Effect of anodic potential on process of formation of polyporphyrin film in solutions of tetrakis(p-aminophenyl)porphin in dichloromethane

The electrode impedance spectroscopy technique was used to study the process of formation of a conducting polyporphyrin film on a Pt electrode from a 10^?3 M solution of tetrakis(p-aminophenyl)porphin in dichloromethane. An equivalent circuit is suggested for simulation of interface impedance in a wide range of working electrode potentials. It is shown that regions with a different mechanism of film formation are observed at an increase in potential from 0.0 to +1.0 V. The kinetics of film formation are studied at the potentials of +0.40, +0.60, and +0.80 V. It is found that good agreement is observed between the model and experimental data when the growing film is simulated using a Warburg element with a finite diffusion length. Conductivity and the diffusion coefficient of charge carriers in it are estimated on the basis of the suggested model for a film obtained at the potential of +0.40 V. It is shown that conductivity of a polyporphyrin film grows by more than an order of magnitude at an increase in deposition potential from +0.40 to +0.80 V.     

Role of acidity on the electrochemistry of Prussian Blue at plain and Nation filmcoated electrodes

Prussian Blue (PB) coated on plain platinum (Pt) shows a redox wave at 0.44V vs SCE in addition to the two usual redox waves at 0.82 and 0.12 V vs SCE when the electrodes were dipped in acidic KC1 solution. PB incorporated into Nation film-coated on Pt electrode exhibited the same behaviour even in the presence of neutral KG solution. In acidic KC1, the additional redox wave observed for PB incorporated into Nation film shifted positively to 0.39V vs SCE and the peak separation was reduced to 30mV. The observed additional redox wave for PB coated on plain Pt electrode and incorporated into Nafion film-coated Pt electrodes was assigned to the partial reduction of PB occurring due to the insertion of protons into the film. The effect of various cations on the electrochemistry of PB incorporated into Nafion film-coated electrode was also studied.     

Influence of electrodeposition conditions on the properties of CdTe films

The results of the influence of electrodeposition conditions on the structural, compositional, optical, and photoelectrochemical properties of CdTe thin films deposited in one-step electrochemical method are presented. The CdTe films were prepared electrochemically from aqueous acidic solution with low ratios of Cd²⁺ ions to Te(IV) ions concentration. Instead of commonly used TeO₂, water-soluble Na₂TeO₃ was used as a source of tellurium ions. The cathodic deposition of CdTe was performed at different constant potentials from solutions containing different cadmium and tellurium ions concentration. As-deposited CdTe thin films were studied by different analytical techniques. The X-ray photoelectron spectroscopy spectra exhibited CdTe formation on the electrode with some amount of tellurium oxides and cadmium oxides. The best quality CdTe deposits, free of TeO₂, were formed in bath containing excess of Cd²⁺ ions and at the potential of ?0.65 V vs. saturated calomel electrode, slightly more positive than E _eq of Cd/Cd²⁺ system. Structural X-ray diffraction studies revealed polycrystallinity of deposits with the highest content of the (111)-oriented cubic (111) form. Optical band gap energy values were found in the range from 1.36 to 1.6 eV for CdTe films prepared at various synthesis conditions. The preliminary photoelectrochemical studies have shown that the variation of the deposition potential as well as bath composition leads to the formation of p- or n-type CdTe films. As-deposited CdTe films were not stable in polysulfide solution under illumination.     

Electrochemical and in situ Raman spectroscopic study on the stability of poly(<Emphasis Type="Italic">N</Emphasis>-methylaniline)

The stability of poly(N-methylaniline) (PNMA) as electrode material has been studied in aqueous solutions of sulfuric acid with the use of electrochemical and in situ Raman spectroscopic techniques. It has been shown that the electrochemical decomposition of electrodeposited PNMA films follows a first-order reaction kinetics. The decomposition rate constants vary between 1.2 × 10⁻⁵ and 2.0 × 10⁻³ s⁻¹ for electrode potential varying between 0.2 and 1.0 V vs Ag/AgCl, respectively. In situ Raman spectroscopy has been applied in obtaining kinetic data at selected electrode potentials, and good correlation of these data with the corresponding data obtained by cyclic voltammetry has been found. As compared to polyaniline, the decomposition of PNMA proceeds at nearly the same rate at electrode potentials not exceeding 0.5 V. The decomposition of PNMA proceeds faster within the potential limits of 0.5 to 0.8 V and slower at electrode potentials exceeding 0.8 V as compared to polyaniline. This article is dedicated to Professor Algirdas Vaškelis (Institute of Chemistry, Vilnius, Lithuania) on the occasion of his 70th birthday and in honour of his contributions to electrochemistry and physical chemistry.     

