Anisotropy enhanced X‐ray scattering from solvated transition metal complexes

Time‐resolved X‐ray scattering patterns from photoexcited molecules in solution are in many cases anisotropic at the ultrafast time scales accessible at X‐ray free‐electron lasers (XFELs). This anisotropy arises from the interaction of a linearly polarized UV–Vis pump laser pulse with the sample, which induces anisotropic structural changes that can be captured by femtosecond X‐ray pulses. In this work, a method for quantitative analysis of the anisotropic scattering signal arising from an ensemble of molecules is described, and it is demonstrated how its use can enhance the structural sensitivity of the time‐resolved X‐ray scattering experiment. This method is applied on time‐resolved X‐ray scattering patterns measured upon photoexcitation of a solvated di‐platinum complex at an XFEL, and the key parameters involved are explored. It is shown that a combined analysis of the anisotropic and isotropic difference scattering signals in this experiment allows a more precise determination of the main photoinduced structural change in the solute, i.e. the change in Pt—Pt bond length, and yields more information on the excitation channels than the analysis of the isotropic scattering only. Finally, it is discussed how the anisotropic transient response of the solvent can enable the determination of key experimental parameters such as the instrument response function.     

Integration method for directly analyzing interface statistics of periodic multilayers from X‐ray scattering

An integration method is demonstrated for directly determining the average interface statistics of periodic multilayers from the X‐ray scattering diagram. By measuring the X‐ray scattering diagram in the out‐of‐plane geometry and integrating the scattered intensity along the vertical momentum transfer q_z in an interval, which is decided by the thickness ratio Γ (ratio of sublayer's thickness to periodic thickness), the cross‐correlations between different interfaces are canceled and only the autocorrelations are reserved. Then the multilayer can be treated as a `single interface' and the average power spectral density can be obtained without assuming any vertical correlation model. This method has been employed to study the interface morphology of sputter‐deposited W/Si multilayers grown at an Ar pressure of 1–7 mTorr. The results show an increase in vertical correlation length and a decrease in lateral correlation length with increased Ar pressure. The static roughness exponent α = 0 and dynamic growth exponent z = 2 indicate the Edwards–Wilkinson growth model at an Ar pressure of 1–5 mTorr. At an Ar pressure of 7 mTorr, α = 0.35 and z = 1.65 indicate the Kardar–Parisi–Zhang growth model.     

X‐ray Raman spectroscopy of lithium‐ion battery electrolyte solutions in a flow cell

The effects of varying LiPF₆ salt concentration and the presence of lithium bis(oxalate)borate additive on the electronic structure of commonly used lithium‐ion battery electrolyte solvents (ethylene carbonate–dimethyl carbonate and propylene carbonate) have been investigated. X‐ray Raman scattering spectroscopy (a non‐resonant inelastic X‐ray scattering method) was utilized together with a closed‐circle flow cell. Carbon and oxygen K‐edges provide characteristic information on the electronic structure of the electrolyte solutions, which are sensitive to local chemistry. Higher Li⁺ ion concentration in the solvent manifests itself as a blue‐shift of both the π* feature in the carbon edge and the carbonyl π* feature in the oxygen edge. While these oxygen K‐edge results agree with previous soft X‐ray absorption studies on LiBF₄ salt concentration in propylene carbonate, carbon K‐edge spectra reveal a shift in energy, which can be explained with differing ionic conductivities of the electrolyte solutions.     

Fabrication of polycrystalline silicon films by Al‐induced crystallization of silicon‐rich oxide films

Polycrystalline silicon (poly‐Si) films were fabricated by aluminum (Al)‐induced crystallization of Si‐rich oxide (SiO_x) films. The fabrication was achieved by thermal annealing of SiO_x /Al bilayers below the eutectic temperature of the Al–Si alloy. The poly‐Si film resulting from SiO_1.45 exhibited good crystallinity with highly preferential (111) orientation, as deduced from Raman scattering, X‐ray diffraction, and transmission electron microscopy measurements. The poly‐Si film is probably formed by the Al‐induced layer exchange mechanism, which is mediated by Al oxide.     

