首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
基于伽利略结构的二级激光扩束系统的设计   总被引:1,自引:1,他引:1  
郑盼  杨应平  郜洪云  陶艳 《应用光学》2008,29(3):347-350
针对高倍率扩束系统设计要求(即轴上和轴外像差都得到较好的校正),从三级像差理论出发,设计了一种新型的40×高倍率激光扩束系统。该系统是基于简单的伽利略结构并通过二级扩束系统来实现的,系统包括4片透镜,通过引入2个二次非球面、 2个反射镜或1个棱镜来折叠光路。利用CODE V光学设计软件给出了该系统的光学结构参数和外形结构图,并进行了像质评价。结果表明:该系统结构简单,设计难度小,成本较低,像质好,性能优良,是一种可以被广泛采用的高倍率激光扩束系统。  相似文献   

2.
We propose an on-axis microscope optical system to implement programmable optical Fourier transform image processing operations, taking advantage of phase and polarization modulation of a liquid crystal on silicon (LCOS) display. We use a Hamamatsu spatial light modulator (SLM), free of flickering, which therefore can be tuned to fully eliminate the zero order component of the encoded diffractive filter. This allows the realization of filtering operation on axis (as opposed to other systems in the literature that require operating off axis), therefore making use of the full space bandwidth provided by the SLM. The system is first demonstrated by implementing different optical processing operations based on phase-only blazed gratings such as phase contrast, band-pass filtering, or additive and substractive imaging. Then, a simple Differential interference contrast (DIC) imaging is obtained changing to a polarization modulation scheme, achieved simply by selecting a different incident state of polarization on the incident beam.  相似文献   

3.
赵保银  吕百达 《物理学报》2008,57(5):2919-2924
提出了用平顶多高斯光束作为理想光束和使用离焦望远镜系统合成轴上平顶光束的一种新方法.在近轴近似下,基于柯林斯衍射积分公式推导出轴上光场和入射光场的解析表达式,并做了物理分析.光束阶数N,平顶长度参数L,平顶中心位置zc和纵向中心空间频率Sc对轴上光强分布的影响用数值计算例做了说明.比较表明,该方法优于文献中使用矩形函数模拟理想光束合成轴上平顶光束的方法. 关键词: 轴上平顶光束 平顶多高斯光束 离焦望远镜系统 傅里叶变换  相似文献   

4.
为了满足机场跑道外来物光电探测系统对高像质、大变倍比、长焦距、小型化变焦镜头的需要,利用Zemax软件设计了一款50 mm~1 000 mm机械变焦镜头。该镜头采用机械补偿变焦结构,采用超低色散镜片来矫正变焦过程中引起的大色差问题,通过评价函数操作数对镜头的结构尺寸以及像质进行优化。通过优化设计,整个系统由28片球面透镜组成,系统总长小于400 mm,MTF在100 lp/mm条件下逼近衍射极限(MTF>0.2),RMS弥散斑半径在中心视场条件下小于5 μm,场曲小于0.1 mm,畸变小于1%,绘制了变倍组与补偿组的运动变化曲线,曲线平滑没有断点。分析结果表明:该系统满足机场跑道外来物探测的实际应用需求,对于大变倍比变焦光学系统设计具有一定的参考意义。  相似文献   

5.
We design and fabricate an integrated optical electric field sensor with segmented electrode for intensive impulse electric field measurement. The integrated optical sensor is based on a Mach-Zehnder interferometer with segmented electrodes. The output/input character of the sensing system is analysed and measured. The maximal detectable electric field range (-75 kV/m to 245kV/m) is obtained by analysing the results. As a result, the integrated optics electric field sensing system is suitable for transient intensive electric field measurement investigation.  相似文献   

