Method development and validation for the simultaneous determination of five selective serotonin reuptake inhibitors by capillary zone electrophoresis

Summary A capillary zone electrophoresis method is proposed for the separation of five antidepressants. Optimum conditions for the separation were investigated. A background electrolyte solution consisting of 40 mM phosphate buffer adjusted to pH 2.5, hydrodynamic injection, and a 28 kV separation voltage were used. Relative standard deviations (RSD) were <0.9% and <1.7% for migration time and corrected peak area (n=21), respectively. The detection limits for the five antidepressants ranged from 0.3 to 0.7 mg L⁻¹. The stability of the solutions, linearity, accuracy, and precision were examined during validation of the method. The method is rapid and sensitive, when it was tested for the analysis of pharmaceutical formulations the recoveries obtained were between 98 and 103% of the nominal content.     

Separation and simultaneous determination of quinolone antibiotics by capillary zone electrophoresis

Summary The potential of capillary zone electrophoresis has been investigated for the separation and quantitative determination of some quinolone antibiotics. The influence of different conditions, such as the nature and concentration of the electrophoretic electrolyte, on migration time, peak symmetry, efficiency and resolution was studied. A buffer consisting of 100mm HEPES adjusted to pH 8.5 containing 10% (v/v) acetonitrile was found to furnish a very efficient and stable electrophoretic system for the separation of exoxacin, ciprofloxacin, ofloxacin, oxolinic acid, nalidixic acid and pipemedic acid. A linear relationship between concentration and peak area for each compound was obtained in the concentration range 0.25–40 μg mL⁻¹; detection limits were approximately 0.25 ng mL⁻¹. It was demonstrated that the method can be used for the simultaneous determination of these six antibiotics in serum and urine samples.     

Capillary zone electrophoresis method for the determination of famotidine and related impurities in pharmaceuticals

A simple and rapid capillary zone electrophoresis (CZE) method with UV detection has been developed for the determination of famotidine and its potential impurities in pharmaceutical formulations. The electrophoretic separation of these compounds was performed using a fused silica capillary and 37.5mmolL(-1) phosphate buffer pH 3.5 as the electrolyte. Under the optimised conditions, six impurities could be resolved from the famotidine peak in less than 7min. The calibration curves obtained for the seven compounds were linear over the concentration range investigated (from 1.5 to 78.5microg mL(-1)). The intra- and inter-day relative standard deviations for the migration times and corrected peak areas were less than 2% and 5%, respectively. The detection limits were found to be 0.09microg mL(-1) for famotidine, and from 0.1 to 0.62microg mL(-1) depending on the impurities. The method has been successfully applied to the determination of famotidine in commercial dosage forms.     

Enantiomeric separation of synthetic 2,3-dihydroxy-3-phenylpropionate compounds by beta-cyclodextrin-modified capillary electrophoresis

A new capillary electrophoretic method was developed for enantiomeric separation and optical impurity analysis of three synthetic 2,3-dihydroxy-3-phenylpropionate compounds using native beta-cyclodextrin (beta-CD) as chiral selector and borate as a background electrolyte. The separation was carried out in uncoated capillary (58.5 cm x 75 microm I.D., effective length 48.5 cm). The results showed that beta-CD as the chiral selector exhibited good enantioselectivity and the baseline separation was obtained at pH 9.8, 200 mM borate buffer containing 1.7% beta-CD at applied voltage 15 kV and capillary temperature 20 degrees C within 15 min. The precision of each tested compound was less than 1.0% at migration time and 5.0% in corrected peak area and the accuracy of the method was in the range of 98.7-105%. Furthermore, the developed method was successfully applied to the determination of the undesirable trace (2S,3R)-(+)-form impurity in the synthetic (2R,3S)-(-)-2,3-dihydroxy-3-phenylpropionate samples.     

Anionic microemulsion to solvent stacking for on‐line sample concentration of cationic analytes in capillary electrophoresis

The common SDS microemulsion (i.e. 3.3% SDS, 0.8% octane, and 6.6% butanol) and organic solvents were investigated for the stacking of cationic drugs in capillary zone electrophoresis using a low pH separation electrolyte. The sample was prepared in the acidic microemulsion and a high percentage of organic solvent was included in the electrolyte at anodic end of capillary. The stacking mechanism was similar to micelle to solvent stacking where the micelles were replaced by the microemulsion for the transport of analytes to the organic solvent rich boundary. This boundary is found between the microemulsion and anodic electrolyte. The effective electrophoretic mobility of the cations reversed from the direction of the anode in the microemulsion to the cathode in the boundary. Microemulsion to solvent stacking was successfully achieved with 40% ACN in the anodic electrolyte and hydrodynamic sample injection of 21 s at 1000 mbar (equivalent to 30% of the effective length). The sensitivity enhancement factors in terms of peak height and corrected peak area were 15 to 35 and 21 to 47, respectively. The linearity R² in terms of corrected peak area were >0.999. Interday precisions (%RSD, n = 6) were 3.3–4.0% for corrected peak area and 2.0–3.0% for migration time. Application to spiked real sample is also presented.     

