Optoelectronic and morphology properties of perovskite/silicon interface layer for tandem solar cell application

Silicon (Si) solar cell has low optical absorption because of the low and indirect bandgap of Si, and the efficiency was trapped at 25% for 15 years. Si solar cell is able to achieve efficiency up to 30% by adding perovskite as multiple bandgap material through tandem formation. In this paper, the Si/perovskite interface layer was characterized to study the compatibility of perovskite on fluorine-doped tin oxide (FTO) glass and p-type Si wafer (p-Si). The single solution deposition step of methyl ammonium lead iodide, CH₃NH₃PbI₃ (MAPbI₃) perovskite film, was spin-coated at different concentration. The physical properties of the MAPbI₃/FTO and MAPbI₃/p-Si were obtained by profilometer, atomic force microscope, X-ray diffraction, and Raman spectroscopy. The optical properties were analyzed by ultraviolet-visible spectroscopy, photoluminescence, and infrared transmission. Then the electrical properties were measured by Hall effect. From the measurement, it is observed that 1.2M concentration of MAPbI₃ thin film has the highest thickness, smoothest film surface, and largest crystallite size compared with 0.8M and 1.0M. It is found that there is an interaction in perovskite/Si interface and caused in a low-wavelength shift, and the increase in concentration of MAPbI₃ helped in intensifying the Raman signal produced. 1.2M MAPbI₃ thin film had the highest enhancement in light trapping property rather than 0.8M and 1.0M. The bulk concentration and conductivity of 1.2M perovskite were higher, but the resistivity was lower than 0.8M MAPbI₃ because of more CH₃NH₃I and PbI₂ concentration within MAPbI₃ perovskite compound.     

Post-treatment by an ionic tetrabutylammonium hexafluorophosphate for improved efficiency and stability of perovskite solar cells

Interface engineering is an effective way to improve efficiency and long-term stability of perovskite solar cells(PSCs).Herein,an ionic compound tetrabutylammonium hexafluorophosphate(TP6)is adopted to passivate surface defects of the perovskite film.It is found that TP6 effectively reduced the surface defects,especially at the grain boundaries where the defects are abundant.Meanwhile,the exposed long alkyl chains and fluorine atoms in the TP6 enhanced the moisture stability of the perovskite film due to its strong hydrophobicity.In addition,the driving force of charge carrier separation and transport is increased by enlarged built-in potential.Consequently,the power conversion efficiency(PCE)of PSCs is significantly improved from 20.59% to 22.41%by increased open-circuit voltage(V_oc)and fill factor(FF).The unencapsulated device with TP6 treatment exhibits better stability than the control device,and the PCE retains-80%of its initial PCE after 30 days under 15%-25%relative humidity in storage,while the PCE of the control device declines by more than 50%.     

Crystalline and active additive for optimization morphology and absorption of narrow bandgap polymer solar cells

The morphology of active layer with an interpenetrating network structure and appropriate phase separation is of great significance to improve the photovoltaic performance for polymer solar cells. A highly crystalline small molecule named DPP-TP6 was synthesized and incorporated into the narrow bandgap polymer solar cells to optimize the morphology of PTB7:PC₇₁BM active layer. The DPP-TP6 small molecule was demonstrated to enhance the light absorbance of active layer and play the role of energy cascade to increase the exciton separation and charge transfer. What's more, DPP-TP6 facilitated forming interpenetrating network structure and increasing the phase separation size of ternary blends. These phenomena lead to a higher hole mobility and a more balanced carrier mobility, so as to increase the power conversion efficiency to 7.85% at DPP-TP6 weight ratio of 8 wt %, comparing to the pristine PTB7:PC₇₁BM system of 6.50%. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 726–733     

Photophysics and morphology of a polyfluorene donor–acceptor triblock copolymer for solar cells

