An ionic liquid-type multiwall carbon nanotubes paste electrode for electrochemical investigation and determination of morphine

The direct electrochemistry of morphine on modified multiwall carbon nanotubes using carbon ionic liquid (i.e., 1-butyl-3-methylimidazolium hexafluoro phosphate, ([C4mim]–[PF6])) was studied. It was found that the electrode showed sensitive voltammetric response to morphine. The experimental results suggested that the modified electrode promoted electron transfer reaction for the oxidation of morphine. The electron transfer coefficient and charge transfer resistant (R _ct) of morphine at the modified electrode were calculated. Under the optimized conditions at pH 8.0, the peak current was linear to morphine concentrations over the concentration range of 0.45–450 μmol L⁻¹, using differential pulse voltammetry. The detection limit was 0.14 μmol L⁻¹. The proposed method was successfully applied to the determination of morphine in both ampoules and urine samples.     

Online Monitoring of Bromate in Ozonized Water Without a Previous Separation Process

The use of ozonation for the purification of drinking water can lead to the formation of bromate. The US Environmental Protection Agency and the European Directive for human drinking water has lowered the regulatory level for bromate down to 10 μg l⁻¹, such that methods must be developed for monitoring the formation of bromate, particularly in on-site situations. In the present work we report a fluorometric method for the determination of bromate based on the reaction with carbostyril-124, a compound that shows florescence mainly at pH values above 4 and, when bromated, generates a non-fluorescent product. The reaction can thus be used as an indirect method for determination of the ion. The proposed method, which uses the flow injection (FI) technique, allows online application and kinetic control of the variables affecting the process, together with shorter reaction times, and it provides maximum sensitivity and selectivity. Under optimum conditions, it is possible to determine the analyte within the 4–200 μg l⁻¹ range, with a limit of detection of 0.9 μg l⁻¹ and a relative standard deviation (n = 12, [] = 5 and 30 μg l⁻¹) of 3.2% and 2.6% respectively. The determination rate was ten samples per hour.     

The influence of hydrogen plasma pre-treatment on the structure of BDND electrode surface applied for phenol detection

The surface properties of boron-doped nanocrystalline diamond films treated with H₂ plasma was investigated in regard to their electrochemical response for phenol oxidation. The surface of these films is relatively flat formed by crystallites with sizes of about 40 nm. X-ray photoelectron spectroscopy analyses showed that electrode surface has a high amount of C–H bonds. This behavior is in agreement with Mott-Schottky plot measurements concerning the flat band potential that presented a value as expected for hydrogenated diamond surface. This electrode presented the phenol detection limit of 0.08 mg L⁻¹ for low phenol concentrations from 40 to 250 μmol L⁻¹.     

Tunable diode laser spectroscopy of benzene near 1684 nm with a low-temperature VCSEL

We describe the application of a long-wavelength vertical-cavity surface-emitting laser (VCSEL) with extended tuning range to the detection of benzene vapor at atmospheric pressure. A benzene absorption feature centered at 1684.24 nm was accessed by reducing the heat sink temperature of a VCSEL designed for room-temperature operation to −55°C. This allowed us to increase the injection current and thus to extend a single-scan tuning interval up to 46.4 cm⁻¹ or 13.2 nm around a central wavelength of 1687.4 nm. Five absorption lines of methane in the 5903–5950 cm⁻¹ range could be acquired within single laser scans at a repetition rate of 500 Hz. A benzene absorption feature between 5926 and 5948 cm⁻¹ was recorded for concentration measurements at atmospheric pressure using a single-pass 1.2 m absorption cell. A 50 ppmv mixture of CH₄ in N₂ was introduced into the cell along with benzene vapor to calibrate benzene concentration measurements. Benzene mixing ratios down to ∼90 ppmv were measured using a direct absorption technique. The minimum detectable absorbance and detection limit of benzene were estimated to be ∼10⁻⁴ and 30 ppmv, respectively. Using the wavelength modulation technique, we measured a second harmonic sensor response to benzene vapor absorption in air at atmospheric pressure as a function of modulation index. We conclude that a low-temperature monolithic VCSEL operating near 1684 nm can be employed in compact benzene sensors with a detection limit in the sub-ppm range.     

