石墨烯修饰玻碳电极测定邻苯二酚

制备了用于测定邻苯二酚(CAT)的石墨烯修饰电极,并应用循环伏安法研究了CAT在该修饰电极上的电化学行为;用差分脉冲伏安法研究了测试底液的pH值对该修饰电极性能的影响,结果表明,此修饰电极在含不同浓度CAT的PBS溶液(pH=7.0)中测定,响应电流与CAT浓度在5.0×10-8～5.6×10-4mol/L范围内有良好的线性关系,相关系数r=0.9919,检出限为6.68×10-9mol/L(S/N=3)。与其它几种修饰电极相比,石墨烯修饰电极制备简单、响应时间快、操作简便,稳定性和重现性良好,有应用价值。     

间苯二酚在TiO2-石墨烯修饰玻碳电极上的电化学行为及测定

制备了TiO2-石墨烯修饰玻碳电极。用循环伏安法(CV)和差分脉冲伏安法(DPV)对间苯二酚在该修饰电极的电化学行为进行了研究。实验结果表明,在pH值为6.0的磷酸盐缓冲液(PBS)中,该修饰电极对间苯二酚具有良好的电催化作用。对TiO2-石墨烯用量、支持电解质、pH和扫描速度等实验条件进行了优化。在优化条件下,利用DPV测定,间苯二酚的氧化峰电流与其浓度在1.0×10-6～1.0×10-4mol/L范围内呈良好的线性关系,线性相关系数为0.995。检出限为2×10-7mol/L。将该方法应用于模拟水样中间苯二酚的测定,回收率为96.5～104.2%。     

聚三聚氰胺-石墨烯复合膜修饰电极对多巴胺与尿酸的同时测定

采用循环伏安法制备了聚三聚氰胺-石墨烯复合膜修饰电极(poly-(MA)-ERGO/GCE)。研究了抗坏血酸(AA)、尿酸(UA)和多巴胺(DA)在该修饰电极上的电化学行为。结果表明,该修饰电极对AA、UA和DA均有良好的电化学响应,且三者的氧化峰在该修饰电极上可完全分离。据此建立了在大量AA存在下同时测定UA和DA的新方法。在优化条件下,微分脉冲伏安法(DPV)测定UA和DA的线性范围均为1.0×10~(-8)~5.0×10-6mol·L~(-1),检出限(3sb)均为5.0×10~(-9)mol·L~(-1)。     

氧化石墨烯/铁氰化铈修饰玻碳电极同时测定扑热息痛和咖啡因

采用滴涂法和电沉积法制备了氧化石墨烯/铁氰化铈(CeFe(CN)6)纳米复合膜修饰玻碳电极。用扫描电镜对氧化石墨烯和氧化石墨烯/CeFe(CN)6纳米复合膜进行了表征。分别用循环伏安法和差分脉冲伏安法研究了扑热息痛和咖啡因在修饰电极上的电化学行为。结果表明,在0.1 mol/L醋酸盐缓冲溶液(pH5.0)中,扑热息痛和咖啡因在此修饰电极上具有良好的电化学行为,扑热息痛和咖啡因分别在1.0×10-7～6.0×10-5mol/L和1.0×10-6～1.3×10-4mol/L浓度范围内与电化学响应信号呈良好的线性关系,相关系数分别为0.990和0.992;信噪比为3时,扑热息痛和咖啡因检出限分别为5.0×10-8mol/L和5.2×10-7mol/L。将本方法用于人尿样品分析,回收率为96.1%～105.4%。     

石墨烯修饰玻碳电极伏安法测定酪氨酸

制备了石墨烯修饰玻碳电极,研究了酪氨酸在修饰电极上的电化学行为.优化了包括支持电解质、溶液pH、修饰剂用量、富集电位及时间等测定条件.在0.1 mol·L-1pH 7.0的磷酸盐缓冲溶液中,峰电流与酪氨酸的浓度在3×10-6～1.2×10-4mol·L-1的范围内呈良好的线性关系,检出限为2 × 10-7 mol·L-...     

