Polymers for tissue engineering,medical devices,and regenerative medicine. Concise general review of recent studies

Recently investigated applications of polymeric materials for tissue engineering, regenerative medicine, implants, stents, and medical devices are described in the present review. Papers published during the last 2 years about polymeric materials used for preparation of various polymeric scaffolds, methods of fabrication of such scaffolds and their effectiveness in providing support for cell growth and development into various tissues and enhancing or mimicking an extracellular network (ECM's) have been cited. Papers describing the use of such polymeric materials for tissue engineering of cartilage and bones were cited. The exciting developments in the field of regenerative medicine, based on application of the self‐assembled biocompatible polymeric scaffolds for regeneration of tissues and organs are described in some detail. The use of the biocompatible and biodegradable collapsible polymeric stents, as well as the use of biocompatible, but not necessarily biodegradable polymeric materials for protective coatings of metallic stents and reservoirs of drugs, preventing restenosis and other post‐operative complications that may occur after insertion of a stent, have been reviewed. Clinical results pointing out the advantages of such treatments, as well as results indicating their limitations, have been cited. New formulas, for coating implants, stents, and other medical devices, have been discussed. Copyright © 2006 John Wiley & Sons, Ltd.     

Chemico-physical characterisation and in vivo biocompatibility assessment of DLC-coated coronary stents

The vast majority of stent thrombosis occurs in the acute and sub-acute phases and is more common in patients with acute coronary syndromes, due to the thrombotic milieu where stent struts are positioned. Stent thrombosis is likely due to incomplete tissue coverage of metallic stents as the contact between metallic stents and blood elements may lead to platelet adhesion and trigger vessel thrombosis. If a stent is covered after 7 days, the risk that it will be found uncovered at later stages is very low (<1 %). In this article, we demonstrate that diamond-like carbon (DLC) coatings, deposited by physical vapour deposition, promote rapid endothelisation of coronary stent devices, with very low platelets activation, reducing thrombotic clots. We relate these behaviours to the surface and bulk material properties of the DLC films, subjected to a comprehensive chemico-physical characterisation using several techniques (X-ray photoelectron spectroscopy, atomic force microscopy, field-emission scanning electron microscope, transmission electron microscopy combined with electron energy loss spectroscopy, Raman and dispersive X-ray spectroscopy). In vivo studies, conducted on 24 pigs, have shown complete endothelisation after 7 days, with no fibrin mesh and with only rare monocytes scattered on the endothelial layer while 30 and 180 days tests have shown reduced inflammatory activation and a complete stabilisation of the vessel healing, with a minimal neointimal proliferation. The integral and permanent DLC film coating improves haemo- and bio-compatibility and leads to an excellent early vessel healing of the stent whilst the extremely thin strut thickness reduces the amount of late neointima and consequently the risk of late restenosis. These data should translate into a reduced acute and sub-acute stent thrombosis.

Thermoresponsive conductive polymer composite thin film and fiber mat: Crosslinked PEDOT:PSS and P(NIPAAm‐co‐NMA) composite

The thermoresponsive conductive composite (TCC) thin films and fiber mats, whose electrical property changed with temperature, were fabricated successfully. The thermocrosslinkable and thermoresponsive copolymer, poly(N‐isopropyl acrylamide‐co‐N‐methylolacrylamide) (PNN), was synthesized. The TCC thin film and fiber mat were fabricated by spin coating and electrospinning process of PEDOT:PSS/PNN solutions, respectively. After thermocrosslinking and doping by DMSO, the composite thin films and fiber mats were obtained. Fibrous structures of TCC fiber mats were observed by SEM. The surface resistance and conductivity of composites were measured. The thermoresponsivity and swelling ratio of TCCs were also studied. The thermoresponsive conductive property was analyzed by measuring the surface resistance of TCCs in water bath under various temperatures from 20 to 50 °C. With the increase of temperature, the TCCs shrank to be dense structure and showed lower surface resistance. The TCC fibers mat exhibited greater sensitivity to temperature than thin film owing to its fibrous structure. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1078–1087     

Aligned and molecularly oriented semihollow ultrafine polymer fiber yarns by a facile method

