尿苷二磷酸葡萄糖的合成研究进展

介绍了化学和酶法合成尿苷二磷酸葡萄糖(UDPG)及酶法合成13C标记UDPG的方法的优缺点及研究进展.     

固相萃取/超高效液相色谱法测定龙胆泻肝丸中栀子苷、龙胆苦苷与黄芩苷

建立了一种快速测定龙胆泻肝丸中栀子苷、龙胆苦苷和黄芩苷3种有效成分的超高效液相色谱方法。样品经50%甲醇提取,C18固相萃取(SPE)小柱净化后,采用Ultimate XB-C18色谱柱(4.6 mm×50 mm,1.8μm)进行分离,以乙腈-0.1%磷酸溶液为流动相进行梯度洗脱。考察了不同规格色谱柱、流动相梯度比例、进样体积、柱温和流速对分离效果的影响,并对SPE柱流出液的平衡体积进一步考察,在最佳分析条件下进行液相色谱分析,该方法显示了良好的线性关系(r≥0.999 8),其定量下限(LOQ)为0.24～0.44 mg/L,加标回收率为95%～99%。该方法快速、准确,可满足实际检测需要。     

离子色谱法测定乳糖玉米淀粉共处理物中有关物质

建立离子色谱法测定乳糖玉米淀粉共处理物中的有关物质.采用离子色谱法(安培检测器)进行测定,色谱柱为CarPac PA20分析柱,流动相为水–氢氧化钠溶液(0.25 mol/L)–乙酸钠溶液(0.25 mol/L),梯度洗脱,流量为0.4 mL/min,柱温为30℃.蔗糖、葡萄糖、半乳糖、乳糖的质量浓度在0.05～2μg...     

女贞子中红景天苷的HPLC制备分离

研究了制备型高效液相色谱分离纯化女贞子中红景天苷的方法。制备色谱的参数为:色谱柱为C18柱(50 mm×200 mm,5μm),流动相为甲醇-水(体积比为7.5∶92.5),流速100 mL·min-1,二级管阵列检测器在278 nm检测,进样体积为2.2 mL。在18 min的运行时间内,红景天苷与干扰成分得到很好的分离,经HPLC检测纯度均达到98%以上。此方法具有快速高效、分离组分纯度高的特点,可用于制备红景天苷。     

烷基酚聚氧乙烯醚在不同液相色谱分离模式中的分离研究

考察了烷基酚聚氧乙烯醚在反相色谱、正相键合色谱、硅胶吸附色谱、体积排阻色谱4种不同液相色谱分离模式中的分离效果,分别采用Kromasil C_(18)(250 mm× 4.6 mm,5 μm)、Agilent ZORBAX NH2(250 mm× 4.6 mm,5 μm)、Waters Spherisorb S3W(150 mm×2.0 mm,3 μm)和Shodex MSpak GF-310 2D(150 mm×2.0 mm,5 μm)色谱柱,以225 nm为紫外检测波长,对不同液相色谱分离模式的流动相组成、梯度洗脱条件、柱温、流速等进行了优化,并对烷基酚聚氧乙烯醚在不同液相色谱分离模式中的保留机理进行了初步探讨.结果表明,正相键合色谱实现了烷基酚聚氧乙烯醚的最佳分离;硅胶吸附色谱和体积排阻色谱的分离效果较正相键合色谱稍差.     

HPLC测定河套大黄中的土大黄苷含量

从河套大黄中分离纯化出活性成分土大黄苷,作为自制的标准品,利用KromasilTM C(18)(250 mm×4.6 mm I.d.,5μm)反相色谱柱,以V(甲醇):V(乙腈):V(水)=35:5:60为流动相,以320mm为检测波长,对河套大黄中土大黄苷进行测定.土大黄苷在0.427～4.190μg范围内与峰面积呈良好线性关系(r=0.9994),平均回收率为99.12%.该方法为河套大黄的质量控制奠定了基础.     

高效液相色谱法测定甜叶菊糖中的甜菊苷和莱鲍迪苷A

建立甜叶菊糖中甜菊苷(简称为ST)和莱鲍迪苷A(简称为RA)的HPLC定量分析方法.色谱分离采用Kromasil NH2柱(250 mm×4.6 mm i.d.,5 μm),以V(乙腈):V(水)=75:25为流动相,采用质谱检测器鉴定甜叶菊糖中主要的成分.ST和RA质量浓度分别为9.0～287.6 mg/L和3.9～126.1 mg/L时线性关系良好,两者平均回收率分别为98.61%和97.40%,RSD分别为2.3%和1.3%(n=5).本实验还利用经典的Eschweiler-clark甲基化反应将氨基柱的伯胺转变为叔胺,发现上述溶质保留减小,同时分离选择性减小,说明氨基与糖苷类化合物的氢键作用和偶极-偶极作用对分离有重要贡献.     