6.
为了验证空间光学系统热设计的合理性,利用光-机-热集成的热光学分析技术论证了空间光学系统的热设计方案。首先,阐述了热光学技术的一般方法以及热光学技术与热设计的关系,同时根据空间光学遥感器所处的空间环境和结构特点,应用被动和主动热控技术对空间光学系统进行了热设计。然后,利用有限元方法对热控后的温度场和热弹性变形进行了分析,得出该温度载荷条件下光学元件表面的变形量及刚体位移量,利用Zemike多项式进行了波面拟合。最后,用CodeV光学设计软件计算了热载荷作用下光学系统的传递函数。结果表明,各种工况下全视场范围内光学系统分辨率为50lp时,传递函数均超过0.5,成像良好,能够满足光学设计指标,热设计方案合理可行。  相似文献   

7.
大口径精密表面疵病的数字化检测系统   总被引:6,自引:2,他引:4       下载免费PDF全文
 根据散射光成像原理,采用大小两个视场来获取不同精度的暗背景下的亮疵病图像,设计了完整的数字化表面疵病检测系统。该系统采用多区域自适应阈值分割算法对图像进行分割,然后采用基于等价归并标记方法快速提取疵病的特征参数,最后利用BP神经网络对疵病进行分类。实验结果表明该方法既满足实时性需求,又取得了较好的分类检测效果。  相似文献   

8.
In this paper we are proposing a simple idea based on holography to achieve superresolution. The object is illuminated by three fibers which maintain the mutual coherence between the light waves. The object in-plane rotation along with fiber-based illumination is used to achieve superresolution. The object in a 4f optical system is illuminated by an on-axis fiber to make the central part of the object׳s spectrum to the pass through the limiting square-aperture placed at the Fourier plane and the corresponding hologram of the image is recorded at the image plane. The on-axis fiber is switched off and the two off axis fibers (one positioned on the vertical axis and the other positioned on diagonal) are switched on one by one for each orientation of the object position. Four orientations of object in-plane rotation are used differing in angle by 90°. This will allow the recording of eight holographic images in addition to the one recorded with on-axis fiber. The three fibers are at the vertices of a right angled isosceles triangle and are aligned toward the centre of the lens following the fiber plane to generate plane waves for object illumination. The nine holographic images are processed for construction of object׳s original spectrum, the inverse of which gives the super-resolved image of the original object. Mathematical modeling and simulations are reported.  相似文献   

9.
A new method to improve the resolution of optical imaging systems beyond the classical Rayleigh resolution limit is presented. The technique relies on synthetic aperture generation in three stages. The first one (encoding stage) uses an illumination procedure that combines both on-axis and off-axis illumination beams with different polarization states onto the object. After the imaging system, a second stage (decoding stage) allows the recovering of the encoded spatial-frequency object information by means of an interferometric configuration based on the polarization coding carried out in the previous stage. Finally, a third stage (digital post-processing stage) is used to generate a synthetic aperture that is three times larger than the conventional aperture of the imaging system. The whole process allows us to obtain a superresolved image of the object. Experimental implementation of the approach for a commercial microscope objective is presented.  相似文献   

10.
A novel off-axis pulsed-laser deposition (PLD) system for ferroelectric oxide thin films has been developed. The substrates are mounted "upside-down" and are rotating. The maximum substrate size is 2 inches in diameter. The optical and structural properties of the grown BaTiO3 films are compared to the films produced by an on-axis PLD system. The stoichiometry and thickness were checked with Rutherford backscattering spectrometry (RBS). The crystalline quality and orientation were investigated with X-ray diffraction (XRD) and Rutherford backscattering spectrometry in channeling configuration (RBS/C). Using atomic force microscopy, the rms surface roughness was measured. The BaTiO3 films grown on MgO form a planar optical waveguide. The optical losses and the refractive indices of these waveguides were determined with a prism coupling setup. Films grown on 10᎒ mm2 MgO (100) substrates in on-axis geometry show optical waveguide losses less than 3 dB/cm.  相似文献   