Capillary Electrophoretic Separation of Tricyclic Antidepressants Using 1‐Alkyl‐3‐Methylimidazolium‐Based Ionic Liquids as Background Electrolyte

A capillary electrophoretic (CE) method coupled with the use of 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (1E‐3MI‐TFB) ionic liquid as background electrolyte (BGE) has been developed for the simultaneous separation of nine tricyclic antidepressants, viz. amitriptyline (Ami), clomipramine (Clo), desipramine (Des), fluphenazine (Flu), imipramine (Imi), nortriptyline (Nor), promazine (Pro), thioridazine (Thi) and trimipramine (Tri). Resolution of TCAs with similar molecular structures and pK_a values was accomplished by minute manipulation of the electrophoretic velocities of TCAs via reversed electroosmotic flow (EOF) generated by adsorption of 1E‐3MI cations onto the capillary wall. The optimal separation was obtained with a 50 mM 1E‐3MI‐TFB as the sole BGE at pH 3. Symmetric peaks with efficiencies up to 2.4 × 10⁵ plates/m were achieved. RSD values on migration times and peak areas were in the ranges of 0.63–0.95% and 3.41–6.34% (n = 4), respectively. The role of different alkyl groups on the imidazolium cations was also investigated.     

A component tracking algorithm for accelerated and improved liquid chromatography-mass spectrometry method development

A method for tracking of sample components during liquid chromatography-mass spectrometry (LC-MS) method development has been proposed. The method manages to, fully automatically and without user intervention, find the chromatographic peaks in the data sets, discriminate them to sample components and track them when the separation conditions have been changed. The algorithm utilises the resolution obtained from all considered data sets and has the ability to discriminate the non informative parts. The technique has a great sensitivity even in cases where a majority of the tracked components cannot easily be spotted by means of traditional total ion chromatogram (TIC) or base peak chromatogram (BPC) representations. The method was tested on an experimental sample using six different columns and an average of 79% of the suggested sample components could be successfully tracked at a minimum area of 0.05% of the main component in the sample. 66 components with 79-92% of the total suggested component area were able to be tracked between all data sets. The method could be used to rapidly investigate selectivity during different types of separation conditions.     

Combining poly (methacrylic acid‐co‐ethylene glycol dimethacrylate) monolith microextraction and octadecyl phosphonic acid‐modified zirconia‐coated CEC with field‐enhanced sample injection for analysis of antidepressants in human plasma and urine

A method based on poly (methacrylic acid‐co‐ethylene glycol dimethacrylate) monolith microextraction and octadecylphosphonic acid‐modified zirconia‐coated CEC followed by field‐enhanced sample injection preconcentration technique was proposed for sensitive CE‐UV analysis of six antidepressants (doxepin, clozapine, imipramine, paroxetine, fluoxetine and chlorimipramine) in human plasma and urine. A poly(methacrylic acid‐co‐ethylene glycol dimethacrylate) monolithic capillary column was introduced for the extraction of antidepressants from urine and plasma samples. The hydrophobic main chains and acidic pendant groups of the monolithic column make it a superior material for extraction of basic analytes from aqueous matrix. After extraction, the desorption solvent, which normally provided an excellent medium to ensure direct compatibility for field‐enhanced sample injection in CE, was analyzed by CE directly. By the use of alkylphosphonate‐modified zirconia‐coated CEC for separation of the basic compounds of antidepressants, high separation efficiency and resolution were achieved because that both hydrophobic interaction between analytes and alkylphosphonate‐modified zirconia coat and electrophoretic effect work on the separation of antidepressants. The best separation was achieved using a buffer composed of 0.3 M ammonium acetate (adjusted to pH 4.5 with 1 M acetic acid) and 35% ACN v/v, with a temperature and voltage of 20°C and 20 kV, respectively. By applying both preconcentration procedures, LODs of 11.4–51.5 and 3.7–17.0 μg/L were achieved for the six antidepressants in human plasma and urine, respectively. Excellent method of reproducibility was found over a linear range of 50–5000 μg/L in plasma and urine sample.     

