The role of mobile-phase pH in the determination of catecholamine-related compounds by reversed-phase liquid chromatography with amperometric detection

Summary A study was conducted for the optimization of the reversed-phase high performance liquid chromatographic separation of different types (acidic, basic, amphoteric and neutral) of catechol-related compounds by varying the pH. For pH to be used as the optimizing parameter, its effects on retention, peak width and peak shape had to be investigated. Therefore, the pH dependence of the amperometric detector response, as measured by the oxidation peak height or peak area, was taken into account.     

Effects of pH in reversed-phase liquid chromatography

The effects of concomitant variations in pH and organic modifier concentration on retention, efficiency and peak symmetry are considered for reversed-phase liquid chromatography (RPLC) on octadecyl-modified silica (ODS) columns. A number of factors are discussed, which make the systematic exploitation of pH effects in RPLC more complicated than the optimization of solvent composition. If the pH is varied, a second factor (usually the concentration of organic modifier) will need to be varied simultaneously to maintain retention (capacity factors) in the optimum range. When pH is considered as a parameter in RPLC, not only its effects on retention, but also the variations in efficiency (plate count) and peak shape (asymmetry) need to be considered. These parameters turn out to vary drastically between individual solutes and between different experimental conditions. The results of a study involving a number of acidic, basic and neutral solutes, two different ODS columns and mixtures of either methanol or acetonitrile with aqueous buffers are reported. In the earlier part of the study, using methanol as the organic modifier, reproducible data for retention, peak width and peak symmetry were obtained and these data are reported. In the later part of the study, using acetonitrile, a gradual change in retention as a function of time was observed, this effect coinciding with a decrease in column efficiency. It is concluded that ODS columns are subject to considerable degradation during studies in which the pH is varied. Although this effect can be described mathematically, the preferred solution is thought to be the use of pH-stable columns.     

Evaluation of a new polymeric stationary phase with reversed-phase properties for high temperature liquid chromatography

The performance of a polymeric stationary phase with reversed-phase properties (ET-RP1) was evaluated for LC separations at elevated temperature. The most significant observation was that the reduced plate height (h) decreased from 3.4 at 25 °C (optimal flow 0.5 mL/min) to 2.4 at 150 °C (optimal flow 2.5 mL/min) which is comparable to the efficiency obtained with silica-based reversed-phase columns of 4.6 mm ID operated at 0.8 mL/min. The phase showed no deterioration after long use at 150 °C within the pH range 1–9. Catalytic activity originating from the stationary phase material, e.g. as experienced on zirconium columns operated at elevated temperature, was absent. The performance of ET-RP1 is illustrated with the analysis of some pharmaceutical samples by LC and LC–MS. Operation at elevated temperature also allows to reduce the amount of organic modifier or to replace acetonitrile and methanol by the biodegradable ethanol.     

A novel silica-based column packing for reversed-phase HPLC of basic compounds

Summary A novel bonded phase for reversed-phase HPLC was synthesized in two steps. Octylamine was first reacted with β-(3,4-epoxycyclohexyl)ethyltrimethoxysilane (β-ECTS) and then the intermediate product was coupled onto porous silica. The prepared packing was characterized by elemental analysis, solid-state¹³C NMR and Fourier transform infrared (FT-IR). Chromatographic evaluations were carried out by using a mixture of organic compounds including acidic, basic and neutral analytes and methanol-water as binary mobile phase. The results showed that the stationary phase has excellent chromatographic properties and is resistant to hydrolysis between pH=2≈8. It can be used efficiently for the separation of basic compounds.     

