Microheterogeneity evaluation of polycyclic aromatic hydrocarbons in particulate standard reference materials

With the emergence of highly sensitive analytical techniques, the microanalysis of natural-matrix materials employing smaller sample sizes is increasingly more common, which subsequently warrants a homogeneity assessment for the individual components at the appropriate sampling level. Pressurized liquid extraction (PLE) in combination with gas chromatography/mass spectrometry (GC/MS) has been used to determine the sampling constants and evaluate the relative homogeneity of trace levels of polycyclic aromatic hydrocarbons (PAHs) for two previously certified particulate standard reference materials, SRM 1649a Urban Dust and SRM 1650b Diesel Particulate Matter, in the milligram sampling range. Fluoranthene, pyrene, benz[a]anthracene and benzo[e]pyrene within SRM 1650b Diesel Particulate Matter were deemed to be homogeneous, based on relatively small sampling constants (K _S<100 mg), whereas the larger sampling constants (K _S>100 mg) obtained for all PAHs in SRM 1649a Urban Dust suggest more material heterogeneity. The material heterogeneity of ten individual PAHs (phenanthrene, anthracene, fluoranthene, pyrene, benz[a]anthracene, benzo[k]fluoranthene, benzo[e]pyrene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene and benzo[ghi]perylene) was also described via nonlinear relationships (i.e., power law) between subsampling error S _s (%) and sample mass, which are used to predict analyte-specific minimum sample masses that result in a specific level of analytical uncertainty. Electronic supplementary material Supplementary material is available for this article at and is accessible for authorized users.     

Determination of selected oxygenated polycyclic aromatic hydrocarbons (oxy-PAHs) in diesel and air particulate matter standard reference materials (SRMs)

Oxygenated polycyclic aromatic hydrocarbons (oxy-PAHs) have recently received much attention in discussions regarding the negative impacts of particulate matter (PM) on human health and the environment. The National Institute of Standards and Technology provides several environmental matrix standard reference materials (SRMs) with certified and reference values for polycyclic aromatic hydrocarbons (PAHs) and nitrated PAHs. In this study, the concentrations of oxygenated PAHs are determined in three air PM SRMs (1649b, 1648a, and 2786) and three diesel PM SRMs (1650b, 2975, and 1975) using two independent gas chromatography–mass spectrometry methods. Concentrations of oxy-PAHs were at the milligrams per kilogram level with higher overall concentrations in diesel PM (up to 50 mg/kg for 9,10-anthraquinone). One of the highest oxy-PAH concentrations (up to 5 mg/kg) measured in the air particulate SRMs was for 7,12-benz[a]anthracenquinone. These results suggest that oxygenated PAHs should not be neglected in the analysis of PM as their concentrations can be as high as those of some PAHs and are one to two orders of magnitude higher than those for nitro-PAHs.     

Optimisation of the extraction of polycyclic aromatic hydrocarbons and their nitrated derivatives from diesel particulate matter using microwave-assisted extraction

Pressurised microwave-assisted extraction was used to extract a complex mixture containing polycyclic aromatic hydrocarbons (PAHs), nitrated PAHs and heavy n-alkanes from a particularly refractory carbonaceous material resulting from the combustion in a diesel engine. A second-order central composite design was used to determine the optimal conditions of extraction in terms of time, temperature, volume and nature of extracting solvent from spiked diesel soots. To begin, methylene chloride, tetrahydrofuran and chloroform were tested for extracting the spiked diesel particulates; however, the nature of these solvents was not really an influential factor. Volume was the most influential factor and was kept at a medium level to enhance the extraction of heavy PAHs without introducing an important dilution factor. Temperature and time were not influential as main factors but interacted with the other factors. Finally, high temperature and duration associated with a medium volume of methylene chloride were better for the extractions. After this optimisation, five-ring and six-ring PAHs were nevertheless not satisfactorily desorbed. Other solvents were therefore tested. Only aromatic ones, and particularly heterocyclic aromatic solvents, managed to desorb the heaviest PAHs. Pyridine, with its both aromatic and its basic character, was the most successful solvent. Desorption was even complete with an addition of 17% of diethylamine into pyridine. So, using MAE, we succeeded in extracting quantitatively, from the spiked refractory diesel soot surface, two-ring to six-ring PAHs, heavy n-alkanes and short nitrated PAHs. However, heavy nitrated PAHs were better extracted with a small addition of acetic acid (1%) into pyridine instead of a basic cosolvent.     

