Dielectric properties of poly(4-methylphenylisocyanate) and poly(4-methoxyphenylisocyanate) in solution

In the range 200 Hz-2 MHz, the dielectric behaviour of two polyarylisocyanates depends on the solvent. In certain solvents, such as toluene, there is only one high frequency absorption for poly(4-methylphenylisocyanate) and it is independent of molecular weight. Its character corresponds to chains having a low kinetic flexibility. In other solvents, this polymer, as well as poly(4-methoxyphenylisocyanate), shows two regions of dielectric absorption. The low frequency relaxation is molecular weight dependent: a polarization due to solvent polymer interactions occurs along the main chain. Despite its solvent-dependence, the total dipole moment of these polyarylisocyanates which behave like coils is much lower than that of polyalkylisocyanates, which are known to be rod-like.     

Co-nonsolvent systems for poly(ϵ-caprolactone) and poly(methyl methacrylate)

The cloud points for the co-nonsolvent systems (i) pyridine (PY) + formic acid (FA) towards poly(?-caprolactone) (PCL) or poly(methyl methacrylate) (PMMA) and (ii) pyridine + acetic acid (AA) towards PCL have been experimentally determined as a function of solvent composition at fixed polymer concentrations. Heats of mixing for the (FA + PY) system have also been measured. The single liquid approximation model correctly predicts for the (PY + FA) system the solvent composition at which the solvent power of the mixture is the poorest, provided it is recognized that the solvent system is comprised of pyridinium formate (PYFA) as one component and either PY or FA (depending on which is present in excess over 1:1 mole ratio) as the other. With the other co-nonsolvent system, the prediction is not as good. A possible reason for the discrepancy has been given.     

Thermal decomposition of some dihalotetramminecobalt(III) nitrates

The thermal decomposition of some dihalotetramminecobalt(III) nitrates [tetrammire =(NH₃)₄, (NH₃)₂(en), (NH₃)(dien), (en)₂, (pn)₂, (trien), etc.] with different degrees of chelation was studied by various thermoanalytical techniques. A partial oxidation—reduction was observed for these complexes above 200°C which was indicated by a rapid TG mass-loss and a large exothermic DTA peak. A relative order thermal stability is reported.     

Thermal decomposition of cesium hexanitratouranium(IV)

As cesium hexanitratouranium(IV), Cs₂U(NO₃)₆, has the same Cs:U stoichiometry as that of Cs₂UO₄, thermal decomposition of this nitrato complex in air and nitrogen was studied in detail as a possible alternate method of preparing pure Cs₂UO₄. The volatility of cesium nitrate, which is one of the intermediate products, changed this Cs:U ratio during thermal decomposition. Hence, only Cs₂U₂O₇ was obtained on heating the sample to 775 K or higher. A scheme for the thermal decomposition of Cs₂U(NO₃)₆ is given by combining the observed TG, XRD and IR data.     

Cationic degradation of poly(2-methyl-2-ethylthiirane)

Treatment of 2-methyl-2-ethylthiirane (MET) with the cationic initiator triethyloxonium tetrafluoroborate (TEFB) gives a fast and quantitative polymerization followed by a slow degradation of the polymer to a mixture of low molecular weight polymer, 2,5-dimethyl-2,5-diethyl-1,4-dithiane (cyclic dimer of MET), 3,6-dimethyl-3,6-diethyl-1,2,5-trithiepane and 2-methyl-2-butene. When high molecular weight poly-MET, obtained by anionic polymerization of MET with carbazyl potassium, is treated with a trace amount of TEFB, the polymer also degrades to the same low molecular weight compounds. In both cases both the cyclic degradation products were present as nearly equimolar mixtures of the cis- and trans-isomers. In the 1,4-dithianes mixture, a small amount of a third isomer was also detected. A mechanism for the degradation and the possible relation between polymer microstructure and the isomer distribution of the cyclic compounds are discussed.     

Permeability of poly(1-4-piperazinediylterephthaloyl) microcapsules towards sodium chloride

Water-loaded poly(1,4-piperazinediylterephthaloyl) (PPiP) microcapsules were prepared by an interfacial polycondensation technique using piperazine and terephthaloyl dichloride as water-soluble and water-insoluble monomers, respectively. The organic solvents used were mixtures of cyclohexane and chloroform and n-hexane and chloroform in various volume ratios. The microcapsules obtained were washed successively with n-hexane, acetone, and water and fractionated into several fractions of different sizes. A suspension of each fraction and a solution of sodium chloride were mixed and the change with time in electroconductivity of the mixture was measured to estimate the rate of salt entry into the microcapsules. The permeability coefficient for the salt was calculated from the rate of salt entry. It was found that the permeability increased as the capsule size increased and was higher for the capsules prepared with n-hexane—chloroform mixtures than for those prepared with cyclohexane—chloroform mixtures. These findings were explained in terms of the density and thickness of the capsule membrane.     

