微波消解-石墨炉原子吸收光谱法测定纸质食品包装材料中的痕量镉

建立了微波消解–石墨炉原子吸收光谱法测定纸质食品包装材料中痕量镉的检验方法。样品经微波消解后,以硝酸镍为基体改进剂,试验确定了石墨炉原子吸收法测定镉的最佳仪器条件。镉的质量浓度在0～10μg/L与吸收峰面积呈良好的线性关系,线性相关系数r=0.9997,检出限为0.025μg/L。将该法用于纸质食品包装材料中痕量镉的测定,并进行加标回收试验,回收率为96.0%～105.5%,相对标准偏差不大于4.4%(n=10)。     

超级微波消解-石墨炉原子吸收光谱法测定不同类型土壤中的镉

采用超级微波消解仪对样品进行前处理,对比不同消解体系的消解效果,选择合适的消解体系,采用石墨炉原子吸收光谱法测定镉浓度,同时优化基体改进剂、灰化温度等工作参数,确定最佳的分析条件。探讨并建立超级微波消解-石墨炉原子吸收光谱法测定不同类型土壤镉含量的方法。在最优条件下,标准曲线在0～1.0μg/L浓度范围内线性关系良好,相关系数r=0.999,检出限浓度为0.04μg/L,定量限浓度为0.12μg/L,方法准确度为94.5%～110%,相对标准偏差RSD为0.60%～5.4%,方法应用于不同类型土壤标准物质镉的测定,测得结果均在标准值范围内。方法简便快捷、准确高效、用酸量低、节约环保,便于在基层推广,适用于批量处理不同类型镉污染土壤样品。     

超级微波消解－石墨炉原子吸收光谱法测定香菇中的镉

为建立一种快速批量检测香菇中镉的方法,建立了超级微波消解－石墨炉原子吸收光谱法测定香菇中镉含量的方法。分别采用湿法消解、普通微波消解和超级微波、传统微波和湿法消解技术前处理香菇标准物质样品,对比消解效果,优化超级微波消解技术的酸体系和消解最终温度。;采用石墨炉原子吸收光谱仪法测定,优化基体改进剂、灰化温度等工作参数,确定仪器最佳检测条件,验证分析方法的准确性和稳定性。结果表明,超级微波消解优于湿法消解和传统微波消解技术,准确性和重复性最佳,大幅减少用酸量的同时更加安全、高效,避免样品污染。在最优分析方法条件下,镉在0~4.0 μg/L范围内所得回归方程线性关系良好,相关系数(R)为0.9994,方法检出限为0.001 mg/kg,精密度RSD为1.4%~2.5%。超级微波消解－石墨炉原子吸收光谱法检测的探索与应用超级微波消解优于湿法消解和传统微波消解技术,大幅减少用酸量的同时更加安全、高效,避免样品污染,为农产品镉含量批量检测提供可靠的方法支撑。     

米面中痕量铍的微波消解-固相萃取/石墨炉原子吸收光谱法分析

建立了微波消解-固相萃取/石墨炉原子吸收法富集并测定米面中痕量铍的方法.采用微波消解制样,7-(2'-胂酸基-5'-羧酸)苯偶氮-8-羟基喹啉-5-磺酸(H2L)与Be2+螯合形成BeL络合物,C18固相萃取柱(C18-SPE)富集BeL,石墨炉原子吸收法测定C18柱洗脱液中的BeL.最佳实验条件为:采用50 μL pH 3.0的50 g/L H2L水溶液与样品中的铍螯合15 min,水相上柱,用2 mL 50%(体积分数)甲醇溶液洗脱.结果表明,方法的线性范围为0.05 ～14 μg/L,检出限为0.02 μg/L,对实际米面样品测定的加标回收率为90% ～110%,可用于食品等复杂基质中痕量铍的测定.     

石墨炉原子吸收法测定土壤中铅、镉、钴、锑、铍

建立石墨炉原子吸收法测定土壤中铅、镉、钴、锑、铍含量的方法。优化了石墨炉原子吸收光谱法测定条件,在最佳实验条件下,采用硝酸-盐酸-氢氟酸-双氧水混合酸体系微波消解土壤样品,选用抗坏血酸-硝酸镁混合溶液为基体改进剂。铅、镉、钴、锑、铍的质量浓度在各自的范围内与吸光度成良好的线性关系,相关系数均大于0.999,各元素的检出限为0.008~0.06 μg/g。样品加标回收率为90.5%~104.0%,测定结果的相对标准偏差均小于2.5%(n=6)。该方法样品前处理简便,灵敏度高,检出限低,测定结果准确、可靠,可用于土壤中铅、镉、钴、锑、铍的测定。     

