城市道路交通噪声远期统计预测模式

现有城市交通噪声预测方法是建立在单条道路噪声预测基础上的。本文提出的统计预测模式可直接利用城市规划资料、车辆拥有量的发展趋势来预测城市交通噪声平均值、空间分布和暴露在不同声级下的人口数。     

中低速磁悬浮交通噪声研究

使用多通道噪声分析系统,对中低速磁悬浮列车运行时产生的噪声进行信号采集及分析,取得其传播规律、频谱等特性,并与普通轮轨噪声进行对比。研究结果表明,中低速磁悬浮列车运行时相对于普通轮轨噪声较低,就声环境保护角度而言具有较大的优势。     

城市车辆流分布模型及道路交通噪声预报的研究

本文将道路中通行的各种车按其发出的噪声级的高低分成四个等级。提出以每小时900辆的车流量为限,车流将分别服从“泊松”及“正态”分布。对车流较大,服从“正态”分布车流。定量地分析出各等车流量与路边统计噪声级的关系,推导出相应的公式。与他人已做过“泊松”分布一起,构成一套完整的路边声级L_(10)预报表。可以做为评价、预测城市交通噪声之基础。经在北京多条道路的实测验证,与实测值很好符合。     

振动噪声等高图的电驱动桥噪声预测及优化*

在项目开发前期通过优化电驱动桥扭矩特性的设计,可以规避噪声大问题。根据电驱动桥台架在对应扭矩下的振动噪声特性,提出了一套稳定高效的测试流程和分析方法。首先设计了一套完整的试验流程,制定了精准的数据分析方法。然后绘制出能够全面反映电驱动桥振动噪声特性的等高图。最后利用电驱动桥台架的振动噪声等高图,准确评估电驱动桥加速工况下振动噪声风险,为主机厂和电驱动桥零部件企业提供电驱动桥扭矩特性设计前期指导。利用该方法成功识别到某电驱动桥匀速及加速工况下电机及齿轮的啸叫问题。通过优化电驱动桥扭矩特性设计,电机48阶噪声峰值降低了8.5dB(A),确认该方法准确可靠,具备推广应用价值。     

基于改进声线跟踪法的室内交通噪声动态模拟

对碰撞点的有效性判断是传统声线跟踪法的一个重要步骤,在计算复杂的室内空间问题时计算量较大,为解决这一问题采用了一种与空间剖分相结合的改进的声线跟踪法。将该方法与微观交通流仿真和车辆噪声排放模型进行结合,实现了道路交通噪声透过窗户在多连通室内空间传播的动态模拟。最后采用该方法对相同道路和交通流条件下不同建筑朝向的4种布局室内噪声进行动态模拟。分析了室内交通噪声的大小和分布与建筑物布局、窗户的朝向、窗户的形式和面积等因数之间的关系。结果表明:窗户正对道路的房间比窗户侧对道路的房间噪声高4～6 d B(A),房间内等效声级与窗户面积的对数成正比关系。     

公路交通噪声频率特征及等效频率研究

为了确定不同车型在不同行车速度下的噪声频率分布特性及等效频率值,更加准确的对交通噪声的影响进行评估,本文对单车稳态辐射噪声的频率特性进行了现场测定,并对不同类型车辆的频率特性数据进行了分析。结果表明,不同类型车辆车速与频带声压级之间的相关性随频带中心频率的变化而变化。FHWA模型对公路交通噪声中介于500 Hz～2000 Hz频段的噪声有较好的预测效果,而对低于500 Hz和高于2000 Hz的交通噪声的预测精度较差。车辆类型不同,车辆产生噪声的中心频率、声能量集中分布的频率范围以及等效频率均不相同。     

冷却用弯掠轴流风机气动噪声预测与试验分析

采用Navier-Stokes方程和标准k-ε湍流模型,对五种不同结构的弯掠轴流风机A/B/C/D/E进行稳态数值模拟,结合给定的性能要求筛选出B/E风机。以稳态流场为基础,采用大涡模拟(LES)与基于Lighthill声类比的FW-H模型相结合的方法对B/E风机进行非定常计算和气动噪声预测,并将预测结果与试验数据进行了对比验证。分析了以叶轮表面作为噪声源时B/E风机的涡流噪声频谱特性,研究了风机三维非定常内部流场中旋涡分布特性,并探讨了风机旋转区域内部声压级的分布规律。     

城市道路交通噪声烦恼度社会调查

本文以烦恼度为主观反应指标,采用三种5级程度衡量尺度,对西安市内三条主要干道和两类典型交叉口附近区域内的道路交通噪声进行了烦恼度问卷调查。此次调查针对人口统计学因素(性别、年龄、文化程度、身体健康状况)上的个体差异与等级描述词不同的程度尺度可能对道路交通噪声烦恼度调查结果的影响,以及特定路况条件下的噪声烦恼度与不同机动车辆的行驶噪声烦恼度展开了研究。通过对调查数据的分析处理,发现并初步总结出:与选取不同的烦恼度尺度相比,人口统计学因素对调查结果的影响更加显著;人口统计学因素与特定路况条件下的噪声烦恼度及不同机动车辆的行驶噪声烦恼度无明显相关;但不同机动车辆的行驶噪声烦恼度不同,实际研究中需对摩托车噪声加以重视并区别对待。     