Determination of nitrated polycyclic aromatic hydrocarbons in diesel particulate-related standard reference materials by using gas chromatography/mass spectrometry with negative ion chemical ionization

Gas chromatography/mass spectrometry (GC/MS) with negative ion chemical ionization (NICI) detection was utilized for quantitative determination of nitrated polycyclic aromatic hydrocarbons (nitro-PAHs) in diesel particulate-related standard reference materials (SRMs). Prior to GC/MS analysis, isolation of the nitro-PAHs from the complex diesel particulate extract was accomplished using solid phase extraction (SPE) and normal-phase liquid chromatographic (LC) fractionation using an amino/cyano stationary phase. Concentrations of eight to ten mononitro-PAHs and three dinitropyrenes were determined in three diesel particulate-related SRMs: SRM 1650a Diesel Particulate Matter, SRM 1975 Diesel Particulate Extract, and SRM 2975 Diesel Particulate Matter (Industrial Forklift). The results from GC/MS NICI using two different columns (5% phenyl methylpolysiloxane and 50% phenyl methylpolysiloxane) were compared to each other and to results from two other laboratories for selected nitro-PAHs. 1-Nitropyrene was the most abundant nitro-PAHs in each of the diesel particulate SRMs (19.8+/-1.1 micro g g(-1) particle in SRM 1650a and 33.1+/-0.6 micro g g(-1) particle in SRM 2975). Three dinitropyrene isomers were measured in SRM 1975 at 0.5-1.4 micro g g(-1) extract and in SRM 2975 at 1-3 micro g g(-1) particle.     

The identification of nitrated polycyclic aromatic hydrocarbons in diesel particulate extracts and their potential formation as artifacts during particulate collection

Summary The highly complex matrix of diesel particulate extracts was analyzed for nitrated polycyclic aromatic hydrocarbons (nitro-PAH) using fused-silica capillary-column gas chromatography along with a thermionic nitrogen-phosphorus detector (TID) and high-performance liquid chromatography followed by on-line catalytic reduction of the nitro-PAH to amino-PAH and subsequent fluorescence detection. Positive isomer identification and quantitation of nitro-PAH are from retention times of authentic standards and their mass spectra. The ease of nitro-PAH formation by nitration of PAH raises the question regarding the origin of these species, whether they are produced as “native” products during the engine combustion process and/or in the exhaust, or instead, formed as the result of chemical conversion to produce artifacts during the sampling procedure. This problem is assessed examing 1-nitropyrene-concentration in particulates of three light-duty diesel engines for different sampling times. 1-Nitropyrene concentrations show only a moderate increase with sampling time under average sampling conditions. Presented at the 15th International Symposium on Chromatography, Nürnberg, October 1984     

Coupled LC-GC-MS for on-line clean-up,separation, and identification of chlorinated polycyclic aromatic hydrocarbons at picogram levels in urban air

Coupled liquid chromatography – gas chromatography – mass spectrometry (LC-GC-MS) has been applied for on-line clean up, separation, and identification of chlorinated polycyclic aromatic hydrocarbons (CI-PAHs). A loop-type interface was used to couple the liquid chromatograph on-line with the GC-MS, and concurrent solvent evaporation was used for sample transfer. A back-flush technique was used in conjunction with a two-dimensional column system for isolation of CI-PAHs and polycyclic aromatic hydrocarbons (PAHs). This fraction was transferred on-line to the GC and separated on a capillary column. Selective and sensitive detection of CI-PAHs in the GC eluate was obtained by negative ion chemical ionization (NICI) mass spectrometry and selected ion monitoring (SIM). The combined on-line system for isolation, separation, and identification showed high precision and accuracy, and demonstrated a linear response from 1 to 1000 pg for chlorinated PAHs. The estimated detection limit was 250 fg for 1-chloropyrene and 1,6-dichloropyrene. The technique was demonstrated by analysis of urban air samples. The low detection limit made it possible to use the technique for analysis of personally carried monitoring equipment for measurement of exposure to CI-PAHs in the work environment.     

