Isocratic Separation of Dansylated Biogenic Amines on a C8‐Bonded Silica Column under the LC Elution of Methanol‐Based Mobile Phase

Under the elution of methanol‐based mobile phase, the isocratic resolution of 12 biogenic amines, including 1 aromatic, 2 heterocyclic and 9 aliphatic amines, as the dansylated derivatives has been accomplished in less than 25 minutes on a 15 cm C₈‐bonded column. The resolution can not be reproduced on other examined alkyl‐bonded phases (e.g., C₄ and C₁₈) under the same chromatographic conditions, or in the reversed‐phase mode. The retention, mainly as a result of hydrophobic interaction between analyte and stationary phase, can be adjusted by varying the percentage of methanol in the mobile phase. Also, incorporating acetic acid as additive to the mobile phase to protonate the analyte and silanol groups that are little shielding on the surface of silica gel reduces the dipole‐dipole interaction, and thus the retention scale, which in turn deteriorates the resolution. Furthermore, the elution reversal is plausible for some of analytes as a greater percent of acetic acid is used in the elution. Values of correlation coefficients (R²) range between 0.9995 and 0.9996, indicating good linearity.     

Gaschromatographische Untersuchung der Adsorptionseigenschaften von Silicalit und ZSM-5

High silica molecular sieves (silicalite, ZSM-5) were tested as adsorbents for gas chromatographic trace analysis. Therefore the retention behaviour of low-boiling organic compounds (hydrocarbons, halogenated hydrocarbons, amines, alcohols and ethers) on these materials was investigated. The specific retention volumes at different temperatures have been determined and elution orders and peak shapes were studied. The retention data allow a simple calculation of the breakthrough volumes (dynamic adsorption capacity) and the chromatographic characterisation of the adsorbents. Both nitrogen and oxygen containing compounds could not—or at least unreproducibely—be eluated up to 300°. The elution order and the peak shape of compounds with the same number of carbon atoms but different geometric and electronic structure (e.g.n-butenes;n-hexane, cyclohexane, benzene) can be explained by the action of exclusion effects and different diffusion barriers. On the basis of calculated breakthrough volumes we conclude that silicalite should be useful in the preconcentration of both saturated C₃–C₆ hydrocarbons and C₁–C₂ chlorinated hydrocarbons from gaseous streams.     

Survey and Trends in the Preparation of Chemically Bonded Silica Phases for Liquid Chromatographic Analysis

In order to increase chromatographic selectivity and to extend the analytical capability of reversed phase liquid chromatography (RP HPLC) many investigators have concentrated on the preparation of silica based column packings with chemically bonded phases (CBP). These phases have also been successfully used in sample preparation techniques, mainly in solid phase extraction (SPE). Although alkyl bonded phases (e.g., C₂, C₈, and C₁₈) are the most widely used packings in RP HPLC and SPE, various specific applications require CBPs with polar functional groups (e.g., -NH₂, -NO₂, -CN, and/or -OH). The solution of problems with separation of complicated chiral compounds was attempted by applying stationary phases with chiral selectors (e.g., cyclodextrins, Pirkle phases, crown ethers, etc.). On the other hand, packings with pseudo-membrane or liquid crystal properties have been utilized for the separation of various substances of natural origin. Porous silica is commonly used as a support in the preparation of CBPs. Its physico-chemical characteristics, such as: type and structure of siliceous matrix, porosity, type and concentration of silanol groups, as well as surface purity, strongly influence the density and structure of chemically bonded phases. Recognition of these properties is helpful in optimizing separation processes based on RP HPLC elution and/or extraction of substances with polar character.     

