Er3+/Yb3+共掺NaYF4/LiYF4微米晶体的上转换荧光特性

采用水热法成功制备了Er³⁺/Yb³⁺共掺杂的NaYF₄和LiYF₄微米晶体. 通过X射线衍射仪和环境扫描电子显微镜对样品的晶体结构及形貌进行表征. 实验结果表明: 六方相NaYF₄微米晶体为棒状结构, 而四方相LiYF₄微米晶体则为八面体结构. 在近红外光980 nm激发下, NaYF₄:Yb³⁺/Er³⁺和LiYF₄:Yb³⁺/Er³⁺ 微米晶体均展现出很强上转换荧光发射. 且NaYF₄:Yb³⁺/Er³⁺微米晶体的荧光发射强度大约是LiYF₄:Yb³⁺/Er³⁺微米晶体的2倍, 但红绿比明显较低. 根据荧光光谱, 并借助激光光谱学及发光动力学深入探讨基质变化及表面修饰剂乙二胺四乙二酸(EDTA)对荧光特性的影响. 实验结果发现: 影响荧光强度的主要因素是基质环境的局域对称性, 而导致不同红绿比则是由于样品表面较多的EDTA分子所引起. Er³⁺掺杂的NaYF₄和LiYF₄ 微米晶体呈现出很强的绿光发射可被应用于全色显示, 荧光粉和微光电子器件中.     

荧光粉MPO4：Eu3+,Bi3+/Tb3+ (M=La,Gd,Y) 的结构及发光性能研究

采用高温固相法合成了一系列MPO₄：Eu³⁺,Bi³⁺ （M=La,Gd,Y）及 MPO₄：Tb³⁺ （M=La,Gd,Y）荧光粉材料,用X射线衍射（XRD）仪对样品结构进行了表征。所合成的LaPO₄和GdPO₄属单斜晶系,而YPO₄属体心立方晶系。用Diamond软件对结构进行分析并绘出了晶胞结构。对样品发光性质的研究结果表明,虽然MPO₄（M=La,Gd,Y）均属于正磷酸盐,但由于晶格结构不同,其发光性质也不同。立方晶系的YPO₄更有利于掺入其中的稀土离子的发光,Bi³⁺离子的引入能够明显改善样品的发光性能。     

On the energy transfer from Tb to Eu in LiTb1−xEuxP4O12

The undoped stoichiometric materials LiTbP₄O₁₂ and LiEuP₄O₁₂ show effective green Tb³⁺ and red Eu³⁺ luminescence, respectively. Both systems are fully mixable, which offers the possibility of examining the energy transfer from Tb³⁺ to Eu³⁺ in the complete system of LiTb_1−xEu_xP₄O₁₂. As the distance of the rare earth ions is large enough to exclude exchange interaction in these materials, only multipolar interaction is to be expected. Dealing only with forbidden f–f transitions it is possible to produce both Tb³⁺ and Eu³⁺ luminescence at the same time having a suitable Eu³⁺ concentration.     

BaGd2(MoO4)4:Tb3+,Eu3+荧光粉的 发光特性与能量传递机理

利用高温固相法制备了BaGd_2(MoO_4)_4∶Tb~(3+)与BaGd_2(MoO_4)_4∶Tb~(3+),Eu~(3+)荧光粉,并借助于X射线衍射(XRD)、激发光谱、发射光谱及荧光衰减曲线对样品的结构及发光性能进行了表征。在290 nm激发下,BaGd_2(MoO_4)_4∶Tb~(3+)样品在550 nm处具有较强的绿光发射,表明该样品可用作绿色荧光粉。Tb~(3+)离子的最佳掺杂浓度为50%,电偶极间相互作用是引起浓度猝灭效应的主要原因。当在BaGd_2(MoO_4)_4∶Tb~(3+)荧光粉中共掺入Eu~(3+)离子后,可同时观测到Tb~(3+)与Eu~(3+)离子的特征发射峰。随Eu~(3+)掺杂浓度的升高,Tb~(3+)离子的发光强度逐渐下降,而Eu~(3+)离子的发光强度逐渐增加。根据BaGd_2(MoO_4)_4∶Tb~(3+),Eu~(3+)中Tb~(3+)离子的荧光寿命计算了Tb~(3+)与Eu~(3+)离子间的能量传递效率,并根据荧光寿命与激活离子掺杂浓度的关系证实了能量传递机制为电偶极间相互作用。     