Identification of oxygenated polycyclic aromatic hydrocarbons in diesel particulate matter by capillary gas chromatography and capillary gas chromatography/mass spectrometry

Summary Using a two-step liquid chromatographic separation on normalphase cartridges, crude extracts of diesel particulate matter can be separated without time-consuming sample handling into special fractions which mainly contain slightly-polar oxygenated polycyclic aromatic hydrocarbons (oxy-PAH) and nitrated polycyclic aromatic hydrocarbons (nitro-PAH). Subsequent analysis was by fused-silica capillary gas chromatography on a SE54 column along with flame-ionisation (GC/FID) and positive-ion electron-impact mass spectrometric detection (GC/MS) respectively. A number of individual oxy-PAH belonging to four different chemical classes (ketones, quinones, anhydrides and aldehydes) and several individual nitro-PAH were characterized by their retention times and mass spectra. Presented at the 15th International Symposium on Chromatography, Nürnberg, October 1984     

Optimization of supercritical fluid extraction by carbon dioxide with organic modifiers of polycyclic aromatic hydrocarbons from urban particulate matter

The main advantages of using supercritical fluids for the extractions of organic pollutants from environmental matrix is that they are inexpensive, contaminant free, and less costly to dispose safely than organic solvents. In this work, a series of extraction experiments were carried out using CO2 as supercritical fluid on a certified sample of "Urban dust" (NIST S.R.M. 1649a) to optimize the analytical parameters with the aim of investigating the extraction limit of organic pollutant by using an almost "organic solvent-free" technique. The certified sample contains small concentrations of several organic pollutants, as PAH and PCB. The initial tests of extraction were carried out with only CO2 in supercritical phase, by maintaining the temperature at 50 degrees C and 80 degrees C and by making the pressure vary between 230 bar and 600 bar. The effect of three organic modifiers (methanol, n-hexane and toluene), added at 5% in volume, has been considered. The yield of recovery has been estimated for anthracene, fluoranthene, chrysene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene by GC-MS according to the increasing molecular weight.     

Analysis of polycyclic aromatic hydrocarbons, phenols and aromatic amines in particulate phase cigarette smoke using simultaneous distillation and extraction as a sole sample clean-up step

Polycyclic aromatic hydrocarbons (PAHs), phenols and aromatic amines can be analyzed in particulate phase mainstream cigarette smoke using simultaneous distillation and extraction (SDE) as a unique sample clean-up step. All analytes are determined from the same smoke sample using GC-MS. The smoke from 20 cigarettes is collected on a Cambridge smoke pad where a mixture of internal standards is added. The Cambridge smoke pad is extracted in a SDE apparatus using water-CH2Cl2. The SDE extract is analyzed directly for PAHs, for phenols after silylation, and for amines after derivatization with heptafluorobutyric anhydride. Excellent results in agreement with data reported in the literature are obtained by this procedure.     

Determination of polycyclic aromatic sulfur heterocycles in diesel particulate matter and diesel fuel by gas chromatography with atomic emission detection

The sulfur content of diesel fuel is of environmental concern because sulfur can facilitate the formation of diesel particulate matter (DPM) and sulfur dioxide (SO2) in the exhaust can poison catalytic converters. The US Environmental Protection Agency (EPA) has established more stringent regulations to reduce the sulfur content of diesel fuels in the near future. In this study, various types of organosulfur compounds in DPM extracts and the corresponding fuels have been determined by gas chromatography with atomic emission detection. The diesel fuels used have sulfur contents of 2284 and 433 ppm, respectively, and are labeled as high-sulfur and low-sulfur diesel fuels. The compounds identified are mainly polycyclic aromatic sulfur heterocycles (PASHs). In the fuels tested, trimethylbenzothiophenes (TMBTs), dibenzothiophenes (DBTs), and 4-methyldibenzothiophene (4-MDBT) were the most abundant sulfur compounds, while larger PASH compounds were more abundant in DPM extracts. The high-sulfur diesel fuel contained a larger proportion of PASHs with one or two rings (lighter PASHs). In DPM, the concentrations of total organic sulfur and individual PASHs are higher for the high-sulfur diesel fuel, and the relative percentage of one or two-ring PASHs is higher as well. The influence of engine load on the DPM composition was also examined. With increasing load, the PASH concentration in DPM decreased for lighter PASHs, increased for heavier PASHs, and had a bell-shaped distribution for PASHs in between.     