Implementation of a beam deflection system for studies of liquid interfaces on beamline I07 at Diamond

X‐ray optics, based on a double‐crystal deflection scheme, that enable reflectivity measurements from liquid surfaces/interfaces have been designed, built and commissioned on beamline I07 at Diamond Light Source. This system is able to deflect the beam onto a fixed sample position located at the centre of a five‐circle diffractometer. Thus the incident angle can be easily varied without moving the sample, and the reflected beam is tracked either by a moving Pilatus 100K detector mounted on the diffractometer arm or by a stationary Pilatus 2M detector positioned appropriately for small‐angle scattering. Thus the system can easily combine measurements of the reflectivity from liquid interfaces (Q_z > 1 Å^?1) with off‐specular data collection, both in the form of grazing‐incidence small‐angle X‐ray scattering (GISAXS) or wider‐angle grazing‐incidence X‐ray diffraction (GIXD). The device allows operation over the energy range 10–28 keV.     

Formation and Raman scattering of seed‐like ZnO nanostructure

This work demonstrates seed‐like ZnO nanostructure aggregated with nano‐entities using the colloid chemical method. The formation mechanism and optical properties of the ZnO nanostructure are studied. The X‐ray diffraction spectrum indicates that the ZnO nanostructures are polycrystalline pure wurtzite phase. Multiphonon processes in the nanostructure are identified from the Raman scattering spectra in the spectral range of 300–2000 cm⁻¹. A strong violet photoluminescence band emission was visible in the room temperature photoluminescence spectra. This work determines the quality of such crystals and extends the optical applications of ZnO nanostructures. Copyright © 2009 John Wiley & Sons, Ltd.     

Measurement of the X‐ray mass attenuation coefficients of silver in the 5–20 keV range

The X‐ray mass attenuation coefficients of silver were measured in the energy range 5–20 keV with an accuracy of 0.01–0.2% on a relative scale down to 5.3 keV, and of 0.09–1.22% on an absolute scale to 5.0 keV. This analysis confirms that with careful choice of foil thickness and careful correction for systematics, especially including harmonic contents at lower energies, the X‐ray attenuation of high‐Z elements can be measured with high accuracy even at low X‐ray energies (<6 keV). This is the first high‐accuracy measurement of X‐ray mass attenuation coefficients of silver in the low energy range, indicating the possibility of obtaining high‐accuracy X‐ray absorption fine structure down to the L₁ edge (3.8 keV) of silver. Comparison of results reported here with an earlier data set optimized for higher energies confirms accuracy to within one standard error of each data set collected and analysed using the principles of the X‐ray extended‐range technique (XERT). Comparison with theory shows a slow divergence towards lower energies in this region away from absorption edges. The methodology developed can be used for the XAFS analysis of compounds and solutions to investigate structural features, bonding and coordination chemistry.     

The use of X‐ray interaction data to differentiate malignant from normal breast tissue at surgical margins and biopsy analysis

X‐ray interaction data, including measuring bio‐metal levels and scattering characteristics, are being shown to be a possible discriminating variable in the classification of human tissues. However, a major concern when using X‐ray interaction data in breast cancer material is that the samples are rarely 100% tumour because of the invasive nature of the disease. The work reported here includes a methodology to help overcome this limitation as the experimental protocol includes mapping the data to histological analysis of the measured samples. This work has shown how important it is to relate the measured X‐ray parameters to the histology of the samples, particularly the clinical information that describes the percentage of tumour within each sample. Levels of K, Ca, Zn, Fe, Cu, Br and Rb were evaluated using X‐ray fluorescence and compared between tumour breast tissue and normal surrounding breast tissue. The coherent scattering properties of each sample were also examined using an angular dispersive X‐ray diffraction technique. Multivariate modelling using soft independent modelling of class analogy was used to classify samples kept out of the modelling procedure. A significant increase (p < 0.01) in the levels of Rb, Zn and K was found in the tumour samples. The levels of these elements show a correlation with the percentage of tumour reported to be present in a given sample. The results of classifying unknown tissue samples are presented using two‐class and three‐class models that help to reveal the importance of sample histology in studies involving breast cancers. Copyright © 2013 John Wiley & Sons, Ltd.     

Soft X‐ray absorption spectroscopy and resonant inelastic X‐ray scattering spectroscopy below 100 eV: probing first‐row transition‐metal M‐edges in chemical complexes

X‐ray absorption and scattering spectroscopies involving the 3d transition‐metal K‐ and L‐edges have a long history in studying inorganic and bioinorganic molecules. However, there have been very few studies using the M‐edges, which are below 100 eV. Synchrotron‐based X‐ray sources can have higher energy resolution at M‐edges. M‐edge X‐ray absorption spectroscopy (XAS) and resonant inelastic X‐ray scattering (RIXS) could therefore provide complementary information to K‐ and L‐edge spectroscopies. In this study, M_2,3‐edge XAS on several Co, Ni and Cu complexes are measured and their spectral information, such as chemical shifts and covalency effects, are analyzed and discussed. In addition, M_2,3‐edge RIXS on NiO, NiF₂ and two other covalent complexes have been performed and different d–d transition patterns have been observed. Although still preliminary, this work on 3d metal complexes demonstrates the potential to use M‐edge XAS and RIXS on more complicated 3d metal complexes in the future. The potential for using high‐sensitivity and high‐resolution superconducting tunnel junction X‐ray detectors below 100 eV is also illustrated and discussed.     