Tb/Eu 共掺锌硼磷酸盐白光发光玻璃的制备及其发光性能

采用熔体冷却法,通过控制玻璃基质组成及稀土离子添加量,制备了Tb、Eu单掺和Tb/Eu共掺的锌硼磷酸盐低熔点发光玻璃。测试了样品的红外光谱、吸收光谱、激发与发射光谱和荧光寿命,并计算CIE色坐标,研究了材料的微观结构及发光性能。结果表明：样品中部分Eu³⁺被还原为Eu²⁺,在380 nm波长激发下,Tb/Eu共掺发光玻璃同时出现Eu³⁺红光、Tb³⁺绿光和Eu²⁺蓝光的特征发射。增加基体中B₂O₃含量能强化玻璃网络结构,并改变Eu²⁺/Eu³⁺比例。发射光谱和荧光寿命测试表明,共掺的发光玻璃中存在Eu²⁺→Eu³⁺,Eu²⁺→Tb³⁺和Tb³⁺→Eu³⁺的能量传递。改变Tb、Eu的掺杂浓度能够有效改变发光玻璃的发光强度和颜色,最终得到色坐标为（0.318 7,0.286 1）、色温6 480 K的发光玻璃。     

稀土离子(Eu3+,Tb3+,Ce3+)掺杂ZnAl2O4/SiO2微晶玻璃的制备与发光性能

采用凝胶法分别制备出4.5ZnO-5.5Al₂O₃-90SiO₂(ZAS)以及ZAS[DK]:RE³⁺ (RE=Eu,Tb,Ce) 透明微晶玻璃。利用X射线衍射仪(XRD)、透射电子显微镜(TEM)和荧光光谱仪(PL)等测试手段,研究了稀土离子掺杂浓度对ZAS微晶玻璃的结构和发光性能的影响。XRD结果表明,ZAS[DK]:RE³⁺ (RE=Eu,Tb,Ce)微晶玻璃包含ZnAl₂O₄晶相和SiO₂非晶相,ZnAl₂O₄平均晶粒尺寸约为30 nm,稀土离子的掺杂没有显著改变原来的ZnAl₂O₄晶体结构。TEM结果表明,900 ℃时ZnAl₂O₄从ZAS体系中析出。PL光谱显示,Eu³⁺ 存在 ⁵D₀→⁷F₂跃迁,ZAS[DK]:Eu³⁺在611 nm 处发出强烈的红色光;由于Tb³⁺ 的⁵D₄→⁷F₅ 跃迁,ZAS[DK]:Tb³⁺在541 nm 处发出明亮的绿色光;ZAS[DK]:Ce³⁺ 在381 nm处显示了蓝光发射,对应于Ce³⁺ 的5d→4f 轨道跃迁。ZAS[DK]:RE³⁺ (RE=Eu, Tb, Ce)的PL发射光谱存在着浓度猝灭现象,Eu³⁺、Tb³⁺ 和Ce³⁺的最佳单掺杂摩尔分数分别为20%、20%和3%。CIE色度图表明,ZAS[DK]: RE³⁺ (RE=Eu,Tb,Ce)的色坐标分别位于红光、绿光和蓝光区域。实验结果表明,ZAS:RE³⁺ (RE=Eu,Tb,Ce) 微晶玻璃是一种良好的可用于全色显示的白光LED材料。     

Scintillation properties of PbWO4 crystals doped with the rare-earth ions

In PbWO₄(PWO) crystals grown by Czochralski method the influence of atmosphere of the growth (O₂, air) and doping with the rare-earth ions of different types (A³⁺=Lu³⁺, Gd³⁺,Tb³⁺,Eu³⁺ as well as doubly doped A³⁺–Li⁺) on light yield and luminescence decay were analyzed. PWO scintillator with the ultra-fast (τ=0.5 ns) main component of luminescence decay (87% of total light yield) was obtained using the O₂-growth atmosphere and doping by Eu₂O₃ at a concentration of 5000 ppm. It is concluded that the decrease of decay constant of the main scintillation component is the result of the resonant energy transfer between the centers of “blue” PWO luminescence (λ_max=420 nm) and the 4f–4f-transitions of Eu³⁺ ions in this spectral region.     