Phosphorescence of thermally oxidised poly(butadiene) and model enones: temperature dependence

The temperature dependence of phosphorescence of model enone compounds in poly (methyl methacrylate) matrix and glassy methylcyclohexane/isopentane solution and of enones formed from thermal oxidation of poly (butadiene) has been studied over the temperature range 77–220°K. The single discontinuity in the plot for the model enone-glassy solvent is due to the freezing of a (solvent perturbed) barrier to rotation in the enone, and an analogous transition is also observed in the model enone poly (methyl methacrylate) samples and in thermally oxidised poly (butadiene). In the polymer matrices, a second transition corresponding to the γ-transition in poly (methyl methacrylate) and the glass transition temperature T_g in poly (butadiene) are also revealed in the Arrhenius plots. The results demonstrate that care must be taken in ascribing such discontinuities solely to polymer properties since intrinsic properties of the luminescence probe itself may exhibit similar features.     

π-Arene complexes of the main group elements. II. Complexes of cadmium(II) and zinc(II)

π-Arene complexes of cadmium(II) and zinc(II) have been prepared from the first time. The 1:1 complexes Cd(AsF₆)₂. Arene(Arene=hexaethylor hexamethylbenzene, pentamethylbenzene, durene, $\text{p}$-xylene or benzene), Cd(SbF₆)₂. Arene(Arene = hexamethylbenzene, toluene or benzene) and Zn(SbF₆)₂. Arene(Arene = hexamethylbenzene or pentamethylbenzene) are synthesized from the strong acid salt and arene in liquid sulfur dioxide. ¹H and ¹³C NMR spectra are consistent with localized bonding of the arene to the metal cation. Exchange-averaged vn]¹³C chemical shifts for the systems Cd(AsF₆)₂-arene-SO₂ confirm the 1:1 stoichiometry in solution and suggest that the stabilities of the complexes are in the approximate range 0.48 – 2.1 M^?1 for the series benzene-hexamethylbenzene. For the system Cd(AsF₆)₂-C₆Me₆-SO₂, a detailed ¹¹³Cd NMR study is consistent with the solution stoichiometry and stability determined from ¹³C NMR. In general, complexation to an arene produces deshielding of the ¹¹³Cd resonance of Cd(AsF₆)₂.     

Thermal decomposition kinetics of bisthiourea cadmuim(II) tetrathiocyanato diammine chromate(III)

Cadmium thiourea reinickate undergoes two-stage thermal decomposition on heating. The DTG peak temperatures are 291 and 469°C and the corresponding DTA temperatures are 255 and 490°C. The kinetic parameters for the first stage decomposition are E* ≈ 120kJ mole^?1; Z ≈ 1.2 × 10⁸ cm³ mole^?1 sec^?1 and ΔS* ≈ ?95 J mole^?1 K^?1. For the second stage, E* ≈ 133 kJ mole^?1; Z ≈ 6.1 × 10⁵ cm^?1 mole^?1 sec^?1 and ΔS* ≈ ?142 J mole^?1 K^?1.     

Mechanistic studies on the photo-oxidation of commercial poly(butadiene)

Products from both the thermal and photo-oxidation of poly-butadiene have been studied using various analytical techniques such as infra-red and ultra-violet spectroscopy, gas-liquid chromatography and phosphorescence emission and phosphorescence excitation spectroscopy. Analyses have allowed a plausible mechanism to be formulated for the photo-oxidation of this polymer, consistent with all the observed physical and chemical changes. Both photo- and thermal oxidative polymer degradation initially result in the formation of α, β-unsaturated carbonyls which, under photo-degrading conditions, are subsequently photolysed to yield the observed final products.     

Thermal decomposition of mixed ligand complexes of cobalt(II), nickel(II), zinc(II) and cadmium(II) containing 1,3-diaminopropan-2-ol and oxalate

Non-isothermal kinetics of the thermal decomposition of mixed ligand complexes of cobalt(II), nickel(II), zinc(II) and cadmium(II) have been studied using thermogravimetry (TG) and differential scanning calorimetry (DSC). The reaction in which the complex loses one molecule of the ligand is found to be first order and the activation energy was calculated using established techniques. Using Dharwadkar and Karkhanavala's method, the values obtained were 25.65, 17.32, 25.22 and 20.95 kcal mole^?1, respectively. Infrared spectral studies of these complexes and intermediates provided information regarding the coordinating nature of the ligand 1,3-diaminopropan-2-ol in these complexes.     

