嵌段共聚物的微相分离和形态

嵌段共聚物的微相分离行为和形态的研究是当前多相高聚物研究中众所瞩目的研究内容,无论从基础理论和应用实际都有其极为重要的意义,因此在这方面的研究已有不少报道,并日趋深入。 以最简单的嵌段共聚物A—B为例,如聚苯乙烯—聚异戊二烯二嵌段共聚物     

嵌段共聚物／均聚物共混体系的微相分离和形态结构研究

着重介绍嵌段共聚物／均聚物共混体系的微相分离，微胶束的形成，微区的形态结构以及形态的控制。     

聚氧化乙烯-聚苯乙烯-聚氧化乙烯三嵌段共聚物的微相分离与结晶

本工作研究了多分散和单分散聚氧化乙烯-聚苯乙烯-聚氧化乙烯三嵌段共聚物(PEO-PS-PEO)的结晶行为,及这些试样按非晶型嵌段共聚物进行微相分离后再结晶的结晶特点.     

PDMS-MDI-PEG多嵌段共聚物涂层表面微相分离行为研究

采用两步溶液聚合方法合成了一系列聚二甲基硅氧烷(PDMS)-4,4′-二苯基甲烷二异氰酸酯(MDI)-聚乙二醇(PEG)多嵌段共聚物.利用轻敲模式原子力显微镜(AFM)观察了嵌段共聚物的表明形貌,研究了退火、共聚物组成以及PEG分子量和不同的官能团对涂层表面微相分离行为的影响,同时对微相分离行为的形成机理也作了相应的探讨.研究表明,该嵌段共聚物即使在PDMS含量大于50wt%时,涂层表面仍呈现出规整有序的纳米级相分离结构,其中疏水相和亲水相分别由PDMS链段和MDI-PEG组分构成.     

嵌段共聚物的微相分离及其质子交换膜性能

嵌段共聚物由于自身嵌段之间的热力学不相容性,容易发生微相分离而形成质子传导通道,并且采用可控活性聚合的方法可设计合成具有特定拓扑结构嵌段共聚物,使之成为最具潜力的一类质子交换膜材料。本文从用于质子交换膜的嵌段共聚物的微相分离热力学理论出发,分析了影响嵌段共聚物微相分离的各类因素,其中包括磺化度、共聚物拓扑结构、嵌段长度、嵌段序列分布、微观聚集结构以及表面形貌等,并对该领域未来的发展做了展望。     

掺杂嵌段共聚物薄膜的相分离研究

采用Monte Carlo方法结合退火方法研究掺杂非对称两嵌段共聚物薄膜的相分离情况.发现随着掺杂极性粒子浓度的增加,嵌段共聚物薄膜体系由层状相逐渐转化成层状和柱状共混相,最后变成分布均匀的柱状相.当掺杂浓度增加到一定程度时,形成了如六边形(6-fold)、七边形(7-fold)和五边形柱状(5-fold)的相结构;六边形柱状相结构的比例随着浓度增加而增加,七边形(7-fold)和五边形柱状(5-fold)相结构的比例随着浓度增加而减小.同时还讨论了两嵌段共聚物大小与掺杂浓度的关系.     

环氧化聚丁二烯-聚苯乙烯嵌段共聚物对聚苯醚/环氧体系反应诱导相分离行为的影响

采用扫描电镜、光学显微镜和光散射仪研究了环氧化聚丁二烯一聚苯乙烯嵌段共聚物(EBs)对聚苯醚(PPO)/双酚A 型环氧树脂(DGEBA)/4,4二(2,6-二甲基苯胺基)甲烷(DIM-DDM)体系反应诱导相分离行为的影响.实验结果表明,EBS的加入对PPo/DGEBA/DIM-DDM体系反应诱导相分离的演化过程有阻滞作用.随着EBS加入量的增加,体系形成双连续相结构所需的PPO含量范围变宽,而对于相同PPO含量、形成双连续相的体系则相结构尺寸减小.     

环氧化聚丁二烯-聚苯乙烯嵌段共聚物对聚苯醚/环氧体系反应诱导 相分离行为的影响

采用扫描电镜、光学显微镜和光散射仪研究了环氧化聚丁二烯-聚苯乙烯嵌段共聚物(EBS)对聚苯醚(PPO)/双酚A型环氧树脂(DGEBA)/4,4’-二(2,6-二甲基苯胺基)甲烷(DIM-DDM)体系反应诱导相分离行为的影响. 实验结果表明, EBS的加入对PPO/DGEBA/DIM-DDM体系反应诱导相分离的演化过程有阻滞作用. 随着EBS加入量的增加, 体系形成双连续相结构所需的PPO含量范围变宽, 而对于相同PPO含量、形成双连续相的体系则相结构尺寸减小.     

聚苯乙烯溶胀聚苯乙烯－聚丁二烯－聚苯乙烯三嵌段共聚物微区的研究

嵌段共聚物/均聚物共混体系,各嵌段会形成各自的相,并且嵌段间的连接点一定在两相之间的界面上,这一要求极大地影响了嵌段共聚物/均聚物共混体系的链构象和相行为.     

线形苯乙烯-丁二烯-苯乙烯嵌段共聚物(SBS)的粘弹弛豫与相形态

研究了不同温度下苯乙烯-丁二烯-苯乙烯嵌段共聚物(SBS)的粘弹弛豫与相形态. DSC分析发现, SBS的相结构特别是其中质量分数较低的PS相畴的大小受热历史影响显著. 用TEM表征了SBS的双相连续形态和两相相畴尺寸. 用动态流变学方法研究了不同温度下SBS嵌段大分子的松弛行为. 结果表明, 在低于PS相玻璃化转变温度时, 嵌段分子中的PB段已可发生运动; 而当高于PS玻璃化转变温度后, 由于PB与PS间的相互作用及PB的链缠结所限制, 体系仍保持较高的弹性模量, 呈现“第二平台”特征流变行为.     