单分子层γ-氨基丁酸共价修饰玻碳电极同时测定多巴胺、尿酸和抗坏血酸

采用电氧化法制备了一种新型γ-氨基丁酸(ABA)修饰的玻碳电极.X射线光电子能谱(XPS)和循环伏安法研究表明,ABA以单分子层状态以C—N键牢固地共价键合在电极表面.该修饰电极对多巴胺(DA)、尿酸(UA)和抗坏血酸(AA)都具有良好的电化学催化特性.在pH=7.0磷酸缓冲溶液中,DA,UA和AA分别于0.45,0.25和0.07V(vs.Ag/AgCl)有一个良好的、独立的阳极方波伏安峰,表明此修饰电极可用于这3种物质的同时测定.与DA,UA和AA的方波伏安峰电流呈线性关系的浓度范围分别为4.0～400,2.0～500和1.0～600μmol/L,检测限(3δ)分别为1.6,1.2和0.8μmol/L.该修饰电极具有良好的灵敏度、选择性和稳定性,并具有抗污染能力.     

钯-氧化锌纳米管修饰电极同时检测多巴胺、抗坏血酸和尿酸

以PdCl₂和Zn(Ac)₂为起始物,采用静电纺丝方法结合高温煅烧,成功制备了钯-氧化锌(Pd-ZnO)中空纳米管。Pd的存在改善了ZnO晶体颗粒的均匀性,调控纤维向中空管状结构转变。利用扫描电子显微镜、透射电子显微镜、X射线衍射等表征技术证明了纳米管内径为240 nm,Pd纳米粒子粒径约为80 nm,且在纳米管上均匀分布。X射线光电子能谱证明,Pd纳米粒子主要以PdO形态存在。所得的Pd-ZnO修饰玻碳电极对多巴胺(DA)、抗坏血酸(AA)和尿酸(UA)均显示出良好的催化活性。采用差分脉冲伏安法测定含DA、AA和UA的混合液,三者的氧化峰电位在此修饰电极上可完全分离,对应的线性范围分别为3.0×10^-7～3.0×10^-5 mol/L(R²=0.9967)、1.0×10^-5～1.0×10^-3 mol/L(R²=0.9991)和6.0×10^-6～6.0×10^-4 mol/...     

氧化石墨烯修饰碳离子液体电极同时测定鸟嘌呤和腺嘌呤

以离子液体1-丁基-3-甲基咪唑六氟磷酸盐为粘合剂制备了碳糊电极,然后将氧化石墨烯滴涂到碳糊电极表面制成了一种新型的氧化石墨烯修饰碳离子液体电极。研究了鸟嘌呤和腺嘌呤在修饰电极上的电化学行为。实验结果表明,在0.1 mol/L醋酸盐缓冲溶液中(pH4.5),鸟嘌呤和腺嘌呤在该修饰电极上具有良好的电化学行为,在2.0×10-7～1.5×10-5mol/L浓度范围内鸟嘌呤和腺嘌呤的浓度在该电极上与电化学响应信号呈良好的线性关系,相关系数分别为为0.992和0.996。信噪比为3时,检出限为1.0×10-8mol/L。     

血红蛋白在TiO2-石墨烯/离子液体/壳聚糖纳米复合膜修饰电极上的直接电化学

基于TiO2-石墨烯、离子液体和壳聚糖复合膜修饰玻碳电极制备了一种新型的电化学传感器。用循环伏安法研究了血红蛋白在该修饰电极上的直接电化学行为。结果表明,该纳米复合膜能有效地促进血红蛋白在电极上的直接电子转移,保持其生物催化活性。该传感器对H2O2具有良好的催化性能。H2O2的电流响应信号与其浓度在20～860μmol/L范围内呈良好的线性关系,检出限为0.1μmol/L(S/N=3)。传感器具有良好的稳定性和重现性。     

