Preparation of Cd-doped SnO<Subscript>2</Subscript> nanoparticles by sol–gel route and their optical properties

Nanocrystalline cadmium doped tin oxide (SnO₂) powders of about 2.5–4.5 nm in size have been synthesized by using different solvents via sol–gel method. The obtained samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), Energy dispersive X-ray analysis (EDX), Transmission electron spectroscopy (TEM), UV-Vis absorption and Photoluminescence (PL) spectroscopy. The PL emission spectra revealed that the band centered at 452 nm might be related with oxygen vacancies. A spherical, small rod and slice like morphologies of the prepared Cd-SnO₂ nanoparticles were observed in the SEM and TEM studies. The presence of Cd modifies the structural, morphological and optical properties of the tin oxide nanoparticles.     

Preparation of nanocrystalline CuAlO<Subscript>2</Subscript> through sol–gel route

Nanocrystalline powders of CuAlO₂ were synthesized through sol–gel method using nitrate-citrate route and also through solid state reaction method. We used a new set of precursor materials for the synthesis of CuAlO₂ through sol–gel route which were not reported in the past. A little lowering of the synthesis temperature (1,000 °C) was observed in case of sol–gel process compared to the solid state reaction method (1,100 °C) and also at shorter time duration. The particle size of the synthesized powders was determined through small angle X-ray scattering. It has been observed that the particle size prepared by nitrate-citrate technique is less than the particle size prepared by the solid-state reaction method. Chemical states of the atomic species were determined by X-ray photoelectron spectroscopy. The formation of phase pure CuAlO₂ were also confirmed by Fourier transformed infrared spectroscopy. A number of solvents were also used for finding the best possible combinations for obtaining phase pure CuAlO₂ at 1,000 °C and it was observed that only the combination of nitrate salts, citric acid and ethanol resulted phase pure CuAlO₂.     

Preparation of Ga<Subscript>2</Subscript>Se<Subscript>3</Subscript> thin films by sol–gel technique

In this study we describe the preparation of Ga₂Se₃ semiconductor compound thin films by sol–gel method for different crystal formation temperatures. The films were characterized by X-ray diffraction analyses (XRD), UV–visible spectrometer, and scanning electron microscope (SEM). The XRD spectrum showed that the formation of Ga₂Se₃ crystals were between 743 and 823 K. The thin film crystals that were formed at 773 K corresponded to the β phase and the preferred crystal structure was monoclinic. The value of band gap from optical absorption spectra for the Ga₂Se₃ thin films was estimated to be about E _g ~ 2.56 eV. The thickness of the one-coat Ga₂Se₃ thin films, which was measured by a Spectroscopic Ellipsometer, was about ~200 nm. The average grain sizes of scattered particles were within the limits between 200 and 500 nm.     

Preparation and characterisation of NdAlO<Subscript>3</Subscript> nanocrystals by modified sol–gel method

Nanocrystalline single-phase neodymium monoaluminate (NdAlO₃) has been prepared from neodymium oxide and aluminium nitrate by modified Pechini’s method. Malic acid has been used for the first time as a new complexing agent in the sol–gel process. It has facilitated, without adding 1,2-ethanediol, a low-temperature synthesis at 1,050 °C compared to the temperature of 1,630 °C needed for the solid-state preparation. The characterisation of the nanoparticles has been carried out by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and infrared spectroscopy in the range 75–4,000 cm⁻¹. The smallest particles have size of 30 nm and are anisometric; agglomerates of particles have been also observed. The material has pyknometric density of 3.956 g/cm³ at T = 293.15 K and specific surface area 5.2 m²/g. The binding energies of O 1s, Al 2p, Nd 3d, and Nd 4d electrons have been found chemically shifted in NdAlO₃ compared to the values for the respective elements.     

NiTiO<Subscript>3</Subscript> nanoparticles encapsulated with SiO<Subscript>2</Subscript> prepared by sol–gel method

NiTiO₃ (NTO) nanoparticles encapsulated with SiO₂ were prepared by the sol–gel method resulting on core-shell structure. Changes on isoelectric point as a function of silica were evaluated by means of zeta potential. The NTO nanoparticles heat treated at 600°C were characterized by X-ray diffraction, transmission electron microscopy (TEM) and energy dispersive X-ray analysis. TEM observations showed that the mean size of NTO is in the range of 2.5–42.5 nm while the thickness of SiO₂ shell attained 1.5–3.5 nm approximately.     