The status of strontium in biological apatites: an XANES/EXAFS investigation

Osteoporosis represents a major public health problem through its association with fragility fractures. The public health burden of osteoporotic fractures will rise in future generations, due in part to an increase in life expectancy. Strontium‐based drugs have been shown to increase bone mass in postmenopausal osteoporosis patients and to reduce fracture risk but the molecular mechanisms of the action of these Sr‐based drugs are not totally elucidated. The local environment of Sr²⁺ cations in biological apatites present in pathological and physiological calcifications in patients without such Sr‐based drugs has been assessed. In this investigation, X‐ray absorption spectra have been collected for 17 pathological and physiological calcifications. These experimental data have been combined with a set of numerical simulations using the ab initioFEFF9 X‐ray spectroscopy program which takes into account possible distortion and Ca/Sr substitution in the environment of the Sr²⁺ cations. For selected samples, Fourier transforms of the EXAFS modulations have been performed. The complete set of experimental data collected on 17 samples indicates that there is no relationship between the nature of the calcification (physiological and pathological) and the adsorption mode of Sr²⁺ cations (simple adsorption or insertion). Such structural considerations have medical implications. Pathological and physiological calcifications correspond to two very different preparation procedures but are associated with the same localization of Sr²⁺versus apatite crystals. Based on this study, it seems that for supplementation of Sr at low concentration, Sr²⁺ cations will be localized into the apatite network.     

On the Supermolecular Structure of Fullerene C60 Solutions

Small angle X‐ray scattering (SAXS) and wide angle X‐ray scattering (WAXS) techniques were used for investigation of fullerene C₆₀ solutions in toluene and p‐xylene. On all SAXS curves, intensity decreases to some constant value of I_C with increase of scattering angle. The value of I_C depends on concentration non‐monotonically: it first slightly increases, then drops sharply to some minimal value, and then increases again. A qualitative explanation of such dependence is offered. It is supposed that the presence of fullerene C₆₀ in solution suppresses thermal fluctuations of density in the solvent. In combination with the X‐ray data the results obtained for solutions of fullerene C₆₀ by various others techniques (calorimetry, densimetry, etc.) are discussed. Possible models of a supermolecular structure of fullerene C₆₀ solutions in good solvents are considered.     

Sound velocities of compressed Fe3C from simultaneous synchrotron X‐ray diffraction and nuclear resonant scattering measurements

The applications of nuclear resonant scattering in laser‐heated diamond anvil cells have provided an important probe for the magnetic and vibrational properties of ⁵⁷Fe‐bearing materials under high pressure and high temperature. Synchrotron X‐ray diffraction is one of the most powerful tools for studying phase stability and equation of state over a wide range of pressure and temperature conditions. Recently an experimental capability has been developed for simultaneous nuclear resonant scattering and X‐ray diffraction measurements using synchrotron radiation. Here the application of this method to determine the sound velocities of compressed Fe₃C is shown. The X‐ray diffraction measurements allow detection of microscale impurities, phase transitions and chemical reactions upon compression or heating. They also provide information on sample pressure, grain size distribution and unit cell volume. By combining the Debye velocity extracted from the nuclear resonant inelastic X‐ray scattering measurements and the structure, density and elasticity data from the X‐ray diffraction measurements simultaneously obtained, more accurate sound velocity data can be derived. Our results on few‐crystal and powder samples indicate strong anisotropy in the sound velocities of Fe₃C under ambient conditions.     

Nanocomposite characterization on multiple length scales using µSAXS

Nanocomposites have great potential for the rational synthesis of tailored materials. However, the templating process that transfers the self‐organized nanostructure of a block copolymer or other mesophase onto the functional material is by no means trivial, and often involves multiple steps, each of which presents its own chemical and physical challenges. As a result the nanocomposite may not be homogeneous, but can be phase‐separated into various components which may feature their own specific microstructure. Here it is shown how scanning microbeam small‐angle X‐ray scattering (µSAXS) can be used to characterize a thermoset resol/poly(isoprene‐block‐ethylene oxide) nanocomposite on multiple length scales with respect to homogeneity and microphase separation.     