纳米SrHPO4：RE（RE=Eu3+或Tb3+）磷光体的水热合成与光谱特性

利用水热法合成了α-SrHPO₄：RE（RE=Eu³⁺,Tb³⁺）纳米磷光体,并研究了材料的形貌与光谱特性。α-SrHPO₄纳米粒子为长度90~200 nm的棒状结构,直径为24~36 nm。Eu³⁺和Tb³⁺的掺杂均会降低α-SrHPO₄的结晶度,并减小其长径比。α-Sr_0.97HPO₄：0.03Eu³⁺在395 nm近紫外光的激发下,存在分别由⁵D₀→⁷F₁和⁵D₀→⁷F₁₂跃迁引起的590 nm和614 nm发射峰,最终发射橙红光。α-Sr_0.97HPO₄：0.03Tb³⁺在217 nm近紫外光的激发下,存在由⁵D₄→⁷F₅跃迁引起的543 nm绿光发射。     

Photoluminescence and photostimulated luminescence in the X-ray storage phosphor BaBr2 doped with cerium

In orthorhombic BaBr₂ : Ce³⁺ two kinds of luminescence bands at room temperature have been attributed to charge-compensated Ce³⁺ centres. One type was associated with potassium (or some other monovalent cation) on a neighbouring Ba site and another one associated with an unidentified defect. A third kind of emission, observed only as low temperature photoluminescence (PL), is ascribed to isolated Ce³⁺ ions. The charge-compensated Ce³⁺ complexes are active both in PL and photostimulated luminescence (PSL) following X-ray irradiation. The PSL is nearly as efficient as in the case of the commercially used X-ray storage phosphor BaFBr:Eu²⁺. The X-ray induced electrons are trapped in F-type centres whose band position is characteristic for the nearby Ce complex. As shown by the fingerprint character of the PSL itself, the hole partner in the recombination is also associated or identical with the same Ce complex.     

Tm-to-Ho resonant and nonresonant energy transfer in LiYF4

Absorption and luminescence measurements of Tm³⁺ and Ho³⁺ ions in LiYF₄:Tm³⁺, LiYF₄:Ho³⁺ and LiYF₄:Tm³⁺, Ho³⁺ crystals were carried out. The data collected were used to determine the Ho³⁺ absorption coefficient integral for ⁵I₈→⁵I₇ transition, and the overlap integral between the normalized Tm³⁺ luminescence spectrum due to the ³F₄→³H₆ transition and the Ho³⁺ absorption band due to ⁵I₈→⁵I₇ transition. The relevant critical transfer distance (R_o), that gives a measure of the Tm³⁺–Ho³⁺ coupling, was determined considering the Förster type interaction between the ions. It was found to be 22.5 Å and 28.8 Å at 300 and 78 K, respectively.     

Simultaneous excitation of Ce and Eu ions in Tb3Al5O12

Y₃Al₅O₁₂:Ce³⁺ (YAG:Ce) and Tb₃Al₅O₁₂:Ce³⁺ (TAG:Ce) both show the typical Ce³⁺ ion luminescence of the allowed Ce³⁺ d–f transition. Eu³⁺ codoping, however, reveals different results for both matrices: in YAG:Ce,Eu, only the luminescence of the Ce³⁺ ion occurs by excitation within the Ce³⁺ absorption bands. Here, the Eu³⁺ luminescence cannot be sensitized by the Ce³⁺ ion. But in TAG:Ce,Eu, both Ce³⁺ and Eu³⁺ luminescence are measured at several excitation wavelengths: an excitation within the Tb-sublattice results in both Ce³⁺ and Eu³⁺ luminescence, which is not surprising as an energy transfer from Tb³⁺ to Ce³⁺ and Eu³⁺ is well known in literature. In addition, an excitation in the lowest 5d level of Ce³⁺ delivers Eu³⁺ luminescence at room temperature. This means that the Ce³⁺ ion can be used as a sensitizer in the TAG lattice that transfers its energy via the Tb sublattice to the activator Eu³⁺.     

惰性稀土离子和抗衡离子对2-噻吩乙醛酸-铕配合物荧光性能的影响

研究了惰性稀土离子和抗衡离子对一系列2-噻吩乙醛酸-铕配合物荧光性能的影响。分别在2-噻吩乙醛酸-邻菲罗啉-铕和2-噻吩乙醛酸-三苯基氧化膦-铕两个体系中按不同比例掺入钇和钆,研究了它们的荧光光谱。结果表明,钇的加入对2-噻吩乙醛酸-邻菲罗啉-铕体系的荧光强度有很强的敏化作用,并且随加入量的增加,这种敏化作用逐渐增强。钇的加入对2-噻吩乙醛酸-三苯基氧化膦-铕体系则呈现出弱的敏化作用,且在一定程度上具有猝灭作用,但这两种作用都是很微小的。钆在少量加入时对2-噻吩乙醛酸-三苯基氧化膦-铕体系具有猝灭作用,当大量加入时则呈现出很强的敏化作用。不同的抗衡离子对配合物的影响是明显的。在二元配合物中,氯化物体系的固体荧光强度最大;在三元配合物中,硝酸盐体系的固体荧光强度最大。     

