Recovery and pre-concentration of gold onto poly((N-(Hydroxymethyl)methacrylamide)–1-allyl-2-thiourea) hydrogels synthesized by gamma radiation

Poly((N-(Hydroxymethyl)methacrylamide)–1-allyl-2-thiourea) hydrogels, Poly(NHMMA–ATU), were synthesized by gamma radiation using ⁶⁰Co γ source at different irradiation doses and different ATU content in the irradiated monomer mixture. The swellability of the synthesized hydrogels was changed by irradiation doses and by the content of ATU in the irradiated mixture. These hydrogels were used for the specific gold recovery and pre-concentration from single gold ion solutions and from different natural samples. It has been observed that gold adsorption capacity onto the hydrogels was high at low pHs and reached maximum value at pH = 0.5. Adsorption capacity of the hydrogels for gold at pH = 0.5 was found to be about 698 mg g^− 1 dry hydrogels. Adsorption equilibrium time of gold ions onto the hydrogels was found to be very short and also these hydrogels were showed extremely high selectivity to the gold ions in acidic media when the concentration of the other metal ions were extremely higher than gold. Because of the high specificity of these hydrogels to gold beside the other metal ions at low pHs, all matrix effects were easily eliminated adsorbing gold onto the hydrogels and desorbing into 3 M HCl solution containing 0.8 M thiourea. These hydrogels were found to be highly open pore size. This property of the hydrogels make them attractive due to high adsorption capacity of gold ions on/in the hydrogels penetrating inside and react to all functional groups in the interior surface of the hydrogels.     

Recovery and pre-concentration of gold onto poly((N-(Hydroxymethyl)methacrylamide)–1-allyl-2-thiourea) hydrogels synthesized by gamma radiation

Poly((N-(Hydroxymethyl)methacrylamide)–1-allyl-2-thiourea) hydrogels, Poly(NHMMA–ATU), were synthesized by gamma radiation using ⁶⁰Co γ source at different irradiation doses and different ATU content in the irradiated monomer mixture. The swellability of the synthesized hydrogels was changed by irradiation doses and by the content of ATU in the irradiated mixture. These hydrogels were used for the specific gold recovery and pre-concentration from single gold ion solutions and from different natural samples. It has been observed that gold adsorption capacity onto the hydrogels was high at low pHs and reached maximum value at pH = 0.5. Adsorption capacity of the hydrogels for gold at pH = 0.5 was found to be about 698 mg g^− 1 dry hydrogels. Adsorption equilibrium time of gold ions onto the hydrogels was found to be very short and also these hydrogels were showed extremely high selectivity to the gold ions in acidic media when the concentration of the other metal ions were extremely higher than gold. Because of the high specificity of these hydrogels to gold beside the other metal ions at low pHs, all matrix effects were easily eliminated adsorbing gold onto the hydrogels and desorbing into 3 M HCl solution containing 0.8 M thiourea. These hydrogels were found to be highly open pore size. This property of the hydrogels make them attractive due to high adsorption capacity of gold ions on/in the hydrogels penetrating inside and react to all functional groups in the interior surface of the hydrogels.     

Matrix elimination method for the determination of precious metals in ores using electrothermal atomic absorption spectrometry

Poly(N-(hydroxymethyl)methacrylamide)-1-allyl-2-thiourea) hydrogels, poly(NHMMA-ATU), were synthesized by gamma radiation using ⁶⁰Co γ source in the ternary mixture of NHMMA-ATU-H₂O. These hydrogels were used for the specific gold, silver, platinum and palladium recovery, pre-concentration and matrix elimination from the solutions containing trace amounts of precious metal ions. Elimination of inorganic matrices such as different transition and heavy metal ions, and anions was performed by adjusting the solution pH to 0.5 that was the selective adsorption pH of the precious metal ions. Desorption of the precious metal ions was performed by using 0.8 M thiourea in 3 M HCl as the most efficient desorbing agent with recovery values more than 95%. In the desorption medium, thiourea effect on the atomic signal was eliminated by selecting proper pyrolysis and atomization temperatures for all precious metal ions. Precision and the accuracy of the results were improved in the graphite furnace-atomic absorption spectrometer (GFAAS) measurements by applying the developed matrix elimination method performing the adsorption at pH 0.5. Pre-concentration factors of the studied precious metal ions were found to be at least 1000-fold. Detection limits of the precious metal ions were found to be less than 10 ng L⁻¹ of the all studied precious metal ions by using the proposed pre-concentration method. Determination of trace levels of the precious metals in the sea-water, anode slime, geological samples and photographic fixer solutions were performed using GFAAS clearly after applying the adsorption-desorption cycle onto the poly(NHMMA-UTU) hydrogels.     