Optimisation of supercritical fluid extraction of polycyclic aromatic hydrocarbons and their nitrated derivatives adsorbed on highly sorptive diesel particulate matter

Supercritical fluid extraction (SFE) was performed to extract complex mixtures of polycyclic aromatic hydrocarbons (PAHs), nitrated derivatives (nitroPAHs) and heavy n-alkanes from spiked soot particulates that resulted from the incomplete combustion of diesel oils. This polluted material, resulting from combustion in a light diesel engine and collected at high temperature inside the particulate filter placed just after the engine, was particularly resistant to conventional extraction techniques, such as soxhlet extraction, and had an extraction behaviour that differed markedly from certified reference materials (SRM 1650). A factorial experimental design was performed, simultaneously modelling the influence of four SFE experimental factors on the recovery yields, i.e.: the temperature and the pressure of the supercritical fluid, the nature and the percentage of the organic modifier added to CO₂ (chloroform, tetrahydrofuran, methylene chloride), as a means to reach the optimal extraction yields for all the studied target pollutants. The results of modelling showed that the supercritical fluid pressure had to be kept at its maximum level (30 MPa) and the temperature had to be kept relatively low (75 °C). Under these operating conditions, adding 15% of methylene chloride to the CO₂ permitted quantitative extraction of not only light PAHs and their nitrated derivatives, but also heavy n-alkanes from the spiked soots. However, heavy polyaromatics were not quantitatively extracted from the refractory carbonaceous solid surface. As such, original organic modifiers were tested, including pyridine, which, as a strong electron donor cosolvent (15% into CO₂), was the most successful. The addition of diethylamine to pyridine, which enhanced the electron donor character of the cosolvent, even increased the extraction yields of the heaviest PAHs, leading to a quantitative extraction of all PAHs (more than 79%) from the diesel particulate matter, with detection limits ranging from 0.5 to 7.8 ng for 100 mg of spiked material. Concerning the nitrated PAHs, a small addition of acetic acid into pyridine, as cosolvents, gave the best results, leading to fair extraction yields (approximately 60%), with detection limits ranging from 18 to 420 ng.     

Determination of polycyclic aromatic hydrocarbons from ambient air particulate matter using a cold fiber solid phase microextraction gas chromatography-mass spectrometry method

Polycyclic aromatic hydrocarbons (PAH) from ambient air particulate matter (PM) were analyzed by a new method that utilized direct immersion (DI) and cold fiber (CF) SPME-GC/MS. Experimental design was used to optimize the conditions of extraction by DI-CF-SPME with a 100μm polydimethylsiloxane (PDMS) fiber. The optimal conditions included a 5min equilibration at 70°C time in an ultrasonic bath with an extraction time of 60min. The optimized method was validated by the analysis of a NIST standard reference material (SRM), 1649b urban dust. The results obtained were in good agreement with certified values. PAH recoveries for reference materials were between 88 and 98%, with a relative standard deviation ranging from 5 to 17%. Detection limits (LOD) varied from 0.02 to 1.16ng and the quantification limits (LOQ) varied from 0.05 to 3.86ng. The optimized and validated method was applied to the determination of PAH from real particulate matter (PM10) and total suspended particulate (TPS) samples collected on quartz fiber filters with high volume samplers.     