公路交通噪声预测模型探讨

对公路交通噪声预测模型进行了分析推导,指出美国联邦公路局FHWA模型为近似表达式,并给出了精确表达式。对FHWA模型与精确表达式在硬地面、软地面、混合地面几种条件下的值进行了比较分析。结果表明,两者在硬地面条件下的形式和计算结果相同;在混合地面,即公路的实际情况下,两者存在差异,差值等于10lg(r1/r0)α。在用于高速公路交通噪声预测计算时,当r0取15m,该差值较小,当r0取7.5m,该差值增大;在一般情况下,r0取15m时的差值为±0.3dB(A),r0取7.5m时的差值为1.2—1.8dB(A),后者约占交通噪声预测值的1.5-4%,是不应忽视的。说明我国在引用FHWA模型时,对参考点距离的更改,会造成用于高速公路交通噪声预测的误差增大。建议我国使用本文推导给出的修订模型。     

亚音主旋翼的噪声预测和声隐身分析

本文介绍了基于FW-H方程的亚音主旋翼噪声预测方法,并在螺桨噪声预测程序基础上发展了主旋翼噪声预测程序。本文采用商用CFD软件FINE／TURBO模拟直升机旋翼流场,为噪声预测程序提供所需要的桨叶表面载荷,并用算例验证了载荷数据的准确性和噪声预测程序的有效性。本文计算和讨论了亚音悬停条件下的辐射噪声,并重点分析了不同形状桨叶对辐射噪声的影响,结果表明采用合理的薄翼型叶尖、尖削叶尖及线性扭转桨叶都可以降低辐射噪声,为通过改变桨叶形状降低旋翼辐射噪声提供了合理途径。     

Prediction of noise changes due to traffic speed control

The effects of vehicle speed variation on road traffic noise are analyzed. The steady speed motion is replaced by deceleration, cruise, and acceleration. Because of a relatively loud acceleration noise, such a speed variation results not only in the noise decrease zones, but in the noise increase zones as well. The location of these zones depends slightly upon the ground covering (grass, concrete, etc.). Conversely, their boundaries change dramatically with the parameters describing noise emission during deceleration, cruise, and acceleration. For example, the Japanese and Polish models of noise emission have been applied. The critical length L(*) of the cruise segment of the road is introduced: for L>L(*) the sound energy decline (due to speed reduction) compensates the sound energy growth (due to acceleration). The results obtained could be useful for road administrators.     

Prediction of the attenuation of road traffic noise with distance

A method is described of calculating the sound pressure level received from single, representative light and heavy vehicles after propagation over terrain composed of various combinations of hard ground and grass-land. These results are then used to derive correction contours for the attenuation with distance of the L_eq level received from streams of each class of vehicle. The results apply to conditions where the boundary between the soft and hard areas is parallel to the traffic stream and the soft ground is on the receiver side. Various positions of the boundary are considered. A simple prediction method for L_eq is developed, incorporating the distance corrections. Similar calculations are carried out for the attenuation with distance of the L₁₀ noise index for a representative stream of vehicles. Based on these results simple prediction equations for the excess attenuation are proposed in terms of the receiver position and the proportion of soft ground below the propagation path.     

Motorway noise modelling based on perpendicular propagation analysis of traffic noise

A model for motorway traffic noise has been obtained from measurements along the the Bangkok-Chonburi motorway. The model’s parameters include traffic volume and combination, the average spot speed of each type of vehicle and the physical conditions of the motorway in terms of right-of-way width, number of lanes, lane width, shoulder width, and median width for both of the main carriageways and frontage roads. The noise level that is generated by each type of vehicle has been analyzed according to the propagation in the direction perpendicular to the center line of motorway’s carriageway. The total traffic noise is then analyzed from traffic volume of all vehicle types on both sides of carriageways and frontage roads. The basic noise levels used in the motorway traffic noise model are modified according to the effective ground effect along the propagation path. The final result of this study is that a motorway traffic noise model based on the perpendicular propagation analysis technique performs well in a statistical goodness-of-fit test against the field data, and therefore, can be used effectively in traffic noise prediction for related or similar motorway projects.     

A method of traffic noise prognosis

This paper describes a simple method for the calculation of changes in noise levels generated by the vehicle population of a country as a whole in future time related to present population. The changes of the total number of vehicles, the introduction of quieter vehicles and the condition of wear of the running stock are taken into account in the model and the change in L_eq level is used as the output parameter. The calculated changes in L_eq values are about the same as those of L₁₀. The application examples of the model show that this simple method seems to be helpful for decision makers. The examples also allow conclusions for noise control strategy to be developed.     