大孔阴离子树脂分离纯化微生物转化液中5-氟尿苷的研究

探寻从微生物转化液中分离纯化5-氟尿苷(5-FUR)的工艺条件。先后尝试了大孔吸附树脂、大孔弱碱性阴离子交换树脂以及硅胶柱色谱的分离方法,首先利用大孔弱碱性阴离子交换树脂吸附,然后用1mol/L NaCl动态洗脱得到含量较高的两种含氟化合物,最终通过硅胶柱色谱,采用正己烷-乙酸乙酯(含10%醋酸)为流动相进行洗脱,得到了纯度为100%的纯品。在目标化合物和杂质理化性质极其相似,含量极其悬殊的条件下,成功去除含量极高的杂质,实现了5-FUR的分离纯化,圆满地达到了预期的目的。     

二氢麦角碱在极性嵌入反相色谱固定相上的分离行为

二氢麦角碱的4种组分具有不同的药效特性,需适当的分析方法对其在不同剂型药品中的含量进行分析.传统液相色谱方法使用强碱性流动相,严重腐蚀硅胶基质色谱填料,影响色谱柱寿命.合成了极性嵌入反相固定相--C18酰胺固定相,并在中性流动相条件下分离4种组分.考察了流动相组成和pH对二氢麦角碱在C18酰胺固定相上保留行为的影响.在150 mm×4.6 mm I.D.的C18酰胺色谱柱上,流动相为乙腈-20 mmol/L Na2HPO4(30:70,V/V,pH 7.0)的条件下实现了4种组分的基线分离.与传统方法相比,极性嵌入反相固定相可以有效的改善碱性化合物的分离特性和大幅度地延长色谱柱的使用寿命.     

高效液相色谱法测定辣椒中的辣椒碱和二氢辣椒碱

建立了高效液相色谱法(HPLC)测定辣椒中辣椒碱、二氢辣椒碱的检测方法.实验考察了仪器条件、不同流动相体系、流动相配比、柱温、流速等因素对分离的影响.确定了最佳色谱条件为ZORBAX SB-C18色谱柱(250mm×4.6 mm,5μm);二极管阵列检测器,辣椒碱、二氢辣椒碱的最佳检测波长为280 nm;色谱柱温度为2...     

新型芳基修饰的尿苷型荧光探针的合成及其性能

4-氟苯乙酮经二氧化硒氧化得到4-氟苯甲酰甲酸(1); 1与盐酸氨基脲在碱性条件下经环合反应制得5-(4-氟苯基)-6-氮杂嘧啶(2); 2与1-乙酰氧基-2,3,5-三苯甲酰氧基-1-β-D-呋喃核糖在无水乙腈中反应得2′,3′,5′-三苯甲酰氧基-5-(4-氟苯基)-6-氮杂尿苷(3); 3在甲醇中水解合成了一种新型荧光核苷探针--5-(4-氟苯基)-6-氮杂尿苷(4),其结构经¹H NMR, ¹³C NMR和MS(ESI)表征。并研究了4的性能。结果表明：4在水中的量子产率高达0.81,对极性变化敏感;4可选择性识别Pd²⁺,在5.0×10^-7~5.0×10^-6 mol·L^-1能定量检测Pd²⁺。     

Excess-Electron Attachment and Ionization of Aqueous Uridine Monophosphate Anion

We applied quantum mechanics/classical mechanics simulations to study excess-electron attachment and ionization of uridine monophosphate anion (dUMP\begin{document}$^-$\end{document}) in explicit aqueous solutions. We calculated vertical electron affinities (VEAs), adiabatic electron affinities (AEAs), vertical detachment energies (VDEs), vertical ionization energies (VIEs), and adiabatic ionization energies (AIEs) of the 40 structures obtained from molecular dynamic trajectory. The excess-electron and hole distributions were analyzed in electron attachment and ionization of aqueous dUMP\begin{document}$^-$\end{document}. The converged mean VEA (-0.31 eV) and AEA (2.13 eV) suggest that excess-electron can easily attach to dUMP\begin{document}$^-$\end{document}. The mean vertical (-0.50 e) and adiabatic (-0.62 e) excess-electron on uracil reveal that main excess-electrons are localized on nucleobases at the most snapshots. The distributions at several special snapshots demonstrate the excess-electron delocalization over nucleobases/ribose or ribose/phosphate group after the structural relaxations of dUMP\begin{document}$^{2-}$\end{document} dianion. The VDE value (2.78 eV) indicates that dUMP\begin{document}$^{2-}$\end{document} dianion could be very stable. Moreover, the mean VIE is 8.13 eV which is in agreement with the previous calculation using solvation model. The hole distributions on uracil suggest that the nucleobases are easily ionized after the irradiation of high-energy rays. In vertical ionizations, the holes would be delocalized over uracil and ribose at several snapshots. Observing the adiabatic hole distributions, it can be found that electrons on phosphate group and holes on nucleobases can be transferred to ribose at the special snapshots in the structural relaxation of neutral species.     

