接枝共聚物EPR-g-PS作PS/EPDM共混体系增容剂的探讨

使用了由大分子单体共聚合制备的以乙丙橡胶(EPR)为主干、聚苯乙烯(PS)为支链的接枝共聚物EPR-g-PS作为PS/EPDM共混体系的增容剂。实验结果表明,共混体系的组成、增容剂加入量以及增容剂分子结构对共混体系冲击强度有很大影响。将这些因素与相差显微镜及扫描电镜研究所揭示的共混物形态的变化相联系,对此类接校共聚物作为不相容体系增容剂的机理作了探讨。     

Structure and properties of propylene-ethylene block copolymers and the corresponding blends

Structure and properties of presumed polypropylene(PP)-b-polyethylene(PE) block copolymers (PPPE) and the corresponding blends (PP/PE) have been investigated by wide-angle x-ray scattering (WAXS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), torsional pendulum apparatus, and other techniques measuring mechanical properties. Crystallinity, morphological structure, and mechanical properties of the block copolymers and blends vary with the PP and PE compositions. Compared with PP homopolymers and PP/PE blends, PP and PE segments in PP-PE block copolymers have a reduced crystallinity, especially PE segments. An additional peak at about ?40°C is observed in dynamic relaxation spectra; substantially different morphology is revealed; and mechanical properties are greatly improved for the sequentially copolymerized PP-PE block copolymers, indicating the existence of PP-PE block structure.     

Formation of superlattices via blending of block copolymers

Block copolymers are well‐known for their large number of microphase morphologies on mesoscopic length scales. After a short review of the different morphologies observed in binary block copolymers and ternary triblock copolymers, the self‐assembling in blends of different block copolymers into common superlattices is discussed in detail. Besides similar morphologies known for pure triblock and diblock copolymers, the blends can also show new morphologies. Examples of such new morphologies are periodic non‐centrosymmetric lamellae and multiple gyroid interface structures. The discussion of the superlattices is primarily based on investigations by transmission electron microscopy (TEM), which are supplemented in a few cases by small angle X‐ray scattering (SAXS) or results from computer simulations.     

Self-assembly behavior of ABA coil-rod-coil triblock copolymers: a Brownian dynamics simulation approach

The self-assembly behavior of ABA coil-rod-coil triblock copolymers in a selective solvent was studied by a Brownian molecular dynamics simulation method. It was found that the rod midblock plays an important role in the self-assembly of the copolymers. With a decrease in the segregation strength, ?(RR), of rod pairs, the aggregate structure first varies from a smecticlike disk shape to a long twisted string micelle and then to small aggregates. The influence of the block length and the asymmetry of the triblock copolymer on the phase behavior were studied and the corresponding phase diagrams were mapped. It was revealed that the variation of these parameters has a profound effect on microstructure. The simulation results are consistent with experimental results. Compared to rod-coil diblock copolymers, the coil-rod-coil triblock copolymers has a larger entropy penalty associated with the interfacial grafting density of the aggregate, leading to a higher ?(RR) value for structural transitions.     

A Novel Route to Graft-Copolymers with Tailored Structures for the Compatibilization of Polymeric Blend

A new method to synthesize graft-copolymers based on isotactic polypropylene (iPP) with tailored structure has been developed. The synthesis is a two-step process: synthesis of P-co-(p-MS-E) copolymers, by using ansa-metallocene catalysts, and metallation of p-Me groups followed by living anionic polymerisation for the graft growth. This method turn out to be versatile because, by changing experimental conditions, in the first step backbones with a tuned number of the graft growth sites and polypropylene lengths can be obtained, whereas in the second step, graft chains of different types and lengths can be synthesized. The particular ability of these copolymers to compatibilize polymeric blends was evaluated analyzing the morphology of the products copolymers/blends by using a scanning electron microscopy (SEM).     