Kinetic Fluorimetric Measurement of Trace Resorcinol1 in Phenol Mixtures

A kinetic spectrofluorimetric method was studied to measure the concentration of trace resorcinol. The proposed method is based on the inhibitory effect of resorcinol on the oxidation of rhodamine B by potassium bromate in the medium of dilute sulfuric acid. The detection limit and linear range of the proposed resorcinol measurement method are 12 μg L⁻¹ and 24∼280 μg L⁻¹, respectively. Relative standard derivations of eleven measurements for 80 μg L⁻¹ and 200 μg L⁻¹ resorcinol solutions are 2.12% and 1.08%, respectively. The trace of resorcinol can be determined directly by the proposed method without any pre-separation process when phenol and many other phenolic compounds are present.     

Fabrication of a nanoparticle TiO<Subscript>2</Subscript> photoelectrochemical cell utilizing a solid polymeric electrolyte of PAN–PC–LiClO<Subscript>4</Subscript>

A nanoparticle TiO₂ solid-state photoelectrochemical cell utilizing as a solid electrolyte of poly(acrylonitrile)–propylene–carbonate–lithium perchlorate (PAN–PC–LiClO₄) has been fabricated. The performance of the device has been tested in the dark and under illumination of 100-mW cm⁻² light. A nanoparticle TiO₂ film was deposited onto indium tin oxide-covered glass substrate by controlled hydrolysis technique assisted with spin-coating technique. The average grain size for the TiO₂ film is 76 nm. LiClO₄ salt was used as a redox couple. The room temperature conductivity of the electrolyte is 4.2 × 10⁻⁴ S cm⁻¹. A graphite electrode was prepared onto a glass slide by electron beam evaporation technique. The device shows the rectification property in the dark and shows the photovoltaic effect under illumination. The best J _sc and V _oc of the device were 2.82 μA cm⁻² and V _oc of 0.58 V, respectively, obtained at the conductivity of 4.2 × 10⁻⁴ S cm⁻¹ and intensity of 100 mW cm⁻². The J _sc was improved by about three times by introducing nanoparticle TiO₂ and by using a solid electrolyte of PAN–PC–LiClO₄ replacing PVC–PC–LiClO₄ in the device. The current transport mechanism of the cell is also presented in this paper.     

Sonochemical synthesis and fabrication of perovskite type calcium titanate interfacial nanostructure supported on graphene oxide sheets as a highly efficient electrocatalyst for electrochemical detection of chemotherapeutic drug

In green approaches for electrocatalyst synthesis, sonochemical methods play a powerful role in delivering the abundant surface areas and nano-crystalline properties that are advantageous to electrocatalytic detection. In this article, we proposed the sphere-like and perovskite type of bimetal oxides which are synthesized through an uncomplicated sonochemical procedure. As a yield, the novel calcium titanate (orthorhombic nature) nanoparticles (CaTiO₃ NPs) decorated graphene oxide sheets (GOS) were obtained through simple ultrasonic irradiation by a high-intensity ultrasonic probe (Titanium horn; 50 kHz and 60 W). The GOS/CaTiO₃ NC were characterized morphologically and chemically through the analytical methods (SEM, XRD, and EDS). Besides, as-prepared nanocomposites were modified on a GCE (glassy carbon electrode) and applied towards electrocatalytic and electrochemical sensing of chemotherapeutic drug flutamide (FD). Notably, FD is a crucial anticancer drug and also a non-steroidal anti-androgen chemical. Mainly, the designed and modified sensor has shown a wide linear range (0.015–1184 µM). A limit of detection was calculated as nanomolar level (5.7 nM) and sensitivity of the electrode is 1.073 μA μM⁻¹ cm⁻². The GOS/CaTiO₃ modified electrodes have been tested in human blood and urine samples towards anticancer drug detection.     

CO2 isotope sensor using a broadband infrared source, a spectrally narrow 4.4 μm quantum cascade detector, and a Fourier spectrometer

We report a prototype CO₂ gas sensor based on a simple blackbody infrared source and a spectrally narrow quantum cascade detector (QCD). The detector absorption spectrum is centered at 2260 cm⁻¹ (4.4 μm) and has a full width at half maximum of 200 cm⁻¹ (25 meV). It covers strong absorption bands of two spectrally overlapping CO₂ isotopomers, namely the P-branch of ¹²CO₂ and the R-branch of ¹³CO₂. Acquisition of the spectral information and data treatment were performed in a Fourier transform infrared (FTIR) spectrometer. By flushing its sample compartment either with nitrogen, dry fresh air, ambient air, or human breath, we were able to determine CO₂ concentrations corresponding to the different gas mixtures. A detection limit of 500 ppb was obtained in these experiments.     