The formation and reduction of anodic films on electrodeposited ruthenium

The formation and reduction of anodic films on bright ruthenium was investigated using substrates prepared by electrodeposition onto gold-plated platinum from a commercial ruthenium bath operated at 70°C. Anodic films formed on the ruthenium may be reduced by maintaining the electrode at potentials below 0.2 V. The reduction behaviour was markedly affected by the anodization potential and, at short times, by the period of anodization. The bell-shaped cathodic current-time curves observed with films produced at potentials in the region of 1.2 V, suggest that the process in this case involves nucleation of reduction centres on a relatively stable surface layer. The influence of potential, time, and both the concentration and nature of the electrolyte on the extent of anodic film formation was investigated. The results are discussed in terms of the formation of stable phase oxides in the relatively thick anodic film produced on the ruthenium surface.     

Electrodeposition of Copper Selenide onto Mo Electrode in Tartaric Acid Solution

Results are presented of a study of the electrochemical behavior of copper(II) and selenium(IV) ions and their joint reduction on a molybdenum electrode by cyclic voltammetry in a tartaric acid electrolyte. The potentiostatic deposition was used to obtain copper selenide deposits on Mo plates. The diffraction and energydispersive analyses demonstrated that a Cu_2?xSe compound is formed with an admixture of the CuSe phase. A suggestion is made that the process of underpotential reduction affects the formation of copper selenide. Copper selenide films were deposited at a potential of ?0.6 V in the course of 30 min with a thickness of 0.43 μm and high adhesion to the substrate. At potentials in this range, an additional amount of the deposit may be formed due to the chemical reaction between Cu⁺ and Se^2? ions. The p-type conduction was determined for films electrodeposited at various potentials.     

CdSe电沉积层的组成及形成机理

伏安曲线和现场光电流测定用于研究在钛基体上阴极电沉积形成Cdse薄膜的机理. XPS实验表明, CdSe沉积层的组成与沉积电位、沉积时间和溶液组成有关.在0.1 mol·L~(-1)CdSO_4+4 mmol·L~(-1)H_2SeO_3+0.2 mol·L~(-1) H_2SO_4溶液中, 当电位比-0.50 V正时生成富Se层, 而当电位比-0.70 V还负时生成富Cd层. 在-0.69 V下沉积, 沉积层的Se/Cd计量比接近1.1. 在同一电位下, 若提高H_2Se0_3浓度, 则沉积物中Se的含量增多. 实验结果表明, CdSe电沉积因条件不同遵循两种不同的机理, 据此讨论了克服Se/Cd比大于1的可能措施。     

铅在铜上电沉积的原位椭圆偏振法

采用循环伏安法(CV)和原位椭圆偏振法(SE)研究铅在铜电极上的电沉积行为。 原位椭圆偏振参数Ψ和Δ值的变化率在CV图峰电位处同时出现极值。 通过建立单层膜模型描述“电极-溶液”界面的结构并对椭圆偏振光谱数据进行拟合得到铅沉积层厚度随电位的变化规律。 拟合结果显示,铅在铜电极上的电沉积有3个不同的沉积速率,-0.20～-0.35 V之间沉积速率为0.003 nm/mV,-0.35～-0.48 V之间沉积速率为0.025 nm/mV,-0.48～-0.60 V之间沉积速率为0.116 nm/mV,由此表明铅的电沉积分为3个不同阶段：欠电位沉积阶段、欠电位沉积向本体沉积的过渡阶段和本体沉积阶段。     

