Determination of polymer additives using analytical pyrolysis

When analyzing a polymeric material using pyrolysis-GC, the majority of the peaks seen are degradation products from the polymer matrix, but there may be specific compounds present resulting from the presence of antioxidants, plasticisers, stabilizers, flame retardants and other additives. Some of these compounds may be volatile or semi-volatile and appear as intact molecules, while others are larger and only appear as fragments after the pyrolysis. In understanding the pyrolysis of the complete system, it is important to understand the behavior of such additives under the thermal conditions used to analyze the polymer matrix.This paper presents data for several polymer additives, showing their contribution to the analytical results when studying typical polymers using Py-GC/MS. Specific types of additives include phenolic antioxidants, hindered amine light stabilizers, phthalates and phosphites.It was determined that for some additives, especially when analyzing simple polymers, co-analysis of the polymer and additive was feasible. For other, more complex formulas, a multi-step approach permitted a thermal separation of compound families and simplified the analysis. For some additives, especially in the parts-per-million range, pyrolysis with selected or extracted ion mass spectrometry was the most informative.     

The analysis of heterogenous polymer systems using solid-state NMR techniques

Two different types of high resolution solid-state ¹³C-¹H cross depolarization experiments were applied to a rubber toughened thermoset polymer. A polypropylene blend was examined using a solid-echo ¹H wide line pulse sequence over the temperature range from 27 to 197°C. The frequency domain spectra were curve fitted to obtain the relative abundances of the three distinct ¹H T₂ components as a function of temperature.     

Optical emission laser microprobe analysis of synthetic oxide monocrystals

The existing methods of laser microprobe spectrochemical analysis are reviewed. Some atomic emission spectroscopic (AES) methods analysis for synthetic high-melting oxide monocrystals applying solid lasers have been studied by the authors. A two-stage method of analysis of monocrystals including preliminary laser sampling with condensation of the ejected substance on the plane surface of a graphite rod and subsequent AES analysis of the condensate in an independent excitation source was developed and used. The method proved to be more efficient than other laser analysis methods studied. The regularities of laser ejection of Ca₂V₂O₇ monocrystal substance, the composition and distribution of its condensate on the surface of a substrate serving as a collector of the condensate were investigated in model experiments. The identity of the elemental compositions of condensate and the monocrystal analysed was shown. Dry residues of standard aqueous solutions served as reference samples. A unipolar impulse discharge and an a.c. arc were used as the excitation sources for the condensate spectrum; the a.c. arc turned out to be more suitable. The correctness of the quantitative determination of the impurities doped in Ca₂V₂O₇ monocrystals when applying the two-stage laser microprobe analysis was proved by the direct AES method of analysis of the same monocrystals which had been completely dissolved. Examples of practical application of the two-stage laser analysis method for the investigation of calcium vanadate monocrystals and also examples of the direct d.c. arc AES analysis method for the investigation of synthetic monocrystals of titanium dioxide are given.     

Applications of laser microprobe mass spectrometry in organic analysis

The ability to focus the laser accurately onto the sample with a small beam diameter (2.0–3.0 μm) enables laser mass spectrometry to be used as a microprobe. Results from a fully automated ion-mapping system for laser mass spectrometry are described. These results show that the spatial resolution of the laser microprobe is primarily limited by the diameter of the laser beam. Factors such as laser power density, laser focus, sample preparation, and chemical environment influence the reproducibility of laser mass spectra significantly. Calibration curves obtained in the analysis of mixtures of phenanthrolines demonstrate that laser mass spectrometry can be used to quantify organic components. Preliminary results on the detection of neutral molecules resulting from metastable decomposition in the flight tube are also presented.     

Characterization of airborne particulates by laser microprobe mass analysis

Summary Laser microprobe mass analysis (LAMMA) was applied to characterize aerosol particles collected and separated from 16m to 0.06m by a low pressure cascade impactor. Positive ion LAMMA spectra showed characteristic molecular peaks such as PbCl⁺, a series of Si₂O⁺–Si₂O₄ ⁺ and NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, and TiO⁺ in 0.06–0.12m, 0.5–1m and 4–8m fraction, respectively. In the negative ion LAMMA spectra, it was observed that the fragment peaks of sulfate ions were deficient above 2m and those of nitrate ions were deficient under 2m. LAMMA allows remarkable insights into the chemical nature of aerosol particles.