蓝色长余辉材料CaAl_2O_4∶Eu~(2+),Li~+的发光性质

采用高温固相法制备了CaAl_2O_4∶Eu~(2+),Li~+发光材料,并讨论了掺杂Li+对CaAl_2O_4∶Eu~(2+)发光性质的影响。X射线衍射(XRD)和PL测试分析表明,在CaAl_2O_4∶Eu~(2+)中掺入Li~+后,Eu~(2+)的发光有一定的增强,而余辉时间则延长了4倍左右。通过热释光谱测量,分析了其陷阱能级的数量并估算了陷阱能级深度。结果表明,掺杂Li~+会在发光离子周围产生更多的电子陷阱,使陷阱的密度和深度增加,从而提高荧光粉的余辉性能。     

Tm3+掺杂SrAl2O4:Eu2+的光激励和热释光性能

通过高温固相法制备出Sr_{0.98-xAl2O4:0.02Eu²⁺,xTm³⁺(x=0,0.01,0.02,0.03,0.04,0.05)系列样品,并对其光激励和热释光性能进行了研究。在SrAl2O4:Eu²⁺原有陷阱能级结构的基础上,通过Tm³⁺的掺杂引入了更深的陷阱TB,并增加原有陷阱TA浓度,进而优化了材料的光存储容量及光激励特性。对比研究了系列样品的初始光激励发光强度和热释光强度随着Tm³⁺掺杂量的变化规律,证实陷阱TB为光激励发光提供了有效俘获中心。当Tm³⁺的掺杂摩尔分数x=0.03时,材料中的陷阱TB的浓度达到最高值,同时光激励发光强度最大。对比Tm³⁺共掺前后热释光图谱,通过Chen's半宽法计算出了引入陷阱TB的陷阱深度。实验结果证实材料中TB的浓度对其光激励发光性能起着决定性的作用。在980 nm激发下,由深陷阱TB释放出来的电子可以再次被浅陷阱TA俘获,这种浅陷阱TA的再俘获效应在光激励发光过程中表现为光激励余辉现象。}     

LiMAlF6(M=Ca,Sr)基质中Ce3+、Eu3+、Tb3+的光谱研究

合成了Ce³⁺、Eu³⁺、Tb³⁺激活的LiMAlF₆(M=Ca,Sr)磷光体,研究了它们的光谱特性.观察到稀土离子在LiCaAlF₆和LiSrAlF₆中的光谱十分相似.这与它们所处的晶场环境相同有关.发现Ce³⁺在此基质中有较弱的330nm发射,这一Ce³⁺的发光中心可用于作为材料质量的评价.     

Annihilation of the persistent luminescence of MAl2O4:Eu by Sm co-doping

The calcium aluminates doped with the Eu²⁺ and Nd³⁺ ions, CaAl₂O₄:Eu²⁺,Nd³⁺, are a novel and efficient persistent luminescence (i.e. afterglow) material. The Nd³⁺ ions were found to enhance the persistent luminescence. Some other R³⁺ co-dopants had similar or opposite, though weaker, effect. The Sm³⁺ (and Yb³⁺) ions suppressed almost completely the persistent luminescence and thermoluminescence of the Eu²⁺ ion. From the UV-excited luminescence and persistent luminescence spectra it was found that the Eu²⁺ ion acts as a luminescent centre with luminescence at the blue (λ_max=440 nm) region. The Sm³⁺ ion was reduced to the divalent state. The thermoluminescence glow curves of the CaAl₂O₄:Eu²⁺,Sm³⁺ material showed that the high-temperature glow peaks, i.e. deep traps, were suppressed almost completely. The Nd:YAG laser-excited high-resolution photoluminescence of the Sm²⁺ ion confirmed that the Eu²⁺ ion occupies only one Ca²⁺ site. Only weak perturbations were observed in the Sm²⁺ site due to the changes in the environment of the Sm²⁺ site.     