Electro-oxidation of formic acid catalyzed by FePt nanoparticles

The electrocatalytic oxidation of formic acid at a gold electrode functionalized with FePt nanoparticles was studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) in a mixed solution of 0.1 M HCOOH and 0.1 M HClO4. The FePt bimetallic nanoparticles, with a mean diameter of 3 nm, were prepared by a chemical reduction method. The Au/FePt nanostructured electrode was prepared firstly by the deposition of FePt nanoparticles onto a clean Au electrode surface, followed by ultraviolet ozone treatment to remove the organic coating. In CV measurements, two well-defined anodic peaks were observed at +0.20 and +0.51 V (vs. a Ag/AgCl quasi-reference). The anodic peak at +0.20 V was attributed to the oxidation of HCOOH to CO2 on surface unblocked by CO, whereas the peak at +0.51 V was ascribed to the oxidation of surface-adsorbed CO (an intermediate product of HCOOH oxidation) and further oxidation of bulk HCOOH. From the onset potential and current density of the electro-oxidation of HCOOH, FePt nanoparticles exhibit excellent electrocatalytic activities as compared to Pt and other metal alloys. EIS measurements were carried out to further examine the reaction kinetics involved in the HCOOH electro-oxidation. The EIS responses were found to be strongly dependent on electrode potentials. At potentials more positive than -0.25 V (vs. Ag/AgCl), pseudo-inductive behavior was typically observed. At potentials between +0.3 and +0.5 V, the impedance response was found to reverse from the first quadrant to the second quadrant; such negative Faradaic impedance was indicative of the presence of an inductive component due to the oxidation of surface-adsorbed CO. The impedance responses returned to normal behavior at more positive potentials (+0.6 to +0.9 V). The mechanistic variation was attributed to the formation of different intermediates (CO or oxygen containing species) on the electrode surface in different potential regions. Two equivalent circuits were proposed to model these impedance behaviors.     

Glassy carbon paste electrodes

A new carbon composite electrode material, based on mixing glassy carbon (GC) microparticles with an organic pasting liquid is described. The resulting glassy carbon paste electrode (GCPE) combines the electrochemical properties of GC with the various advantages of composite electrodes. Glassy carbon pastes (GCPs) offer high electrochemical reactivity, a wide accessible potential window, a low background current, and are inexpensive, easy to prepare, modify, and renew. The new material has a lower double-layer capacitance and a higher heterogeneous rate constant (for ferricyanide) compared to conventional carbon pastes (CPs). Scanning electron microscopy (SEM) images indicate significant differences in the structure of GCPE and carbon paste electrode (CPE). Factors influencing the electrode kinetics of GCPE surfaces are discussed. The electrochemical properties and advantages of GCPE should be of broad utility in electroanalysis.     

Mechanism of electrochemical reactions of polyaniline films formed under the conditions of cathodic oxygen reduction

Polyaniline films (further, CPANI) were obtained under the conditions of oxygen cathodic reduction in the aniline-containing solution on the electrodes of mixed indium tin oxide (ITO), graphite, and gold. CPANI films are characterized by redox processes in the potential ranges of 0.1–0.2 V and ～0.4 V (SCE). These processes are caused by the polymer chain fragments of different structure and the ratio between the peaks corresponding to these processes varies significantly as dependent on the synthesis conditions (electrode material, stirring, etc). The mechanism of electrode processes on CPANI is studied using the methods of cyclic voltammetry and quartz microgravimetry. It is found that only hydrogen cations and supporting electrolyte anions participate in the electrode process at the potentials of 0.1–0.2 V. The mechanism of redox processes on the obtained polymer films is discussed.     

Preparation and Electrochemical Properties of the Pd-modified Cu Electrode for Nitrate Reduction in Water

The reduction of nitrate has gained renewed attention due to environmental problems like overfertilization and the increasing costs of purification of drinking water. The usual techniques (e.g. ion-exchange and biofiltration) have some disadvantages1. So …     

Microelectrochemical electronic effects in two-layer structures of distinct Prussian blue type metal hexacyanoferrates

The formation of a rigid bilayer structure from two metal hexacyanoferrates: Prussian blue (PB) and nickel hexacyanoferrate (NiHCNFe), as inner and outer films, respectively, has been demonstrated. To avoid intermingling of the granular cyanometallate microstructures, namely of the outer film (NiHCNFe) into the inner film (PB), the morphology of outer film material was changed by forming a polymeric hybrid (composite) of NiHCNFe with poly(N-methylpyrrole). The outer NiHCNFe film is physically separated from the electrode surface, and it undergoes redox reactions at potentials characteristic of the inner PB film. This arrangement leads to the reversible charge state trapping and bistable switching during voltammetric potential cycling. Under solid-state voltammetric conditions in the absence of contact with the liquid electrolyte phase, when the bilayer structure of PB and the oxidized NiHCNFe was formed between two sandwich-forming carbon electrodes, unidirectional rectifying current flow has been observed.Dedicated to Zbigniew Galus on the occasion of his 70th birthday     