---

Charakterisierung luftgetragener Teilchen durch Laser-Microprobe-Massenspektrometrie

Zusammenfassung Laser-Microprobe-Spektrometrie (LAMMS) wurde zur Analyse atmosphärischen Aerosols herangezogen, welches im Korngrößenbereich zwischen 16m und 0.06m mit einem Niederdruckkaskadenimpaktor fraktioniert gesammelt wurde. Positive LAMMS-Spektren zeigten charakteristische molekulare Peaks, wie etwa PbCl⁺, eine Serie von Si₂O⁺–Si₂O₄ ⁺ und NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, sowie TiO⁺ in der 0,06–0,12-m,- 0,5–1–m- bzw. 4–8-m-Fraktion. In den negativen LAMMS-Spektren konnten über 2m keine Fragmentpeaks für Sulfationen, unter 2m. keine für Nitrationen beobachtet werden. LAMMS ermöglicht eine bemerkenswerte Einsicht in die chemische Natur von Aerosolteilchen.

     

Laser microprobe mass spectrometry of quaternary phosphonium salts: Direct versus matrix-assisted laser desorption

The use of laser microprobe mass spectrometry (LMMS) for the structural characterization of thermolabile quaternary phosphonium salts has been evaluated. A comparison has been made between LM mass spectra obtained by direct analysis of “neat” organic salts and the corresponding “matrix-assisted” LM mass spectra. Main limitations of LMMS for the direct analysis of neat organic salts (i.e., no matrix) result from (1) formation of artifact ions that originate from thermal degradation and surface recombination reactions and (2) poor shot-to-shot reproducibility of the spectra. Dilution of the organic salts in a suitable, UV-absorbing matrix (e.g., nicotinic acid) significantly enhances the quality of the LM mass spectra. Improvements are: (1) an increase of the ion yield of preformed cations, (2) reduction or elimination of thermal decomposition and other deleterious surface reactions, and (3) a much better shot-to-shot spectral reproducibility. An interesting analytical feature is that these LM mass spectra, which contain only a few matrix peaks, can be obtained for subnanogram amounts of sample. The results also show that triphenylphosphonium salts with polycyclic aromatic substituents can be used as “molecular thermometers” to probe both the temperatures experienced by the sample molecules during the laser-induced desorption ionization process and the internal energies of the desorbed ion species. In this way, quaternary phosphonium salts can be used for evaluating whether improvements have been achieved by applying different sample treatments. Comparison of four different matrices (i.e., nicotinic acid, ammonium chloride, glycerol, and 3-nitrobenzylalcohol) indicates that the effectiveness of a matrix to reduce thermal degradation and to decrease the internal energies of the ions depends on the UV-absorption characteristics and the volatilization/sublimation temperature of the matrix material.     

Direct quantitative analysis of peptides using matrix assisted laser desorption ionization

The protocol and various matrices were examined for quantification of biomolecules in both the low ca. 1200 amu and mid mass 6000-12000 amu ranges using an internal standard. Comparative studies of different matrices of MALDI quantitative analysis showed that the best accuracy and standard curve linearity were obtained for two matrices: (a) 2,5-dihydroxybenzoic acid (DHB) combined with a comatrix of fucose and 5-methoxysalicylic acid (MSA) and (b) ferulic acid/fucose. In the low mass range, the quantitative limit was in the 30 fmol range and in the mid mass range the quantitative limit was in the 250 fmol range. Linear response was observed over 2-3 decades of analyte concentration. The relative error of the standard curve slope was 1.3-1.8% with correlation coefficients of 0.996-0.998.The main problem for quantitative measurement was suppression of the signal of the less concentrated component (analyte or internal standard) by the more concentrated component. The effect was identified with saturation of the matrix by the analyte. The threshold of matrix saturation was found to be in the range of 1/(3000-5000) analyte/matrix molar ratio. To avoid matrix saturation the (analyte+internal standard) to matrix molar ratio should be below this threshold. Thus the internal standard concentration should be as low as possible.DHB/MSA/fucose and ferulic acid/fucose matrices demonstrated good accuracy and linearity for standard curves even when the internal standard had chemical properties different from the analyte. However, use of an internal standard with different chemical properties requires highly stable instrumental parameters as well as constant (analyte+internal standard)/matrix molar ratio for all samples.     