Preparation, characterization, swelling and in vitro drug release behaviour of poly[N-acryloylglycine-chitosan] interpolymeric pH and thermally-responsive hydrogels

Novel biodegradable pH- and thermal-responsive interpenetrating polymer network (IPN) hydrogels were prepared for controlled drug delivery studies. The IPN hydrogels were obtained in mild aqueous acid media by irradiation of solutions of N-acryloylglycine (NAGly) mixed with chitosan, in the presence of glutaraldehyde as a crosslinking agent and using 2,2-dimethoxy-2-phenyl acetophenone as photoinitiator. These hydrogels were subjected to equilibrium swelling studies at different temperatures (25 °C, 37 °C and 45 °C) in buffer solutions of pH 2.1 and 7.4 (similar to that of gastric and intestinal fluids respectively). 5-Fluorouracil (5-FU) was entrapped in the hydrogels, and drug release studies carried out at 37 °C in buffer solutions at pH 2.1 and 7.4.     

Synthesis and characterization of PVP/AAc copolymer hydrogel and its applications in the removal of heavy metals from aqueous solution

Chelating poly(vinylpyrrolidone/acrylic acid) (PVP/AAc) copolymer hydrogels were prepared by radiation-induced copolymerization. The effects of preparation parameters such as PVP content in the hydrogel and irradiation dose on the swelling behavior of the hydrogel were studied. The pH dependent swelling was investigated. The thermal stability of the prepared hydrogel and the metal chelated ones was characterized by TGA. The removal of Fe(III), Cu(II), and Mn(II) from aqueous solution by the prepared PVP/AAc chelating hydrogel was examined by batch equilibration technique. The influence of treatment time, pH, and the initial feed concentration on the amount of the metal ions removed was studied. The results show that the removal of the metal ion followed the following order: Fe(III) > Cu(II) > Mn(II). The amounts of the removed metal ions increased with treatment time and pH of the medium. To re-use the hydrogel, the metal ions were stripped by using 2 N HCl.     

Preparation of molecularly imprinted polymers with thiourea group for phosphate

Molecularly imprinted polymers selective for phosphate were prepared with the two types of functional monomers, 1-allyl-2-thiourea and N-methyl-N′-(4-vinylphenyl)-thiourea, and the binding abilities of the polymers were evaluated. Phenylphosphonic acid or diphenyl phosphate were used as the template molecules and the imprinted polymers prepared with 1-allyl-2-thiourea as functional monomer showed high binding ability to phosphate in aqueous media and nearly 90% of phosphate could be recovered. Also, the imprinted polymer prepared with N-methyl-N′-(4-vinylphenyl)-thiourea as functional monomer had a high binding ability and specific interaction with phosphate in acetonitrile solution and over 90% of phosphate-derivatives could be recovered selectively.     

Thermo- and pH-sensitive comb-type grafted poly(N,N-diethylacrylamide-co-acrylic acid) hydrogels with rapid response behaviors

