可膨胀石墨催化合成乙酸苄酯

可膨胀石墨作为一种重要的非金属材料已广泛应用于各工业领域 ,将其作为有机质反应催化剂的研究尚不多见[1～ 3] 。工业上 ,乙酸苄酯常是以浓Ｈ2 ＳＯ4、对甲苯磺酸等质子酸作催化剂由乙酸和苄醇制得[4] ,但此法腐蚀设备 ,污染环境 ,且副反应多。近年来 ,为了寻找对设备腐蚀性小的酯化反应催化剂进行了一些研究 ,如曾报道的酯化反应催化剂有 :四氯化锡复合物[5] 、复合固体超强酸[6] 、稀土硫酸盐[7]等。本文报道可膨胀石墨催化乙酸苄酯的合成 ,与其它催化剂相比 ,具有催化活性高 ,反应温度低 ,反应时间短 ,收率高 ,易分离及再生处理简单等…     

石墨与聚苯乙烯的纳米复合过程研究

石墨具有电导率高、化学稳定性好等优点 ,被广泛应用于聚合物 石墨复合导电材料[1～ 3] .石墨作为聚合物导电填料一般以粉末形态居多 .用粉末状石墨填料往往需要较高的填充量才能得到理想的导电性能 .石墨也可以制备成膨胀石墨 ,将它与聚合物复合 ,可以大幅度降低石墨的填充量 .如一般粉末状石墨填料与聚合物复合制备的导电材料其逾渗阀值为 1 5 %～ 2 0 % ,电导率达到 1 0 -4 ～1 0 -7Ｓ ｃｍ[4 ] ;而若采用膨胀石墨方法 ,逾渗阀值则低于 3% ,电导率可达到 1 0 -2 Ｓ ｃｍ以上[5～ 7] .Ｐａｎ等[7] 报道用膨胀石墨与聚合物复合得到纳米复合…     

H2SO4/HNO3混酸和高铁酸钾体系制备膨胀石墨

以天然鳞片石墨为原料、高铁酸钾为氧化剂、浓硫酸、硝酸为插层剂微波法制备膨胀石墨,通过红外光谱、XRD和SEM对其结构进行表征。探讨了混酸用量、氧化剂用量、混酸比例、插层反应温度、插层反应时间对膨胀效果的影响。结果表明,石墨（g）:高铁酸钾（g）:混酸（mL）为1:0.3:18、V硫酸:V硝酸为2:1、插层反应温度35 ℃、反应时间60 min时,膨胀体积达75 mL/g,比硫酸为插层剂时膨胀体积增长了约87.5%。     

可膨胀石墨的制备

本文研究了一种以天然石墨和混酸为原料，高锰酸钾为氧化剂制备高膨胀容积可膨胀石墨的新方法。其最佳参数为：混酸与石墨的重量比为3∶1；高锰酸钾为石墨重量的8%；反应温度25℃；反应时间0.5 h。制得的可膨胀石墨每克可膨胀体积为375毫升，比传统方法制得的可膨胀石墨高出175 ml/g。     

己二酸绿色合成新途径

己二酸是合成纤维的重要原料 .己二酸的工业生产过程大都采用环己酮和环己醇的硝酸氧化法 ,因而造成了严重的环境问题 .尽管可对Ｎ2 Ｏ进行有效的回收和利用[1],但其年排放量仍达到 4 0万吨[2 ].因此 ,增加化学反应过程的选择性 ,最大限度利用初始原料 ,用催化剂代替传统工业上使用的有毒或有腐蚀性的化学计量反应试剂以及使最终反应产物更加容易分离是绿色合成技术的主要目标[3].烃类选择性氧化的传统氧化剂为Ｋ2 Ｃｒ2 Ｏ7,ＫＭｎＯ4,ＨＮＯ3,ＮａＯＣｌ等 ,该类氧化剂已逐步被清洁氧化剂所取代[4 9].Ｎｏｙｏｒｉ等[10 ]以Ｎａ2 ＷＯ4·2…     