Simultaneous determination of carbonyl compounds and polycyclic aromatic hydrocarbons in atmospheric particulate matter by liquid chromatography-diode array detection-fluorescence detection

Simultaneous analysis of 24 carbonyl compounds (alkanals, unsaturated, dicarbonylic and aromatic aldehydes and ketones) derivatized with 2,4-dinitrophenylhydrazine and 16 polycyclic aromatic hydrocarbons (PAHs) using a photodiode-array (PDA) and a fluorescence (FL) detector in series is proposed.The separation is carried out with a reversed-phase column and gradient elution using four solvents (acetonitrile, water, tetrahydrofuran and methanol) in less than 35 min. Several critical pairs of carbonyl compounds with 3 and 4 carbon atoms and different functional groups, isomers of tolualdehyde, aromatic and aliphatic aldehydes were conditional on the gradient elution. Common pre-treatment for two groups of compounds consists in a step of extraction and derivatization in aqueous medium and a further clean-up using a polymeric phase SPE and concentration in a mixture of dichloromethane:methanol. A pre-concentration factor of 50 was achieved by this procedure. Acetone and formaldehyde blanks were minimized and remain controlled with a specific cleaning of glass material and washing the SPE cartridge.The limits of detection (LOD) ranged from 0.006 to 0.18 ng mL⁻¹ for PAHs and from 2.4 to 10.1 ng mL⁻¹ for carbonyl compounds and method precision was ≤15% for all analysed compounds. Recoveries were within the range of 95-104% for PAHs except for more volatile compounds (acenaphthene and fluorene) and within the range of 72-113% for carbonyl compounds. The method was applied in water-soluble fraction of PM₁₀ (atmospheric particulate matter with an aerodynamic diameter less than 10 μm) and the spectral contrast technique was used in the identification of carbonyl compounds.     

Rapid determination of trace polycyclic aromatic hydrocarbons in particulate matter using accelerated solvent extraction followed by ultra high performance liquid chromatography with fluorescence detection

A method has been developed for the trace analysis of polycyclic aromatic hydrocarbons, which are known as persistent organic pollutants and ubiquitous constituents of fine particulate matter that causes growing airborne pollution. The method, which was especially for samples of airborne particulate matter less than 2.5 μm in diameter, utilized accelerated solvent extraction and ultra high performance liquid chromatography with fluorescence detector. Four principal parameters of accelerated solvent extraction were optimized to obtain maximum extraction efficiency. Using the established synergetic programs of gradient elution and fluorescence wavelength switching, a rapid separation was achieved in 6.56 min with good linearity for 15 polycyclic aromatic hydrocarbons (coefficient of determination above 0.999). The limits of detection ranged from 0.833 to 10.0 pg/m³. The precision of the method expressed as inter‐day relative standard deviation ranged from 0.2 to 1%, which was calculated from nine repetitive measurements of 8.00 μg/L analytes. Average spiked recoveries ranged from 71.6 to 97.7%, with the exception of naphthalene. The rapid, sensitive, and accurate method can meet the pressing needs of health risk assessment and increasingly heavy daily tasks of air quality monitoring.     

Analysis of nitrated polycyclic aromatic hydrocarbons by liquid chromatography with fluorescence and mass spectrometry detection: air particulate matter, soot, and reaction product studies

Polycyclic aromatic hydrocarbons (PAH) and their nitrated derivatives (nitro-PAH) are environmental pollutants which pose a threat to human health even at low concentration levels. In this study, efficient analytical methods for the analysis of nitro-PAH and PAH (extraction, clean-up, chromatographic separation, and spectrometric detection) have been developed, characterized, and applied to aerosol samples. The separation and quantification of 12 nitro-PAH was carried out by reversed-phase high performance liquid chromatography (HPLC), on-line reduction, and fluorescence detection. The detection limits were in the range of 0.03–0.5 g L^–1 (6–100 pg in the investigated sample aliquots), and the recovery rates from soot samples were 70–90%. Nitro-PAH and PAH concentrations have been determined for different types of soot and for urban, rural, and alpine fine air particulate matter (PM2.5). For the first time, trace amounts of nitro-PAH have been detected in a high-alpine clean air environment. The on-line reduction and fluorescence technique has been complemented by atmospheric pressure chemical ionization time-of-flight mass spectrometry (APCI-TOF-MS). The MS detection allowed the analysis of partially nitrated and oxygenated PAH in laboratory studies of the heterogeneous reaction of PAH on soot and glass fiber substrates with gaseous nitrogen oxides and ozone. It led to the tentative identification of a previously unknown nitrated derivative of the particularly toxic PAH benzo[a]pyrene (BaP-nitroquinone), and provides the first experimental evidence that PAH-nitroquinones can be formed by reaction of PAH with atmospheric photooxidants.     