Fluorescence and Electrochemical Sensing of Pesticides Methomyl, Aldicarb and Prometryne by the Luminescent Europium-3-Carboxycoumarin Probe

This work describes the application of time resolved fluorescence in microtiterplates and electrochemical methods on glassy carbon electrode for investigating the interactions of europium-3-carboxycoumarin with pesticides aldicarb, methomyl and prometryne. Stern-volmer studies at different temperatures indicate that static quenching dominates for methomyl, aldicarb and prometryne. By using Lineweaver-Burk equation binding constants were determined at 303 K, 308 K and 313 K. A thermodynamic analysis showed that the reaction is spontaneous with ΔG being negative. The enthalpy ΔH and the entropy ΔS of reactions were all determined. A time-resolved (gated) luminescence-based method for determination of pesticides in microtiterplate format using the long-lived europium-3-carboxycoumarin has been developed. The limit of detection is 4.80, 5.06 and 8.01 μmol L⁻¹ for methomyl, prometryne and aldicarb, respectively. This is the lowest limit of detection achieved so far for luminescent lanthanide-based probes for pesticides. The interaction of the probe with the pesticides has been investigated using cyclic voltammetry (CV), differential pulse polarography (DPP), square wave voltammetry (SWV) and linear sweep voltammetry (LSV) on a glassy carbon electrode in I = 0.1 mol L⁻¹ p-toluenesulfonate at 25 °C. The diffusion coefficients of the reduced species are calculated. The main properties of the electrode reaction occurring in a finite diffusion space are the quasireversible maximum and the splitting of the net SWV peak for Eu(III) ions in the ternary complex formed . It was observed that the increase of the cathodic peak currents using LSV is linear with the increase of pesticides concentration in the range 5 × 10⁻⁷ to 1 × 10⁻⁵ mol L⁻¹. The detection limit (DL) were about 1.01, 2.23 and 1.89 μmolL⁻¹ for aldicarb, methomyl and prometryne, respectively. In order to assess the analytical applicability of the method, the influence of various potentially interfering species was examined. Influence of interfering species on the recovery of 10 μmol L⁻¹ pesticides has been investigated.     

A Fe<Superscript>3+</Superscript>/Hg<Superscript>2+</Superscript>-Selective Anthracene-Based Fluorescent PET Sensor with Tridentate Ionophore of Amide/β-Amino Alcohol

A new anthracene-based fluorescent PET sensor 1 with a tridentate ionophore of amide/β-amino alcohol displays very good selectivity and sensitivity for Fe³⁺ (K _a = 1.6 × 10³ M⁻¹) and Hg²⁺ (K _a = 2.1 × 10³ M⁻¹) in CH₃CN–H₂O (3:7, v/v) with detection limit of 1 μM. More fluorescence enhancement was observed when 1 selectively detected Fe³⁺ or Hg²⁺ in CH₃CN and its detection limit was up to 0.03 μM.     

Measurements of the temperature and water vapor concentration in a hot zone by tunable diode laser absorption spectrometry

A tunable diode laser absorption spectroscopy (TDLAS) technique and appropriate instrumentation was developed for the measurement of temperature and water vapor concentrations in heated gases. The technique is based on the detection of the spectra of H₂O absorption lines with different energies of low levels. The following absorption lines of H₂O were used: 7189.344 cm⁻¹ (E″=142 cm⁻¹), 7189.541 cm⁻¹ (E″=1255 cm⁻¹), 7189.715 cm⁻¹ (E″=2005 cm⁻¹). Spectra were recorded using fast frequency scanning of a single distributed feedback (DFB) laser. A unique differential scheme for the recording of the absorption spectra was developed. An optimal technique for fitting the experimental spectra was developed.     

Analysis of trace impurities in semiconductor gas via cavity-enhanced direct frequency comb spectroscopy

Cavity-enhanced direct frequency comb spectroscopy (CE-DFCS) has demonstrated powerful potential for trace-gas detection based on its unique combination of high bandwidth, rapid data acquisition, high sensitivity, and high resolution, which is unavailable with conventional systems. However, previous demonstrations have been limited to proof-of-principle experiments or studies of fundamental laboratory science. Here, we present the development of CE-DFCS towards an industrial application—measuring impurities in arsine, an important process gas used in III–V semiconductor compound manufacturing. A strongly absorbing background gas with an extremely complex, congested, and broadband spectrum renders trace detection exceptionally difficult, but the capabilities of CE-DFCS overcome this challenge and make it possible to identify and quantify multiple spectral lines associated with water impurities. Further, frequency combs allow easy access to new spectral regions via efficient nonlinear optical processes. Here, we demonstrate detection of multiple potential impurities across 1.75–1.95 μm (5710–5130 cm⁻¹), with a single-channel detection sensitivity (simultaneously over 2000 channels) of ∼4×10⁻⁸ cm⁻¹ Hz^−1/2 in nitrogen and, specifically, an absorption sensitivity of ∼4×10⁻⁷ cm⁻¹ Hz^−1/2 for trace water doped in arsine.     