Benefits of Innovative and Fully Water-Compatible Stationary Phases of Thin-Film Microextraction (TFME) Blades

Octadecyl (C₁₈) groups are arguably the most popular ligands used for preparation of solid phase microextraction (SPME) devices. However, conventional C₁₈-bonded silica particles are not fully compatible with the nearly 100% aqueous composition of typical biological samples (e.g., plasma, saliva, or urine). This study presents the first evaluation of thin-film SPME devices coated with special water-compatible C₁₈-bonded particles. Device performance was assessed by extracting a mixture of 30 model compounds that exhibited various chemical structures and properties, such as hydrophobicity. Additionally, nine unique compositions of desorption solvents were tested. Thin-film SPME devices coated with C₁₈-bonded silica particles with polar end-capping groups (10 µm) were compared with conventional trimethylsilane end-capped C₁₈-bonded silica particles of various sizes (5, 10, and 45 µm) and characteristics. Polar end-capped particles provided the best extraction efficacy and were characterized by the strongest correlations between the efficacy of the extraction process and the hydrophobicity of the analytes. The results suggest that the original features of octadecyl ligands are best preserved in aqueous conditions by polar end-capped particles, unlike with conventional trimethylsilane end-capped particles that are currently used to prepare SPME devices. The benefits associated with this improved type of coating encourage further implementation of microextractraction as greener alternative to the traditional sample preparation methods.     

Solid-phase extraction of carotenoids

In this work, solid-phase extraction (SPE) trapping performance of lutein and β-carotene, which were used as the model molecules of carotenoids, was investigated. The absorption, elution, and enrichment of carotenoids on SPE cartridges with four different sorbents, i.e. C₃₀, C₁₈, diol, and silica, were compared respectively with the help of frontal analysis technique. The high retentions of both lutein and β-carotene were achieved on the C₁₈ and C₃₀ cartridges. The diol and silica cartridges only had good retention for lutein. The optimized SPE method for sample pretreatment for the carotenoids analysis was obtained after the investigation of trapping performance. The method was applied successfully to the analysis of biological sample, i.e. serum and human breast milk. The recovery, accuracy, and precision of SPE method comparing with those of traditional liquid–liquid extraction (LLE) method for the sample pretreatment for the analysis of carotenoids owned a number of advantages such as rapid, no chloroform used, and accurate versus LLE.     

Automated screening of reversed‐phase stationary phases for small‐molecule separations using liquid chromatography with mass spectrometry

There are various reversed‐phase stationary phases that offer significant differences in selectivity and retention. To investigate different reversed‐phase stationary phases (aqueous stable C₁₈, biphenyl, pentafluorophenyl propyl, and polar‐embedded alkyl) in an automated fashion, commercial software and associated hardware for mobile phase and column selection were used in conjunction with liquid chromatography and a triple quadrupole mass spectrometer detector. A model analyte mixture was prepared using a combination of standards from varying classes of analytes (including drugs, drugs of abuse, amino acids, nicotine, and nicotine‐like compounds). Chromatographic results revealed diverse variations in selectivity and peak shape. Differences in the elution order of analytes on the polar‐embedded alkyl phase for several analytes showed distinct selectivity differences compared to the aqueous C₁₈ phase. The electron‐rich pentafluorophenyl propyl phase showed unique selectivity toward protonated amines. The biphenyl phase provided further changes in selectivity relative to C₁₈ with a methanolic phase, but it behaved very similarly to a C₁₈ when an acetonitrile‐based mobile phase was evaluated. This study shows the value of rapid column screening as an alternative to excessive mobile phase variation to obtain suitable chromatographic settings for analyte separation.     

Relationships between Retention Factors and Analyte Hydrophobicity on Cyanopropyl and n‐Octadecyl Bonded Silicas,Cross‐Linked Polymers and Porous Graphitic Carbon Stationary Phases. Consequences for the Trace Analysis of Highly Polar Organic Compounds