Flocculation-ultrasonic assisted extraction and solid phase clean-up for determination of polycyclic aromatic hydrocarbons in water rich in colloidal particulate with high performance liquid chromatography and ultraviolet-fluorescence detection

In the present work, a simple method of sample preparation for the determination of polycyclic aromatic hydrocarbons (PAHs) in water rich in colloidal particulate was developed. The technique was mainly based on the effect of the flocculation of aluminum sulfate and the adsorption of the flocculation aid florisil. The method contained three steps: flocculation, ultrasonic extraction, and solid-phase extraction cleanup. Major parameters of the procedure were optimized with high performance liquid chromatography (HPLC) separation and ultraviolet-fluorescence detection. When 250 mL model sample containing 16 EPA PAHs was processed, the developed method provided detection limits in the range of 0.02–5 ng/L. Both spiked and non-spiked polluted river water samples rich in suspended particles and organic matters were analyzed. Recoveries and relative standard deviations for the 16 PAHs were in ranges of 86–94% and 3–13% (n = 5), respectively.     

Simultaneous analysis of oxygenated and nitrated polycyclic aromatic hydrocarbons on standard reference material 1649a (urban dust) and on natural ambient air samples by gas chromatography-mass spectrometry with negative ion chemical ionisation

This study deals with the development of a routine analytical method using gas chromatography-mass spectrometry with negative ion chemical ionisation (GC/NICI-MS) for the determination of 17 nitrated polycyclic aromatic hydrocarbons (NPAHs) and 9 oxygenated polycyclic aromatic hydrocarbons (OPAHs) present at low concentrations in the atmosphere. This method includes a liquid chromatography purification procedure on solid-phase extraction (SPE) cartridge. Application of this analytical procedure has been performed on standard reference material (SRM 1649a: urban dust), giving results in good agreement with the few data available in the literature. The analytical method was also applied on ambient air samples (on both gas and particulate phases) from the French POVA program (POllution des Vallées Alpines). NPAHs concentrations observed for a rural site during the Winter period are about 0.2-100.0pgm(-3) in the particulate phase and about 0.0-20.0pgm(-3) in the gas phase. OPAHs present concentrations 10-100 times higher (0.1-2.0ngm(-3) and 0.0-1.4ngm(-3) for the particulate and the gas phases, respectively). These preliminary results show a good correlation between the characteristics of the sampling site and the compound origins (primary or secondary).     

Immunochemical detection of metabolites of parent and nitro polycyclic aromatic hydrocarbons in urine samples from persons occupationally exposed to diesel exhaust

An immunochemical assay was developed for the detection of metabolites excreted in urine as a result of occupational exposure to PAHs and nitro-PAHs. These metabolites were analyzed in a competitive ELISA, using an existing antibody (4D5) that has been developed against 6-aminobenzo[a]pyrene coupled to bovine serum albumine (B[a]P-BSA). A solid phase extraction (SPE) work-up procedure was optimized by dilution of pooled urine samples from rats exposed to 1-NP, in human urine. The application was validated by comparison of test results with urinary excreted 1-hydroxypyrene (1-OH-P) levels in a study among 28 railroad workers. Excretion of urinary metabolites was determined over two consecutive workdays. The 24 h average excretion of metabolites as determined in the immunoassay was not related to levels of particulate matter in the breathing zones of workers, not to 1-OH-P excretion levels of the day of urine collection. However, it was significantly associated with the personal dust exposure of the day before (P<0.0001), suggesting slow excretion of urinary metabolites. Smoking habits caused minor interference (P<0.1).