金纳米粒子-石墨烯修饰玻碳电极的制备及对多巴胺、抗坏血酸和尿酸的同时检测

采用三步法制备了金纳米粒子-石墨烯层层组装的复合材料,并将其修饰在玻碳电极上,制备成一种新型的同时检测抗坏血酸(AA)、多巴胺(DA)和尿酸(UA)的电化学传感器。采用扫描电子显微镜(SEM)对复合材料进行了表征,并研究了传感器对AA、DA、UA电催化性能。结果表明:该传感器对AA、DA和UA的氧化具有很好的催化和分离效果,可实现AA、DA和UA的同时测定。在三者共存体系中,AA-DA、DA-UA、AA-UA的氧化峰电位差分别为152mV、161mV和313mV。线性范围分别为1.996×10-5~5.580×10-3、1.996×10-6~5.478×10-3和1.000×10-6~1.000×10-3 mol/L,检出限分别为1.200×10-5、1.030×10-7和4.100×10-7 mol/L。该修饰电极选择性好、稳定性高,有望用于实际样品中AA、DA和UA的同时检测。     

聚钙羧酸修饰玻碳电极差分脉冲伏安法同时测定多巴胺和尿酸

采用电化学方法将钙羧酸(CCA)聚合修饰在玻碳电极(GCE)表面制备了聚钙羧酸指示剂修饰玻碳电极(PCCA/GCE),并用循环伏安法和交流阻抗法研究了电极的电化学性能。结果表明:在pH 6.0的磷酸盐缓冲溶液中,多巴胺(DA)和尿酸(UA)在聚钙羧酸修饰电极上的氧化峰得以分开,峰电位差为0.14V,据此提出了聚钙羧酸修饰电极差分脉冲伏安法同时测定多巴胺和尿酸的方法。DA和UA的浓度分别在5.0～43.8μmol.L-1和5.0～50.0μmol.L-1范围内与其氧化峰电流呈线性关系,检出限(3S/N)分别为0.2μmol.L-1和0.5μmol.L-1。方法可用于多巴胺注射液样品中DA和UA的测定,测定值的相对标准偏差(n=5)依次为2.43%和2.35%。     

Electrocatalytic Oxidation and Simultaneous Determination of Uric Acid,Xanthine, Hypoxanthine and Dopamine Based on β-Cyclodextrin Modified Glassy Carbon Electrode

A novel covalently modified glassy carbon electrode with β-cyclodextrin was prepared via electropolymerization technique for the simultaneous determination of uric acid(UA), xanthine(XA), hypoxanthine(HX) and dopamine(DA). This new electrode presented an excellent electrocatalytic activity towards the oxidation of UA, XA, HX and DA by cyclic voltammetry(CV) method. The oxidation peaks of the four compounds were well defined and had the enhanced peak currents. The separation potentials of the oxidation peaks for DA-UA, UA-XA and XA-HX were 150, 390 and 360 mV in CV, respectively. By means of differential pulse voltammetry(DPV) method, the calibration curves in the ranges of 10-225, 5-105, 10-170 and 5-150 μmol/L were obtained for UA, XA, HX and DA, respectively. The lowest detection limits(S/N=3) were 5, 1.25, 5 and 1.5 μmol/L for UA, XA, HX and DA, respectively. The practical application of the modified electrode was demonstrated by the determination of DA in hydrochloride injection and UA, XA, HX in human urine samples.     

Synergistic Effect of Graphene and Multiwalled Carbon Nanotubes on a Glassy Carbon Electrode for Simultaneous Determination of Uric Acid and Dopamine in the Presence of Ascorbic Acid

A poly(diallyldimethylammonium chloride)-graphene-multiwalled carbon nanotube modified glassy carbon electrode was fabricated and evaluated by cyclic voltammetry and differential pulse voltammetry. The modified electrode offered high sensitivity, selectivity, excellent long-term stability, and electrocatalytic activity for uric acid and dopamine. This sensor showed wide linear dynamic ranges of 5.0 to 350.0 µmol L^?1 for uric acid and 10.0 to 400.0 µmol L^?1 for dopamine in the presence of 500 µmol L^?1 ascorbic acid. The limits of detection were 0.13 for uric acid and 0.55 µmol L^?1 for dopamine. This functionalized electrode has potential application in bioanalysis and biomedicine.     