Prediction of aerodynamic noise reduction by using open-cell metal foam

As the speed of high-speed train (HST) increases continuously, aerodynamic noise has become more remarkable compared with the wheel/rail noise, which affects the inhabited environment along the railway and the riding comfort. This paper preliminarily investigates the feasibility of using open-cell metal foam covering layer to reduce the low Mach number aerodynamic noise generated by the flow around a circular cylinder which is the typical section of pantographs. The aerodynamic noises radiated from the circular cylinder with and without metal foam are calculated. The hybrid method combining two-dimensional large eddy simulation (LES) with Ffowcs Williams–Hawkings (FW–H) equation is employed. The calculated Strouhal number, time-averaged drag coefficient, base pressure and overall sound pressure level agree well with some available experimental data. Then, the influences of metal foam porosity, pore density, thickness of covering layer and the speed of train on the aerodynamic noise and the aerodynamic forces are investigated, and some detailed comparisons of flow field are made. The numerical results indicate that as a passive scheme, the open-cell metal foam with high porosity can modify the flow, adjust the vortex shedding frequency and regularize the wake, leading to a significant reduction of aerodynamic noise. The results are expected to provide useful information for the control of aerodynamic noise using this new material.     

Pressure Leq and multiple noise sources: A comparison of exposure-response relationships for railway noise and road traffic noise

Exposure-response relationships vary with different noise sources when conventional L_eq is used as the noise exposure measure. Further, reported annoyance to multiple noise source environments can be higher than predicted by conventional L_eq. Pressure L_eq is proposed as a superior unified noise index and some evidence is presented in support of this proposal.     

A traffic noise prediction method based on vehicle composition using genetic algorithms

The effect of traffic composition on the noise pollution has been investigated in a small city Erzurum, located in eastern Turkey, where the population is about 400,000. Manual noise measurements and vehicle counts were performed at the four heaviest traffic points in the city for a period of 12 h. Using the information on vehicle composition and the maximum legal noise emissions of each type of vehicles, two prediction models based on genetic algorithms have been developed that can be used as tools for in-city traffic flow redesign. The models have been validated against some of the noise data. Measured traffic noise levels have been compared with predictions using the new models and some existing ones and a relatively good agreement has been obtained between them.     

The prediction of traffic noise using a scale model

This paper describes the development of means of using a scale model of a road and its surrounding urban environment to predict L_eq, L₁₀ and other measures of traffic noise. The model described is that of the Centre Scientifique et Technique du Batiment, Grenoble, France. The problems involved in the development include allowance for relative sound absorption between real life and the model situation, the constraints on the accuracy of the results due to noise source variations on the model and the effects of the finite size of the model.     

利用自相关函数和双耳自相关函数分析对交通噪声特征参量的提取~

对实地双通道测量获得的道路交通噪声和铁路噪声信号样本进行了自相关函数和双耳自相关函数(Interaural CrossCorrelation Function)的分析。进而通过对噪声样本时间因子和空间因子的相关性分析、主成分分析和主观评价实验,得到了3个铁路噪声源特征参量物理因子和4个道路交通噪声源特征参量物理因子。发现与传统的声压级测量相比,表征声音信号时间特性和空间特性的这7个物理量可以更全面、准确地表征交通噪声的特性。在对道路噪声进行测量或分析时,掌握与声源视觉宽度和音调感相对应的物理因子以及双耳时延和初始能量,就可获悉与人的主观评价相一致的道路交通噪声特征信息;对铁路噪声而言,掌握与声源视觉宽度相对应的物理因子以及双耳时延和声音的重复性特征,就可以得到与入主观评价相一致的铁路噪声特征信息。综合道路噪声特征参量和铁路噪声特征参量可以发现,双耳时延和与声源视觉宽度相对应的物理因子是与人的主观反应最为一致的主成分指标,说明噪声中决定人的评价的最主要的因素是代表空间特征的信号因子。     

Investigating generation mechanisms of tyre/road noise by speed exponent analysis

The purpose of this study is to clarify the influence of air-pumping related noise sources on typical tyre/road noise. The aim is to increase the understanding of noise generation mechanisms and catalyse the development of existing tyre/road noise simulation tools. The speed dependency of measured and simulated tyre/road noise is analysed and the results show that a large part of the noise can be explained by a high speed exponent traditionally connected with air-pumping mechanisms. Surprisingly, this is also the case for rough road surfaces which are expected to mainly generate noise by tyre vibrations. It is also found that vehicle wind noise may have a strong influence on the pass-by noise and care must be taken when analysing measurement data of quiet tyre/road combinations. Even simulated tyre/road noise shows higher speed exponents than what is anticipated without the inclusion of any type of air-pumping mechanism in the model. It is concluded that it is unfeasible to separate noise created by tyre vibrations from noise created by air-pumping with a speed exponent analysis due to the overlap in the speed exponents connected with the different generation mechanisms.