Kinetic study of gamma-glutamyltransferase activity by electrophoretically mediated microanalysis combined with micellar electrokinetic capillary chromatography

The use of capillary electrophoresis for the determination of gamma-glutamyltransferase (GGT) activity with gamma-glutamyl-p-nitroanilide (Glu-p-NA) as a substrate was investigated. The reaction velocity was quantified spectrophotometrically by the corrected peak area of the product p-nitroaniline (pNA) at 380 nm. Micelles composed of sodium deoxycholic acid were used in the background electrolyte in order to obtain a baseline separation between the substrate and the product. The presence of the micelles did not influence the enzymatic reaction. The electrophoretic system was used, not only for the separation and quantitation of the different reaction compounds but also for the in-capillary mixing of the enzyme and substrate plugs. This methodology is known as electrophoretically mediated microanalysis (EMMA). With the developed in-capillary activity assay an average Michaelis constant (K(M)) for GGT was calculated to be 2.09 mM (RSD = 7.3%, n = 3), a value consistent with previously reported values.     

Characterization of paromomycin sulfate by capillary electrophoresis with UV detection after pre-capillary derivatization

Summary A capillary electrophoretic method has been developed for determination of the components of the paromomycin mixture salt. Paromomycin was detected at 330 nm after pre-capillary derivatization witho-phthaldialdehyde and thioglycolic acid. The electrophoretic separation was performed in a fused-silica capillary at 25°C and 18kV with a background electrolyte comprising 40mm sodium tetraborate, 3mm β-cyclodextrin, and 12.5% (v/v) methanol. Although the analysis time was reduced to 10min, five peaks could be separated to baseline. The relative standard deviation of the ratios (peak area/internal standard peak area) was <5% for all peaks.     

Rapid analysis of anthracycline antibiotics doxorubicin and daunorubicin by microchip capillary electrophoresis

A simple and rapid method has been developed for the analysis of anthracycline antibiotics doxorubicin (DOX) and daunorubicin (DAU) in human serum using mirochip-based capillary electrophoresis (CE) with laser-induced fluorescence (LIF) detection. In this study, method development included studies of the effect of buffer pH, buffer concentration, organic solvents and separation voltage on sensitivity and separation efficiencies for the CE separation of DOX and DAU. Acetonitrile was found to have significantly improved the sensitivity and separation efficiency. The method was validated with regard to reproducibilities, linearity and limit of detection (LOD). The optimum electrophoretic separation conditions were 10 mM sodium tetraborate buffer at pH 9.5 with 40% acetonitrile (V/V) and a separation voltage of 2.1 kV. DOX and DAU were separated in 60 s under the optimum separation conditions. Linear relationships were obtained between the concentration and peak area (or peak height) in the 1–75 µg mL^{− 1} range and with the detection limits of 0.3 and 0.2 μg mL^{− 1} for DOX and DAU, respectively. The stability of both migration time and peak height of the analytes showed relative standard deviations of less than 5% (n = 9). The potential of this method was verified by spiking a human serum sample with the two drugs and analyzing the recovery ratios.     

Analysis of steroids by nonaqueous capillary electrophoresis

A simple method for the separation and determination of steroids (estradiol valerate, triamcinolone, levonorgestrel and ethinylestradiol) in single and compound tablets by nonaqueous capillary electrophoresis with ultraviolet (UV) spectrophotometric detection has been developed for the first time. After optimizing the electrophoretic parameters, including the nature of electrolytes and composition of organic solvent, the running buffers of methanol-acetonitrile (95: 5, v/v) containing 20 mM sodium acetate (pH 6.5) and methanol-acetonitrile (90: 10, v/v) containing 25 mM sodium acetate (pH 7.0) were found to be most suitable for determining estradiol valerate and triamcinolone, respectively. Reliable separation and simultaneous determination of levonorgestrel and ethinylestradiol were achieved in methanol containing 20 mM of ammonium acetate and 10 mM of sodium dodecyl sulfate (SDS). Tamoxifen was used as internal standard. Performance of the method, including migration time and peak area reproducibility, linearity, sensitivity and accuracy, were also evaluated. The limits of detection (S/N = 3) for four analytes were in the range of 9.8–19.5 μ g/mL. The relative standard deviations (RSD) of the migration times and peak areas of the analytes were in the range of 0.14–1.0% and 0.7–2.7% (intraday), 0.5–2.8% and 1.5–4.2% (interday), respectively. Within the tested concentration range, linear relationships between peak area ratios and concentrations of the analytes were obtained (correlation coefficients: 0.9987–0.9996). The method has been successfully applied to the determination of ingredients with recoveries over the range of 96.6–100.6%. The text was submitted by the authors in English.     