Poly(N,N-diethylacrylamide) with a terminal hydroxyl end group (PDEA-OH) was synthesized by radical telomerization of N,N-diethylacrylamide (DEA) monomer using 2-hydroxyethanethiol as a chain transfer agent. Macromonomer of thermo-sensitive PDEA was synthesized by condensation reaction of PDEA-OH with acryloyl chloride. The macromonomer was characterized by FTIR and ¹H NMR, and the molecular weight was determined by GPC. Thermo- and pH-sensitive comb-type grafted poly(N,N-diethylacrylamide-co-acrylic acid) (PDEA-co-AA) hydrogels (GHs) were successfully prepared by grafting PDEA chains with freely mobile ends onto the backbone of a cross-linked (PDEA-co-AA) network. The results showed that the deswelling behavior of the hydrogels was dependent on the test temperature. At 45 °C (beneath the VPTT of the hydrogels), both the normal-type hydrogels (NHs) and comb-type grafted P(DEA-co-AA) hydrogels had lower deswelling rates. While at 60 °C (far beyond the VPTT of the hydrogels), the deswelling rates of the GHs were faster than that of the NHs. Furthermore, pulsatile stimuli-responsive studies indicated that the GHs had excellent thermo-reversibility and were superior to the NHs in the magnitude of their swelling ratios to temperature changes. However, the reversibility to pH changes was poor for both the NHs and the GHs.     

Adsorption of Uranyl Ions into Poly(Acrylamide‐co‐Acrylic Acid) Hydrogels Prepared by Gamma Irradiation

Acrylamide (AAm)/Acrylic Acid (AAc) copolymers have been prepared by gamma irradiation of binary mixtures at three different compositions where the acrylamide/acrylic acid mole ratios varied around 15, 20, and 30%. Threshold dose for 100% conversion of monomers into hydrogels was found to be 8.0 kGy. Poly(Acrylamide‐co‐Acrylic Acid) (poly(AAm‐co‐AAc)) hydrogels have been considered for the removal of uranyl ions from aqueous solutions. Swelling behavior of these hydrogels was determined in distilled water at different pH values and in aqueous solutions of uranyl ions. The results of swelling tests at pH 8.0 indicated that poly(AAm‐co‐AAc) hydrogel, containing 15% acrylamide showed maximum % swelling. Diffusion of water and aqueous solutions of uranyl ion into hydrogels was found to be non‐Fickian in character and their diffusion coefficients were calculated. The effect of pH, composition of hydrogel, and concentration of uranyl ions on the adsorption process were studied at room temperature. It was found that one gram of dry poly(AAm‐co‐AAc) hydrogel adsorbed 70–320 mg and 70–400 mg uranyl ions from aqueous solutions of uranyl nitrate and uranyl acetate in the initial concentration range of 50–1500 mg UO₂ ²⁺L^?, depending on the amount of AAc in the hydrogels, respectively. Adsorption isotherms were constructed for poly(AAm‐co‐AAc)–uranyl ion system indicating an S type of adsorption in the Giles classification system. It is concluded that crosslinked poly(AAm‐co‐AAc) hydrogels can be successfully used for the removal of uranyl ions from their aqueous solutions.     

Facile preparation of glutathione-stabilized gold nanoclusters for selective determination of chromium (III) and chromium (VI) in environmental water samples

A novel method for selective determination of Cr(III) and Cr(VI) in environmental water samples was developed based on target-induced fluorescence quenching of glutathione-stabilized gold nanoclusters (GSH-Au NCs). Fluorescent GSH-Au NCs were synthesized by a one-step approach employing GSH as reducing/protecting reagent. It was found that Cr(III) and Cr(VI) showed pH-dependent fluorescence quenching capabilities for GSH-Au NCs, and thus selective determination of Cr(III) and Cr(VI) could be achieved at different pHs. Addition of EDTA was able to effectively eliminate the interferences from other metal ions, leading to a good selectivity for this method. Under optimized conditions, Cr(III) showed a linear range of 25–3800 μg L⁻¹ and a limit of detection (LOD) of 2.5 μg L⁻¹. The Cr(VI) ion demonstrated a linear range of 5–500 μg L⁻¹ and LOD of 0.5 μg L⁻¹. The run-to-run relative standard deviations (n = 5) for Cr(III) and Cr(VI) were 3.9% and 2.8%, respectively. The recoveries of Cr(III) and Cr(VI) in environmental water samples were also satisfactory (76.3–116%). This method, with its simplicity, low cost, high selectivity and sensitivity, could be used as a promising tool for chromium analysis in environmental water samples.     