微波辅助快速制备核-壳型尿苷印迹聚合物及其在线富集应用研究

采用微波辅助加热,以尿苷为模板分子,丙烯酰胺(AA)为功能单体,乙二醇二甲基丙烯酸酯(EGDMA)为交联剂,快速制备尿苷印迹聚合物,聚合时间大大缩短,仅为传统加热的1/8.采用红外光谱和扫描电镜对印迹聚合物进行表征,结果表明二氧化硅表面成功包覆尿苷印迹壳层;该印迹聚合物颗粒分散均匀,印迹壳层厚度约为100 nm.将该印...     

Synthesis of 5‐Radioiodoarabinosyl Uridine Analog for Probing the HSV‐1 Thymidine Kinase Gene

Tumor cells transduced with herpes simplex virus thymidine kinase gene have been intensively applied to the field of positron emission tomography via imaging of its substrate. As a pilot synthesis approach, a facile preparation of 5‐[¹²⁵I] iodoarabinosyl uridine starting from commercially available uridine is reported herein.     

Extraction chromatographic study of aluminium(III) and mutual separation of aluminium(III), gallium(III), indium(III) and thallium(III) with N-n-octylaniline

A selective method has been developed for extraction chromatographic studies of aluminium(III) and its separation from several metal ions with a chromatographic column containing N-n-octylaniline (liquid anion exchanger) coated on silanized silica gel as a stationary phase. The aluminium(III) was quantitatively extracted with the 0.065 mol/L N-n-octylaninine from 0.013 to 0.05 mol/L sodium succinate at a flow rate of 1.0 mL/min. The extracted metal ion has been recovered by eluting with 25.0 mL of 0.05 mol/L hydrochloric acid and estimated spectrophotometrically with aurintricarboxylic acid. The effects of the acid concentration, the reagent concentration, the flow rate and the eluting agents have been investigated. The log-log plots of distribution coefficient (KdAl(III)) versus N-n-octylaniline concentrationin 0.005 and 0.007 mol/L sodium succinate gave theslopes 0.5 and 0.7 respectively and showed theprobable composition of theextracted species was 1:1 (metal to amine ratio) and the nature of extracted species is [RR''NH2+ Al succinate2-] org. .The extraction of aluminium(III) was carried out in the presence of various ions to ascertain the tolerance limit of individual ions. Aluminium(III) has been separated from multicomponent mixtures, pharmaceutical samples and synthetic mixtures corresponding to alloys. A scheme for mutual separation of aluminium(III), indium(III), gallium(III) and thallium(III) has been developed by using suitable masking agents. The method is fast, accurate and precise.     

HCOO在Cu(110)、Ag(110)和Au(110)表面的吸附

采用密度泛函理论(DFT)以及广义梯度近似方法(GGA)计算了甲酸根(HCOO)在Cu(110)、Ag(110)和Au(110)表面的吸附. 计算结果表明, 短桥位是最稳定的吸附位置, 计算的几何参数与以前的实验和计算结果吻合. 吸附热顺序为Cu(110)(-116 kJ·mol-1)>Ag(110)(-57 kJ·mol-1)>Au(110)(-27 kJ·mol-1), 与实验上甲酸根的分解温度相一致. 电子态密度分析表明, 吸附热顺序可以用吸附分子与金属d-带之间的Pauli 排斥来关联, 即排斥作用越大, 吸附越弱. 另外还从计算的吸附热数据以及实验上HCOO的分解温度估算了反应CO2+1/2H2→HCOO的活化能, 其大小顺序为Au(110)>Ag(110)>Cu(110).     

Synthesis of Some Novel Class of Bis(isoxazoline) and Bis(aziridine) Derivatives

Synthesis of some new bis(isoxazoline) derivatives has been described from terepthaldehyde derived bis(nitrones) using microwave irradiation via 1,3‐dipolar cycloaddition reaction. Bis(isoxazoline) derivatives in turn successfully converted into new bis(aziridine) derivatives via Baldwin rearrangement. Simple reaction methodology, non involvement of catalysts, and good to excellent yields are the important features noticed in this synthesis.     

Spectrophotometric study of Cd(II), Pb(II), Hg(II) and Zn(II) complexes with 5,10,15,20-tetrakis(4-carboxylphenyl)porphyrin

The reaction of 5,10,15,20-tetrakis(4-carboxylphenyl)porphyrin (TCPP) with Cd(II), Pb(II), Hg(II) and Zn(II) was studied spectrophotometrically and kinetics, equilibrium constants as well as photodecomposition of complexes were determined. It was verified that these metal ions with large radius accelerate the incorporation reaction of zinc into TCPP. On the basis of the mechanism and kinetics of this reaction, a sensitive method for the spectrophotometric determination of trace amounts of Zn(II) has been developed. The molar absorptivity of examined Zn-TCPP complex and Sandell's sensitivity at 423 nm were 3.5×10⁵ M⁻¹ cm⁻¹ and 18.3 ng cm⁻². The detection limit for the recommended procedure was 1.4×10⁻⁹ M (0.9 ng ml⁻¹) and precision in range 20-100 ng ml⁻¹ not exceeds 2.7% RSD. The proposed method applied for zinc determination in natural waters and nutritional supplement was compared with AAS results and declared value.     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.