超氧化物歧化酶在纳米金/L-半胱氨酸修饰金电极上的电化学行为

通过L-半胱氨酸将纳米金修饰到金电极上,把超氧化物歧化酶(SOD)固定在修饰电极表面,制备了SOD-纳米金/L-半胱氨酸修饰电极。运用交流阻抗法、循环伏安法等方法表征了该电极,发现SOD在该电极上于0.15V和-0.05V左右产生较明显的氧化还原峰,在0.04～0.24V/s扫描速率范围内,其还原峰电流与扫描速速呈线性关系,表明该电极过程受吸附控制。研究了H2O2对SOD-纳米金/L-半胱氨酸修饰电极伏安行为的影响,发现该电极的还原峰电流与H2O2浓度在1.0×10-6～2.0×10-4mol/L范围内呈良好的线性关系,相关系数为-0.996,可用于对H2O2的分析检测。     

基于Nafion-氧化石墨烯复合物/硫堇/纳米金构建过氧化氢传感器的研究

利用Nafion(全氟聚苯乙烯磺酸溶液)-氧化石墨烯复合物、硫堇和纳米金构建了H2O2酶传感器。首先将氧化石墨烯分散在体积分数0.2%Nafion溶液中制得Nafion-氧化石墨烯的复合物,并将其固定在玻碳电极表面,通过静电吸附将带正电荷的硫堇吸附到Nafion-氧化石墨烯复合膜修饰的玻碳电极表面,再利用静电吸附将纳米金修饰于电极上,通过纳米金来固定辣根过氧化物酶从而制得H2O2传感器。用循环伏安法和计时电流法考察该修饰电极的电化学特性。H2O2浓度为5.5×10-6~1.0×10-3mol/L时,酶电极的响应电流值与H2O2的浓度呈良好的线性关系,检出限为1.80×10-6mol/L。     

聚L-酪氨酸/半胱氨酸/纳米金修饰Pt电极固定血红蛋白测定H2O2

制备了聚L-酪氨酸/半胱氨酸/纳米金/血红蛋白修饰Pt电极,并用循环伏安法和交流阻抗法对制备过程进行了表征。还用循环伏安法和计时电流法研究了修饰电极与H2O2的相互作用。结果表明,该电极对H2O2有明显的催化作用,电流与H2O2浓度在3.5×10-7~2.0×10-3mol/L范围内呈线性关系,检出限为1.0×10-7mol/L。     

铜纳米粒子在碳纳米管上的原位生长及对过氧化氢电催化性能的研究

采用一种温和且有效的方法,将聚丙烯酸非共价修饰到碳纳米管上,并以其为模板,在碳纳米管上原位均匀的生长铜纳米粒子,制备了铜/聚丙烯酸/碳纳米管(Cu/PAA/CNT)纳米复合材料,并以此材料构建了一种新型的非酶H2O2传感器,研究了其对H2O2的电催化行为。结果表明:铜纳米粒子较均匀的生长在碳纳米管上,制备的纳米复合材料修饰到电极表面对H2O2表现出良好的电流响应,可实现对H2O2的灵敏测定,其响应电流与H2O2的浓度在1.9×10-6～8.0×10-4mol/L范围内呈良好的线性关系,检测限达6.3×10-7mol/L。     

金复合介孔SBA-15吸附血红蛋白在H2O2电催化反应中的应用

以P123嵌段共聚物表面活性剂为模板剂制备介孔氧化硅SBA-15,并用沉积-沉淀(DP)法在SBA-15介孔表面负载纳米Au颗粒制备得到金复合介孔SBA-15材料(Au-SBA-15).再以Au-SBA-15材料制备玻碳修饰电极,将血红蛋白固定于修饰电极上用循环伏安法考察其对不同浓度H2O2溶液的电催化反应.在固定了血红蛋白的Hb/Au-SBA-15/GC修饰电极上,H2O2在+0.95 V处出现了氧化峰,且随着H2O2浓度的增大峰电流不断增加,说明金复合介孔氧化硅材料具有良好的生物兼容性,有利于血红蛋白的固定,其修饰电极对H2O2溶液具有一定的电催化作用.     