Coprecipitation with yttrium phosphate as a separation technique for iron(III), lead, and bismuth from cobalt, nickel, and copper matrices

The coprecipitation behavior of 44 elements (47 ions because of chromium(III,VI), arsenic(III,V), and antimony(III,V)) with yttrium phosphate was investigated at various pHs. Yttrium phosphate could quantitatively coprecipitate iron(III), lead, bismuth, and indium over a wide pH range; however, 18 ions, including alkali metals and oxo anions, such as vanadium(V), chromium(VI), molybdenum(VI), tungsten(VI), germanium(IV), arsenic(III,V), selenium(IV), and tellurium(VI), were scarcely collected. In addition, 19 ions, including cobalt, nickel, and copper(II), were hardly coprecipitated at pHs below about 3. Based on these results, the separation of iron(III), lead, and bismuth from cobalt, nickel, and copper(II) matrices was investigated. Iron(III), lead, and bismuth ranging from 0.5 to 25 μg could be separated effectively from a solution containing 0.5 g of cobalt, nickel, or copper at pH 3.0. The separated iron(III), lead, and bismuth could be determined by inductively coupled plasma atomic emission spectrometry using internal standardization. The detection limits (3σ, n = 7) of iron(III), lead, and bismuth were 0.008, 0.137, and 0.073 μg, respectively. The proposed method was applied to the analyses of metals and chlorides of cobalt, nickel, and copper.     

Synergistic liquid-liquid extractive spectrophotometric determination of gold(III) using 1-(2′,4′-dinitro aminophenyl)-4,4,6-trimethyl-1,4-dihydropyrimidine-2-thiol

Synergistic liquid-liquid extractive spectrophotometric determination of gold(III) using 1-(2′,4′-dinitro aminophenyl)-4,4,6-trimethyl-1,4-dihydro pyrimidine-2-thiol [2′,4′-dinitro APTPT] has been described. Equal volumes (5 cm³) of the 2′,4′-dinitro APTPT (0.02 mol L⁻¹) in the presence of pyridine (0.5 mol L⁻¹) form an orange-red coloured ternary complex with gold(III) of molar ratio 1:1:1 at pH 1.8-2.4 with 5 min of shaking. The absorbance of coloured organic layer in 1,2-dichloroethane is measured spectrophotometrically at 445 nm against reagent blank. A pronounced synergism has been observed by the binary mixture of 2′,4′-dinitro APTPT and pyridine, which shows that the enhancement in the absorbance is observed in the presence of pyridine by the adduct formation in the organic phase. Beer's law was obeyed in the concentration range 2.5-20.0 μg mL⁻¹, with molar absorptivity and Sandell's sensitivity values of 8.7 × 10³ dm³ mol⁻¹ cm⁻¹ and 0.023 μg cm⁻² respectively. A repetition of the method was checked by finding relative standard deviation (R.S.D.) (n = 10) which was 0.17%. The composition of the gold(III)-2′,4′-dinitro APTPT-pyridine adduct was established by slope analysis, molar ratio and Job's method. The ternary complex was stable for more than 48 h. The influence of various factors such as pH, 2′,4′-dinitro APTPT concentration, solvent and pyridine on the degree of complexation has been established. A number of foreign ions tested for their interferences and use of suitable masking agents wherever necessary are tabulated, which show that selectivity of the method has been enhanced. The method is successfully employed for the determination of gold(III) in binary, synthetic mixtures and ayurvedic samples. The reliability of the method is assured by inter-comparison of experimental values, using an atomic absorption spectrometer.     

Development of silver/gold nanocages onto indium tin oxide glass as a reagentless plasmonic mercury sensor

We demonstrate the utilization of silver/gold nanocages (Ag/Au NCs) deposited onto transparent indium tin oxide (ITO) film glass as the basis of a reagentless, simple and inexpensive mercury probe. The localized surface plasmon resonance (LSPR) peak wavelength was located at ∼800 nm. By utilizing the redox reaction between Hg²⁺ ions and Ag atoms that existed in Ag/Au NCs, the LSPR peak of Ag/Au NCs was blue-shifted. Thus, we develop an optical sensing probe for the detection of Hg²⁺ ions. The LSPR peak changes were lineally proportional to the concentration of Hg²⁺ ions over the range from 10 ppb to 0.5 ppm. The detection limit was ∼5 ppb. This plasmonic probe shows good selectivity and high sensitivity. The proposed optical probe is successfully applied to the sensing of Hg²⁺ in real samples.     