One-pot fabrication and enhanced thermoelectric properties of poly(3,4-ethylenedioxythiophene)-Bi<Subscript>2</Subscript>S<Subscript>3</Subscript> nanocomposites

Bi₂S₃ nanotubes and de-doped poly(3,4-ethylenedioxythiophene) (PEDOT) composite nanopowders were synchronously synthesized by a one-pot self-assembly method. The powders were characterized by X-ray powder diffraction, infrared spectroscopy, and transmission electron microscopy, respectively. Thermoelectric properties of the Bi₂S₃–PEDOT composite nanopowders with different Bi₂S₃ contents after being cold pressed into pellets were measured at room temperature. The sample with 36.1 wt% Bi₂S₃ has a highest power factor of 2.3 μWm⁻¹K⁻², which is higher than that of both pure PEDOT (0.445 μWm⁻¹K⁻²) and Bi₂S₃ (1.94 μWm⁻¹K⁻²).     

Anhydrous proton-conducting organic–inorganic hybrid membranes synthesized from tetramethoxysilane/methyltrimethoxysilane/diisopropyl phosphite and ionic liquid

Inorganic–organic hybrid membranes were prepared by sol–gel process with tetramethoxysilane/methyltrimethoxysilane/diisopropyl phosphite and 1-butyl-3-methylimidazolium tetrafluoroborate (BMIMBF₄) ionic liquid as precursors. The Fourier transform infrared spectroscopy (FT-IR) and ³¹P, ²⁹Si, ¹H, ¹³C, and ¹⁹F nuclear magnetic resonance measurements have shown good chemical stability and complexation of (POH[(CH₃)₂CHO]₂) with [BMIMBF₄] ionic liquid in the fabricated hybrid membranes. The influence of the textural properties of all the prepared composite membranes could be interpreted from nitrogen adsorption–desorption measurements. The average pore size was increased proportionally with the ionic liquid weight percent ratio in the host phosphosilicate matrix from 2.59 to 11.71 nm, respectively. Thermogravimetric analysis and differential thermal analysis measurements confirmed that the hybrid membranes were thermally stable up to 260 °C. Thermal stability of the hybrid membranes was significantly enhanced by the presence of inorganic SiO₂ framework and high stability of [BF₄] anion. For all the composite membranes, the conductivities were measured within the temperature range (−30 °C) to 150 °C, and a maximum conductivity of 7 × 10⁻³ S/cm at 150 °C was achieved for 40 wt.% ionic liquid-based composite membrane under nonhumidified conditions.     

Electrochemical study of P(VDF-HFP)/PMMA blended polymer electrolyte with high-temperature stability for polymer lithium secondary batteries

In the present study, a kind of solid polymer electrolyte (SPE) based on poly(vinylidene difluoride-co-hexafluoropropylene)/poly(methyl methacrylate) blends was prepared by a casting method to solve the safety problem of lithium secondary batteries. Owing to being plasticized with a room temperature ionic liquid, N-butyl-N′-methyl-imidiazolium hexafluorophosphate, the obtained SPE shows a thermal decomposition temperature over 300°C and an ionic conductivity close to 10⁻³ S cm⁻¹. The SPE-3 sample, in which the weight of two polymers is equivalent, possesses an ionic conductivity of 0.45 × 10⁻³ S cm⁻¹ at 25°C and presents an electrochemical window of 4.43 V. The ionic conductivity of the SPE-3 is as high as 1.73 × 10⁻³ S cm⁻¹ at 75°C approaching to that of liquid electrolyte. The electrochemical performances of the Li/LiFePO₄ cells confirmed its feasibility in lithium secondary batteries.     