三维有序石墨烯掺杂纳米二氧化钛酶生物传感器

采用模板法在氧化铟锡电极上制备了三维有序多孔结构的石墨烯掺杂纳米二氧化钛修饰电极,并在此修饰电极上成功固定了过氧化氢酶,从而构建了一种新型的H2O2生物传感器。 通过循环伏安、交流阻抗及计时电流等方法研究了该修饰电极的电化学特性,实验结果表明,该修饰电极对H2O2有良好的电催化作用,对H2O2的检测线性范围为3.0×10-6~3.6×10-3 mol/L,检测限为4.2×10-7 mol/L(S/N=3);且传感器响应迅速、灵敏度高、重现性和稳定性好。     

基于场放大进样及Au纳米粒子双重富集用于大肠杆菌检测的毛细管电泳电化学免疫分析法

利用Au纳米粒子作为辣根过氧化物酶(HRP)标记抗体的载体,结合电堆积预富集技术,发展了一种基于场放大进样及Au纳米粒子双重富集的毛细管电泳电化学免疫分析技术用于大肠杆菌的检测.大肠杆菌与酶标抗体免疫反应后直接进行场放大进样预富集,免疫样品快速迁移并堆积在毛细管入口端,同时带负电荷的金纳米粒子向阳极端迁移,在样品与缓冲溶液的界面处吸附样品离子.金纳米粒子作为多酶载体使检测信号进一步放大.以标记在抗体上的HRP催化H2O2氧化邻苯二胺产生的电流信号来检测大肠杆菌.同常规电动进样毛细管电泳相比,该双重富集技术可使灵敏度提高1400倍.该方法对大肠杆菌检测的线性范围为2.0～2000.0 cfu mL-1,检出限为1.0 cfu mL-1,实现了对扇贝样品中大肠杆菌的快速、灵敏检测.     

电聚合茜素黄R构建辣根过氧化物酶传感器的研究

利用电聚合茜素黄R(AYR)的方法,将辣根过氧化物酶(HRP)和细胞色素c(Cyt c)固载于通过一步法电沉积的碳纳米管-金纳米粒子(MWCNTsAu NPs)复合纳米材料修饰电极表面,构筑PAYR-HRP-Cyt c/M WCNTs-Au NPs修饰电极,并利用HRP对H2O2的直接电化学催化行为对H2O2进行检测。采用扫描电镜对MWCNTs-Au NPs和PAYR-HRP-Cyt c的表面形貌进行表征。利用电化学阻抗对修饰电极的构筑过程进行了监测。采用循环伏安法和计时电流法对修饰电极的电化学行为进行了研究。探讨了p H和电位对该修饰电极测定H2O2的性能的影响。该传感器对H2O2在5.0×10-7~3.14×10-3mol/L范围内呈良好的线性响应,相关系数为0.9997,灵敏度为0.50 A·L/mol,检出限(S/N=3)为9.6×10-8mol/L。     

基于L-半胱氨酸、纳米金自组装的葡萄糖生物传感器的构建

制备了基于L-半胱氨酸、纳米金自组装的新型葡萄糖生物传感器。用L-半胱氨酸修饰裸金电极,并利用静电吸附的原理固定纳米金,最后通过交联剂使酶固定在修饰后的电极上制成葡萄糖生物传感器。L-半胱氨酸-纳米金以及酶的修饰提高了电极传递电子的能力。通过正交试验选取了最佳的交联条件:6 g/L葡萄糖氧化酶、0.6 g/L过氧化氢酶、0.03%1-乙基-[3-二甲基氨基丙基]碳酰二亚胺盐酸化物、0.03%N-羟基琥珀酰亚胺及p H 7.0的缓冲溶液。该传感器对葡萄糖溶液浓度有良好的线性关系,线性范围为1~16 mmol/L,线性回归方程为I=0.2512c+1.9583,相关系数达到0.9996,具有一定的抗干扰能力。该葡萄糖生物传感器电流大小与葡萄糖浓度呈现良好的线性关系,在临床检验上具有一定的应用前景。     