Sucrose diacrylate: A unique chemically and biologically degradable crosslinker for polymeric hydrogels

A series of degradable hydrogels based on different vinyl monomers such as acrylamide, sucrose-1′-acrylate, and acrylic acid were synthesized using sucrose-6,1′-diacrylate (SDA) as a crosslinking agent. SDA was prepared by enzymatic transesterification of vinyl acrylate with sucrose in pyridine. Base catalyzed hydrolysis of SDA in aqueous solution was studied as a function of pH. As expected, hydrolysis of SDA was faster at higher pHs such that poly(acrylamide), poly(sucrose 1′-acrylate), and poly(acrylic acid) hydrogels underwent substantial degradation at and above pH 7, 9, and 13, respectively. The degradation was characterized by changes in the swelling ratios of the hydrogels indicating breakage of the crosslinking agent. Degradation of the hydrogels at their chemically stable pHs was studied in presence of enzymes. Enzymes, including pepsin and a fungal Lipase, were able to degrade the poly(acrylamide) hydrogel at pH 4 and 5, respectively. Poly(acrylic acid) hydrogel was degraded in presence of a fungal protease at pH 7.8. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2221–2229, 1997     

pH-Sensitivity and pH-dependent structural change in polymeric nanoparticles of poly(vinyl sulfadimethoxine)-deoxycholic acid conjugate

pH-Sensitive nanoparticles of poly(vinyl sulfadimethoxine) (PSDM)-deoxycholic acid (DOCA) conjugates were prepared by dialysis at pH 9.0. The average size and the critical aggregation concentration (CAC) of the nanoparticles were 340 nm and 2.5 × 10⁻¹ g/l, respectively. The CAC decreased with decreasing pH as a result of the increase in the hydrophobic nature of the PSDM. Nanoparticle aggregation was observed at pHs ranging from 6.6 to 7.2. The photophysical characteristics of the nanoparticles were examined using a fluorescence probe technique. The microviscosity in the nanoparticle core was measured by 1,6-diphenyl-1,3,5-hexatriene (DPH). The microviscosity changed significantly with decreasing pH from 8.0 to 6.8, indicating a decrease in the rigidity of the inner cores. One interesting feature was that the microviscosity increased sharply at pHs below 6.8. This suggests that in this pH range most of the PSDM became deionized, which caused the reconstitution of new hydrophobic domains inside the nanoparticles.     

Development of a ratiometric time-resolved luminescence sensor for pH based on lanthanide complexes

Time-resolved luminescence bioassay technique using lanthanide complexes as luminescent probes/sensors has shown great utilities in clinical diagnostics and biotechnology discoveries. In this work, a novel terpyridine polyacid derivative that can form highly stable complexes with lanthanide ions in aqueous media, (4′-hydroxy-2,2′:6′,2′′-terpyridine-6,6′′-diyl) bis(methylenenitrilo) tetrakis(acetic acid) (HTTA), was designed and synthesized for developing time-resolved luminescence pH sensors based on its Eu³⁺ and Tb³⁺ complexes. The luminescence characterization results reveal that the luminescence intensity of HTTA–Eu³⁺ is strongly dependent on the pH values in weakly acidic to neutral media (pK_a = 5.8, pH 4.8–7.5), while that of HTTA–Tb³⁺ is pH-independent. This unique luminescence response allows the mixture of HTTA–Eu³⁺ and HTTA–Tb³⁺ (the HTTA–Eu³⁺/Tb³⁺ mixture) to be used as a ratiometric luminescence sensor for the time-resolved luminescence detection of pH with the intensity ratio of its Tb³⁺ emission at 540 nm to its Eu³⁺ emission at 610 nm, I_540 nm/I_610 nm, as a signal. Moreover, the UV absorption spectrum changes of the HTTA–Eu³⁺/Tb³⁺ mixture at different pHs (pH 4.0–7.0) also display a ratiometric response to the pH changes with the ratio of absorbance at 290 nm to that at 325 nm, A_290 nm/A_325 nm, as a signal. This feature enables the HTTA–Eu³⁺/Tb³⁺ mixture to have an additional function for the pH detection with the absorption spectrometry technique. For loading the complexes into the living cells, the acetoxymethyl ester of HTTA was synthesized and used for loading HTTA–Eu³⁺ and HTTA–Tb³⁺ into the cultured HeLa cells. The luminescence imaging results demonstrated the practical utility of the new sensor for the time-resolved luminescence cell imaging application.     