PVC／PE交联共混体系的动态力学研究

在ＰＶＣ／ＰＥ共混体系中加入交联剂和引发剂能产生ＰＶＣ－ＣＯ－ＰＥ共聚物，这种共聚物在共混物中可起到增容剂的作用。通过动态力学分析和扫描电镜研究了ＰＶＣ／ＰＥ交联共混体系的相容性。发现引发剂、交联剂、稳定剂和增塑剂等对共混物中的交联反应均有较大的影响。     

On the macro- and microphase separation of compatibilizers in immiscible polymer blends

Macro- and microphase separation of compatibilizing graft copolymers in melt-mixed polystyrene/polyamide-6 blends was studied by transmission electron microscopy and thermal analysis. Three different graft copolymers with main chains of polystyrene and side chains of poly(ethylene oxide) were used as additives at various concentrations. The polyamide-6 domain sizes decreased with increasing amounts of compatibilizing graft copolymers in the blends up to a saturation concentration, after which no further reduction was noted. Macrophase separation of the graft copolymers into discrete macrodomains 20–200 nm in size occurred at concentrations equal to or slightly lower than the saturation concentration. The macrodomains of the graft copolymers were microphase separated, and the sizes and shapes of the microdomains were found to largely depend on the graft copolymer structure and composition. As a consequence of microphase separation, poly(ethylene oxide) crystallinity was noted in blends with sufficiently high macrophase contents. Observations of a graft copolymer interphase between the polystyrene matrix and the polyamide-6 domains confirmed that the graft copolymer was present at the blend interfaces in some of the compatibilized blends. © 1996 John Wiley & Sons, Inc.     

Synthesis of AB and ABA block copolymers as compatibilizers in nylon 6/polycarbonate blends

Nylon 6 (Ny6) and Bisphenol A polycarbonate (PC) are immiscible and form biphasic blends. To improve the compatibility of Ny6 and PC several ABA and AB Ny6/PC block copolymers were synthesized, and their compatibilizing behavior on the blends were tested. Block copolymers were prepared by reacting monoamino- or diamino-terminated Ny6 homopolymers with high molecular weight PC at 130°C in anhydrous DMSO. The reaction of diamino- and monoamino-terminated Ny6 with polycarbonate produces block copolymers of the type PC-Ny6-PC (ABA) and PC-Ny6 (AB), respectively, plus a certain amount of unconverted PC degradated to lower molecular weights. To separate the block copolymer from the unconverted PC, a selective fractionation with tetrahydrofuran (THF) and trifluoroethanol (TFE) was carried out. Three different fractions were obtained: THF-soluble fraction, TFE-soluble fraction, and the TFE-insoluble fraction. The scanning electron microscopy (SEM) analysis of a 75/25 (wt/wt) Ny6/PC blend added with 2% of ABA or AB block copolymers, showed the presence of smaller PC particles more adherent to the polyamide matrix, with respect to the same blend nonadded, which is clearly biphasic. The size of the PC particles decreases from ABA to AB compatibilized blends and the adhesion with the matrix is increases in the same way. © 1996 John Wiley & Sons, Inc.     

Compositionally symmetric diblock copolymer blends of moderate polydispersity

Recent experimental evidence and theoretical predictions indicate that binary blends of relatively monodisperse diblock copolymers remain miscible if the molecular weight disparity of the constituent copolymers is not too great. In this work, we examine the effect of moderate copolymer polydispersity on both the microstructural characteristics and phase behavior of blends prepared from four compositionally symmetric poly(styrene-b-isoprene) (SI) diblock copolymers ranging in polydispersity (M̄_w/M̄_n) from 1.02 to 1.30. Blend periodicities, measured by small-angle X-ray scattering, compare favorably with predictions from a strong segregation theory proposed for lamellar diblock copolymer blends composed of monomolecular copolymers. Transmission electron microscopy, employed to ascertain the real-space morphological characteristics of these blends, reveals that a lamellar → cylindrical transition occurs in macrophase-separated blends. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2653–2658, 1997     

Morphology and micromechanical behaviour of styrene/butadiene block copolymers and their blends with polystyrene

The correlation between the morphology and the deformation mechanism in styrene/butadiene block copolymers having modified architecture and in blends with homopolymer polystyrene (hPS) was studied. It was demonstrated that the morphology formation in the block copolymers is highly coupled with their molecular architecture. In particular, the micromechanical behaviour of a star block copolymer and its blends with polystyrene was investigated by using electron microscopy and tensile testing. A homogeneous plastic flow of polystyrene lamellae (thin layer yielding) was observed if the lamella thickness was in the range of 20 nm. The deformation micromechanism switched to the formation of craze-like deformation zones when the average PS lamella thickness changed to about 30 nm and more.     

