Schottky contact is also found, and the barrier heights (?_bn) for Au/n-ZnS and In/n-ZnS heterojunctions are calculated. The conductivity type was identified by the hot-probe technique.     

Effect of annealing on the structural, optical and electrical properties of ZnO thin films by spray pyrolysis

Zinc oxide thin films have been deposited on glass substrates at a substrate temperature of 673 K by spray pyrolysis. The samples are annealed in ambient atmosphere at various temperatures. The effect of annealing on structural, electrical, and optical properties of ZnO films has been investigated. X-ray diffraction patterns show that crystallinity of the ZnO films has been improved after annealing. The morphology of ZnO thin films is studied by atomic force microscopy. The tensile strain (compressive stress) is found to decrease with increase in annealing temperature which indicates the relaxation of tensile strain in ZnO thin films. A decrease in energy band gap is observed with increase of annealing temperature. The mechanism of blue-green luminescence of ZnO thin film has been analyzed. The resistivity is found to decrease with annealing temperature.     

Effect of GZO thickness and annealing temperature on the structural,electrical and optical properties of GZO/Ag/GZO sandwich films

The GZO/Ag/GZO sandwich films were deposited on glass substrates by RF magnetron sputtering of Ga-doped ZnO (GZO) and ion-beam sputtering of Ag at room temperature. The effect of GZO thickness and annealing temperature on the structural, electrical and optical properties of these sandwich films was investigated. The microstructures of the films were studied by X-ray diffraction (XRD). X-ray diffraction measurements indicate that the GZO layers in the sandwich films are polycrystalline with the ZnO hexagonal structure and have a preferred orientation with the c-axis perpendicular to the substrates. For the sandwich film with upper and under GZO thickness of 40 and 30 nm, respectively, it owns the maximum figure of merit of 5.3 × 10⁻² Ω⁻¹ with a resistivity of 5.6 × 10⁻⁵ Ω cm and an average transmittance of 90.7%. The electrical property of the sandwich films is improved by post annealing in vacuum. Comparing with the as-deposited sandwich film, the film annealed in vacuum has a remarkable 42.8% decrease in resistivity. The sandwich film annealed at the temperature of 350 °C in vacuum shows a sheet resistance of 5 Ω/sq and a transmittance of 92.7%, and the figure of merit achieved is 9.3 × 10⁻² Ω⁻¹.     

退火对ZnS/PS复合体系光致发光特性的影响

用脉冲激光沉积(PLD)技术以多孔硅(PS)为衬底生长了ZnS薄膜,分别测量了ZnS、PS以及ZnS/PS复合体系在室温下的光致发光(PL)光谱。结果发现,ZnS/PS复合体系的PL光谱中PS的发光峰位相对于新制备的PS有所蓝移。把该ZnS/PS样品分成三块,在真空400℃分别退火10,20,30 min,研究不同退火时间对ZnS/PS复合体系光致发光特性的影响。发现退火后样品的PL光谱中都出现了一个新的绿色发光带,归结为ZnS的缺陷中心发光。随着退火时间的延长,PS的发光强度逐渐降低且峰位红移。把ZnS的蓝、绿光与PS的红光相叠加,整个ZnS/PS复合体系在可见光区450~700 nm形成一个较宽的光致发光谱带,呈现较强的白光发射。