Property study of Si + -ion-implanted Nd:YVO 4 waveguides

Planar waveguides were formed in Nd:YVO₄ crystals by 3.0-MeV Si⁺-ion implantation at doses of 1×10¹³–1.5×10¹⁵ ions/cm² at room temperature. The effective refractive indices of the waveguide propagation modes were measured by using a prism-coupling method. It was found that the number of the propagation modes is dependent on the doses for the waveguides in Nd:YVO₄. The atom displacement in the near-surface region (about 2 μm beneath the surface) of the Nd:YVO₄ crystal induced by the implantation was simulated by using the TRIM 98 (transport and range of ions in matter) code. The possible reasons for the waveguide formation are discussed in a primary way. Received: 17 July 2002 / Revised version: 20 September 2002 / Published online: 11 December 2002 RID="*" ID="*"Corresponding author. Fax: +86-531-8565167, E-mail: drfchen@sdu.edu.cn     

Optical Waveguide Formed in RbTiOPO4 Crystal by 6.0 MeV O^3＋ Implantation

A planar optical waveguide was formed in RbTiOP04 crystal by 6.0-MeV oxygen ion implantation with the dose of 2 × 10^15 ions/cm2 at room temperature. Annealing at 200℃ for 30min in air is performed to improve the thermal stability of the waveguide. The dark modes of the waveguide are measured at wavelengths 633 and 1539 nm, respectively. The refractive index profiles in the guiding layer are reconstructed by using the reflectivity calculation method. TRIM＇98 code was carried out to simulate the damage profiles caused by the implantation process to obtain a better understanding of the waveguide formation.     

Characterization of optical waveguide in Nd: GdVO4 by triple-energy oxygen ion implantation

We report on the optical planar waveguide formation and modal characterization in Nd: GdVO₄ crystals by triple oxygen ion implantation at energies of (2.4, 3.0, and 3.6 MeV) and fluences of (1.4, 1.4, and 3.1)  × 10¹⁴ions/cm². The prism-coupling method is used to investigate the dark-mode property at wavelength of 632.8 nm. The refractive index profiles of the waveguide are reconstructed by an effective refractive index, n_eff method. The modal analysis shows that the fields of TE modes are well restricted in the guiding region, which means the formation of nonleaky waveguide in the crystal.     

Characterization of optical waveguide in Nd: LuVO4 crystals by triple-energy oxygen ion implantation

We report on the optical planar waveguide formation and modal characterization in Nd:LuVO₄ crystals by triple-energy O³⁺-ion implantation at energies of 2.4, 3.0, and 3.6 MeV and doses of 1.4, 1.4, and 3.1×10¹⁴ ions/cm², respectively. The prism-coupling method is used to investigate the dark-mode property at a wavelength of 633 nm. The refractive index profiles of the waveguide are reconstructed by the reflectivity calculation method (RCM). The modal analysis shows that the fields of TE modes are well restricted in the guiding region, which indicates the formation of non-leaky waveguide in the crystal.     

Analysis and Determination of Refractive Index Profiles of O^2＋ Ion-Implanted LiNbO3 Planar Waveguide Using Etching and Ellipsometry Techniques

The refractive index profiles of 3 MeV O^2＋ ion-implanted planar waveguides in lithium niobate are reconstructed based on etching and ellipsometry techniques. SRIM2003 code is used to simulate the damage distribution in waveguide. It is demonstrated that the index profile of this kind of waveguide, extending to several micrometres in depth, can be determined by etching in combination with following ellipsometric measurements. A good agreement is found between the simulated damage distributions in waveguide and the index profiles based on experimental data, and the width of refractive index barrier is wider than the result of SRIM2003.     

Ti:sapphire rib channel waveguide fabricated by reactive ion etching of a planar waveguide

We report, to our knowledge, the first active channel waveguide in Ti:sapphire. We have created ∼1.4-μm high ribs in a ∼10-μm thick Ti:sapphire planar waveguide by reactive ion etching. Following excitation by an Ar-ion laser, the rib structure showed channel-waveguide fluorescence emission. The mode profiles and the beam-parameter values (M²) were measured. The coupling efficiency of fluorescence emission into a single-mode fiber was an order of magnitude higher than for fluorescence from unstructured planar regions of the waveguide. Such devices are of interest as low-threshold tunable lasers and as broadband light sources in low-coherence interferometry. Received: 22 December 2002 / Revised version: 30 March 2002 / Published online: 8 August 2002     

Optical properties of dye-doped zirconia films by spectroscopic ellipsometry

The optical properties of zirconia films doped with rhodamine 6G and oxazine 725 by the sol-gel process were investigated using spectroscopic ellipsometry (SE). Accurate refractive index n and the extinction coefficient k were determined using a three-oscillator classical Lorentz model in the wavelength range of 300-800 nm. The derived refractive index of dye-doped films exhibited anomalous dispersion in the absorption region. Wavelength tunable output lasing action yellow and near-infrared wavelength region was achieved by DFB configuration using zirconia films doped with R6G and oxazine 725.     