Analysis of basic compounds by reversed-phase high-performance liquid chromatography using hybrid inorganic/organic phases at high pH

The retention and mass overload of five bases and a quaternary ammonium compound were studied on a bridged ethyl hybrid inorganic/organic phase (XBridge C18) over a pH range 2.7-12.0 using acetonitrile-phosphate and carbonate buffers. Some comparisons were drawn with results on a methyl hybrid (XTerra) phase. At low pH, rapid mass overload was observed with severe decreases in efficiency as sample mass was increased over the range 0.04-5 microg of solute. At intermediate pH (swpH 7.0), generally good peak shapes for small sample mass were still obtained on the ethyl hybrid, but with somewhat increased tailing of bases compared with swpH 2.7. At higher pH (swpH 10), good peak shape and improved loadability were obtained for moderately strong bases, due to their occurrence mostly as neutral species. However, stronger bases gave poor efficiency, attributed to interaction of the charged basic solute with increasingly ionised column silanol groups. Results were broadly similar on the methyl hybrid at swpH 10. At swpH 11, unusual profiles of increasing followed by decreasing efficiency were obtained on the ethyl hybrid for some bases as sample mass was increased; improved results were obtained at swpH 12. While the column loadability increased substantially at the highest pH studied, tailing for small sample mass was still more severe than at low pH, even though all compounds were <1% ionised in the mobile phase.     

Determination of UV-transparent compounds by liquid chromatography using the UV detector

An indirect UV photometric detection technique is described in which a low concentration of a UV-absorbing compound (UVAC) is added to the mobile phase in reversed phase liquid chromatography, thereby making it possible for non UV-absorbing compounds such as the lower alcohols to be detected by the UV detector. This happens because the injected analyte may extract a portion of the UV absorbing compound from the mobile and/or stationary phase and the complex is co-eluted as a positive peak at the retention time of the analyte. Alternatively, the injected analyte may appear as a negative peak if the UV-absorbing compound is transferred to the mobile and stationary phases. In any case, the injected compound appears either as a positive or negative peak depending on the relative polarities and concentrations of all the compounds in the system. In addition, the resulting excess or deficiency of detection agent in the stationary phase is eluted separately as a positive or negative peak, indicating that the system has returned to equilibrium. In the work described herein, the chromatographic conditions and variables of the indirect photometric technique were studied to develop a quantitative HPLC method for UV-transparent compounds. It was found that under optimal conditions it is possible to determine some analytes quantitatively at concentrations as low as 0.05%.     

Detection by ion-pairing probes in reversed-phase liquid chromatography

Summary Compounds without own detector response can be detected and quantified by a UV-absorbing or fluorescent, ion-pairing probe in reversed-phase liquid-solid systems. Charged as well as uncharged samples give response by affecting the distribution of the probe between the phases. The probe is usually a hydrophobic organic ion. It is included in the mobile phase, which also contains a counter ion and an ion of the same charge as the probe, both fairly hydrophilic. The choice of properties and concentrations of the hydrophilic ions is essential for the response since too low and too high distribution of the mobile phase ions to the adsorbent will make the system insensitive. It is with UV-absorbing probes possible to get a response corresponding to a molar absorptivity of more than 3000 for ionic samples. Fluorescent probes have given 3–5 times higher sensitivity. Uncharged compounds give as a rule lower response. A combination of two UV-absorbing probes with different charge gives a considerable improvement of the response for samples with low retention. A simplified theoretical model for the detector response is suggested on the basis of detailed studies of the concentration changes in the eluted mobile phase.     

A simple high pH liquid chromatography-tandem mass spectrometry method for basic compounds: application to ephedrines in doping control analysis

Solvent systems for use with LC-MS often result in a compromise between chromatographic performance and mass spectrometric detection, exemplified here by a LC-MS/MS method development for the analysis of ephedrines in doping control. Ephedrines, frequently found in therapeutic and nutritional preparations, are among the most commonly administered doping agents in competitive sport. Improved separation of these hydrophilic, basic compounds, some of which are diastereoisomers, is achieved in reversed-phase LC by the use of a high pH mobile phase in order to suppress analyte ionisation, and thus alter their polarity, resulting in reduced peak tailing and enhanced retention. However, when coupled to an ESI-MS detector, this eluent composition generated a non-linear and poorly reproducible signal. APCI yielded greater stability and reproducibility and is here presented as an ion source for the analysis of basic compounds under conditions that suppress their ionisation. Errors as large as 49.3% were observed with ESI, compared with 15.4% generated using APCI, for pseudoephedrine over the calibration range (25-400 μg/mL) in urine with a simple dilution and injection of samples. These data highlight the importance of suitable MS conditions for stable performance, necessary for accurate quantification, without undue compromise to the LC separation.     