In this work, aligned and molecularly oriented bone‐like PLLA semihollow fiber yarns were manufactured continuously from an optimized homogeneous polymer‐solvent‐nonsolvent system [PLLA, CH₂Cl₂, and dimethyl formamide (DMF)] by a single capillary electrospinning via self‐bundling technique. Here, it should be emphasized that the self‐bundling electrospinning technique, a very facile electrospinning technique with a grounded needle (which is to induce the self‐bundling of polymer nanofibers at the beginning of electrospinning process), is used for the alignment and molecular orientation of the polymer fiber, and the take‐up speed of the rotating drum for the electrospun fiber yarn collection is very low (0.5 m/s). PLLA can be dissolved in DMF and CH₂Cl₂ mixed solvent with different ratios. By varying the ratios of mixed solvent system, PLLA electrospun semihollow fiber with the porous inner structure and compact shell wall could be formed, the thickness of the shell and the size of inner pores could be adjusted. The results of polarized FTIR and wide angle X‐ray diffraction investigations verified that as‐prepared PLLA semihollow fiber yarns were well‐aligned and molecularly oriented. Both the formation mechanism of semihollow fibers with core‐shell structure and the orientation mechanism of polymer chains within the polymer fibers were all discussed. The as‐prepared self‐bundling electrospun PLLA fiber yarns possessed enhanced mechanical performance compared with the corresponding conventional electrospun PLLA fibrous nonwoven membranes. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1118–1125, 2010     

Poly(polyol sebacate) Elastomers as Coatings for Metallic Coronary Stents

Biocompatible polymeric coatings for metallic stents are desired, as currently used materials present limitations such as deformation during degradation and exponential loss of mechanical properties after implantation. These concerns, together with the present risks of the drug‐eluting stents, namely, thrombosis and restenosis, require new materials to be studied. For this purpose, novel poly(polyol sebacate)‐derived polymers are investigated as coatings for metallic stents. All pre‐polymers reveal a low molecular weight between 3000 and 18 000 g mol^?1. The cured polymers range from flexible to more rigid, with E‐modulus between 0.6 and 3.8 MPa. Their advantages include straightforward synthesis, biodegradability, easy processing through different scaffolding techniques, and easy transfer to industrial production. Furthermore, electrospraying and dip‐coating procedures are used as proof‐of‐concept to create coatings on metallic stents. Biocompatibility tests using adipose stem cells lead to promising results for the use of these materials as coatings for metallic coronary stents.

     

Mesostructured cellular foam solid‐phase microextraction coating for the highly sensitive recognition of polychlorinated biphenyls in water samples

We herein presented a mesoporous cellular foam solid‐phase microextraction coating that showed highly sensitive recognition for weakly polarity polychlorinated biphenyls in water samples. The mesoporous cellular foam coater fiber was for the first time prepared by a simple sol‐gel method. The main experimental parameters including extraction temperature, extraction time, desorption time, stirring rate, and ionic strength were investigated by high‐efficiency orthogonal array design, a L₁₆ (4⁴) matrix was applied for the identification of optimized extraction parameters, and the optimized method was successfully applied to the analysis of environmental water sample. The novel mesoporous cellular foam coated fibers exhibited sensitive limits of detection (0.07–0.28 µg/L), wide linearity (5–3000 µg/L), and good reproducibility (3.5–8.3% for single fiber, and 4.9–8.7% for fiber‐to‐fiber) for polychlorinated biphenyls. The home‐made coating was successfully used in the analysis of polychlorinated biphenyls in real environmental water samples. These results indicate that the synthesized mesoporous cellular foams are promising materials for adsorption and separation applications in sample pretreatment.     

Preparation and application of molecularly imprinted polymer solid‐phase microextraction fiber for the selective analysis of auxins in tobacco