A micellar electrokinetic chromatography approach using diastereomeric derivatization and a volatile surfactant for the enantioselective separation of selenomethionine

A MEKC methodology with UV detection was developed for the enantioselective separation of selenomethionine (SeMet). The use of (+)‐1‐(9‐fluorenyl)ethyl chloroformate (FLEC) as chiral derivatization reagent to form SeMet diastereomers enabled their subsequent separation using ammonium perfluorooctanoate (APFO) as a volatile pseudostationary phase. The effect of APFO concentration and pH, temperature, injection volume, and derivatization conditions (time and FLEC/SeMet ratio) were evaluated in order to select the best separation conditions. A chiral resolution of 4.4 for DL‐SeMet was achieved in less than 6 min using 100 mM APFO at pH 8.5 as electrophoretic buffer. Satisfactory results were obtained in terms of linearity, precision (RSD from 3.4 to 5.1% for migration times and from 1.8 to 4.6% for corrected peak areas), accuracy, and LODs (3.1 × 10^?6 M and 3.7 × 10^?6 M for d and l enantiomers, respectively). The method was successfully applied to the determination of l ‐SeMet in food supplements.     

A new sequential injection analysis‐capillary electrophoresis system with amperometric detection

A novel and fully automated sequential injection analysis manifold coupled to a capillary electrophoresis apparatus with amperometric detection, is described. The sequential injection manifold was isolated from the high voltage by inserting an air plug into the circuit. Small buffer reservoirs were used to avoid the need to pump fresh buffer to the interface during the electrophoretic separation. No decoupling device was used to mitigate the interference from the high voltage electric field, instead the potential shift induced by the separation voltage, was accounted for. The new hydrodynamic injection method presented is based on the overpressure created in the circuit when a pinch valve is closed for a predetermined time. The injection method yields RSD values of peak height and area below 2.55 and 1.82%, respectively, at different durations of valve closure (n = 5). The capillary and working electrode alignment was achieved by adapting a commercial available capillary union. When the electrode was replaced, the alignment method proved to be very reliable, yielding RSD values of peak height and area lower than 2.64 and 2.08%, respectively (n = 8). Using this system with a gold microelectrode, dopamine, and epinephrine could be quantified within the concentration range of 1–500 μM and detected at a concentration of 0.3 μM. The methods here presented could be applied for the development of new capillary electrophoresis systems with amperometric detection and/or to the design of fully automated systems for online process monitoring purposes.     

Comparative study of different approaches to the determination of robustness for a sensitive-stacking capillary electrophoresis method. Estimation of system suitability test limits from the robustness test

A robustness study for a sensitive-stacking capillary electrophoresis method based on “acetonitrile-stacking” was carried out. Ten variables (pH, acetonitrile and triethanolamine in the buffer, injection time, injection pressure, acetonitrile and NaCl in the sample, capillary and tray temperature and separation voltage), whose levels were varied by 10% around the nominal level, were examined by a Plackett–Burman design (two-level design). The effects on corrected peak area and resolution (responses) were calculated and interpreted using three statistical approaches: dummy variables, distribution effects (Dong’s algorithm) and calibration curve. Dong’s method was found to be the most suitable to evaluate the robustness, since it considers qualitative (resolution) and quantitative (corrected peak area) responses and does not need a minimum number of dummy variables in the experimental design. From these studies, we can deduce that the first four variables were significant at 10% around the nominal level, and therefore a new design was made with those four variables at 5% nominal level. Then, only two variables proved to be significant for the resolution between some peaks, so the system suitability test limits were defined for these resolutions.     

Separation of phenolic acids in soil and plant tissue extracts by co-electroosmotic capillary electrophoresis with direct UV detection

Summary A capillary zone electrophoretic method for the analysis of phenolic acids in soil and plant extracts was developed with direct UV detection using a phosphate electrolyte solution. The electrophoretic separation required the phenolic acids to be charged at a pH above their pKa in order to achieve their migration towards the anode. Electroosmotic flow (EOF) was reversed in direction by adding tetradecyltrimethylammonium bromide (TTAB). Factors affecting the separation selectivity, including the buffer pH and EOF modifiers, were investigated systematically. Eight phenolic acids were separated and detected in 10 min using an electrolyte containing 25 mM phosphate, 0.5 mM TTAB and 15% acetonitrile (v/v) at pH of 7.20. Linear plots for the test phenolic acids were obtained in a concentration range of 0.01–1 mM with detection limits in the range of 1.0–7.0 μM. The recoveries ranged from 92.8 to 102.3% in soil and plant tissues samples spiked at 100 μM and the relative standard deviation based on the peak area were ranged 2.0 to 4.5%. The proposed method was used for the determination of phenolic acids in plant tissue and soil extracts with direct injection.     