Chitosan Incorporating Cetyltrimethylammonium Bromide Modified Glassy Carbon Electrode for Simultaneous Determination of Ascorbic Acid and Dopamine

Simultaneous determination of a neurotransmitter, dopamine (DA), and ascorbic acid (AA) is achieved at neutral pH on a chitosan incorporating cetyltrimethylammonium bromide (CTAB) modified glassy carbon (GC) electrode. Differential pulse voltammetry (DPV) technique was used to investigate the electrochemical response of DA and AA at a glassy carbon electrode modified with chitosan incorporating CTAB. An optimum 6.0 mmol L^?1 of CTAB together with 0.5 wt% of chitosan was used to improve the resolution and the determination sensitivity. In 0.1 mol L^?1 aqueous phosphate buffer solution of pH 6.8, the chitosan‐CTAB modified electrode showed a good electrocatalytic response towards DA and AA. The anodic peak potential of DA shifted positively, while that of AA shifted negatively. Thus, the difference of the anodic peaks of DA and AA reached 0.23 V, which was enough to separate the two anodic peaks very well. The presented method herein could be applied to the direct simultaneous determination of DA and AA without prior treatment. The anodic peak currents (I_pa) of DPV are proportional to DA in the concentration range of 8 μM to 1000 μM, to that of AA 10 μM to 2000 μM, with correlation coefficients of 0.9930 and 0.9945, respectively. The linear range is much wider than previously reported.     

Selective Simultaneous Determination of Paracetamol and Uric Acid Using a Glassy Carbon Electrode Modified with Multiwalled Carbon Nanotube/Chitosan Composite

A multiwalled carbon nanotube/chitosan modified glassy carbon electrode (MWCNTs‐CHT/GCE) has been used for simultaneous determination of paracetamol (PAR) and uric acid (UA). The measurements were carried out using differential pulse voltammetry (DPV), cyclic voltammetry (CV) and chronoamperometry (CA). DPV measurements showed a linear relationship between oxidation peak current and concentration of PAR and UA in phosphate buffer (pH 7) over the concentration range 2 µM to 250 µM, and 10 µM to 400 µM, respectively. The analytical performance of this sensor has been evaluated for detection of PAR and UA in human serum and human urine with satisfactory results.     

A Novel Strategy for Simultaneous Determination of Dopamine and Uric Acid Using a Carbon Paste Electrode Modified with CdTe Quantum Dots

A novel CdTe quantum dots‐modified carbon paste electrode (QDMCPE) was fabricated and used to study the electrooxidation of dopamine and uric acid and their mixtures by electrochemical methods. Using square wave voltammetry (SWV), a highly sensitive and simultaneous determination of dopamine and uric acid was explored at the modified electrode. SWV peak currents of dopamine and uric acid increased linearly with their concentrations in the ranges of 7.5×10^?8–6.0×10^?4 M, and 7.5×10^?6–1.4×10^?3 M, respectively. Finally this new sensor was used for determination of dopamine and uric acid in some real samples.     

Silver Doped Poly(L‐valine) Modified Glassy Carbon Electrode for the Simultaneous Determination of Uric Acid,Ascorbic Acid and Dopamine

In this paper, a silver doped poly(L ‐valine) (Ag‐PLV) modified glassy carbon electrode (GCE) was fabricated through electrochemical immobilization and was used to electrochemically detect uric acid (UA), dopamine (DA) and ascorbic acid (AA) by linear sweep voltammetry. In pH 4.0 PBS, at a scan rate of 100 mV/s, the modified electrode gave three separated oxidation peaks at 591 mV, 399 mV and 161 mV for UA, DA and AA, respectively. The peak potential differences were 238 mV and 192 mV. The electrochemical behaviors of them at the modified electrode were explored in detail with cyclic voltammetry. Under the optimum conditions, the linear ranges were 3.0×10^?7 to 1.0×10^?5 M for UA, 5.0×10^?7 to 1.0×10^?5 M for DA and 1.0×10^?5 to 1.0×10^?3 M for AA, respectively. The method was successfully applied for simultaneous determination of UA, DA and AA in human urine samples.