Preparation and electrochemical properties of V<Subscript>2</Subscript>O<Subscript>5</Subscript> submicron-belts synthesized by a sol–gel H<Subscript>2</Subscript>O<Subscript>2</Subscript> route

One-dimensional (1D) submicron-belts of V₂O₅ have been prepared by a sol–gel route using V₂O_5, H₂O₂ and aniline as starting materials. Thermogravimetric and differential thermal analysis, X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy were employed to characterize the samples. Electrochemical behaviors as cathode material in rechargeable lithium-ion batteries were investigated by galvanostatic charge–discharge measurement and cyclic voltammeter. The results showed that the synthesized V₂O₅ appeared to be submicron-belts and orthorhombic structure. The V₂O₅ submicron-belts exhibited a high initial discharge capacity of 346 mAh/g and stayed 240 mAh/g after 20 cycles at 0.1 C discharge rate in the potential region 1.8–4.0 V.     

Structure and dielectric properties of HfO<Subscript>2</Subscript> films prepared by a sol–gel route

Mono- and multilayer HfO₂ sol–gel thin films have been deposited on silicon wafers by dip-coating technique using a solution based on hafnium ethoxide as precursor. The densification/crystallization process was achieved by classical annealing between 400 and 600 °C for 0.5 h (after drying at 100 °C). Systematic TEM studies were performed to observe the evolution of the thin film structure depending on the annealing temperature. The overall density of the films was determined from RBS spectrometry correlated with cross section (XTEM) thickness measurements. After annealing at 450 °C the films are amorphous with a nanoporous structure showing also some incipient crystallization. After annealing at 550 °C the films are totally crystallized. The HfO₂ grains grow in colonies having the same crystalline orientation with respect to the film plane, including faceted nanopores. During annealing a nanometric SiO₂ layer is formed at the interface with the silicon substrate; the thickness of this layer increases with the annealing temperature. Capacitive measurements allowed determining the value of the dielectric constant as 25 for four layer films, i.e. very close to the value for the bulk material.     

Facile and ultra large scale synthesis of nearly monodispersed CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by a low temperature sol–gel route

Nearly monodispersed cobalt ferrite nanoparticles were synthesized by a low temperature sol–gel route using propylene oxide as a gelation agent. The nanoparticles were obtained by the reaction of FeCl₂ and CoCl₂ in ethanol solution with propylene oxide to form the sol, followed by the boiling of the sol solution. The unique chemistry of this procedure allows the formation of highly homogeneous gel intermediate, resulting in the great reducing of crystallization temperature of ferrites to less than 100 °C without postannealing step. This guarantees the preparation of well defined and non-aggregated ferrite nanoparticles on an ultra-large scale of about 75 g in a single reaction. This large scale synthesis strategy offers important advantages over other conventional routes for the preparation of CoFe₂O₄ nanoparticles, showing the promising application of this route in the industrial production.     

Preparation of HfB<Subscript>2</Subscript>/SiC composite powders by sol–gel technology

Sol–gel technology was used to chemically modify the surface of HfB₂ powders with highly dispersed silicon carbide using two carbothermy protocols: (1) under heating to 1500°С in flowing argon (100 mL/min) without exposure and (2) under dynamic vacuum conditions (p ~ 1 × 10^–5–1 × 10^–6 MPa) at 1400°С with 4-h exposure. The phase composition and microstructural features of the thus-prepared HfB₂/xSiC (x = 10–65 vol %) composite powders were studied. The products prepared by the second protocol showed an enhanced oxidation resistance in the range 20–1400°C in flowing air compared to individual HfB₂.     