We present a study of the optical, structural and device properties of a polyfluorene (PFM)‐based (PFM‐F8BT‐PFM) donor–acceptor triblock copolymer for use in an organic solar cell. Neutron reflectivity is employed to probe the vertical composition profile before and after thermal annealing while the crystallinity was examined using grazing incidence wide‐angle X‐ray. The absorption spectra and photoluminescence emission for the triblock and analogous blend of PFM with F8BT reveal a greater degree of intermixing in the triblock. However, the triblock copolymer exhibits exciplex emission, which necessitates a geminate polar pair; long‐lived exciplex states are detrimental in organic photovoltaic devices. The triplet yield in the triblock and the blend is estimated using photoinduced absorption, with the triblock copolymer generating a triplet population 20 times that of the blend. This is far from ideal as triplets are wasted states in organic photovoltaic devices and they can also act as scavengers of polarons reducing the efficiency even more. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1705–1718     

Singlet relaxation dynamics and long triplet lifetimes of thiophene-coupled perylene diimides dyads: New insights for high efficiency organic solar cells

In the active layer of organic solar cells (OSCs), the lifetime of triplet excitons is one of the decisive factors in the diffusion length and therefore has important impact on the power conversion efficiency of the devices. Herein, we have investigated singlet excited state relaxation dynamics and their triplet exciton lifetimes of two thiophene-coupled perylene diimides (PDI) dyads (2PDI-Th and fused-2PDI-Th), in order to provide a unique explanation in depth on their different performances in OSC devices. From the transient absorption (TA) spectra, the singlet excitons of 2PDI-Th form excimers in the time scale of 1.5 ps. Then the excimers go into the triplet state via intersystem crossing (ISC). In fused-2PDI-Th, triplet excitons are generated directly from the singlet excited excitons via the efficient ISC. Density functional theory (DFT) calculations further support the formation of excimers. DFT results indicate that 2PDI-Th exhibits an H-typed molecular configuration which is beneficial to form the excimers, while fused-2PDI-Th gives a twisted X-shaped configuration in the optimized ground and excited state. In steady-state emission spectra, 2PDI-Th shows abroad and featureless spectral characteristics of the excimers with a decay time of 840 ps, which is much shorter than those of PDI (5.5 ns) and fused-2PDI-Th (3.3 ns). The triplet lifetime (67 μs) of fused-2PDI-Th is factor of 3 longer than that of 2PDI-Th (22 μs). These results demonstrate that ring-fused structure is an efficient strategy to eliminate excimer formation and prolong the lifetime of triplet excitons, which provides a new insight for design of optoelectronic molecules for high efficiency organic solar cells.     

Singlet relaxation dynamics and long triplet lifetimes of thiophene-coupled perylene diimides dyads: New insights for high efficiency organic solar cells

In the active layer of organic solar cells (OSCs), the lifetime of triplet excitons is one of the decisive factors in the diffusion length and therefore has important impact on the power conversion efficiency of the devices. Herein, we have investigated singlet excited state relaxation dynamics and their triplet exciton lifetimes of two thiophene-coupled perylene diimides (PDI) dyads (2PDI-Th and fused-2PDI-Th), in order to provide a unique explanation in depth on their different performances in OSC devices. From the transient absorption (TA) spectra, the singlet excitons of 2PDI-Th form excimers in the time scale of 1.5 ps. Then the excimers go into the triplet state via intersystem crossing (ISC). In fused-2PDI-Th, triplet excitons are generated directly from the singlet excited excitons via the efficient ISC. Density functional theory (DFT) calculations further support the formation of excimers. DFT results indicate that 2PDI-Th exhibits an H-typed molecular configuration which is beneficial to form the excimers, while fused-2PDI-Th gives a twisted X-shaped configuration in the optimized ground and excited state. In steady-state emission spectra, 2PDI-Th shows abroad and featureless spectral characteristics of the excimers with a decay time of 840 ps, which is much shorter than those of PDI (5.5 ns) and fused-2PDI-Th (3.3 ns). The triplet lifetime (67 μs) of fused-2PDI-Th is factor of 3 longer than that of 2PDI-Th (22 μs). These results demonstrate that ring-fused structure is an efficient strategy to eliminate excimer formation and prolong the lifetime of triplet excitons, which provides a new insight for design of optoelectronic molecules for high efficiency organic solar cells.