Fast in-line bottom-up analysis of monoclonal antibodies: Toward an electrophoretic fingerprinting approach

For their characterization and quality control, monoclonal antibodies are frequently analyzed at the bottom-up level to generate specific fingerprints that can be used to tackle post-translational modifications or ensure production consistency between lots. To circumvent time-consuming and labor-intensive off-line sample preparation steps, the implementation of integrated methodologies from sample preparation to separation and detection is highly valuable. In this perspective, capillary zone electrophoresis appears as a choice technique since the capillary can subsequently be used as a vessel for sample preparation and electrophoretic discrimination/detection of the reaction products. Here, a fast in-line methodology for the routine quality control of mAbs at the bottom-up level is reported. Simultaneous denaturation and reduction (pretreatment step) were conducted with RapiGest® surfactant and dithiothreitol before in-line tryptic digestion. Reactant mixing was realized by transverse diffusion of laminar flow profile under controlled temperature. In-line digestion was carried out with a resistant trypsin to autolysis. The main parameters affecting the digestion efficiency (trypsin concentration and incubation conditions) were optimized to generate mAb electrophoretic profiles free from trypsin interferences. An acidic MS-compatible BGE was used to obtain high resolution separation of released peptides and in-line surfactant cleavage. The whole methodology was performed in less than two hours with good repeatability of migration times (RSD = 0.91%, n = 5) and corrected peak areas (RSD = 9.6%, n = 5). CE-fingerprints were successfully established for different mAbs and an antibody-drug conjugate.     

Electrochemical detection for microscale analytical systems: a review

This paper describes the development of an electrophoretic method used to analyse diuretics, and its use in the analysis of pharmaceutical formulations. Chlorthalidone, furosemide, hydrochlorothiazide and triamterene were separated in 5 min by micellar electrokinetic capillary chromatography using a carrier containing sodium dodecylsulphate as surfactant, and were subsequently detected spectrophotometrically using a diode-array detector. The limits of detection (S/N=3) were in all cases less than 1.2 mugml(-1) for all compounds. Satisfactory repeatability was obtained for migration times (<1.6%) and corrected peak areas (<5.3%) in the analysis of pharmaceutical formulations. The reproducibility was less than 4% for all samples tested. The average recoveries obtained, which ranged between 97 and 100%, testify to the accuracy of the proposed method.     

Study of the separation and determination of monosaccharides in soluble coffee by capillary zone electrophoresis with electrochemical detection

A simple, fast and reliable method, based on capillary electrophoresis with electrochemical detection, for the separation and determination of six monosaccharides, namely glucose, galactose, arabinose, fructose, xylose and ribose, in soluble coffees was developed. A copper disk electrode was used as the working electrode. The optimum conditions for separation and detection were 50 mmol L-1 sodium hydroxide buffer (pH 12.7), separation voltage 5 kV and detection potential 0.65 V (vs. Ag/AgCl). The linear ranges were from 5.0 x 10(-3) to 0.5 mmol L-1 for all six sugars. All regression coefficients were > 0.99. The detection limits for all the sugars were 1.0 x 10(-3) mmol L-1. The RSD of the peak current was < 4.2% (n = 5). The proposed method was applied directly to the separation and determination of the six sugars without prior derivatization, and the assay results were satisfactory.     

Analysis of baclofen by capillary electrophoresis with laser-induced fluorescence detection

A new analytical method for baclofen (4-amino-3-p-chlorophenylbutyric acid) based on capillary electrophoretic separation and laser-induced fluorescence detection has been developed. Naphthalene-2,3-dicarboxaldehyde was used for precolumn derivatization of the non-fluorescent drug. Optimal separation and detection were obtained with an electrophoretic buffer of 50 mM sodium borate (pH 9.5) and a He-Cd laser (excitation at 442 nm, emission at 500 nm). Linearity (r > or = 0.99) over three orders of magnitude was generally obtained and the concentration limit of detection was in the nanomolar level. Coupled with a simple cleanup procedure, the method was successfully applied to the analysis of baclofen in human plasma. Recovery of spiked baclofen in plasma was 98%. The relative standard deviation values on peak size and migration time were 7.9% and 0.4%, respectively. The limit of detection of baclofen in plasma was 10 ng/ml.