Low temperature and size controlled synthesis of monodispersed γ-Fe<Subscript>2</Subscript>O<Subscript>3 </Subscript>nanoparticles by an epoxide assisted sol–gel route

Monodispersed γ-Fe₂O₃ nanoparticles were prepared by a procedure-simple and precursor-cheap route, epoxide assisted sol–gel method. The γ-Fe₂O₃ nanoparticles were obtained by the reaction of FeCl₂ in ethanol solution with propylene oxide to form the sol, following by the boiling of the solution. As compared with other metal ions of +2 formal charge, the unexpected acidity of FeCl₂ in ethanol solution assure the formation of sol. As an advantage, the unique chemistry of this route results in the low temperature of synthesis, leading to the extremely small particle size of 2.3 nm and non-aggregation state of the particles.     

Simple sol–gel route to synthesis of mesoporous TiO<Subscript>2</Subscript>

Mesoporous TiO₂ with a high specific surface area was prepared from titanium sulfate solution in a simple sol–gel route, where formamide was used as pH adjusting agent. TiO₂ had a high resistance to phase transformation, and maintained monophasic anatase after calcinating at 600 °C. The highest specific surface area achieved on the prepared samples is 231.90 m² g⁻¹ after calcinating at 450 °C.     

Preparation and characterization of SiO<Subscript>2</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Na<Subscript>2</Subscript>O glass coated cBN abrasive particles via sol–gel route

SiO₂–Al₂O₃–Na₂O glass coated cubic boron nitride (cBN) abrasive particles were prepared by sol–gel technique. The results indicated that SiO₂–Al₂O₃–Na₂O glass was excellent material for oxidation protection of cBN abrasive grains because coefficient of thermal expansion of this glass closely matched that of cBN materials. The single particle compressive strength and impact toughness of this glass coated cBN abrasive particles were significantly increased. For the application of glass coated cBN abrasives to vitrified grinding wheels, it was evident that the glass coating provided high bonding strength between cBN abrasive grains and vitrified bond system.     

Preparation of highly stable TiO<Subscript>2</Subscript> sols and nanocrystalline TiO<Subscript>2</Subscript> films via a low temperature sol–gel route

Highly stable TiO₂ sols were prepared by adjusting the water-to-titanium molar ratio to ~4 in the process of hydrolysis and condensation of titanium isopropoxide in ethanol with HNO₃. Particularly, long-term stable TiO₂ sols were prepared without adding any chemical additives. Anatase TiO₂ nanocrystallites with sizes of 3–5 nm in diameter were uniformly dispersed in the stable sol. Crystallized TiO₂ films were successfully deposited on Si (100) using the stable sol via a dip-coating process with low temperature curing at as low as 100 °C. The synthesized TiO₂ sols and films are promising for use in flexible or dye-sensitized solar cells.     

Electrochromic properties of MoO<Subscript>3</Subscript> thin films derived by a sol–gel process

Molybdenum trioxide (MoO₃) films were deposited on ITO/Glass substrates by the sol–gel method using a spin-coating technique and heat treated at various temperatures under different ambient atmosphere. Effects of the process parameters on the electrochromic properties of MoO₃ films were studied using cyclic voltammetry (CV) in a propylene carbonate (PC) non-aqueous solution containing 1 M lithium perchlorate (LiClO₄). Electrochromic MoO₃ film on lithium intercalation was investigated by in-situ transmittance measurement during the CV process. The MoO₃ films showed reversible recharge ability on Li⁺/e⁻ intercalation/deintercalation. Experimental results revealed that the heat-treatment temperature, the ambient atmosphere, and the thickness will have the string influence on the electrochromic properties of MoO₃ thin films. X-ray diffraction (XRD) results show that the amorphous MoO₃ films can be obtained with the heat-treatment temperature below 300 °C in O₂ ambient atmosphere. The optimum electrochromic MoO₃ film, with a thickness of 130 nm, exhibits a maximum transmittance variation (ΔT%) of 30.9%, an optical density change (ΔOD) of 0.213, an intercalation charge (Q) of 8.47 mC/cm², an insertion coefficient x in Li _x MoO₃ was 0.21 and a coloration efficiency (η) of 25.1 cm²/C between the colored and bleached states at a wavelength (λ) of 550 nm.     