Carbon nanotube detectors for microchip CE: comparative study of single-wall and multiwall carbon nanotube, and graphite powder films on glassy carbon, gold, and platinum electrode surfaces

The performance of microchip electrophoresis/electrochemistry system with carbon nanotube (CNT) film electrodes was studied. Electrocatalytic activities of different carbon materials (single-wall CNT (SWCNT), multiwall CNT (MWCNT), carbon powder) cast on different electrode substrates (glassy carbon (GC), gold, and platinum) were compared in a microfluidic setup and their performance as microchip electrochemical detectors was assessed. An MWCNT film on a GC electrode shows electrocatalytic effect toward oxidation of dopamine (E(1/2) shift of 0.09 V) and catechol (E(1/2) shift of 0.19 V) when compared to a bare GC electrode, while other CNT/carbon powder films on the GC electrode display negligible effects. Modification of a gold electrode by graphite powder results in a strong electrocatalytic effect toward oxidation of dopamine and catechol (E(1/2) shift of 0.14 and 0.11 V, respectively). A significant shift of the half-wave potentials to lower values also provide the MWCNT film (E(1/2) shift of 0.08 and 0.08 V for dopamine and catechol, respectively) and the SWCNT film (E(1/2) shift of 0.10 V for catechol) when compared to a bare gold electrode. A microfluidic device with a CNT film-modified detection electrode displays greatly improved separation resolution (R(s)) by a factor of two compared to a bare electrode, reflecting the electrocatalytic activity of CNT.     

Irreversible electrostatic deposition of Prussian blue from colloidal solutions

Prussian blue (PB) can be deposited from colloidal solutions (5.4?×?10^?3?mol_PB?L^?1, 0.01?mol?L^?1 KNO₃) on glassy carbon, either by potential cycling or potentiostatically, provided that the deposition potential is more positive than ?0.2?V vs. Hg/Hg₂Cl₂. Depending on the deposition potential, the PB particles form either a single layer of Everitt??s salt, of PB, or multilayers of Berlin green. Also depending on the electrode potential, the deposition was accompanied by currents which were either only of capacitive nature, or represent the sum of capacitive and faradaic currents. The currents were always limited by the diffusion of the colloidal particles to the electrode surface, i.e., they obeyed the Cottrell equation. The PB layers were characterized by in situ atomic force microscopy.     

Electrochemically deposited organic luminescent films: the effects of deposition parameters on morphologies and luminescent efficiency of films

The electropolymerization behaviors of an electroactive and luminescent compound TCPC as precursor are studied. The resultant electrochemical deposition (ED) films are characterized by cyclic voltammetry (CV), UV-vis, fluorescence spectra, scanning electron microscopy (SEM), and atomic force microscopy (AFM). Under the CV mode with potential range of -0.5 to 0.85 V vs Ag/Ag(+), the coupling reactions between the carbazole units of TCPC are very efficient, while the fluorescent trifluorene segment in TCPC is chemically inert in this potential range, which results in a highly fluorescent film formation on indium tin oxide (ITO) electrode. The deposition parameters for preparing the TCPC-based ED films are optimized, and the best ED film gives the fluorescence efficiency of 45.5% with surface roughness of 2.8 nm and morphologic stability as heating to 180 degrees C. The light-emitting devices (LEDs) using this ED film as light emitting layer with structure ITO/ED film (approximately 100 nm)/Ba/Al achieve maximum luminescence and external quantum efficiency of 4224 cd/m(2) at 17 V and 0.72% at 11.5 V, respectively, which are better than the device using TCPC spin-coating films as emitting layer. The technique provides a facile route toward a patternable luminescent film and device because such luminescent ED films can be manipulatively deposited on the electrified electrode.     