基于二氧化硅-硫堇纳米复合物构建高灵敏癌胚抗原电流型免疫传感器

利用电沉积纳米金(AuNPs)修饰玻碳电极(GCE)表面并通过AuNPs固定癌胚抗原(CEA)的捕获抗体(Ab1),以牛血清白蛋白(BSA)封闭非特异性吸附位点;以γ-(2,3环氧丙氧)丙基三甲氧基硅烷(GPMS)作交联剂,将单分散的SiO_2纳米粒子与电子媒介体硫堇(Thi)结合成SiO_2-Thi纳米复合物,偶联辣根过氧化物酶(HRP)标记的CEA二抗(HRP-Ab2)作为电化学免疫检测信号,构建了具有信号放大效应的电流型免疫传感器并用于CEA的高灵敏检测。在CEA存在下,进行电化学酶联夹心免疫反应。在含有H2O2的磷酸盐缓冲溶液(PBS)中,标记在SiO_2-Thi纳米复合物上的HRP能催化H_2O_2氧化电子媒介体Thi,产生增强的还原峰电流,从而提高检测CEA的峰电流响应信号,进而实现对CEA的高灵敏电化学酶联夹心免疫分析。在最优实验条件下,该免疫传感器的差分脉冲伏安(DPV)还原峰电流与CEA质量浓度的对数在0.01~20ng/mL范围内呈良好的线性关系,检出限为3pg/mL(S/N=3)。该传感器对血清样品进行加标回收实验,回收率为97.3%~105.7%,可初步用于临床对CEA的检测。     

A non-enzymatic sensor for hydrogen peroxide based on polyaniline, multiwalled carbon nanotubes and gold nanoparticles modified Au electrode

We describe the construction of a polyaniline (PANI), multiwalled carbon nanotubes (MWCNTs) and gold nanoparticles (AuNPs) modified Au electrode for determination of hydrogen peroxide without using peroxidase (HRP). The AuNPs/MWCNT/PANI composite film deposited on Au electrode was characterized by Scanning Electron Microscopy (SEM) and electrochemical methods. Cyclic voltammetric (CV) studies of the electrode at different stages of construction demonstrated that the modified electrode had enhanced electrochemical oxidation of H(2)O(2), which offers a number of attractive features to develop amperometric sensors based on split of H(2)O(2). The amperometric response to H(2)O(2) showed a linear relationship in the range from 3.0 μM to 600.0 μM with a detection limit of 0.3 μM (S/N = 3) and with high sensitivity of 3.3 mA μM(-1). The sensor gave accurate and satisfactory results, when employed for determination of H(2)O(2) in milk and urine.     

Effect of pH on direct electron transfer in the system gold electrode-recombinant horseradish peroxidase.

The effect of pH on the kinetics of the bioelectrocatalytic reduction of H(2)O(2) catalysed by horseradish peroxidase (HRP) has been studied at -50 mV vs. Agmid R:AgCl on HRP-modified Au electrodes placed in a wall-jet flow-through electrochemical cell. Native HRP (nHRP) and a nonglycosylated recombinant form containing a six-histidine tag at the C-terminus, C(His)rHRP, produced by genetic engineering of nonglycosylated recombinant HRP using an E. coli expression system, have been used for adsorptive modification of Au electrodes. A favourable adsorption of C(His)rHRP on pre-oxidized Au from a protein solution at pH 6.0 provided a high and stable current response to H(2)O(2) due to its bioelectrocatalytic reduction based on direct (mediator-less) electron transfer (ET) between Au and the active site of HRP. The heterogeneous ET rate constant, k(s), calculated from experimental data on direct ET, on mediated ET in the presence of catechol as well as from microbalance data, increased more than 30 times when changing from nHRP to C(His)rHRP. For both forms of HRP, the increasing efficiency of bioelectrocatalysis with increasing [H(3)O(+)] was observed. The values of the apparent k(s) between C(His)rHRP and Au changed from a value of 12+/-2 s(-1) in PBS at pH 8.0 to a value of 434+/-62 s(-1) at pH 6.0; a similar k(s)-pH dependence was also observed for nHRP, providing the possibility to consider the reaction mechanism involving the participation of a proton in the rate-determining step of the charge transfer.     