Preparation of LiCoPO<Subscript>4</Subscript> powders and films via sol–gel

Lithium intercalation materials are of special interest as cathodes in rechargeable batteries. An uncomplicated sol–gel process has been used for the synthesis of Li–Co phosphates powders and, for the first time, of LiCoPO₄ films. The powders were prepared from aqueous solutions, containing Li, Co and phosphate precursors to which acid citric and ethylene glycol was added, during the drying process at 75 °C. The X-ray diffraction patterns of the prepared powders confirmed the presence of LiCoPO₄ with an olivine-like structure as main phase. The morphological investigations of the powder showed a platelet-like structure with an average grain size of 0.75 μm. The films of LiCoPO₄ were deposited onto ITO glass substrates with the combination of the dip-coating process under the same conditions. Finally, the films were annealed in inert atmosphere at 300 °C. The morphological investigations reveal a smooth and homogeneous surface of the prepared Li–Co phosphate films. The preliminary electrical investigation on the prepared LiCoPO₄ films showed lithium ions electrochemical activity in the range 3.0–4.5 V.     

Synthesis of CaSnO<Subscript>3</Subscript> nanofibers by electrospinning combined with sol–gel

Calcium stannate (CaSnO₃) nanofibers were synthesized by electrospinning technique combined with a sol–gel process. The structure and morphology of the as-prepared CaSnO₃ nanofibers were characterized by X-ray diffraction and scanning electron microscopy, respectively. The samples had a band gap of about 3.87 eV, which was estimated by UV–Vis diffuse reflectance spectroscopy. On the basis of the experiment results, the composite fibers containing polymer and inorganic salt can be changed to pure CaSnO₃ nanofibers only when they were sintered at an appropriate temperature. At the same time, a possible mechanism of the nanofibers forming process was also proposed.     

Preparation of nanostructured thin films of yttrium iron garnet (Y<Subscript>3</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript>) by sol–gel technology

The synthesis of hydrolytically active heteroligand coordination compounds [M(C₅H₇O₂)_3?x(C₅H₁₁Oⁱ)_x] (M = Fe³⁺ and Y³⁺) using iron and yttrium acetylacetonates has been studied. The gel formation kinetics in solutions of these compounds upon hydrolysis and polycondensation has also been studied. Thin films of a solution of these precursors have been applied to polished sapphire substrates by dip coating technology. The crystallization of nanostructured yttrium iron garnet (Y₃Fe₅O₁₂) films during heat treatment of xerogel coatings under various conditions has been studied. How the phase composition, microstructure, and particle size depend on the synthesis parameters has been recognized.     

Preparation and characterization of TiO<Subscript>2</Subscript> sol–gel modified nanocomposite films

In this study, the role of TiO₂ MT-150A loading in the polymeric sol was investigated for the synthesis of immobilized TiO₂ nanocomposite films on glass substrate using the MT-150A nanoparticles-modified sol–gel method. The nanocomposite film properties were examined using different material characterization techniques including X-ray diffraction, X-ray photoelectron spectroscopy, field emission scanning electron microscopy, UV–Vis spectrophotometer, Scotch tape test and pencil hardness test. The hydrophilicity of films during UV/Vis irradiation and storage in a dark place were evaluated by a contact angle analyzer. The MT-150A loading had a significant effect on the amount of crystallite phases in the films. However, increasing the MT-150A loading in the sol resulted in an increase in rutile phase content. In addition, increasing MT-150A loading in the sol yielded films with higher hydrophilicity but a concentration of 10–30 g/L MT-150A in the sol was found as the maximum for obtaining films with good adherence on the glass substrate.     

Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-based pigments synthesized by a new proteic sol–gel method

Alumina-based pigments were synthesized by the proteic sol–gel method. In this method, coconut water is employed as polymeric agent instead of the conventional alkoxide precursors. To this study, three common chromophore metallic ions (Mn³⁺, Co³⁺, and Cr³⁺) were chosen in order to verify the method efficiency. Differential thermal analysis (DTA), thermogravimetry (TG), and XRD techniques were used to characterize the synthesis process. The colorimetric characterization of the produced pigments was done according to the CIE-L*a*b* 1976 norm which is recommended by the CIE (International Commission on Illumination). The synthesized pigments presented intense and uniform colors in accordance to the literature results for each chromophore ion. The produced pigments also presented agglomerated with an average grain size of 180 nm when calcined at 800 °C.