Glassy carbon paste electrodes modified with polyphenol oxidase: Analytical applications

The electrochemical behavior of a glassy carbon paste electrode (GCPE) is evaluated in comparison to that of graphite paste electrode (gPE) and glassy carbon electrode (GCE). Important shifting in the peak potentials and increases in the peak currents for catechol, ascorbic acid, dopamine and hydroquinone were obtained for the GCPE and its usefulness for the development of phenol and catechol biosensors was also evaluated. Both, pure mushroom polyphenol oxidase (PPO) and fresh mushroom tissues were used as biorecognition elements. The effect of the binder percentage in the composite material was also studied. The bioelectrode was used for the determination of dopamine and acetaminophen in pharmaceutical formulations and for the detection of polyphenols in wine and tea. The bioelectrode demonstrated to be very stable as the response remained around 90% after four months at 4 °C.     

Mechanistic Insights into Cyclic Voltammograms on Pt(111): Kinetics Simulations

A detailed understanding of the electrochemistry of platinum electrodes is of great importance for the electrochemical oxidation of fuels and electrochemical reduction of dioxygen in fuel cells. The Pt(111) facet is the most representative model mimicking Pt nanoparticles and polycrystals for fundamental studies. Herein, we propose a site-specific model accompanied with the typical elementary steps of the electrochemistry of Pt(111) in non-adsorbing electrolyte within the potential range between 0.05 and 1.15 V versus reversible hydrogen electrode. Simulations were conducted at different scanning rates based on the kinetics models. We reproduce all the anodic and cathodic peaks observed in the reported experimental curves. These results demonstrate the underlying mechanisms of the peak formation in different potential regions.     

Direct Electrochemistry with Nitrate Reductase in Chitosan Films

Stable films made from chitosan (CS) on pyrolytic graphite (PG) electrode gave direct electrochemistry for incorporated enzyme nitrate reductase (NR). Cyclic voltammetry (CV) of NR‐CS films showed a pair of well‐defined and nearly reversible redox peaks at about ?0.430 V vs. SCE at pH 7.0 phosphate buffers, which was considered as the redox of FAD and heme‐ion. The electron transfer between NR and PG electrode was greatly facilitated in CS films. Integration of reduction peaks at different scan rates from 0.01 to 0.5 V s^?;1 gave nearly constant charge values, which is characteristic of thin‐larger‐electrochemical behavior. The pH of the solution strongly affected the direct electron transfer of NR‐CS films. EDTA accelerated the electron transfer, and it was proposed as a stimulant for the system. Reflectance absorption infrared spectra demonstrated that NR retained a nearly native conformation in CS films.     

Electrochemical synthesis of Zn-Al layered double hydroxide (LDH) films

A new electrodeposition condition to produce Zn-Al LDH films was developed using nitrate solutions containing Zn (2+) and Al (3+) ions. Deposition was achieved by reducing nitrate ions to generate hydroxide ions on the working electrode. This elevates the local pH on the working electrode, resulting in precipitation of Zn-Al LDH films. The effect of deposition potential, pH of the plating solution, and the Zn (2+) to Al (3+) ratio in the plating solution on the purity and crystallinity of the LDH films deposited was systematically studied using X-ray diffraction and energy dispersive spectroscopy (EDS). The optimum deposition potential to deposit pure and well-ordered Zn-Al LDH films was E = -1.65V versus a Ag/AgCl in 4 M KCl reference electrode at room temperature using a solution containing 12.5 mM Zn(NO 3) 2.6H 2O and 7.5 mM Al(NO 3) 3.9H 2O with pH adjusted to 3.8. The resulting film contained 39 atomic %Al (3+) ions replacing Zn (2+) ions, leading to a composition of Zn 0.61Al 0.39(OH) 2(NO 3) 0.39. xH 2O. Increasing or decreasing the aluminum concentration in the plating solution resulted in the formation of aluminum- or zinc-containing impurities, respectively, instead of varying aluminum content incorporated into the LDH phase. Choosing an optimum deposition potential was important to obtain LDH as a pure phase in the film. When the potential more negative than the optimum potential is used, zinc metal or zinc hydroxide was deposited as a side product, whereas making the potential less negative than the optimum potential resulted in the formation of zinc oxide as the major phase. The pH condition of the plating solution was also critical, as increasing pH destabilizes the formation of the LDH phase while decreasing pH promoted deposition of other impurities.