随钻声波测井隔声体刻槽影响的数值模拟研究

针对随钻声波测井中钻铤波干扰以及刻槽后散射波问题,该文利用时域有限差分法模拟钻铤波在随钻隔声体中的传播规律,首先考察在无限大流体中钻铤波在凹槽分界面处的散射特征,利用波场快照直观显示了钻铤波会有一部分能量在刻槽的固液界面转化为斯通利波。同时在有地层时分别对比了均匀内刻槽和外刻槽对钻铤波的衰减效果,发现在选择均匀内刻槽还是外刻槽时结果不仅与频率范围有关,而且与刻槽的深度也有关系。最后对比了槽宽较大的均匀凹槽隔声体和槽宽较小的渐变凹槽隔声体。可以得出结论,在设计随钻隔声体时,在10 kHz以下选择均匀外刻槽方式相对于内刻槽隔声效果会更好。随着刻槽槽深增加,外刻槽在10 kHz以下相比于内刻槽隔声性能优势更加明显。渐变刻槽在满足衰减钻铤波幅度要求的同时,散射波对后续地层波和斯通利波影响也更小。     

周期性轴对称凹槽结构隔声特性数值模拟

提出一种在钻铤上切割周期性轴对称凹槽方式构建隔声体,消除钻铤模式波的方法.结果表明,其隔声效果与凹槽深度H、长度L、凹槽数目N、凹槽截面形状以及钻铤壁厚有关.选择矩形截面凹槽、减小钻铤壁厚、增加凹槽深度都可有效提高隔声体的隔声效果,该结构最高可获得约36 dB的声衰减,基本满足随钻声波测井仪器对隔声效果要求.     

软地层随钻测井仪器偏心情况下低频四极子源 激发波场的数值分析*

为了探索测井仪器偏心对随钻低频四极子波场的影响,利用有限元法(多物理场耦合有限元软件包)对软地层井孔中随钻仪器偏心情况下低频四极子声源激发的波场进行了数值模拟。通过对随钻四极子测井波形的分析可知,当采用低频随钻四极子偏心声源激发时,测井波列中除传播速度与低速地层横波速度相当的地层四极子波模式外,还存在一个幅度非常低、传播速度略高于井孔流体中声速的模式波,该模式被对应钻铤弯曲波模式,且该模式波的幅度随着随钻四极子源偏离井孔中心距离的增大呈二次方规律增大,地层四极子模式波幅度呈三次方规律增加。     

随钻新型隔声体的声学性能研究

随钻声波测井近年来逐渐发展为新兴的勘探方式,但钻探过程中产生的钻铤波会影响地层信号的提取,众多研究学者将如何更有效地提取地层信号作为了研究的重点课题.该文基于声子晶体理论设计了一种新型隔声体,相对于传统刻槽结构能够更好地压制钻铤波.首先基于周期结构理论,利用有限元软件计算了不同刻槽结构的能带图,相比于传统刻槽结构,新型...     

钻具遇卡声波检测理论与实验研究*

石油钻探过程中,钻具经常发生陷入泥沙中不能自由活动进而卡在井下的事故。本文提出使用单发双收声系来检测钻具遇卡的方法,首先使用有限差分模拟了钻具外为自由流体和泥沙两种介质时的钻铤波响应,通过对比远近接收器的钻铤波衰减,发现泥沙卡钻情况下的钻铤波衰减要明显大于自由钻具情况。随后建立了实验模型对理论结果进行了验证。理论模拟与实验结果均表明声波方法可用以检测钻具遇卡事故,从而确定卡钻的深度位置,为解卡钻作业提供解释依据。     

有效测量套管井泄漏Lamb波衰减的实验研究

低密度水泥在油气井中的广泛应用使得常规的声阻抗类测井方法难以准确、有效地评价固井质量,而声波倾斜入射在套管中激发的弯曲型Lamb波对水泥的性质及胶结情况具有很高的分辨能力,能够很好地解决低密度水泥的固井质量评价问题。弯曲型Lamb波对套管后介质声学信息的响应反映在声波衰减中,因此该文通过实验研究了激发弯曲型Lamb波的有效方式,分析了声波入射和接收角度对Lamb波衰减的影响。实验结果表明,入射和接收角度在一定范围内变化时,虽然激发出的Lamb波模式均为弯曲型Lamb波,但在同一套管模型下测量的声波衰减值会有差异,选择激发弯曲型Lamb波的最有效方式,计算得到的Lamb波衰减对套管后介质的灵敏度才会最高。     

弹性波数值模拟系统

弹性波数值模拟是石油测井仪器设计、研发和制造的有效工具,其有助于优化仪器的换能器频率、发射与接收器间的源距、接收器的个数及间距、隔声体的结构,也可帮助理解特定声源在复杂环境中的声传播规律及正确认识和评     

利用井中偶极弯曲波反演渗透率的影响因素及灵敏度分析

本文以各向同性饱和流体孔隙介质充液井孔中声场传播理论为基础,系统考察了影响偶极弯曲波特征的主要因素,分析了快慢地层条件下弯曲波衰减和速度对不同参数的敏感度,对比结果表明,弯曲波的速度基本不受地层渗透率的影响,其衰减对渗透率的敏感性要远高于速度。弯曲波中心频率会随着波的衰减而发生偏移,说明利用弯曲波衰减和频移特征联合反演地层渗透率是可行的。通过对比快慢地层下的弯曲波衰减和速度灵敏度曲线,发现在慢速地层中反演渗透率的结果要好于快速地层。同时,本文也指出在低孔低渗储层中,还可以考虑利用弯曲波衰减识别气层。     

套管中模式波的响应特征

在固井质量评价中主要利用套管中模式波的幅度或衰减变化反映水泥的胶结状况,不同测井仪器在套管中激发的模式波的类型不同,研究套管中各模式波的传播特征和影响因素可充分挖掘测量数据的潜在应用价值。CBL和SBT等测井仪器在套管中主要激发拉伸波,类同于平板中的零阶对称Lamb波,水泥环封隔测井仪器的斜入射模式在套管中主要激发套管弯曲波,类同于平板中的零阶反对称Lamb波,垂直入射模式激发套管共振波,类同于平板中的高阶对称Lamb波。该文重点分析了这些模式波的衰减特征及其对微环的响应,套管弯曲波在套后耦合轻质水泥时对微环不敏感,但在套后耦合常规水泥或重水泥时,其衰减明显高于胶结良好的状况;拉伸波对微环的存在最为敏感;套管共振波对微环不敏感。     

套管中泄漏弯曲型Lamb波的传播特征

低阻抗水泥固井质量检测是油气田生产亟需解决的问题。套管中传播的最低阶泄漏弯曲型Lamb波(以下简称为A0弯曲型Lamb波)对套管后介质尤其是低阻抗水泥的声学参数和胶结状况具有很高的敏感性。通过建立多层介质模型,从理论上计算了其频散和衰减与套管后介质属性及水泥环第Ⅰ界面胶结状况的关系,并数值模拟了有限尺寸定向辐射探头激发和接收的全波波形。结果表明,在套管后耦合慢速水泥时,A0弯曲型Lamb波的频散曲线存在断点,曲线分为两个分支;A0弯曲型Lamb波的衰减在套管后耦合慢速水泥时最大并且对水泥环第Ⅰ界面胶结差时流体环厚度有很高的灵敏度,利用其衰减可以实现对套管后介质类型、水泥环第Ⅰ界面胶结状况及窜槽厚度的有效判别。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.