Synthesis of poly (acrylamide-co-aconitic acid) adsorbents by gamma-irradiation,characterization, adsorption studies and application for cationic dyes removal

In this study, acrylamide (AAm)/aconitic acid (ACA) copolymers were prepared with two different mol% of aconitic acid 4%, 17% and were irradiated with gamma irradiation at different irradiation doses (4 - 25kGy). The percent yield was assigned by gravimetrical method. The effect of irradiation dose, pH and involved amounts of monomers (AAm/ACA) in hydrogels on swelling properties were investigated. The conversion of monomers to hydrogels was 100% at 25kGy. Poly(acrylamide-co-aconitic acid) P(AAm/ACA) hydrogels have been used for the adsorption of some aqueous solutions of dyes such as Methylene Blue (MB) and Safranine-O (S). The hydrogels were swollen in distilled water at pH 3, 5, 7, 8 and in aqueous solutions of dyes. The initial swelling rates of hydrogels are increased by increasing of pH. The effects of concentration of the aqueous solutions of dye and hydrogel composition on the adsorption were investigated. The adsorption is increased and changed depending on the structure of dye and composition of hydrogel.     

Alumina modified by dimethyl sulfoxide as a new selective solid phase extractor for separation and preconcentration of inorganic mercury(II)

Dimethyl sulfoxide (DMSO) was simply immobilized to neutral alumina via quite strong hydrogen bonding between sulfoxide oxygen and surface alumina hydroxo groups. The produced alumina-modified dimethyl sulfoxide (AMDMSO) solid phase (SP)-extractor experienced high thermal and medium stability. Moreover, the small and compact size of DMSO moiety permit high surface coverage evaluated to be 2.1 ± 0.1 mmol g⁻¹ of alumina. Hg(II) uptake was 1.90 mmol g⁻¹(distribution coefficient log K_d = 5.658) at pH 1.0 or 2.0, 1.68 mmol g⁻¹ (log K_d = 4.067) at pH 3.0 or 4.0 while the metal ions Ca(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Cd(II) and Pb(II) showed low values 0.513-0.118 mmol g⁻¹ (log K_d < 3.0) in the pH range 4.0-7.0. A mechanism was suggested to explain the unique uptake of Hg(II) ions by binding as neutral and chloroanionic species predominate at pH values ≤ 3.0 of a medium rich in chloride ions. A direct and fast batch separation mode was achieved successfully to retain selectively Hg(II) in presence of other eight coexisting metal ions. Thus, Hg(II) was completely retained; Ca(II), Co(II), Ni(II) and Cd(II) were not retained, while Pb(II), Cu(II), Zn(II) and Fe(III) exhibited very low percentage retention evaluated to be 0.42, 0.49, 1.4 and 5.43%, respectively. The utility of the new modified alumina sorbent for concentrating of ultratrace amounts of Hg(II) was performed by percolating 2 l of doubly distilled water, drinking tap water, and Nile river water spiked with 10 ng/l over 100 mg of the sorbent packed in a minicolumn used as a thin layer enrichment bed prior to the determination by CV-AAS. The high recovery values obtained (98.5 ± 0.5, 98.5 ± 0.5 and 103.0 ± 1.0) based on excellent enrichment factor 1000, along with a good precision (R.S.D.% 0.51-0.97%, N = 3) demonstrate the accuracy and validity of the new modified alumina sorbent for preconcentrating ultratrace amounts of Hg(II) with no matrix interference.     