除草剂双苯唑快的反相高效液相色谱法分析

采用反相高效液相色谱法分析除草剂——双苯唑快,色谱柱为Ｓｅｌｅｃｔｏｓｉｌ５Ｃ１８不锈钢柱,检测波长为２５４ｎｍ,用Ｖ（甲醇）Ｖ（水）＝６０４０（ｐＨ３）为流动相。方法的变异系数为０．４１％,平均回收率为９９．３４％,线性相关系数为０．９９９９。方法快速、准确。     

Optimizing separations in reversed-phase liquid chromatography by varying pH and solvent composition

Summary An interpretive optimization procedure in which pH can be one of the variables is presented with the emphasis on optimizing separations. When varying the pH in reversed-phase liquid chromatography the retention of ionogenic solutes will change. Thus, the selectivity between ionogenic and neutral solutes or between ionogenic solutes mutually can be optimized. However, pH also greatly affects the efficiency (plate count) and peak shape (asymmetry). Optimum selectivity (i.e. large differences in retention times) may be observed under conditions where peaks are broad and asymmetrical. Thus, it is essential to simultaneously consider retention, peak width and peak shape and their effects on separation (effective resolution) in pH-optimization studies. A procedure in which this is done is presented and applied to optimizing the separation of a synthetic mixture of selected pharmaceuticals. After initial experiments to establish the parameter space (boundaries for pH and binary methanol — water composition), twelve experiments are performed according to a 3×4 experimental design. At each loaction the retention, peak height, peak area and peak symmetry are recorded for each solute. These data are then used to build models for each of the four characteristics and for each solute. From this set of models the response surface, describing the quality of separation as a function of pH and composition, can be calculated. A variety of optimization criteria (quantifying quality of separation) can be used. The optimum corresponds to the highest point on the response surface.     

高效液相色谱法分析硫双灭多威

研究了用高效液相色谱分析杀虫剂硫双灭多威的方法。在反相ＯＤＳ柱上,用甲醇－水作流动相,紫外检测器检测,以邻苯二甲酸二甲酯作内标定量。方法快速、准确,重现性好,线性范围宽,变异系数为０．１８％,回收率为９９．８９％,色谱分析周期仅为８ｍｉｎ。     

Selective retention of basic compounds by metal aquo‐ion affinity chromatography

A novel metal aquo‐ion affinity chromatography has been developed for the analysis of basic compounds using heat‐treated silica gel containing hydrated metal cations (metal aquo‐ions) as the packing material. The packing materials of the metal aquo‐ion affinity chromatography were prepared by the immobilization of a single metal component such as Fe(III), Al(III), Ag(I), and Ni(II) on silica gel followed by extensive heat treatment. The immobilized metals form aquo‐ions to present cation‐exchange ability for basic analytes and the cation‐exchange ability for basic analytes depends on pK_a of the immobilized metal species. In the present study, to evaluate the retention characteristics of metal aquo‐ion affinity chromatography, the on‐line solid‐phase extraction of drugs was investigated. Obtained data clearly evidence the selective retention capability of metal aquo‐ion affinity chromatography for basic analytes with sufficient capacity.     

Use of unmodified silica with buffered aqueous mobile phase mixtures for selective chromatography of basic drugs

Summary The characteristic selectivity of unmodified silica using mixed aqueous-methanolic mobile phase systems for the separation of basic drugs was studied. It was found that low buffer concentration-high methanol eluents show increased chromatographic performance over mobile phase systems lower in methanol and higher in ion strength. Regarding an assumed ion-exchanger retention mechanism, the capacity factors of an amino group containing drugs is primarily dependent on the concentration of the cation and the pH-value of the eluent. By increasing the pH-value of the eluent, elution order of primary and secondary to tertiary amines is reversed. By only using eluents with buffering capability, a very high stability and reproducibility of retention of the basic drugs could be observed. Comparing three different brands of unmodified silica materials, with different pore size and specific surface area, only small differences in the selectivity for the tested drugs could be found.     