三元脂肪酸/膨胀石墨复合相变材料的制备、包覆定形及热性能

采用癸酸、 月桂酸和棕榈酸的三元共晶混合物作为相变材料, 以膨胀石墨为基体, 通过膨胀石墨多孔结构的毛细吸附和复合涂饰剂的包覆定形, 将多元相变材料固定在膨胀石墨的孔道结构中, 制备出结构稳定、 密封性能优异、 热稳定性好和高导热的新型三元脂肪酸/膨胀石墨复合定形相变材料. 膨胀石墨具有膨胀疏松的多孔结构和良好的吸附性能; 其熔融潜热为95.6 J/g, 结晶焓为82.8 J/g, 说明其具有很好的相变蓄热特性和热循环稳定性; 材料的导热性能可增加至0.738 W/(m·K), 与脂肪酸相比得到大幅度提高.     

锂硫电池硫膨胀石墨正极材料的电化学性能

应用高温气相扩散沉积法由单质硫制备硫膨胀石墨.该硫膨胀石墨正极可降低反应界面电荷传递阻抗,提高扩散阻抗抑制单质硫或多硫化物在充放电过程的穿梭.其首次放电容量达到972 mAh.g-1,容量保持率为78%,循环效率在80%以上.     

氧化程度对微细鳞片可膨胀石墨结构及膨胀性的影响

以平均粒径为19.71μm的天然微细鳞片石墨为原料,通过化学氧化法制备了具有不同氧化程度的可膨胀石墨,采用XRD、FTIR、Raman、SEM等对可膨胀石墨的结构与膨胀性进行了表征。结果表明：当氧化程度较低时制得的微细鳞片可膨胀石墨由石墨、石墨层间化合物和氧化石墨三相组成;随着氧化程度的增加,氧化石墨相含量与可膨胀石墨结构无序程度逐渐增高,石墨层间化合物相含量先增加后减少,石墨相含量则逐渐降低;氧化促使HSO₄^-或SO₄^2-插入石墨层间,插入层间的HSO₄^-或SO₄^2-量是决定可膨胀石墨膨胀容积的关键因素,制备的微细鳞片膨胀石墨的膨胀容积可达65.9mL·g^-1。     

氧化程度对微细鳞片可膨胀石墨结构及膨胀性的影响

以平均粒径为19.71μm的天然微细鳞片石墨为原料,通过化学氧化法制备了具有不同氧化程度的可膨胀石墨,采用XRD、FTIR、Raman、SEM等对可膨胀石墨的结构与膨胀性进行了表征。结果表明:当氧化程度较低时制得的微细鳞片可膨胀石墨由石墨、石墨层间化合物和氧化石墨三相组成;随着氧化程度的增加,氧化石墨相含量与可膨胀石墨结构无序程度逐渐增高,石墨层间化合物相含量先增加后减少,石墨相含量则逐渐降低;氧化促使HSO4-或SO42-插入石墨层间,插入层间的HSO4-或SO42-量是决定可膨胀石墨膨胀容积的关键因素,制备的微细鳞片膨胀石墨的膨胀容积可达65.9mL·g-1。     

硫酸氢钠催化合成丁酸异戊酯

丁酸异戊酯有类似梨的水果香气 ,广泛应用于溶剂、日用香精和食用香精中[1,2 ] .目前 ,工业上主要采用硫酸催化丁酸和异戊醇酯化法来合成[3] ,为克服硫酸催化法的缺点 ,改善合成环境 ,人们曾研究过采用结晶氯化铁、超强酸及杂多酸等催化合成丁酸异戊酯[4～ 6] ,然而结晶氯化铁很易吸潮、难于保管和准确使用 ,超强酸和杂多酸需要制备 ,成本较高 .本文选用的硫酸氢钠 (ＮａＨＳＯ4 ·Ｈ2 Ｏ)是一种价廉易得的无机酸性晶体 ,易保管且使用方便 ,催化效果好 ,同时它又不溶于有机反应体系 ,具有一定的重复使用性能 ,至今未见用ＮａＨＳＯ4 ·Ｈ2 …     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.