LC retention data have been measured using various stationary phases with an emphasis on highly polar to moderately polar neutral organic compounds having octanol‐water partition coefficients (K_ow) in log units between 0 and 3. The relationships between the retention factor measured in water and the octanol‐water partition coefficient are linear but with different slopes for octadecyl (C₁₈) silicas, and two polystyrene divinylbenzene (PS‐DVB) phases with low and high surface areas. These relationships confirm that highly cross‐linked polymers can provide more than 1000‐times higher retention values than C₁₈ silicas for moderately polar analytes but close values for highly polar ones. They also explain why C₁₈ silicas and polymers are equivalent for the separation of very polar analytes. In contrast, due to a different retention mechanism, no relation exists between the retention shown by porous graphitic carbons (PGC) and analyte hydrophobicity, but highly polar analytes are in general much more strongly retained than by any other sorbent. The potential of PGC for both the extraction and the separation of analytes is shown. Due to the difference in separation mechanism, PGC is the analytical phase that should be used for confirmation of the identity of analytes instead of a cyanopropylsilica column as recommended in some environmental procedures. Applications are presented for the trace‐determination of triazines and polar degradation products in ground and surface water with detection limits below the 0.1 μg/L level.     

Evaluation of an amide‐based stationary phase for supercritical fluid chromatography

A relatively new stationary phase containing a polar group embedded in a hydrophobic backbone (i.e., ACE ® C18‐amide) was evaluated for use in supercritical fluid chromatography. The amide‐based column was compared with columns packed with bare silica, C₁₈ silica, and a terminal‐amide silica phase. The system was held at supercritical pressure and temperature with a mobile phase composition of CO₂ and methanol as cosolvent. The linear solvation energy relationship model was used to evaluate the behavior of these stationary phases, relating the retention factor of selected probes to specific chromatographic interactions. A five‐component test mixture, consisting of a group of drug‐like molecules was separated isocratically. The results show that the C₁₈‐amide stationary phase provided a combination of interactions contributing to the retention of the probe compounds. The hydrophobic interactions are favorable; however, the electron donating ability of the embedded amide group shows a large positive interaction. Under the chromatographic conditions used, the C₁₈‐amide column was able to provide baseline resolution of all the drug‐like probe compounds in a text mixture, while the other columns tested did not.     

Separation of Dietary Folates by Gradient Reversed-Phase HPLC: Comparison of Alternative and Conventional Silica-Based Stationary Phases

A study of ten silica-based stationary phases and gradient elution conditions to separate dietary folates by reversed-phase HPLC was performed. Alkyl-bonded stationary phases (both conventional and alternative) were found to be the most promising for the separation of different folate monoglutamates in terms of selectivity and peak shape. These phases were better than phenyl-bonded phases which lacked selectivity when separating 10-formyl-folic acid and 5-formyl-tetrahydrofolate. Polar-bonded (cyano) stationary phase showed similar retention characteristics as the conventional alkyl-bonded phases, but ranked below those in terms of peak shape. Overall, alternative stationary phases exhibited slightly higher retention of late-eluted folates and greater retention variability for early-eluting tetrahydrofolate and 5-methyl-tetrahydrofolate. Best selectivity was achieved on alternative polar endcapped Aquasil C₁₈ followed by conventional Synergy MAX C₁₂ and Genesis C₁₈ stationary phases.     

Influence of intermolecular interaction with the eluent on the retention of phenol and aniline on polar and non-polar surfaces

Summary The retention order of aniline and phenol on hydroxylated silica gel surface is reversed with the increase of the concentration of a polar component in the eluent. At minor (about 1%) concentrations of isopropanol in hexane aniline emerges first followed by phenol, the elution order being reversed with the increase of isopropanol concentration above 2%. The same behaviour is observed for silica gel with chemically bonded C₁₆ n-alkyl groups and for porous styrene-divinylbenzene copolymer. In all these cases the retention depends to a great extent on substance-eluent intermolecular interactions. At high isopropanol concentration in hexane the rise of column temperature changes the retention order of aniline and phenol on silica gel with hydroxylated surface since the association of these molecules with isopropanol as well as the isopropanol adsorption weaken as the temperature increases.     