Proposals for Fabrication of Long-Period Grating in LiNbO3 Strip Waveguides

The structure of a strip LiNbO3 waveguide clad with a planar LiNbOa waveguide is proposed to fabricate a long-period waveguide grating （LPWG）. It is shown theoretically that an LPWG device based on such a special LiNbOa waveguide structure is of the merit of thermal stability. The methods for fabrication of planar waveguide, channel waveguide and grating are suggested and discussed. Detailed design consideration is exemplified based on a soft-proton-exchange planar waveguide clad Ti-diffused LiNbOa （Z-cut） strip waveguide.     

Characteristics of Nd：GdVO4 Laser with Different Nd-Doping Concentrations

We report the properties of a compact diode-pumped continuous-wave Nd：GdV04 laser with a linear cavity and different Nd-doped laser crystals. In a 0.2at.% Nd-doped Nd：GdVO4 laser, 1.54 W output laser power is achieved at 912nm wavelength with a slope efficiency of 24.8% at an absorbed pump power of 9.4W. With 0.3at.% Nd-doping concentration, we can obtain the either single-wavelength emission at 1064nm or 912nm or the dual-wavelength emission at 1064nm and 912nm by controlling the incident pump power. From an incident pump power of 11.6 W, the 1064nm emission between ^4Fa/2 and ^4I11/2 is suppressed completely by the 912nm emission between ^4Fa/2 and ^4I9/2. We obtain 670 mW output of the 912nm single-wavelength laser emission with a slope efficiency of 5.5% by taking an incident pump power of 18.4 W. Using a Nd：GdV04 laser with 0.4at.% Nd-doping concentration, we obtain either the single-wavelength emission at 1064nm or the dual-wavelength emission at both 1064nm and 912nm by increasing the incident pump power. We observe a strong competition process in the dualavelength laser.     

Well-confined Yb:GdVO4 laser waveguide formed by MeV C ion implantation

The planar waveguide in x-cut Yb:GdVO₄ crystal has been fabricated by 6.0 MeV carbon ion implantation with the fluence of 1 × 10¹⁴ ions/cm² at room temperature. The modes of the waveguide were measured by the prism-coupling method with the wavelength of 633 nm and 1539 nm, respectively. An enhanced ordinary refractive index region was formed with a width of about 4.0 μm beneath the sample surface to act as a waveguide structure. By performing a modal analysis on the observed transverse magnetic polarized modes, it was found that all the transverse magnetic polarized modes can be well-confined inside the waveguide. Strong Yb-related photoluminescence in Yb:GdVO₄ waveguide has been observed at room temperature, which reveals that it exhibits possible applications for integrated active photonic devices.     

Negative Refraction in One-Dimensional Photonic Crystals with Tilted Interface

We investigate the wave propagation through the tilted interface of one-dimensional photonic crystals. Negative refraction can be realized by excitation of the Bloch states in the extended Brillouin zone with suppressed reflection. Equi-frequency surface analysis shows that the positive refraction, negative refraction or birefringence in this configuration can be achieved under a proper incident angle, which is confirmed by finite-difference timedomain simulations. The results may be useful in applications in the new devices based on one-dimensional photonic or optical waveguide arrays.     

Multimode-Waveguide-Based Optical Power Splitters in Glass

Low-loss glass-based buried multimode waveguides are fabricated by using the field-assisted Ag＋-Na＋ ionexchange technique, and multimode optical power splitters are investigated. The measured loss of the multimode waveguides is lower than 0.1 dB/cm, and the additional loss of the multimode optical power splitters is lower than 1.3 dB under the uniform splitting condition.     

Polarized Emission of an Eu^3＋ Doped Azo-Polymer Waveguide

We investigate the polarized emission behaviour of an Eu^3 doped azo-polymer waveguide. Affected by the azobenzene groups in the photoinduced orientation process by the 532nm linearly polarized laser, the ligands were realigned orderly perpendicular to the direction of the orientation direction. This leads to the polarized absorption and emission of the waveguide in the orientation direction. By an m-line apparatus based on the prism coupling technique, two guided propagation modes were observed in the waveguide, and the refractive index at 650hm in TE polarizations is 1. 7505.     

Broadband Infrared Luminescence of Ni^2＋ in Petalite-Type Transparent Glass Ceramics

Transparent Ni^2＋-doped magnesium aluminosilicate glass ceramics are prepared. The formation of petalite-type crystallites in the glass ceramics is confirmed by x-ray diffraction. Broadband infrared luminescence centred at around 1235nm with full width at half maximum （FWHM） of about 300nm is observed from the Ni^2＋-doped glass ceramics. The observed infrared emission could be attributed to the ^3T2（F） → ^3A2（F） transition of octahedral Ni^2＋ ions in petalite-type crystallites. Theproduct of the fluorescence lifetime and the stimulated emission cross sections is 1.2 ×10-24 cm^2s.     