Ca3La(BO3)3：Tb3+的合成与发光性质

高温固相反应法合成了Ca₃La(BO₃)₃:Tb³⁺光致发光材料。利用扫描电镜和激光衍射分析仪测定了样品的晶粒形貌及粒径大小分布,利用荧光分光光度计研究了Ca₃La(BO₃)₃:Tb³⁺的光致发光特性。确定了在Ca₃La(BO₃)₃基质中Tb³⁺离子浓度对其发光强度的影响及其自身浓度猝灭机理;探讨了助熔剂Li₂CO₃、敏化剂Ce³⁺离子的加入对荧光粉发光强度的影响。     

荧光粉CaWO4：Eu3+中WO42-与Eu3+间的能量转递

通过高温固相法分别制备了CaWO₄和CaWO₄:1%Eu³⁺ 样品. 测量了样品不同温度(10–300 K)的荧光光谱、荧光衰减曲线和 时间分辨荧光光谱. 样品的荧光光谱表明: 在240 nm紫外光激发下, 两个样品在430 nm处都展现出来源于WO₄^2-的蓝色发射; 样品CaWO₄:Eu³⁺的Eu³⁺(⁵D₀→⁷F_{1, 2, 3,4})的特征发射则归属于WO₄^2-到Eu³⁺ 间的能量传递.由样品室温(300K)荧光衰减曲线发现: 纯CaWO₄的荧光寿命为8.85μs,Eu³⁺掺杂之后WO₄^2-的荧光寿命缩短至6.27μs,这从另一方面证明了WO₄^2-与Eu³⁺间能量传递的存在. 由荧光寿命得到T=300K时, CaWO₄: 1%Eu³⁺中WO₄^2-与Eu³⁺间的能量传递效率(η_ET)为29.2%, 能量传递速率(ω_ET)为4.65×10⁴ s^-1.通过时间分辨荧光光谱, 获得了从WO₄^2-到Eu³⁺之间的能量传递的时间演变过程,当温度由10 K增加到300 K时, 能量传递出现的时间单调变小. 测试了不同温度(10–300 K)对CaWO₄:Eu³⁺的荧光寿命的影响, 发现在10–50K时,Eu³⁺的荧光寿命增加, 但温度超过50K时发生猝灭, 荧光寿命开始下降; WO₄^2-的荧光寿命则是随着温度的升高逐渐缩短. 关键词： 能量传递 红色荧光粉 温度依赖 4：Eu³⁺')" href="#">CaWO₄：Eu³⁺     

大气环境下合成白光发射的Tb3+/Eu3+共掺杂全无机卤化物钙钛矿量子点

为克服因混合不同卤化物钙钛矿量子点发生阴离子交换反应、不稳定的红光发射卤化物钙钛矿量子点等而导致在获取白光发射方面存在的不足,提出了一种可以在大气环境下合成Tb³⁺,Eu³⁺稀土离子共掺杂全无机卤化物钙钛矿量子点的方法。调节Tb³⁺,Eu³⁺稀土离子的掺杂比例,调控从钙钛矿量子点主晶格到Tb³⁺和Eu³⁺离子的能量转移,获得了单一组分、白光发射的钙钛矿量子点(Tb,Eu):CsPbCl3和(Tb,Eu):CsPb(Cl/Br)3,并对量子点的形貌、结构、发光性能及能量传递机理和稳定性进行了详细研究。研究结果表明:在365nm激光激发下,不同含量Tb³⁺/Eu³⁺离子共掺杂的钙钛矿量子点(Tb,Eu):CsPbCl3发射光谱对应的色坐标位于1931色度图中的白光区域。在进料比PbCl2∶TbCl3∶EuCl3为1∶1.5∶1时,量子产率为3.59%,比纯的CsPbCl3量子点的量子产率(0.57%)提高了6倍。进一步研究发现,该(Tb,Eu):CsPbCl3量子点在空气中储存2个月之后,量子产率几乎保持不变(3.63%),保持了良好的稳定性。此外,研究了采用不同溶剂(正辛烷、十八烯)合成Tb³⁺/Eu³⁺共掺杂钙钛矿量子点的发光特性。Tb³⁺/Eu³⁺离子共掺杂的钙钛矿量子点(Tb,Eu):CsPbCl3可实现单一组分的白光发射,有良好的稳定性,具备一定的应用前景。     

Na+掺杂对LiYF4：Er3+/Yb3+上转换发光性能的影响

上转换发光材料由于低的发光效率,限制了其在太阳电池中的实际应用。为解决此问题,采用溶剂热法制备了LiYF₄：Er³⁺/Yb³⁺上转换发光颗粒,在LiYF₄基质中引入Na⁺来打破Er³⁺周围晶体场的对称性,增强其发光性能。研究了Na⁺掺杂对LiYF₄：Er³⁺/Yb³⁺的结构、形貌及其发光的影响。结果表明：掺杂的Na⁺可以裁剪Er³⁺周围的晶体场,当Na⁺摩尔分数为15%时,得到了较大的发光增强,绿光和红光发射分别获得4.2倍和2.9倍的增强。Er³⁺周围晶体场对称性的降低和材料中OH基团的减少是其发光增强的主要原因。