Direct deposition of gold nanoparticles onto polymer beads and glucose oxidation with H2O2

Gold nanoparticles (Au NPs) were deposited directly from aqueous solution of diethylenediaminegold(III) complex onto polymer beads commercially available, such as poly(methyl methacrylate) (PMMA), polystyrene (PS), and polyaniline (PANI) without surface modification. The dropwise addition of NaBH4 to reduce Au(III) was found to be very effective to obtain small Au0 NPs with a narrow size distribution except for PANI. The catalytic performance of Au NPs deposited on polymer beads for H2O2 decomposition and glucose oxidation with H2O2 were more significantly affected by the kinds of polymer supports than by the size of Au NPs. The equimolar oxidation of glucose with H2O2 could be operated by controlling the decomposition rate of H2O2 over Au/PMMA.     

Single atom hot-spots at Au-Pd nanoalloys for electrocatalytic H2O2 production

A novel strategy to direct the oxygen reduction reaction to preferentially produce H(2)O(2) is formulated and evaluated. The approach combines the inertness of Au nanoparticles toward oxidation, with the improved O(2) sticking probability of isolated transition metal "guest" atoms embedded in the Au "host". DFT modeling was employed to screen for the best alloy candidates. Modeling indicates that isolated alloying atoms of Pd, Pt, or Rh placed within the Au surface should enhance the H(2)O(2) production relative to pure Au. Consequently, Au(1-x)Pd(x) nanoalloys with variable Pd content supported on Vulcan XC-72 were prepared to investigate the predicted selectivity toward H(2)O(2) production for Au alloyed with Pd. It is demonstrated that increasing the Pd concentration to 8% leads to an increase of the electrocatalytic H(2)O(2) production selectivity up to nearly 95%, when the nanoparticles are placed in an environment compatible with that of a proton exchange membrane. Further increase of Pd content leads to a drop in H(2)O(2) selectivity, to below 10% for x = 0.5. It is proposed that the enhancement in H(2)O(2) selectivity is caused by the presence of individual surface Pd atoms surrounded by gold, whereas surface ensembles of contiguous Pd atoms support H(2)O formation. The results are discussed in the context of exergonic electrocatalytic H(2)O(2) synthesis in Polymer Electrolyte Fuel Cells for the simultaneous cogeneration of chemicals and electricity, the latter a credit to production costs.     

Selective growth of Au nanoparticles on (111) facets of Cu2O microcrystals with an enhanced electrocatalytic property

The selective growth of Au nanoparticles on (111) facets of truncated octahedral and cuboctahedral Cu(2)O crystals has been achieved by exploiting the differences in the standard potential between AuCl(4)(-)/Au and Cu(2+)/Cu(2)O pairs and in surface energies between (111) and (100) planes. The density and size of Au nanoparticles can be controlled by tuning the concentration of the gold precursor. Truncated octahedral Cu(2)O-Au nanocomposites have a 10 times higher electrochemically catalytic activity toward H(2)O(2) reduction than do pure Cu(2)O crystals. The enhanced catalysis may be derived from the polarization of Au NPs at the interface, which makes Cu(2)O more active for H(2)O(2) reduction.     

Selective conversion of cellobiose and cellulose into gluconic acid in water in the presence of oxygen, catalyzed by polyoxometalate-supported gold nanoparticles

Gold nanoparticles loaded onto Keggin-type insoluble polyoxometalates (Cs(x)H(3-x)PW(12)O(40)) showed superior catalytic performances for the direct conversion of cellobiose into gluconic acid in water in the presence of O(2). The selectivity of Au/Cs(x)H(3-x)PW(12)O(40) for gluconic acid was significantly higher than those of Au catalysts loaded onto typical metal oxides (e.g., SiO(2), Al(2)O(3), and TiO(2)), carbon nanotubes, and zeolites (H-ZSM-5 and HY). The acidity of polyoxometalates and the mean-size of the Au nanoparticles were the key factors in the catalytic conversion of cellobiose into gluconic acid. The stronger acidity of polyoxometalates not only favored the conversion of cellobiose but also resulted in higher selectivity of gluconic acid by facilitating desorption and inhibiting its further degradation. On the other hand, the smaller Au nanoparticles accelerated the oxidation of glucose (an intermediate) into gluconic acid, thereby leading to increases both in the conversion of cellobiose and in the selectivity of gluconic acid. The Au/Cs(x)H(3-x)PW(12)O(40) system also catalyzed the conversion of cellulose into gluconic acid with good efficiency, but it could not be used repeatedly owing to the leaching of a H(+)-rich hydrophilic moiety over long-term hydrothermal reactions. We have demonstrated that the combination of H(3)PW(12)O(40) and Au/Cs(3.0)PW(12)O(40) afforded excellent yields of gluconic acid (about 85%, 418 K, 11 h), and the deactivation of the recovered H(3)PW(12)O(40)-Au/Cs(3.0)PW(12)O(40) catalyst was not serious during repeated use.     