As signal molecules, auxins play an important role in mediating plant growth. Due to serious interfering substances in plants, it is difficult to accurately detect auxins with traditional solid‐phase extraction methods. To improve the selectivity of sample pretreatment, a novel molecularly imprinted polymer ‐coated solid‐phase microextraction fiber, which could be coupled directly to high‐performance liquid chromatography, was prepared with indole acetic acid as template molecule for the selective extraction of auxins. The factors influencing the polymer formation, such as polymerization solvent, cross‐linker, and polymerization time, were investigated in detail to enhance the performance of indole acetic acid‐molecularly imprinted polymer coating. The morphological and chemical stability of this molecularly imprinted polymer‐coated fiber was characterized by scanning electron microscopy, infrared spectrometry, and thermal analysis. The extraction capacity of the molecularly imprinted polymer‐coated solid‐phase microextraction fiber was evaluated for the selective extraction of indole acetic acid and indole‐3‐pyruvic acid followed by high‐performance liquid chromatography analysis. The linear range for indole acetic acid and indole‐3‐pyruvic acid was 1–100 µg/L and their detection limit was 0.5 µg/L. The method was applied to the simultaneous determination of two auxins in two kinds of tobacco (Nicotiana tabacum L and Nicotiana rustica L) samples, with recoveries range from 82.1 to 120.6%.     

Polyisobutylene‐paclitaxel conjugates with pendant carboxylic acids and polystyrene chains: Towards multifunctional stent coatings with slow drug release

Drug‐eluting stents are used in the treatment of atherosclerosis, where the incorporation of anti‐proliferative or anti‐inflammatory drugs decreases the rate of restenosis, the recurrence of artery narrowing. However, these stents can suffer from limitations such as drug depletion and delamination of the drug‐eluting coating from the stent surface. Described here is an approach aimed at addressing these issues. Starting from a maleic anhydride adduct of polyisobutylene (PIB) prepared from butyl rubber, ring opening using paclitaxel (PTX) or a combination of PTX and polystyrene (PS) afforded covalent conjugates of PTX and PIB or PIB‐PS graft copolymers bearing pendant carboxylic acids. When coated on stainless steel, the drug release was slower than that from a control coating that ressembles a clinical formulation comprising a physical mixture of a PS‐PIB‐PS triblock copolymer (SIBS) and PTX. The PTX conjugates also exhibited enhanced adhesion to stainless steel and increased tensile strength in comparison with the starting rubber. Cytotoxicity assays indicated that the materials did not leach toxic levels of PTX into cell culture media. Nevertheless, they were capable of inhibiting the adhesion and proliferation of C2C12 cells on their surfaces. These properties are advantageous for the potential application of the materials as stent coatings. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2209–2219     

Improved blood compatibility of rapamycin-eluting stent by incorporating curcumin

This paper dealt with improving the blood compatibility of the rapamycin-eluting stent by incorporating curcumin. The rapamycin- and rapamycin/curcumin-loaded PLGA (poly(d,l-lactic acid-co-glycolic acid)) coatings were fabricated onto the surface of the stainless steel stents using an ultrasonic atomization spray method. The structure of the coating films was characterized by Fourier transform infrared spectroscopy (FTIR). The optical microscopy and scanning electron microscopy (SEM) images of the drug-eluting stents indicated that the surface of all drug-eluting stents was very smooth and uniform, and there were not webbings and "bridges" between struts. There were not any cracks and delaminations on stent surface after expanded by the angioplasty balloon. The in vitro platelet adhesion and activation were investigated by static platelet adhesion test and GMP140 (P-selection), respectively. The clotting time was examined by activated partially prothromplastin time (APTT) test. The fibrinogen adsorption on the drug-loaded PLGA films was evaluated by enzyme-linked immunosorbent assay (ELISA). All obtained data showed that incorporating curcumin in rapamycin-loaded PLGA coating can significantly decrease platelet adhesion and activation, prolong APTT clotting time as well as decrease the fibrinogen adsorption. All results indicated that incorporating curcumin in rapamycin-eluting coating obviously improve the blood compatibility of rapamycin-eluting stents. It was suggested that it may be possible to develop a drug-eluting stent which had the characteristics of not only good anti-proliferation but also improved anticoagulation.     