Investigation of Symphytum cordatum alkaloids by liquid-liquid partitioning, thin-layer chromatography and liquid chromatography-ion-trap mass spectrometry

From the alkalised crude extract of Symphytum cordatum (L.) W.K. roots, pyrrolizidine alkaloids (PAs) were extracted as free tertiary bases and polar N-oxides in a merely one-step liquid-liquid partitioning (LLP) in separation funnel and subsequently pre-fractionated by preparative multiple-development (MD) thin-layer chromatography (TLC) on silica gel plates. In this way three alkaloid fractions of different polarities and retention on silica gel plates were obtained as: the most polar N-oxides of the highest retention, the tertiary bases of medium retention, and diesterified N-oxides of the lowest retention. The former fraction was reduced into free bases by sodium hydrosulfite and purified by LLP on Extrelut-NT3 cartridge. It was further analysed together with the two other fractions by high-performance liquid chromatography (HPLC)-ion-trap mass spectrometry with atmospheric pressure chemical ionization (APCI) interface on XTerra C₁₈ column using a gradient elution. Based on MSⁿ spectra, 18 various alkaloids have been tentatively determined for the first time in this plant as the following types of structure: echimidine-N-oxide (three diasteroisomers), 7-sarracinyl-9-viridiflorylretronecine (two diasteroisomers), echimidine (two diasteroisomers), lycopsamine (two diasteroisomers), dihydroechinatine-N-oxide, dihydroheliospathuline-N-oxide, lycopsamine-N-oxide (three diasteroisomers), 7-acetyllycopsamine-N-oxide, symphytine-N-oxide (two diasteroisomers) and 2″,3″-epoxyechiumine-N-oxide.     

A Study of the Relative Importance of Lipophilic, π–π and Dipole–Dipole Interactions on Cyanopropyl, Phenyl and Alkyl LC Phases Bonded onto the Same Base Silica

Cyano (CN), butyl (C₄), phenyl and octadecyl (C₁₈) phases prepared from the same base silica gel were chromatographically characterized in order to assess the relative importance of lipophilic, π–π and dipole–dipole interactions in governing retention on these differing phases. Dipole interactions of analytes (possessing dipole moments and low lipophilicity) with CN phases were primarily responsible for the elution order. However, as the analytes’ lipophilicity increased, the lipophilic interaction predominated over the dipole interaction. In comparison, retention on the phenyl phase appeared to be complex, being controlled by a mixture of lipophilic, π–π and dipole–dipole interactions. Retention on the C₄ and C₁₈ phases was dictated by the analyte’s lipophilicity and its accessibility into the phase.     

Application of an ampholine‐functionalized hybrid organic–inorganic silica material for the SPE of aromatic amines

An SPE cartridge based on an ampholine‐functionalized hybrid organic–inorganic silica sorbent has been adopted for the analysis of aromatic amines including 4‐aminobiphenyl, benzidine, 2‐naphthylamine, p‐chloroaniline, 2,4,5‐trimethylaniline, and 3,3′‐dichlorobenzidine. Crucial variables governing the extraction efficiency of the material such as the pH of sample, sample loading volume, solvent used for elution, and elution volume have been thoroughly optimized. The adsorption capacities for the six aromatic amines ranged from 0.17 to 1.82 μg/mg. The recoveries of aromatic amines spiked in textile samples ranged from 78.9 to 103.0%, with RSDs of 1.1–11.9% (n = 3). Moreover, the extraction efficiency of the ampholine‐functionalized hybrid organic–inorganic silica sorbent was at least comparable with that of Oasis WCX.     