Direct quantitative analysis of peptides using matrix assisted laser desorption ionization

The protocol and various matrices were examined for quantification of biomolecules in both the low ca. 1200 amu and mid mass 6000–12000 amu ranges using an internal standard. Comparative studies of different matrices of MALDI quantitative analysis showed that the best accuracy and standard curve linearity were obtained for two matrices: (a) 2,5-dihydroxybenzoic acid (DHB) combined with a comatrix of fucose and 5-methoxysalicylic acid (MSA) and (b) ferulic acid/fucose. In the low mass range, the quantitative limit was in the 30 fmol range and in the mid mass range the quantitative limit was in the 250 fmol range. Linear response was observed over 2–3 decades of analyte concentration. The relative error of the standard curve slope was 1.3–1.8% with correlation coefficients of 0.996–0.998.The main problem for quantitative measurement was suppression of the signal of the less concentrated component (analyte or internal standard) by the more concentrated component. The effect was identified with saturation of the matrix by the analyte. The threshold of matrix saturation was found to be in the range of 1/(3000–5000) analyte/matrix molar ratio. To avoid matrix saturation the (analyte+internal standard) to matrix molar ratio should be below this threshold. Thus the internal standard concentration should be as low as possible.DHB/MSA/fucose and ferulic acid/fucose matrices demonstrated good accuracy and linearity for standard curves even when the internal standard had chemical properties different from the analyte. However, use of an internal standard with different chemical properties requires highly stable instrumental parameters as well as constant (analyte+internal standard)/matrix molar ratio for all samples.     

Application of the N2 laser to laser microprobe spectrochemical analysis

Results are presented of a study on the application of a N₂ laser to the spectrochemical analysis of microareas. It is found that when the pressure of the surrounding gas is reduced to 1 Torr (133 Pa) or thereabouts, the plasma induced by the bombardment of N₂ laser light yields sharp atomic line spectra with a negligibly low background signal, facilitating quantitative analysis with reasonable precision. A simple and rapid detection method is employed in which the atomic emission spectrum from the plasma produced under successive bombardment (10 Hz) is recorded directly on a chart by means of scanning the wavelength of a monochromator. By using iron-steel standard samples of known content, it is demonstrated that a plot of the intensity of the 425.4 nm emission line of Cr against the Cr content shows a linear relationship.     

High-temperature elemental analysis and pyrolysis techniques for stable isotope analysis

A universal method for pyrolysis and elemental analysis, suitable for the online determination of deuterium, carbon, nitrogen and oxygen isotopes for organic and inorganic substances, is presented. The samples are pyrolytically decomposed in a high-temperature pyrolysis (HTP) system, at a temperature exceeding 1400 degrees C, in the presence of reactive carbon. The method is suitable for the analysis of stable isotope ratios from hydrogen, carbon, nitrogen and oxygen. The instrumentation and experimental procedure are simple and cost-effective. The reproducibility of the delta values for D/H is better than 3 per thousand, and for (18)O, (13)C (organic) and (15)N (inorganic) it is approximately 0.2 per thousand. The HTP system is suitable for solid and liquid samples and can use an autosampler for the samples. Results are presented for the isotopic composition of international reference materials and selected laboratory reference materials, which demonstrate the precision and accuracy of the method. Possible problems in the measurement of nitrates and their solutions are particularly discussed. The analyses of oxygen isotopes in selected geological samples (carbonates, silicate, biotite) are demonstrated.     

Analytical techniques with a nuclear microprobe

Nuclear microprobes have proved to be versatile tools to perform investigations in materials science with a lateral resolution of typically 1 to 10 m. Many of the commonly utilized ion beam assisted analytical techniques, like PIXE (Particle Induced X-Ray Emission), RBS (Rutherford Back Scattering), NRA (Nuclear Reaction Analysis), and Channeling can be applied with a nuclear microprobe. Additionally, there are methods typical for the nuclear microprobe, e.g. STIM (Scanning Transmission Ion Microscopy). The nuclear microprobe used here has been applied successfully to the analysis of geological and biological specimens and is currently being modified by the introduction of a superconducting solenoid as focusing element to allow higher lateral resolution. Especially the analysis and modification of electronic devices will become possible. An overview of the analytical techniques practiced with the nuclear microprobe is given with emphasis on laterally resolved trace element analysis.     

Concentration distribution of elements in heterogeneous polymer systems determined by electron microprobe analysis

A technique for analysis of composition variations in heterogeneous polymer systems permits investigation of materials with both uniform and nonuniform distribution of heterostructural components. To illustrate the method, determinations have been made of concentration profiles of dibromo-diallyl-phthalate formed in porous PVC in two different ways.     