Preparation and application of a coated‐fiber needle extraction device

In this study, a needle‐trap device with fibers coated with a molecularly imprinted polymer was developed for separation. A number of heat‐resistant Zylon filaments were longitudinally packed into a glass capillary, followed by coating with a molecularly imprinted polymer. Then, the molecularly imprinted polymer coating was copolymerized and anchored onto the surface of the fibers. The bundle of synthetic fibers coated with the molecularly imprinted polymer was packed into a 21G stainless‐steel needle and served as an extraction medium. The coated‐fiber needle extraction device was used to extract volatile organic compounds from paints and gasoline effectively. Subsequently, the extracted volatile organic compounds were analyzed by gas chromatography. Calibration curves of gaseous benzene, toluene, ethylbenzene, and o‐xylene in the concentration range of 1–250 μg/L were obtained to evaluate the method, acceptable linearity was attended with correlation coefficients above 0.998. The limit of detection of benzene, toluene, ethylbenzene, and o‐xylene was 11–20 ng/L using the coated‐fiber needle‐trap device. The relative standard deviation of needle‐to‐needle repeatability was less than 8% with an extraction time of 20 min. The loss rates after storage for 3 and 7 days at room temperature were less than 30%.     

Preparation of hydrophilic molecularly imprinted solid‐phase microextraction fiber for the selective removal and extraction of trace tetracyclines residues in animal derived foods

The present work reported a novel hydrophilic and selective solid‐phase microextraction fiber by improved multiple co‐polymerization method immobilization of tetracycline molecularly imprinted polymer on a stainless steel wire and directly coupled with high‐performance liquid chromatography for sensitive determination of trace tetracyclines residues in animal derived foods. The developed molecularly imprinted polymer coated solid‐phase microextraction fibers were characterized through scanning electron microscopy, Fourier transfer infrared spectroscopy, thermogravimetric analysis, and adsorption experiments, the fiber with cross‐linked and porous structure was observed and high thermal and chemical stability. The maximum adsorption capacity of this fiber with good selectivity reached 2.35 µg/mg in aqueous matrices, and showed good repeatability (relative standard deviation ≤ 6.6%, n = 5) and satisfying reproducibility between fiber to fiber (relative standard deviation ≤ 7.8%, n = 5). Under the optimized solid‐phase microextraction conditions, satisfactory linearity (5–1000 µg/L) and detection limits (0.38–0.72 µg/kg, S/N = 3) for all the tetracyclines were obtained. The practicality of this method was proved by adding tetracycline, oxytetracycline at three levels to milk, chicken, and fish samples with good recoveries of 77.3–104.4%.     

Facile deposition of high quality ferroelectric poly(vinylidene fluoride) thin films by thermally modulated spin coating

Direct deposition of high quality ferroelectric PVDF thin films using a modulated temperature spin coating method is demonstrated. The method is qualitatively guided from Flory‐Huggins theory of polymeric solutions and is general in applicability. Ferroelectric PVDF films with similar high structural and dielectric quality are deposited in environments ranging from 20 to 80% relative humidity on polar and non‐polar surfaces. The films do not show the presence of the non‐ferroelectric α‐phase. Resultant films have rms roughness values lower than 16 nm and remnant polarizations up to 6.5 µC cm^?2. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 221–227     

Development of a Polymer‐Based Biodegradable Neurovascular Stent Prototype: A Preliminary In Vitro and In Vivo Study

Biodegradable stents are not established in neurovascular interventions. In this study, mechanical, radiological, and histological characteristics of a stent prototype developed for neurovascular use are presented. The elasticity and brittleness of PLA 96/4, PLDL 70/30, PCL, and PLGA 85/15 and 10/90 polymers in in vitro experiments are first analyzed. After excluding the inapt polymers, degradability and mechanical characteristics of 78 PLGA 85/15 and PLGA 10/90 stent prototypes are analyzed. After excluding PLGA 10/90 stents because of rapid loss of mass PLGA 85/15 stents in porcine in vivo experiments are analyzed. Angiographic occlusion rates 7 d, 1 month, 3 months, and 6 months after stent implantation are assessed. Histological outcome measures are the presence of signs of inflammation, endothelialization, and the homogeneity of degradation after six months. One case of stent occlusion occurs within the first 7 d. There is a prominent foreign‐body reaction with considerable mononuclear and minor granulocytic inflammation combined with incomplete fragmental degradation of the struts. It is possible to produce a stent prototype with dimensions that fit the typical size of carotid arteries. Major improvements concerning thrombogenicity, degradation, and inflammatory response are required to produce biodegradable stents that are suitable for neurovascular interventions.     