Design of mobile phase composition for liquid chromatography with an internal pH gradient

Summary A method is suggested for calculating the mobile phase composition for ion exchange chromatography with an internal pH gradient. An internal pH gradient of the desired steepness can be achieved providing the titration curve of the sorbent is known. The procedure has been verified by use in the design of a mobile phase composed from few anionic buffers for generation of internal pH gradient on a microcolumn packed with a cation exchanger with carboxylic functional groups.     

Methodology for dyes purification by preparative bidimensional offline reversed-phase high-performance liquid chromatography separation based on mobile phase pH change: Case study of Justicia spicigera

The extensive characterization of the natural dyes involves the purification of their colored compounds for their structural analysis and stability studies. As most natural compounds being ionizable, herein is presented the optimization of an easy and affordable preparative bidimensional offline reversed-phase high-performance liquid chromatography purification based on mobile phase pH change. At the analytical scale, several combinations of stationary phases and mobile phases at different pH values were investigated first. The orthogonality between the dimensions was quantitatively evaluated using the nearest-neighbor distance approach. The optimized separation method was transferred to the preparative scale for the successful isolation of two colored compounds from Justicia spicigera, a traditional dye plant from Central America. They were identified as perisbivalvine B (2-amino-8-hydroxy-7-methoxy-3H-phenoxazin-3-one) and one of its derivatives, also found in another tinctorial plant species, Peristrophe bivalvis growing in Asia.     

Enantioselective separation of biologically active basic compounds in ultra-performance supercritical fluid chromatography

The enantioseparation of basic compounds represent a challenging task in modern SFC. Therefore this work is focused on development and optimization of fast SFC methods suitable for enantioseparation of 27 biologically active basic compounds of various structures. The influences of the co-solvent type as well as different mobile phase additives on retention, enantioselectivity and enantioresolution were investigated. Obtained results confirmed that the mobile phase additives, especially bases (or the mixture of base and acid), improve peak shape and enhance enantioresolution. The best results were achieved with isopropylamine or the mixture of isopropylamine and trifluoroacetic acid as additives. In addition, the effect of temperature and back pressure were evaluated to optimize the enantioseparation process. The immobilized amylose-based chiral stationary phase, i.e. tris(3,5-dimethylphenylcarbamate) derivative of amylose proved to be useful tool for the enantioseparation of a broad spectrum of chiral bases. The chromatographic conditions that yielded baseline enantioseparations of all tested compounds were discovered. The presented work can serve as a guide for simplifying the method development for enantioseparation of basic racemates in SFC.     

Analysis of triacylglycerol positional isomers by silver ion high performance liquid chromatography

Silver ion chromatography, utilizing two commercially available HPLC columns connected in series, was used to separate a variety of triacylglycerol positional isomers. The isomers had a fatty acid composition of ABA and AAB, where A and B were fatty acids containing zero to three double bonds. Isocratic solvent systems of 0.5% to 1.0% acetonitrile in hexane were used to separate the triacylglycerol isomers. This methodology can be used to rapidly determine the isomeric purity of synthesized or isolated triacylglycerols and to isolate specific positional isomers.     

高效液相色谱手性流动相法拆分酮基布洛芬对映体

以Lichrospher C18为分析柱, 将β-环糊精、2,6-二甲基-β-环糊精、2,3,6-三甲基-β-环糊精分别作为手性流动相添加剂, 系统地研究了R,S-酮基布络芬对映体在HPLC系统中的拆分. 建立了以2,3,6-三甲基-β-环糊精为手性流动相添加剂分离R,S-酮基布络芬对映体方法.     

The challenges of the analysis of basic compounds by high performance liquid chromatography: Some possible approaches for improved separations

This review considers some of the difficulties encountered with the analysis of ionised bases using reversed-phase chromatography, such as detrimental interaction with column silanol groups, and overloading which both lead to poor peak shapes. Methods of overcoming these problems in reversed-phase (RP) separations, by judicious selection of the column and mobile phase conditions, are discussed. Hydrophilic interaction chromatography is considered as an alternative method for the separation of some basic compounds.