11.
新型三反射光学系统设计   总被引:3,自引:1,他引:2  
随着空间光学技术的发展,对于空间相机地元分辨率的要求越来越高,而且必须具有多光谱成像能力,因此空间相机光学系统的设计要满足视场大和畸变小的要求.本文以共轴三反射光学系统为基础,研究了一种新型的三反射光学系统.该系统不仅中心遮拦小、光学畸变低,而且实现了全色和多光谱CCD的合理排布.设计结果表明:当光学系统的焦距为f=12 000 mm、F数为12、成像谱段位于450~900 nm时,视场角可以达到1.6°,光学系统的线中心遮拦比低于1/3,光学畸变量小于0.5%,在50 lp/mm处调制传递函数优于0.47,成像质量达到衍射极限,可以满足多光谱高分辨率空间相机对地遥感的使用需求.  相似文献   

12.
光电跟踪系统的共轴跟踪控制技术研究   总被引:1,自引:0,他引:1       下载免费PDF全文
为了提高光电跟踪系统的跟踪精度,对其粗跟踪环节的共轴跟踪控制技术进行了研究。介绍了共轴跟踪控制的基本原理,分析了常用非线性卡尔曼滤波算法,并仿真比较了无迹卡尔曼滤波(UKF)和容积卡尔曼滤波(CKF)的位置和速度的预测精度。在此基础上综合UKF和CKF的优点,设计了对延迟的合成位置信号进行处理的双并联滤波器,实现了光电跟踪系统的共轴跟踪控制。利用实测数据仿真实验表明,光电跟踪系统的跟踪精度明显提高。  相似文献   

13.
王基强  苏拾  张健  徐达  张国玉 《应用光学》2018,39(1):117-123
针对氙灯太阳模拟器光电转换效率低、寿命短、辐照强度低,均匀性差等不足,基于LED太阳模拟器光学系统,提出了一种球面阵列LED太阳模拟器光学系统,包括准直光学系统、匀光系统以及光源系统的设计方法。利用同轴透射式光学系统技术设计了双分离结构的准直光学系统, 在分析比较常用匀光系统的性能与组成形式的基础上,阐述积分器与视场光阑的设计过程, 然后基于球面光源的设计思想完成光源系统的设计, 利用LightTools光学设计软件对LED太阳模拟器光学系统进行仿真分析与验证。实验结果表明:球面阵列LED太阳模拟器在工作距离100 mm,输出辐照面积为100 mm×100 mm范围内,其辐照强度大于1 100 W/m2,辐照不均匀度优于3.86%。  相似文献   

14.
提出利用变焦系统设计思想来快速实现复杂航空相机光学系统消热差设计的新方法,基于光学式补偿基础,建立了变焦设计与消热差设计的对应关系模型。设计常温下满足成像质量要求的消色差的良好光学系统;建立多个变焦位置,分别对应于不同的工作温度状态;通过优化设计快速发现材料组合,满足宽工作温度范围内像质均良好的要求。利用该方法设计了一工作于0.45~0.70 m波段,焦距650 mm,F数为5.6,视场为5.5的航空CCD相机光学系统,结果表明系统在-40~60 ℃之间成像均保持良好,调制传递函数下降5%。  相似文献   

15.
Riyopoulos S 《Optics letters》1999,24(11):768-770
It is numerically demonstrated that on-axis current channeling through the use of a photoactive layer or layers in vertical-cavity surface-emitting laser cavities counteracts hole burning and allows single-mode operation at high currents. The photoactive layers act as a variable-resistivity screen whose radial aperture is controlled by the light itself. Absorption of a small fraction of the light intensity suffices for significant on-axis current peaking with minimum efficiency loss and optical mode distortion.  相似文献   

16.
明名  吕天宇  邵亮  王斌 《中国光学》2012,(6):646-651
设计了一种Offner光学系统,用于基于相位差异技术的图像恢复和光学系统波像差的辅助检测。该Offner光学系统采用同轴抛物面反射镜作为Offner反射镜,以高速CCD相机和Shack—Hartmann波前探测器作为接收元件,能完好地消除复色光源在图像恢复过程中带来的色差;设计的RMS波像差小于a/50(A=632.8nm),结构简单,容易实现。利用该系统分别以分辨率板和光纤光源为目标进行了图像恢复实验,经过恢复后的图像分辨率提高了19%。此外,利用该系统,采用相位差异算法解算了系统波像差,并与Shack—Hartmann波前探测器的测量结果进行了比较。比较显示两者的RMS波像差测量值相差5%,证明该系统同样能够进行光学波前检测。  相似文献   