A Strategy for Rapid Construction of Blood Vessel‐Like Structures with Complex Cell Alignments

A method is developed that can rapidly produce blood vessel‐like structures by bonding cell‐laden electrospinning (ES) films layer by layer using fibrin glue within 90 min. This strategy allows control of cell type, cell orientation, and material composition in separate layers. Furthermore, ES films with thicker fibers (polylactic‐co‐glycolic acid, fiber diameter: ≈3.7 µm) are used as cell‐seeding layers to facilitate the cell in‐growth; those with thinner fibers (polylactic acid, fiber diameter: ≈1.8 µm) are used as outer reinforcing layers to improve the mechanical strength and reduce the liquid leakage of the scaffold. Cells grow, proliferate, and migrate well in the multilayered structure. This design aims at a new type of blood vessel substitute with flexible control of parameters and implementation of functions.     

Preparation of polybenzoxazole fibers via electrospinning and postspun thermal cyclization of polyhydroxyamide

Polybenzoxazole (PBO) fibers with a submicron diameter were successfully prepared by electrospinning its precursor, polyhydroxyamide (PHA), solutions to obtain the PHA fibers first, followed by appropriate thermal treatments for cyclization reaction. BisAPAF‐IC PHA with two different molecular weights (MWs) were synthesized from a low temperature polymerization of 2,2′‐bis(3‐amino‐4‐hydroxyphenyl) hexafluoropropane (BisAPAF) and isophthaloyl chloride (IC). Using dimethylacetamide (DMAc) and tetrahydrofuran (THF), solvent effects on the electrospinnability of PHA solutions were investigated. For balancing the solution properties, it was found that DMAc/THF mixture with a weight ratio of 1/9 was the best cosolvent to prepare smooth PHA fibers; uniform PHA fibers with a diameter of 325–720 nm were obtained by using 20 wt % PHA/(DMAc/THF) solutions. For a fixed PHA concentration, solutions with a lower MW of PHA yielded thinner electrospun fibers under the same electrospinning condition. After obtaining the electrospun BisAPAF‐IC PHA fibers, subsequent thermal cyclization up to 350 °C produced the corresponding thermally stable BisAPAF‐IC PBO fibers with a diameter of 305–645 nm. The structure of the precursor fibers and the fully cyclized fibers were characterized by FTIR. For the cyclized BisAPAF‐IC PBO fibers, thermogravimetric analysis showed a 5% weight loss temperature at 523 °C in nitrogen atmosphere. The interconnected fiber structure in the BisAPAF‐IC PBO fiber mats was irrelevant to the curing process, but resulted from the jet merging during the whipping process as revealed by the high speed camera images. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8159–8169, 2008     

A highly thermal-resistant electrospun-based polyetherimide nanofibers coating for solid-phase microextraction

A high-temperature-resistant solid-phase microextraction (SPME) fiber was prepared based on polyetherimide (PEI) by the electrospinning method. The PEI polymeric solution was converted to nanofibers using high voltages and directly coated on a stainless steel SPME needle. The scanning electron microscopy images of PEI coating showed fibers with diameter range of 500–650 nm with a homogeneous and smooth surface morphology. The SPME nanofibers coating was optimized for PEI percentage, electrospinning voltage, and time. The extraction efficiency of the coating was investigated for headspace SPME of some environmentally important polycyclic aromatic hydrocarbons from aqueous samples followed by gas chromatography–mass spectrometry measurement. In addition, the important extraction parameters including extraction temperature, extraction time, ionic strength, as well as desorption temperature and time were investigated and optimized. The detection limits of the method under optimized conditions ranged from 1 to 5 ng L^?1 using time-scheduled selected ion monitoring mode. The relative standard deviations of the method were between 1.1 and 7.1 %, at a concentration level of 500 ng L^?1. The calibration curves of polycyclic aromatic hydrocarbons showed linearity in the range of 5–1000 ng L^?1. The developed method was successfully applied to real water samples and the relative recovery percentages obtained from the spiked water samples were from 84 to 98 % for all the selected analytes except for acenaphthene which was from 75 to 106 %.     