Chromatographic Properties of Monolithic Silica Capillary Columns for Polar and Nonpolar Compounds in Reversed-Phase HPLC

Retention properties of monolithic silica C₁₈ columns were examined for polar and nonpolar compounds. Monolithic silica columns were prepared from two kinds of starting materials, tetramethoxysilane (abbreviated as TMOS) or a mixture of TMOS and methyltrimethoxysilane (abbreviated as Hybrid), and modified with dimethyloctadecylchlorosilane (C₁₈). Retention factors of various compounds on Hybrid-C₁₈ are about twice as much as that on TMOS-C₁₈. The two types of columns showed very similar retention selectivity with few exceptions. TMOS-C₁₈ showed slight preference toward planar polynuclear aromatic hydrocarbons (PAHs) compared to bulky aromatic hydrocarbons, while Hybrid-C₁₈ showed opposite tendency. Some TMOS-C₁₈ columns showed peak tailing for PAHs, and also for basic compounds in an acidic mobile phase, while Hybrid-C₁₈ and majority of TMOS-C₁₈ columns resulted in good peak shape for these compounds.     

Factors affecting the reversed-phase liquid chromatographic separation of polycyclic aromatic hydrocarbon isomers

Reversed-phase liquid chromatography (LC) on C₁₈ stationary phases provides excellent selectivity for the separation of polycyclic aromatic hydrocarbons (PAH). Recent studies have shown that several factors affect selectivity for the LC separation of PAH including phase type (monomeric or polymeric), pore diameter and surface area of the silica substrate, and surface density of the C₁₈ ligands. In this paper the separation of eleven PAH isomers of molecular weight 278 is used to further illustrate the effect of stationary phase characteristics and shape of the solute (length-to-breadth ratio, L/B) on retention and selectivity. Only polymeric C₁₈ phases with a high C₁₈ surface coverage provided separation of all eleven isomers and the elution order of these isomers generally followed increasing L/B values. The effect of solute nonplanarity on reversed-phase LC retention was investigated on both monomeric and polymeric phases using a series of planar and nonplanar PAH pairs. For each solute pair, the nonplanar solute eluted earlier than the planar solute, the largest selectivity factors being observed on the C₁₈ phase with the highest percent carbon load. Based on these studies, a model is proposed to describe the retention of PAH on polymeric C₁₈ phases.     

SPE – Microwave‐assisted extraction coupled system for the extraction of pesticides from water samples

SPE is a commonly applied technique for preconcentration of pesticides from water samples. Microwave‐assisted extraction (MAE) technique is the extraction applied for preconcentration of different compounds from solid samples. SPE coupled with MAE is capable of preconcentrating these compounds from water samples too. This investigation was aimed at improving the efficiency of atrazine, alachlor, and α‐cypermethrin pesticide extraction from the spiked water samples applying SPE followed by MAE. In this way, MAE served for elution of pesticides from C₁₈‐extraction disks with solvent heated by microwave energy. Various elution conditions were tested for their effects on the extraction efficiency of the SPE–MAE combined technique. Several parameters, such as elution solvent volume (mL), elution temperature (°C), and duration of elution (min), affect the extraction efficiency of the SPE–MAE coupled system and need to be optimized for the selected pesticides. In order to develop a mathematical model, 15 experiments were performed in the central composite design. The equation was then used to predict recoveries of the pesticides under specific experimental conditions. Optimization of microwave extraction was accomplished using the genetic algorithm approach. Best results were achieved using 20 mL of ethanol at 60°C. Optimal hold time was 5 min and 24 s. The SPE–MAE combination was also compared with the conventional SPE extraction technique with elution of a nonpolar or a moderately polar compound with nonpolar solvents.     

A Study of the Retention Behaviour of Various Organometallic Complexes in HPLC Phase Systems

Abstract

The retention behaviour of various organometallic complexes in HPLC has been investigated. Three polar adsorbents (silica, a CN-bonded and a diol-bonded stationary phase) and a nonpolar adsorbent (C₁₈-bonded stationary phase) were used in this study for normal phase LC and reversed-phase LC respectively. The retention is influenced by the type of metal atom and the type of ligand in both types of LC. The study includes complexes of iron, ruthenium, cobalt, manganese, molybdenum and nickel with di-aza-butadiene and tetra-azadiene ligands. It was found that some ruthenium complexes are not eluted from bare and chemically modified silica.     