Mechanism of diffusion and sorption of carbon dioxide in poly(vinyl acetate) above and below the glass transition temperature

The pressure dependence below 1 atm of the apparent diffusion and permeation coefficients were observed by using the permeation time lag method for carbon dioxide in poly(vinyl acetate), which has a glass transition near room temperature, at temperatures ranging from 8 to 50°C. Above the glass transition temperature, pressure dependence of the diffusion and permeation coefficient has not been observed; hence, Fick's law with a concentration independent diffusion coefficient applies. On the other hand, in the glassy state, the apparent diffusion coefficient shows pressure dependence. Moreover, the behavior of the pressure dependence does not show a clear curve in the ranges between 30°C to 17°C. Above 17°C, the apparent diffusion coefficients show discontinuities, but below 17°C increase with pressure is regular. Using the theoretical prediction of Paul, a computer was used in the numerical calculation to determine the true diffusion coefficient and other dual sorption parameters. p]The compensated diffusion coefficients controlled only by Henry's law dissolution was described by three straight lines with two intersection in the form of Arrhenius plots, which give good agreement with both our results for He and Ar and those of Meares. It is assumed that beside the dual sorption mechanism, another effect, for instance some relaxation effect may also contribute to the diffusion for carbon dioxide in poly(vinyl acetate) near the glass transition temperature region.     

Unusual influences of temperature and medium on the tacticity of radically polymerised poly(n-vinyl imidazole)

The tacticities of radical poly(N-vinyl imidazole)s prepared in several organic solvents, in water and at various values of pH and temperature have been investigated by ¹H and ¹³C-NMR. It seems most likely that high temperatures favour racemic placements over meso placements but that, at low pH, meso placements are favoured. Thus the changes in polymerisation rate with pH noted by others for this system are accompanied by changes in the stereochemistry of the resulting polymer.     

1H and 13C NMR study of the conformations of the atropisomers of some 1-(11-naphthyl)-2,4-dioxo-(or 2-thio-4-oxo)-hexahydro-pyriminides

The ¹H and ¹³C NMR spectra of the atropisomers of 6-(or 5-)-methyl-1-(1¹-naphthyl)-2, 4-dioxo-(or 2-thio-4-oxo)-hexahydro-pyrimidines, 1 to 4, are assigned on the basis of NOE and double resonance experiments. The syn-anti configurations of the isomers of 6-methyl-2,4-dioxo-pyrimidine follow from the close similarity of the NMR parameters to those observed with the isomers of the 6-methyl-2-thio derivative of known configuration. That of the 5-methyl derivatives was assigned from NOE and magnetic anisotropy effects of the naphthalene ring and of the (thio) amide group. Allylic strain between the naphthyl and 5-methyl groups makes the axial confomation prefered int he anti isomers. In the syn isomers, however, the equational and axial conformations are approximately equally populated, apparently due to interference between the remote benzene ring and the axial methyl group. The equatorial conformation is prepared with the 5-methyl derivatives.     

The chemistry and the stereochemistry of poly(N-alkyliminoalanes) : IX. Hexameric organoaluminum imides by reaction of (HAIN-iso-C3H7)6 with trialkylaluminums

(HAlN-iso-C₃H₇)₆ reacts with Al(CH₃)₃ or Al(C₂H₅)₃ to give compounds in which the hydridic hydrogens are partially or completely replaced by alkyl groups. The degree of alkylation depends on the reaction conditions and on the nature of the trialkylaluminum. Pure crystalline (CH₃AlN-iso-C₃H₇)₆, its crystallization product with [(CH₃AlN-iso-C₃H₇)₅(HAlN-iso-C₃H₇)] and a mixture of [(C₂H₅AlN-iso-C₃H₇)₄(HAlN-iso-C₃H₇)₂] isomers have been isolated. The reaction of Al(CH₃)₃ or Al(C₂H₅)₃ with iso-C₃H₇NH₂ gives tetramers (CH₃AlN-iso-C₃H₇)₄ and (C₂H₅AlN-iso-C₃H₇)₄.     

Preparation and thermal decomposition of dineophylplatinum(II) complexes; δ-hydrogen migration controlled by the nature of ancillary ligands.

The novel complexes L₂Pt(CH₂CMe₂Ph)₂ [L₂ = 1,5-cod, 2,2′-bipy, 2,2′-bipym; L = PEt₃, PPh₃] readily undergo cyclisations to afford L₂Pt(2-C₆H₄CMe₂CH₂) with elimination of tert-butylbenzene at rates dependent on L₂; reaction is fastest for the bulky monodentate Ph₃P, while chelating ligands generally decrease lability.     

Intramolecular excimer of DI(1-pyrenylmethyleneoxycarbonyl) alkanes

Intramolecular excimer emission of a series of di(1-pyrenylmethyleneoxycarbonyl)alkanes (n = 0–22) has been studied under photostationary conditions. The intramolecular excimer formation rate constant decreases monotonously with increasing number of methylene units of the chains in the low temperature region. The temperature dependence of the rate constant for each sample was studied to give an apparent activation energy of ca. 5 kcal/mol.