Spectroscopic properties of Tm -doped Ba3Gd2(BO3)4 crystal

crystal with the size up to Φ 13 mm×44 mm was grown successfully by the Czochralski technique and its optical properties were presented. The absorption cross-section and emission cross-section were presented. Also, the potential laser gain near 1.9 μm was investigated. In the framework of the Judd-Ofelt (J-O) theory, the intensity parameters were calculated to be: Ω₂=11.375×10⁻²⁰ cm², Ω₄=5.077×10⁻²⁰ cm² and Ω₆=6.524×10⁻²⁰ cm². The spectroscopic parameters of this crystal such as the oscillator strengths, radiative transition probabilities, radiative lifetime as well as the branching ratios were calculated, too. This crystal is promising as a tunable infrared laser crystal.     

Optical waveguide engraving in a LiNbO3 crystal fiber

This paper reports the engraving of an optical waveguide inside a LiNbO₃ crystal fiber via the photorefractive effect and an optical vortex. Afterwards this waveguide was successfully tested and its properties evidenced.     

An He-implanted optical planar waveguide in an Nd:YGG laser crystal preserving fluorescence properties

We report the formation of a planar waveguide in an Nd:YGG laser crystal by low-energy He-ion implantation at liquid nitrogen temperature (77 K). The optical properties are measured by the prism coupling and end-face coupling methods, the absorption properties the waveguide and Nd:YGG substrate are obtained. The fluorescence spectrums are investigated by confocal methods. The experimental results revealed that the planar waveguide preserved the absorption and fluorescence properties of the Nd:YGG laser crystal. Thus, the planar waveguide formed by the ion implantation method is a promising candidate in waveguide lasers.     

Cs^＋-K^＋ Exchange in Z-Cut KTiOPO4 Crystal Covered with Chromium Masking Layer

Cs^＋-K^＋ ion exchanges are performed on z-cut KTiOPO4 crystals with chromium coating covered. The temperature of ion exchange is 430℃, and the time range from 15min to 30min. The dark mode spectra of the samples are measured by the prism coupling method. The channel structures on the samples are observed by a microscope and the near field pattern of the channel waveguides are measured by the end-fire coupling method. The refractive index of the samples increases and the increments at surface are modulated due to the existence of Cr film. In the region covered by Cr film, the refractive index of the samples at the surface increases dramatically in a shallow layer. The results of energy dispersive x-ray spectra indicate that in the region covered with Cr film, Cr ions participate in the ion exchange process, and enhance the refractive index. The results may provide a possibility that achieves index enhancement and Cr doping synchronically.     

Upconversion studies in Er doped TeO2-M2O (M=Li, Na and K) binary glasses

The luminescence properties of Er³⁺ doped alkali tellurite [ TeO₂-M₂O (M=Li, Na and K)] glasses are investigated. Infrared to visible upconversion emissions are observed at 410, 525, 550 and 658 nm using 797 nm excitation. These bands are assigned to the ²H_9/2  →⁴I_15/2, ²H_11/2  →⁴I_15/2, ⁴S_3/2  →⁴I_15/2, ⁴F_9/2  →⁴I_15/2 transitions of Er³⁺ respectively. Detailed study reveals that the ²H_9/2  →⁴I_15/2 transition at 410 nm involves a three-step process while the other transitions involve two-steps. Excitation with 532 nm radiation gives additional bands at 380, 404, 475 and 843 nm wavelengths due to the ⁴G_11/2  →⁴I_15/2, ²P_3/2  →⁴I_13/2, ²P_3/2  →⁴I_11/2, and ⁴S_3/2  →⁴I_13/2 transitions, respectively, along with the bands observed on NIR excitation. The fluorescence yield is found to be largest for the TeO₂-Na₂O glass. The lifetime of the ⁴S_3/2 level has been measured for all the three cases and used to explain the upconversion mechanisms. The fluorescence intensity ratio corresponding to the two thermally coupled levels (²H_11/2, ⁴S_3/2) has been used to estimate the temperature of the glass. It is observed that the temperature sensing capacity of TeO₂-Li₂O glass is better than the other two glasses.     

Tunable Infrared Luminescence and Optical Amplification in PbS Doped Glasses

PbS-doped glasses are prepared. Absorption and luminescence spectra show that both the absorption and infrared emission can be tuned widely by thermal treatment conditions. Optical amplification at 1300 nm is observed, and amplified spontaneous emission （ASE） spectrum is also measured to confirm the optical gain from PbS quantum dots.