Fourier transform infrared spectroscopy study of the effect of pH on anion and cation adsorption onto poly(acrylo‐amidino diethylenediamine)

The role of hydrogen bonding in the chemistry of transition‐metal complexes remains a topic of intense scientific and technological interest. Poly(acrylo‐amidino diethylenediamine) was synthesized to study the effects of hydrogen bonding on complexes at different pHs. The polymer was synthesized through the coupling of diethylene triamine with polyacrylonitrile fiber in the presence of AlCl₃ · 6H₂O addition. The adsorption capacity of this polymer was 11.4 mequiv/g. The ions used for the adsorption test were CrO, PO, Cu²⁺, Ni²⁺, Fe²⁺, and Ag⁺. All experiments were confirmed with Fourier transform infrared. In the study of anion adsorption, at low pHs, only ionic bonds existed, whereas at high pHs, no bonds existed. However, in the middle pH region, both ionic bonds and hydrogen bonds formed between poly(acrylo‐amidino diethylenediamine) and the chromate ion or phosphate ion. When poly(acrylo‐amidino diethylenediamine) and metal ions (Cu²⁺, Ni²⁺, Fe²⁺, and Ag⁺) formed complexes, a hydrogen‐bonding effect was not observed with Fourier transform infrared. The quantity of metal ions adsorbed onto poly(acrylo‐amidino diethylenediamine) followed the order Ag⁺ > Cu²⁺ > Fe²⁺ > Ni²⁺. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2010–2018, 2004     

Determination of nickel in natural waters by FAAS after sorption on octadecyl silica membrane disks modified with a recently synthesized Schiff's base

A simple, highly sensitive, accurate and selective method for the determination of trace amounts of Ni²⁺ ions in water samples is proposed. The method is based on the separation and preconcentration of Ni²⁺ on an octadecyl-bonded silica (ODBS) membrane disk modified by a recently synthesized Schiff’s base N,N′-bis (3-methylsalicylidene) ortho phenylene diamine (MSOPD) at pH 7. The synthesis of this extractant ligand is also described. The retained nickel on the membrane was eluted with 2×5 ml 0.5 M HNO₃ and measured by flame atomic absorption spectrometry (FAAS) at 232.0 nm. The extraction efficiency and the influence of the type and least amount of eluent for the stripping of Ni²⁺ from the disks, pH, flow rates of sample solution and eluent, amount of MSOPD, effect of other ions, and breakthrough volume were evaluated. The maximum capacity of the membrane disks modified by 3 mg of MSOPD was found to be 146±4 μg Ni²⁺. The 3σ limit of detection of the method was 30 ng per 1000 ml and also an enrichment factor of 250 was obtained. The proposed method has been applied to the determination of nickel in several water samples with satisfactory results.     

Effects of low-level gamma irradiation on the characteristics of fermented pork sausage during storage

The effect of gamma irradiation (0.5, 1, 2, and 4 kGy) on the quality of vacuum-packaged dry fermented sausages during refrigerated storage was evaluated. At Day 0 of irradiation, the pH, redness (CIE a^?), yellowness (CIE b^?), 2-thiobarbituric acid-reactive substances (TBARS) and volatile basic nitrogen (VBN) values of samples irradiated at 2 and 4 kGy were higher (p<0.05), but the CIE L^? values (lightness) were lower than those of the non-irradiated control (p<0.05). At<1 kGy irradiation, however, the pH, CIE L^?, CIE a^? and CIE b^?-value of samples were not significantly influenced by irradiation. The CIE a^?, and CIE b^?-values of samples irradiated at 2 and 4 kGy decreased with the increase of storage time. The VBN, TBARS, and CIE L^?-values of samples irradiated at 4 kGy were not changed significantly during refrigerated storage for 90 days (p>0.05). The total plate counts (TPC) and lactic acid bacteria (LAB) in the samples irradiated at 4 kGy were significantly lower (p<0.01) than those with lower irradiation doses. At the end of storage, the TPC, coliform, and LAB in the samples were not increased after irradiation at 1, 0.5 and 1 kGy, respectively. TPC and LAB were not detected in samples irradiated at 4 kGy at Day 90. In addition, no coliform bacteria were found in samples irradiated at 1 kGy during refrigerated storage. Sensory evaluation indicated that the rancid flavor of samples irradiated at 4 kGy was significantly higher, but aroma and taste scores were lower than those of the control at Day 3 of storage. Irradiation of dry fermented sausages at 2 kGy was the best conditions to prolong the shelf-life and decrease the rancid flavor without significant quality deterioration.