Relevance of 1,2,5,6,9,10-hexabromocyclododecane diastereomer structure on partitioning properties,column-retention and clean-up procedures

To optimize clean-up procedures for the analysis of α-, β-, and γ-hexabromocyclododecanes (HBCD) in environmental and biological extracts, their retention behavior on silica gel and florisil was investigated using diverse mobile-phase solvents and accounting for matrix effects. The β-diastereomer, relative to the α- and γ-diastereomers, is substantially retained on both florisil and silica gel regardless of the solvent used. The β-diastereomer is therefore prone to undergo selective loss during clean-up. This sequence is counterintuitive to sequences based on reverse-phase chromatography with a C₁₈-column, in which the α- (and not the β-) isomer is eluted first when using a polar solvent. There has been some discrepancy regarding the structures of these diastereomers in the literature, with structures based on X-ray crystallography only becoming recently available. Based on these X-ray crystal structures, physical–chemical properties (the octanol–water partitioning constant, the Henry's law constant, subcooled liquid vapour pressures and subcooled liquid water solubilities) of the HBCD diastereomers were estimated using the quantum-chemistry based software COSMOtherm, and were found to differ from previously calculated values using different structures (e.g. log K_aw for α-, β-, and γ-HBCD are here estimated to be −8.3, −9.3 and −8.2 respectively). Hypothesis relating differences in structure to physical–chemical properties and retention sequences are presented. The extra retention of the β-diastereomer on silica gel and florisil is likely because it can form both greater specific (i.e. polar) and non-specific (i.e. non-polar) interactions with surfaces than the other diastereomers. Non-specific interactions can also account for the counter-intuitive elution orders with C₁₈-reverse-phase chromatography. These results indicate that care should be taken when isolating HBCDs and other molecular diastereomers from environmental and biological samples, and that reported concentrations of β-HBCD in the literature may be negatively biased.     

Determination of anionic surfactants in lubrication fluids

A simple method is described for the isolation and determination of anionic surfactants in oils and emulsions used as lubricants in metal working processes. The oils were separated on silica gel solid phase extraction columsn by successive elution of solvents with increasing polarity as hexane, diisopropyl ether, acetic acid ethyl ester, acetone and methanol/NH₃ (8:1). The most polar methanol phase, which contains the surfactants, was titrated with Hyamine and the end point was determined potentiometrically using an ion sensitive electrode. The retention behaviour of sulfonates and sulfates on the sorbent has not been affected by other lubricants.     

Study of RP HPLC Retention Behaviours in Analysis of Carotenoids

For determination of selected carotenoids, various types of columns for high-performance liquid chromatography (HPLC) with different properties have been used. The characteristics of the laboratory-used packing material containing monomeric alkyl-bonded phases (C₁₈, C₃₀) and phenyl as well as phenyl-hexyl stationary phases were studied. The retention data of the examined compounds were used to determine the hydrophobicity and silanol activity of stationary phases applied in the study. The presence of the polar and carboxyl groups in the structure of the bonded ligand strongly influences the polarity of the stationary phase. Columns were compared according to methylene selectivity using a series of benzene homologues. The measurements were done using a methanol–water mobile phase. Knowledge of the properties of the applied stationary phase provided the possibility to predict the RP HPLC retention behaviours in analysis of carotenoids including lutein, lycopene and β-carotene. The composition of the mobile phase, the addition of triethylamine and the type of stationary phase had been taken into account in designing the method of carotenoid identification. Also a monolithic column characterised by low hydrodynamic resistance, high porosity and high permeability was applied. The presented results show that the coverage density of the bonded ligands on silica gel packings and length of the linkage strongly influence the carotenoid retention behaviours. In our study, the highest retention parameters for lutein, lycopene and β-carotene were observed for C₃₀ and C₁₈ stationary phase. This effect corresponds with pore size of column packing greater than 100 Å and carbon content higher than 11 %.