Mid-infrared laser-absorption diagnostic for vapor-phase fuel mole fraction and liquid fuel film thickness

A novel two-wavelength mid-infrared laser-absorption diagnostic has been developed for simultaneous measurements of vapor-phase fuel mole fraction and liquid fuel film thickness. The diagnostic was demonstrated for time-resolved measurements of n-dodecane liquid films in the absence and presence of n-decane vapor at 25°C and 1 atm. Laser wavelengths were selected from FTIR measurements of the C–H stretching band of vapor n-decane and liquid n-dodecane near 3.4 μm (3000 cm⁻¹). n-Dodecane film thicknesses <20 μm were accurately measured in the absence of vapor, and simultaneous measurements of n-dodecane liquid film thickness and n-decane vapor mole fraction (300 ppm) were measured with <10% uncertainty for film thicknesses <10 μm. A potential application of the measurement technique is to provide accurate values of vapor mole fraction in combustion environments where strong absorption by liquid fuel or oil films on windows make conventional direct absorption measurements of the gas problematic.     

Bacto agar-based gel polymer electrolyte

The biopolymer of a Bacto agar-based gel polymer electrolyte (GPE) was prepared by addition of NaI and I₂ as redox couple. The prepared GPE was characterized using impedance spectroscopy and X-ray diffraction (XRD) in order to determine its electrical and structural properties, respectively. An optimized ionic conductivity of 12.41 × 10⁻⁴ S cm⁻¹ was achieved for the samples containing 1.6 M NaI and 50 μL I₂. Meanwhile, XRD revealed that the addition of NaI and I₂ altered agar properties and formed an amorphous structure. Linear sweep voltammetry showed that the electrochemical stability window of the sample had a working voltage of 2.0 V.     

Application of ionic liquid doped solid polymer electrolyte

The electrical, structural, and photoelectrochemical properties of the polymer electrolyte PEO:NaI/I₂ doped with an ionic liquid 1-ethyl 3-methylimidazolium dicyanamide (EMImDCN) have been reported. Incorporation of the ionic liquid (IL) increases the membrane homogeneity, decreased surface roughness, and enhances the short current (J _sc). Additionally, the doping of IL provides more charge carriers which enhances overall ionic conductivity (σ). The optimized σ was found at 40 wt.% IL composition. The fabricated DSSC using this new solid electrolyte showed 1.43% efficiency at 100 mW cm⁻².     

Wavelength modulation and cavity enhanced absorption spectroscopy using ～1.9?μm radiation produced by difference frequency generation with a MgO doped PPLN crystal

We have demonstrated the production of ∼1.9 μm near-infrared radiation by using difference frequency generation within a 5% MgO doped PPLN crystal by coupling ∼735 nm radiation from a tunable external cavity diode laser with relatively high powered 532 nm radiation from both Nd:YVO₃ and Nd:YAG lasers. The radiation produced is of low power, ∼15 μW, and was used in conjunction with the sensitivity enhancing techniques of wavelength modulation spectroscopy (WMS) and cavity enhanced absorption spectroscopy (CEAS). Experiments were carried out on rotationally resolved transitions in the combination bands of NH₃ and CO₂ in the 1.9 μm region. An α _min value of 3.6×10⁻⁶ cm⁻¹ Hz^−1/2 was achieved for WMS measurements on CO₂. A comparable α _min value of 2.2×10⁻⁶ cm⁻¹ Hz^−1/2 was achieved for NH₃ using CEAS. The low NIR power indicates that despite the level of MgO doping quoted for the crystal, under prolonged exposure photorefractive damage has occurred.     

Laser induced breakdown spectroscopy of germane plasma induced by IR CO2 pulsed laser

Laser-induced breakdown spectroscopy (LIBS) in germane (GeH₄), initially at room temperature and pressures ranging from 2 to 10 kPa, was studied using a high-power transverse excitation atmospheric (TEA) CO₂ laser (λ=10.653 μm, τ _FWHM=64 ns and power densities ranging from 0.28 to 5.52 GW cm⁻²). The strong emission spectrum of the generated plasma is mainly due to electronic relaxation of excited Ge, H and ionic fragments Ge⁺, Ge²⁺ and Ge³⁺. The weak emission is due to molecular bands of H₂. Excitation temperatures of 8100±300 K and 23,500±2500 K were estimated by Ge atomic and Ge⁺ singly ionized lines, respectively. Electron number densities of the order of (0.7–6.2)×10¹⁷ cm⁻³ were deduced from the Stark broadening of several atomic Ge lines. The characteristics of the spectral emission intensities from different species have been investigated as functions of the germane pressure and laser irradiance. Optical breakdown threshold intensities in germane at 10.653 μm have been determined. The mechanism of initiation of the laser-induced plasma in germane has been analyzed.