石墨炉原子吸收光谱法测定麦麸颗粒中镉

为消除石墨炉原子吸收光谱法测定麦麸中镉时基体产生的背景干扰,在消解液中加入镉标准溶液配制基体匹配工作曲线进行测定,对灰化温度、原子化温度及基体改进剂等条件进行优化,确定最佳分析方法。结果表明：在选定条件下镉在0.0~3.0 μg/L范围内工作曲线相关系数为0.9991,检出限为0.027 μg/L,定量限为0.091 μg/L,加标回收率为89.50%~104.12%,精密度为1.64%~4.30%,质控物质测定结果准确。该方法操作简便,快速准确,精密度良好,适用于麦麸中镉元素的测定。     

微波消解-石墨炉原子吸收光谱法测定污水厂污泥和进、出水中的镉、铅

建立了微波消解–石墨炉原子吸收光谱法测定污水处理厂进出水和污泥中重金属Cd,Pb的方法。分别向污水样品中加入5.0 mL硝酸,污泥样品中加入4.0 mL硝酸和2.0 mL双氧水,放入微波消解炉中进行消解。消解好的样品用1%NH_4H_2PO_4作为基体改进剂,在0.5%HNO_3介质中采用塞曼扣除背景,石墨炉程序升温方式进行Cd,Pb的原子化,用石墨炉原子吸收光谱法测定Cd,Pb的含量。Cd,Pb的质量浓度分别在0~2.00μg/L,0~40.0μg/L范围内与其吸收峰高呈良好的线性关系,线性相关系数分别为0.999 1,0.999 6。Cd,Pb检出限分别为0.104 9,0.394 5μg/L,测定结果的相对标准偏差分别为1.34%~3.61%,2.12%~2.80%(n=11),加标回收率分别为98.2%~102.6%,94.0%~100.4%。该方法简单,高效,结果准确度高,重现性好,适用于污水处理厂的进出水和污泥中重金属铅和镉的检测。     

微波消解–石墨炉原子吸收法测定药食两用中药材中的铅

建立测定药食两用中药材中铅含量的微波消解–石墨炉原子吸收光谱分析方法。样品经微波消解后,以2%磷酸二氢铵为基体改进剂,用石墨炉原子吸收法测定药食两用中药材中的铅含量。在2~40μg/L范围内,铅的质量浓度与吸光度呈良好的线性关系,线性相关系数r大于0.999,检出限为5μg/kg。加标回收率为94.0%~105.5%,测定结果的相对标准偏差小于5.0%(n=6)。该方法操作简便快速,准确度较高,基体干扰小,适合药食两用中药材中铅的检测。     

微波消解石墨炉原子吸收光谱法测定氢化棉籽油中痕量镍

建立了微波消解样品、塞曼扣背景石墨炉原子吸收测定氢化棉籽油中痕量镍的方法。向0.050 0 g氢化棉籽油样品中加入2 m L的硝酸和0.5 m L双氧水,于微波消解仪中消解,用石墨炉原子吸收法测定样品溶液中镍的含量。镍的含量在0.1~50 ng/m L范围内与其吸光度呈良好的线性关系,线性相关系数为0.998 2,检出限为15pg/m L。测定结果的相对标准偏差为2.33%(n=11),样品加标回收率为94%~102%,该方法的测定结果与美国药典法基本一致。该方法样品处理方法快速、简单,背景空白低,测定结果准确、可靠,适合于实际样品分析。     

微波消解-石墨炉原子吸收光谱法分析测定食用菌中总砷

摘 要：采用微波消解-石墨炉原子吸收光谱法分析测定食用菌中总砷。取可食部分的食用菌粉碎均匀,采用微波消解对样品进行消解,将消解液于140℃赶酸至0.5mL ,用超纯水转移定容至25mL。以0.1%的硝酸钯为基体改进剂,塞曼扣背景,用石墨炉原子吸收光谱法测定总砷。方法检出限为0.4μg/L,线性范围为0~30 μg/L,线性相关系数(r)大于0.998,采用精密度考察方法重现性,不同浓度水平的RSD%均小于6.6%;三个浓度水平的加标回收率为80.6% ~ 103.9%,有证标准物质测定结果符合要求。实验结果表明,方法操作简便、灵敏、准确,适合食用菌中总砷的测定。对砷形态复杂的野生食用菌,微波消解后可直接采用石墨炉原子吸收光谱法测定总砷。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.