含聚联烯的三嵌段共聚物的合成

聚联烯由于其特殊的结构而使其具有一些独特的应用,但聚合方法的局限性限制了聚联烯共聚物的研究.合成了一种偶氮-TEMPO（2,2,6,6-四甲基哌啶氮氧自由基）双官能团引发剂,通过苯基联烯醚单体的自由基聚合和苯乙烯的NMRP（氮氧调控自由基聚合）活性聚合,制备了聚苯乙烯-b-聚联烯-b-聚苯乙烯三嵌段共聚物.通过这种机理...     

Effect of Cyclization of Polystyrene/Polyisoprene Block Copolymers on Their Micellar Morphology

Micelles made from linear polystyrene‐block‐polyisoprene (PS/PI) in decane are spherical. The differences in the structure of micelles made from linear and cyclic PS/PI were investigated using small‐angle X‐ray scattering at rest and under shear flow. The effect of shear revealed that micelles made from cyclic copolymer chains have an elongated shape, which was confirmed by transmission electron microscopy. The cyclization of diblock copolymer chains is thus a new method to control the micellar morphology.

     

The Morphology of Symmetric Triblock Copolymer Melts Confined in a Slit: A Monte Carlo Simulation

Monte Carlo simulations based on a modified bond‐fluctuation and vacancy‐diffusion algorithm on a simple cubic lattice were employed to examine the morphology of thin films of the symmetric A_mB_2nA_m triblock copolymer confined between two hard homogeneous parallel walls. The walls preferred either segment A or segment B. Parallel lamellae, parallel cylinders and perpendicular cylinders morphologies, dependent on the composition, film thickness and interaction energies, were identified in these simulations, in agreement with the experimental observations of several researchers.     

苯乙烯-丁二烯-苯乙烯嵌段共聚物负载Pt催化肉桂醛制备肉桂醇的研究

用紫外光交联的方法制备不同交联度的苯乙烯-丁二烯-苯乙烯嵌段共聚物(SBS)负载Pt的催化膜并探讨其对肉桂醛选择性加氢制备肉桂醇的催化效果.其中催化剂Pt纳米簇用微波法制备,XRD测其平均粒径为3.7 nm.膜载催化剂的负载量、光交联剂三羟甲基丙烷三丙烯酸酯(TMPTA)和光引发剂二苯甲酮(BP)的用量均为3%.用色谱-质谱联用、XRD、紫外分光光度计对膜载催化剂和反应产物进行了表征,结果表明,随着交联度的增加,肉桂醇的催化选择性先增后减,紫外光光照80s时,负载膜交联度23.63%,肉桂醛转化率为91.46,肉桂醇选择性80.98%.质谱分析表明交联度大于30%后,催化产物中开始有膜分解产生的小分子杂质出现,并随交联度的进一步增大而增多;显微镜检测同时说明此时膜结构发生变化,造成肉桂醇选择性的降低.     

用透射电镜法研究聚(苯乙烯-异戊二烯)二嵌段共聚物微相分离的微区尺寸

本文采用透射电镜(TEM)法,系统地研究了具有不同组成,不同分子量和不同形态结构的聚(苯乙烯-异戊二烯)二嵌段共聚物,并由TEM照片直接测量具有栓状,层状和有规双连续双金钢石(OBDD)结构的PS-PI二嵌共聚物的微区尺寸,讨论了其与分子量的关系。实验证明嵌段共聚物微相分离有规结构的微区尺寸大小与分子量呈2/3的关系。     

Morphology and Conformation Analysis of Self‐Assembled Triblock Copolymer Melts

Summary: We used the dissipative particle dynamics method to simulate the self‐assembly of symmetric triblock copolymers of the type ABA. Depending on the volume fraction of the end blocks f_A, several mesophases including lamellar, perforated lamellar, gyroid, hexagonal cylinders and bcc spherical micelles were obtained. The order‐disorder transition (ODT) at f_A = 0.5 was found to be about χN = 19.8. The ODT for the cylindrical mesophase at symmetrical points on the phase diagram had different values, indicating asymmetry in the phase diagram. We were also able to estimate the bridge fraction in the different mesophases. They range from about 0.44 for the lamellar mesophase to about 0.75 for the spherical micelles. Our simulation results are in good agreement with previously reported theoretical calculations and experimental observations.

The hexagonal cylinders generated with the A₆B₄A₆ copolymer.     

Influence of Phase Separation Behaviour on Toughness of Compression Moulded SBS Star Block Copolymer/Polystyrene Blends

The influence of homopolymer molecular weight and compression moulding on morphology formation and deformation behaviour of binary blends of polystyrene-polybutadiene based star block copolymer and polystyrene (PS) homopolymer was investigated. The samples used were a polystyrene-(polystyrene-co-polybutadiene)-polystyrene (S-S/B-S) star block copolymer and anionically prepared polystyrene (aPS). The techniques used were transmission electron microscopy (TEM) and uniaxial tensile testing. A wide range of segregation behaviour was observed depending on the ratio of the length of aPS chains relative to that of corresponding outer blocks of the block copolymer. For the first time, the formation of macrophase-separated ‘droplet-like’ morphology has been reported, which endows the block copolymer/polystyrene blends with higher toughness. The mechanical properties of blends are discussed in the light of micromechanical processes of deformation. The micromechanical mechanisms and their dependence with inter domain distance are similar to the mechanisms found in rubber network toughened systems.