Porous Fe3O4 nanoparticles: synthesis and application in catalyzing epoxidation of styrene

A facile route was employed to synthesize porous magnetite via reaction of FeCl(3)·6H(2)O with N(2)H(4)·H(2)O in ethylene glycol without any structure-directing agent. The resultant Fe(3)O(4) particles were characterized by transmission electron microscopy, N(2) adsorption, X-ray photoelectron spectroscopy, and thermal gravimetric analysis. It was demonstrated that the particle size varied in the range of 40-220 nm, and the pore size of particles was centered around 2 nm. The gases produced in the formation process of the particles played key role in the formation of the porous structure. The obtained porous magnetite was used as support to immobilize Au nanoparticles with size less than 2 nm with the assistance of L-cysteine. The as-prepared Fe(3)O(4) particles can effectively catalyze epoxidation of styrene, and the immobilization of Au nanoparticles on the Fe(3)O(4) support significantly improved the activity of the catalyst.     

基于Fe3O4@Au复合纳米粒子标记抗体的电化学免疫方法用于水体中大肠杆菌的检测

合成了Fe₃O₄@Au复合纳米粒子作为辣根过氧化酶标记抗体的载体, 并将该复合纳米粒子标记物应用于电化学放大免疫分析. 将电子媒介体硫堇聚合在玻碳电极表面, 以纳米金作为固定大肠杆菌抗体的基底, 通过辣根过氧化酶催化溶液中H₂O₂产生的电流信号来测定大肠杆菌. 实验结果表明, 该方法对水体中大肠杆菌检测的线性范围为50～1×10⁵ cfu/mL, 检出限为20 cfu/mL. 对过富集后的实际水样进行测定, 该法结果表明, 对水体中大肠杆菌的检测灵敏度达到2 cfu/mL.     

Photocatalytic Synthesis of Gold Nanoparticles Using Preyssler Acid and Their Photocatalytic Activity

Preyssler acid H14[NaP5W30O110] was used as reducing agent and stabilizer for the synthesis of gold nanoparticles by photolysis of Au(III)/Preyssler acid/propan-2-ol solution.Preyssler acid plays both the role of transferring electrons from propan-2-ol to Au(III) and stabilizing the nanoparticles.Propan-2-ol was used as sacrificial reagent for the photoformation of reduced Preyssler acid.Gold nanoparticles (Au NPs) were characterized by UV-Vis spectroscopy,transmission electron microscopy (TEM),and particle size distribution (PSD) measurements.The synthesized Au NPs had a uniform hexagonal morphology and their size was about 17 nm.The catalytic performance of these NPs for photodegradation of methyl orange (MeO) was investigated in aqueous solution.UV-Vis studies showed that Au NPs can catalyze photodegradation of this azo dye.The pseudo-first-order rate constants were also calculated for this reaction.     

单晶Au表面和Au/TiO2（110）模型催化剂表面CO氧化反应机理和活性位

在分子尺度上介绍了Au/TiO2(110)模型催化剂表面和单晶Au表面CO氧化反应机理和活性位、以及H2O的作用.在低温(<320 K), H2O起着促进CO氧化的作用, CO氧化的活性位位于金纳米颗粒与TiO2载体界面(Auδ+–Oδ––Ti)的周边. O2和H2O在金纳米颗粒与TiO2载体界面边缘处反应形成OOH,而形成的OOH使O–O键活化,随后OOH与CO反应生成CO2.300 K时CO2的形成速率受限于O2压力与该反应机理相印证.相反,在高温(>320 K)下,因暴露于CO中而导致催化剂表面重组,在表面形成低配位金原子.低配位的金原子吸附O2,随后O2解离,并在金属金表面氧化CO.