Effect of selected structural parameters of styrene–butadiene block copolymers on their compatibilization efficiency in polystyrene/polybutadiene blends

The effects of the block length and block number of linear styrene–butadiene (S–B) block copolymers on their compatibilization efficiency in blending polystyrene with polybutadiene were studied. For this purpose, two sets of model S–B copolymers and both homopolymers were prepared by anionic polymerization. Diblocks, triblocks, or pentablocks of S–B copolymers were blended with these homopolymers, and the structures and some end‐use properties of the blends were determined. The supramolecular structure (determined by small‐angle X‐ray scattering), morphology (determined by transmission and scanning electron microscopy), and stress‐transfer characteristics (impact and tensile strengths) of the blends were chosen as criteria for the compatibilization efficiency of the copolymers used. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2612–2623, 2002     

Block copolymers as compatibilizers for blends of linear low density polyethylene and polystyrene

Compatibilization of blends of linear low-density polyethylene (LLDPE) and polystyrene (PS) with block copolymers of styrene (S) and butadiene (B) or hydrogenated butadiene (EB) has been studied. The morphology of the LLDPE/PS (50/50) composition typically with 5% copolymer was characterized primarily by scanning electron microscopy (SEM). The SEB and SEBS copolymers were effective in reducing the PS domain size, while the SB and SBS copolymers were less effective. The noncrystalline copolymers lowered the tensile modulus of the blend by as much as 50%. Modulus calculations based on a coreshell model, with the rubbery copolymer coating the PS particle, predicted that 50% of the rubbery SEBS copolymer was located at the interface compared to only 5–15% of the SB and SBS copolymers. The modulus of blends compatibilized with crystalline, nonrubbery SEB and SEBS copolymers approached Hashin's upper modulus bound. An interconnected interface model was proposed in which the blocks selectively penetrated the LLDPE and PS phases to provide good adhesion and improved stress and strain transfer between the phases. © 1995 John Wiley & Sons, Inc.     

Micellar aggregation in blends of linear and cyclic poly(styrene-b-isoprene) diblock copolymers

The morphology of micelles formed from blends of linear and cyclic poly(styrene-b-isoprene) (PS-b-PI) block copolymers has been investigated in solution using dynamic light scattering (DLS) and in thin solid deposits by atomic force microscopy (AFM) and transmission electron microscopy under cryogenic conditions (cryo-TEM). Micelles of the pure cyclic PS(290)-b-PI(110) copolymers are wormlike cylindrical objects built by unidirectional aggregation of 33 nm wide sunflower micelles, while the linear block copolymer having the same volume fraction and molar mass forms spherical micelles 40 nm in diameter. The DLS, AFM, and cryo-TEM results consistently show that the addition of the linear copolymer (even for amounts as low as 5% w/w) to the cyclic copolymer rather favors the formation of spherical micelles at the expense of the cylindrical aggregates. Those results clearly show that the linear block copolymer chains can be used to stabilize the thermodynamically unstable elementary sunflower micelle. The thermal stability of the micelles (from the pure copolymers and from the blends) has been examined in solid deposits with in situ AFM measurements. Coalescence starts at about 70 degrees C, and the surface roughness shows a two-step decrease toward a fully homogeneous and flat structure.     

Towards quantification of butadiene content in styrene-butadiene block copolymers and their blends with general purpose polystyrene (GPPS) and the relation between mechanical properties and NMR relaxation times

The properties of styrene-butadiene-styrene (SBS) block copolymers do not only depend on the butadiene content and the degree of polymerisation but also on their chain architecture. In this contribution we present the results of a low-field time domain (TD) NMR study in which the transverse relaxation behaviour of different SBS block copolymers was analysed and correlated with findings from mechanical testing on pure and blended materials and transmission electron microscopy data which provide information on the microphase separation.The results indicate that while a straightforward determination of the butadiene content as in blended materials like ABS is not possible for these materials, the TD-NMR results correlate quite well with the mechanical performance of blends from SBS block copolymers with general purpose polystyrene (GPPS), i.e. industrial grade homopolymer polystyrene. Temperature-dependent experiments on pure and blended materials revealed a slight reduction in the softening temperature of the GPPS fraction in the blends.     