Hydrophobic waterborne coating for cellulose containing hybrid organic nanoparticle pigments with vegetable oils

Vegetable oils were combined with recent nanotechnology as a sustainable method for tuning the hydrophobicity of cellulose and paper surfaces. Different soy-, sunflower-, corn-, castor-, rapeseed- and hydrogenated oils were incorporated into an aqueous dispersion of hybrid styrene maleimide nanoparticles. Here, we investigate the formation of novel coatings from these dispersions and their performance on paper and paperboard, compared with model aluminum substrates. The coated papers are evaluated by static and dynamic contact angles, microscopy, atomic force microscopy, infrared and Raman spectroscopy. The nanoparticle pigments form a porous coating after drying, while the water repellence and hydrophobicity of paperboard and paper improved with contact angles of 90–99° after drying and 98–112° after ageing. The coatings with poly(unsaturated) oils have best hydrophobicity for dispersions with an optimum viscosity of 115–150 cp required for good coverage of the paper. While homogeneous coverage of the cellulose fibers is a primary requirement, thin coatings often provide higher contact angles on paper due to roughness of the underlaying fibrous surface. After ageing, the coatings are chemically stable without oil leakage and constant imide content, while an increase in contact angles is attributed to variations in coating morphology through local re-arrangements over the paper substrate.     

Comparison of Gelatin/Polylysine- and Silk Fibroin/SDF-1α-Coated Mesenchymal Stem Cell-Seeded Intracranial Stents

Endothelialization of the aneurysmal neck is essential for aneurysm healing after endovascular treatment. Mesenchymal stem cell (MSC)-seeded stents can promote aneurysm repair. The biological effects of coated and uncoated nitinol intracranial stents seeded with MSCs on vascular cells and macrophage proliferation and inflammation are investigated. Two stent coatings that exert pro-aggregation effects on MSCs via different mechanisms are examined: gelatin/polylysine (G/PLL), which enhances cell adhesion, and silk fibroin/SDF-1α (SF/SDF-1α), which enhances chemotaxis. The aim is to explore the feasibility of MSC-seeded coated stents in the treatment of intracranial aneurysms. The G/PLL coating provides the highest cytocompatibility and blood compatibility substrate for MSCs and vascular cells and promotes cell adhesion and proliferation. Moreover, it enhances MSC secretion and regulation of vascular cell and macrophage proliferation and chemotaxis. Although the SF/SDF-1α coating promotes MSC secretion and vascular cell chemotaxis, it induces a greater degree of macrophage proliferation, chemotaxis, and secretion of pro-inflammatory factors. MSC-seeded stents coated with G/PLL may benefit stent surface endothelialization and reduce the inflammatory response after endovascular treatment of intracranial aneurysm. These effects may improve aneurysm healing and increase the cure rate.     

Stretch‐Induced Drug Delivery from Superhydrophobic Polymer Composites: Use of Crack Propagation Failure Modes for Controlling Release Rates

The concept of using crack propagation in polymeric materials to control drug release and its first demonstration are reported. The composite drug delivery system consists of highly‐textured superhydrophobic electrosprayed microparticle coatings, composed of biodegradable and biocompatible polymers poly(caprolactone) and poly(glycerol monostearate carbonate‐co‐caprolactone), and a cellulose/polyester core. The release of entrapped agents is controlled by the magnitude of applied strain, resulting in a graded response from water infiltration through the propagating patterned cracks in the coating. Strain‐dependent delivery of the anticancer agents cisplatin and 7‐ethyl‐10‐hydroxycamptothecin to esophageal cancer cells (OE33) in vitro is observed. Finally the device is integrated with an esophageal stent to demonstrate delivery of fluorescein diacetate, using applied tension, to an ex vivo esophagus.     

Microfluidic channels fabricated on mesoporous electrospun fiber mats: A facile route to microfluidic chips

We report a facile way of preparing microfluidic channels filled with electrospun functional fibers. Patterned elastic molds were in tight contact with electrospun fiber mats without any leak of the analyte solution. As an example of the simple devices, we demonstrated a microfluidic protein chip selectively purifying histidine‐tagged proteins. Highly mesoporous nitrilotriacetic acid‐functionalized polystyrene (PS‐NTA) fibers were produced by taking advantage of interpenetrating phase separation between PS and PEO during electrospinning. The specific interaction of Ni‐complexed PS‐NTA fibers with histidine enabled us to immobilize only target proteins from highly heterogeneous protein mixtures. The easy process to fabricate functionalized microchannels combined with the high production throughput from electrospinning may greatly contribute to chip‐based chromatographic and bioanalytical devices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011