Molecular speciation of microparticles: application of pattern recognition techniques to laser microprobe mass spectrometric data

Attempts were made to enhance the ability of laser microprobe mass spectrometry (LAMMS) to identify molecular species in individual microparticles by applying pattern recognition methods. Principal component analysis (PCA) and canonical discriminant analysis were applied to LAMMS data for nickel-containing environmental particles. Detailed comparison of the two statistical methods demonstrated the utility of PCA. The successful application was highly dependent on the use of appropriate spectral normalization and feature extraction techniques prior to PCA. Although the test system involved only a small number of standard compounds, the LAMMS data were complicated by the effects of intra-particle heterogeneity common to environmental samples and by instrumental limitations. Pattern recognition techniques provided more accurate quantitative assignments of molecular species than were available by qualitative inspection of characteristic cluster ions or by simple spectral subtraction to compare particle data with a library of standard compounds. Results were substantiated by comparison with bulk analysis studies using wet chemical techniques.     

Nuclear methods of analysis applied to quantitation in laser microprobe mass spectrometry

Laser microprobe mass spectrometry (LMMS) detection limits for mercury have been determined using mercury-doped Spurr's tissue embedding medium. Actual mercury concentrations were confirmed via INAA. Procedures have also been developed to measure lithium and indium concentrations in thin films of polymerized Spurr's samples via PIGE and PIXE. These elements are currently being investigated as laser power density internal standards in the analysis of human tissue for studies of trace element involvement in neurological diseases.     

Laser ablation and the laser microprobe

The development of laser optical sources has made possible a variety of powerful, new analytical techniques. One such technique, the laser microprobe, is used for the microanalysis of a large variety of samples ranging from single crystals and aerosols, to refractory minerals.     

Pulsed laser powered homogeneous pyrolysis: A computational analysis

The use of the pulsed laser powered homogeneous pyrolysis technique for measuring unimolecular decomposition rate constants under unambiguously homogeneous conditions is investigated by numerical simulation of the experiment. The coupled partial differential equations which govern the gas dynamics and chemical kinetics are solved numerically and the results analyzed. Conditions under which rate constants can be extracted from the experimental data using a simplified analysis are determined. The effects of five sources of error in the simplified analysis are computed. A correlation is presented which may be used to correct for overestimation of the rate constant which is inherent in the simple analysis. Conditions under which the other four sources of error become negligible are presented. Overall, it is expected that this technique will be capable of routinely measuring rate constants within a factor of 2, and will do much better when a high power laser with a uniform beam profile is used and/or a well characterized thermal monitor molecule is available which decomposes with kinetic parameters close to that of the reactant being investigated. © 1994 John Wiley & Sons, Inc.     

Multielement analysis of coal by ICP techniques using solution nebulization and laser ablation

The combination of inductively coupled plasma atomic emission spectrometry and high resolution inductively coupled plasma mass spectrometry for the determination of 70 elements in coal were studied. Four microwave-assisted digestion procedures with different dissolution mixtures (nitric and hydrofluoric acids, aqua regia and hydrogen peroxide), lithium metaborate fusion with and without previous sample ashing as well as direct sampling by laser ablation (LA) have been tested. Examples of spectral interferences are given and different correction procedures are discussed. Detection limits in the low ng g(-1) range were obtained for most of the elements investigated by using high-purity reagents and by taking special care to prevent sample contamination during preparation. The precision was assessed from replicate analysis (including sample preparation) of coal samples and was found to be, as average values far all elements, 4-5% RSD and 10-15% RSD for procedures including sample digestion and LA sampling, respectively. The accuracy of the overall analytical procedures was estimated by analysis of certified reference materials and of a coal sample obtained from the Interlab Trace round robin test. Among the dissolution mixtures tested, the combination of nitric and hydrofluoric acids with hydrogen peroxide provide the best agreement with certified, recommended, literature-compiled or consensus values, though fusion is necessary to obtain quantitative recoveries for Si, Cr, Hf, W, Zr, Y. In general, results obtained by LA fall within +/-20% of those obtained after digestion.     

PIXE macro and microprobe techniques in archaeometry

PIXE analysis method is applied to archaeometry problems. Advantages and disadvantages are emphasized. Some examples are presented which show the difficulties; especially important heterogeneities of ceramics, old coins and metals restrain from the use of this technique: other analysis systems, less expensive, like electron microprobe or X-ray fluorescence spectrometry, are compared with conventional PIXE method. The importance of proton microprobe is explained.     

An investigation of laser microprobe mass spectrometry (LAMMS) for polymer surface treatment and its inhomogeneity

Laser microprobe mass spectrometry was applied for the detection of inhomogeneity of the polycarbonate surface treated with silane coupling agent. Clear difference in spectrum patterns between the treatments with and without a non-ionic fluorocarbon surfactant was observed. The chemical bonds between silicon/zirconium and carbon have been confirmed to generate only in the presence of the surfactant which participates in homogenization of the surface.