Novel structural derivatives of poly-p-phenylenevinylene

Blends of oligoarylenevinylenes were prepared with polycarbonate, resp. polystyrene. These blends were investigated by electron microscopy as well as by differential scanning calorimetry (DSC) measurements. Block copolymers with well defined arylenevinylene segments were prepared by polycondensation of OH-functionalized oligoarylenevinylenes and aliphatic biscarboxylic acid chlorides. Arylenevinylene functionalized polystyrenes were prepared by Pd-catalyzed coupling reactions.     

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with poly(butadiene-block-methyl methacrylate)

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with butadiene-methyl methacrylate diblock copolymers has been investigated by transmission electron microscopy. When the diblock copolymers are added to the blends, the size of PB particles decreases and their size distribution gets narrower. In PB/PMMA7.6K blends with P(B-b-MMA)25.2K as a compatibilizer, most of micelles exist in the PMMA phase. However, using P(B-b-MMA)38K as a compatibilizer, the micellar aggregation exists in PB particles besides that existing in the PMMA phase. The core of a micelle in the PMMA phase is about 10 nm. In this article the influences of temperature and homo-PMMA molecular weight on compatibilization were also examined. At a high temperature PB particles in blends tend to agglomerate into bigger particles. When the molecular weight of PMMA is close to that of the corresponding block of the copolymer, the best compatibilization result would be achieved. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 85–93, 1998     

Study of self-assembly of symmetric coil-rod-coil ABA-type triblock copolymers by self-consistent field lattice method

The self-assembly of symmetric coil-rod-coil ABA-type triblock copolymer melts is studied by applying self-consistent field lattice techniques in a three-dimensional space. The self-assembled ordered structures differ significantly with the variation of the volume fraction of the rod component, which include lamellar, wave lamellar, gyroid, perforated lamellar, cylindrical, and spherical-like phases. To understand the physical essence of these phases and the regimes of occurrence, we construct the phase diagram, which matches qualitatively with the existing experimental results. Compared with the coil-rod AB diblock copolymer, our results revealed that the interfacial grafting density of the separating rod and coil segments shows important influence on the self-assembly behaviors of symmetric coil-rod-coil ABA triblock copolymer melts. We found that the order-disorder transition point changes from f(rod)=0.5 for AB diblock copolymers to f(rod)=0.6 for ABA triblock copolymers. Our results also show that the spherical-like and cylindrical phases occupy most of the region in the phase diagram, and the lamellar phase is found stable only at the high volume fraction of the rod.     

Organization of branched rod-coil molecules into a 3-D tetragonally perforated lamellar mesophase

Tetramerization of coil-rod-coil ABC triblock copolymers to a tetrabranched molecule induces an unusual 3-D tetragonally perforated layered liquid crystalline phase as an intermediate structure between 1-D lamellar and 2-D hexagonal columnar phases.     

The reactive compatibilization of NBR/EVA blends with oxazoline-modified nitrile rubber

The reactive compatibilization of ethylene-vinyl acetate copolymer (EVA)/nitrile rubber (NBR) blends has been performed using partially hydrolyzed EVA (EVALVA) in combination with oxazoline-functionalized NBR (NBROX). The synthesis of the NBROX has been performed in solution. The presence of 5 wt% of EVALVA in combination with 2.5 wt% of NBROX resulted in a substantial improvement of tensile strength of NBR/EVA (50:50 wt%) vulcanized blends, with a little increase of the elongation at break. The morphologies of these blends were examined by the scanning electron microscopy. A finer morphology has been observed in vulcanized and non-vulcanized blends, compatibilized with the co-reactive EVALVA/NBROX copolymers. Blends of NBROX/EVALVA (50:50 wt%) resulted in insoluble material, constituted by both components, as indicated by Fourier transform infrared analysis. This result indicates the reaction of the co-reactive groups (hydroxyl and oxazoline) during blending.     

顺1,4及反1,4聚丁二烯共混及共聚物结晶形态结构研究

本文用电镜、电子衍射及DSC等研究了顺1,4PB及反1,4PB的共混及共聚物的形态结构。观察了室温下两相结构分布随组分变化的规律及反1,4PB含量对顺1,4PB低温结晶、片层厚度和球晶大小的影响。进一步讨论了这两种不能形成类质同象结构物质结晶的相互影响。