Thorough small‐angle X‐ray scattering analysis of the instability of liquid micro‐jets in air

Liquid jets are of interest, both for their industrial relevance and for scientific applications (more important, in particular for X‐rays, after the advent of free‐electron lasers that require liquid jets as sample carrier). Instability mechanisms have been described theoretically and by numerical simulation, but confirmed by few experimental techniques. In fact, these are mainly based on cameras, which is limited by the imaging resolution, and on light scattering, which is hindered by absorption, reflection, Mie scattering and multiple scattering due to complex air/liquid interfaces during jet break‐up. In this communication it is demonstrated that synchrotron small‐angle X‐ray scattering (SAXS) can give quantitative information on liquid jet dynamics at the nanoscale, by detecting time‐dependent morphology and break‐up length. Jets ejected from circular tubes of different diameters (100–450 µm) and speeds (0.7–21 m s^?1) have been explored to cover the Rayleigh and first wind‐induced regimes. Various solvents (water, ethanol, 2‐propanol) and their mixtures have been examined. The determination of the liquid jet behaviour becomes essential, as it provides background data in subsequent studies of chemical and biological reactions using SAXS or X‐ray diffraction based on synchrotron radiation and free‐electron lasers.     

A large‐solid‐angle X‐ray Raman scattering spectrometer at ID20 of the European Synchrotron Radiation Facility

An end‐station for X‐ray Raman scattering spectroscopy at beamline ID20 of the European Synchrotron Radiation Facility is described. This end‐station is dedicated to the study of shallow core electronic excitations using non‐resonant inelastic X‐ray scattering. The spectrometer has 72 spherically bent analyzer crystals arranged in six modular groups of 12 analyzer crystals each for a combined maximum flexibility and large solid angle of detection. Each of the six analyzer modules houses one pixelated area detector allowing for X‐ray Raman scattering based imaging and efficient separation of the desired signal from the sample and spurious scattering from the often used complicated sample environments. This new end‐station provides an unprecedented instrument for X‐ray Raman scattering, which is a spectroscopic tool of great interest for the study of low‐energy X‐ray absorption spectra in materials under in situ conditions, such as in operando batteries and fuel cells, in situ catalytic reactions, and extreme pressure and temperature conditions.     

Insight into growth of Au–Pt bimetallic nanoparticles: an in situ XAS study

Au–Pt bimetallic nanoparticles have been synthesized through a one‐pot synthesis route from their respective chloride precursors using block copolymer as a stabilizer. Growth of the nanoparticles has been studied by simultaneous in situ measurement of X‐ray absorption spectroscopy (XAS) and UV–Vis spectroscopy at the energy‐dispersive EXAFS beamline (BL‐08) at Indus‐2 SRS at RRCAT, Indore, India. In situ XAS spectra, comprising both X‐ray near‐edge structure (XANES) and extended X‐ray absorption fine‐structure (EXAFS) parts, have been measured simultaneously at the Au and Pt L₃‐edges. While the XANES spectra of the precursors provide real‐time information on the reduction process, the EXAFS spectra reveal the structure of the clusters formed in the intermediate stages of growth. This insight into the formation process throws light on how the difference in the reduction potential of the two precursors could be used to obtain the core–shell‐type configuration of a bimetallic alloy in a one‐pot synthesis method. The core–shell‐type structure of the nanoparticles has also been confirmed by ex situ energy‐dispersive spectroscopy line‐scan and X‐ray photoelectron spectroscopy measurements with in situ ion etching on fully formed nanoparticles.     

In situ removal of carbon contamination from optics in a vacuum ultraviolet and soft X‐ray undulator beamline using oxygen activated by zeroth‐order synchrotron radiation

Carbon contamination of optics is a serious issue in all soft X‐ray beamlines because it decreases the quality of experimental data, such as near‐edge X‐ray absorption fine structure, resonant photoemission and resonant soft X‐ray emission spectra in the carbon K‐edge region. Here an in situ method involving the use of oxygen activated by zeroth‐order synchrotron radiation was used to clean the optics in a vacuum ultraviolet and soft X‐ray undulator beamline, BL‐13A at the Photon Factory in Tsukuba, Japan. The carbon contamination of the optics was removed by exposing them to oxygen at a pressure of 10^?1–10^?4 Pa for 17–20 h and simultaneously irradiating them with zeroth‐order synchrotron radiation. After the cleaning, the decrease in the photon intensity in the carbon K‐edge region reduced to 2–5%. The base pressure of the beamline recovered to 10^?7–10^?8 Pa in one day without baking. The beamline can be used without additional commissioning.