17.
为了提高光电探测设备目标探测与识别的能力,设计了一套可见/中波双波段共口径光学系统。根据实际工程经验总结了一套分段设计、组合优化的光学设计方法,通过合理地分配光焦度,分段选择合适的初始结构,再现了双波段共口径光学系统初始结构的设计过程;结合CodeV和TracePro软件量化了制冷型中波红外探测系统的冷反射现象,并且通过外场试验成像验证了分析结论的正确性。双波段共口径光学系统最大视场达到1.25°,畸变小于0.1%,可以在环境温度?30 ℃~50 ℃下工作,中波红外探测系统实现了100%冷光阑匹配,可见光探测系统可以实现大、小视场的切换,双波段成像系统具有调焦、调光功能。该系统成像质量良好、可加工性好、装配难度小、工程可实施性强。  相似文献   

18.
Drawing on interferometry and Fourier analysis, this paper describes the use of a two-beam thermal lens technique for measuring thermo-optical properties in optical materials. The procedure consists of yield interference patterns deformed by a localized photothermal effect. The photothermal phase shift is locally induced by the pump beam focused on a tested sample located on an on-axis probe beam, which is the first arm of a Mach-Zehnder interferometer. The plane where the effect is localized is imaged onto a CCD camera. Then two interferograms are recorded: one without effect and the other one with the induced photothermal phase. Fourier analysis performed on these interferograms allow us to plot the thermal lens map and, therefore, to estimate thermo-optic constant of Malachite Green in water solution. The method is applied to measure low linear absorptions of a diluted sample of Rhodamine B in water solution at 633 nm, showing that the proposed technique allows to measure photothermal phase shift as low as 3.1 mrad at 8 mW of input power in diluted materials.  相似文献   

19.
Cavity-enhanced absorption spectroscopy (CEAS) has generated much interest in shocktube kinetics studies because of its recent success in achieving improved sensitivity and high time resolution with robust optical alignment. While recent progress demonstrated experimental schemes including off-axis scanned-wavelength approach and on-axis ps-pulsed laser approach, that both successfully suppressed the laser-cavity coupling noise, this paper develops a theoretical model to predict the CEAS sensor performance that can be used as a design tool applicable to more generalized cases. The method models the optical field in the cavity based on the decentered Gaussian beam model, from which the cavity transmission spectrum and the laser-cavity coupling noise can be numerically calculated. The simulation results predict sensor performance for different cavity configurations and laser characteristics, including various degrees of laser-cavity mode-matching, laser linewidths, scanning rates, and cavity filling conditions. Simulation with example wavelengths in the ultraviolet, near-infrared, and mid-infrared showed increasing mode-matched beam waist size for increasing wavelengths. An off-axis alignment scheme was found to be capable of suppressing the coupling noise by two orders-of-magnitude at a moderate laser linewidth of 1?GHz. Coupling noise level on the order of 1e-5 for scanned-wavelength off-axis alignment case with a narrowband mid-infrared laser was obtained by model calculation and agreed with experimental results within acceptable uncertainty range. The developed method can serve to guide future design and optimization of CEAS system in shocktube studies.  相似文献   

20.
红外耦合光学系统设计   总被引:2,自引:2,他引:0       下载免费PDF全文
红外目标模拟器由红外目标图像发生器和投影光学系统组成。该红外光学系统是一个要求与2个导引光学系统的光学技术参数相匹配的长焦距、大视场和具有像方远心光路的中红外光学系统。叙述用于红外目标模拟器的红外耦合光学系统的设计原理,提出它与导引光学系统一起可组成放大倍率M=4.5×的红外投影光学系统,并指出IR CRT产生的图像通过红外投影光学系统可成像在导引接收器上。针对给出的红外耦合光学系统的设计特点和技术要求,光学材料选取硅(Si) 锗(Ge) 硅(Si),采用简单的柯克三片式结构完成光学系统设计。设计评价结果表明,该系统的光学性能和成像质量均满足设计指标要求。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号