Pressure based finite volume method for calculation of compressible viscous gas flows

A pressure based, iterative finite volume method is developed for calculation of compressible, viscous, heat conductive gas flows at all speeds. The method does not need the use of under-relaxation coefficient in order to ensure a convergence of the iterative process. The method is derived from a general form of system of equations describing the motion of compressible, viscous gas. An emphasis is done on the calculation of gaseous microfluidic problems. A fast transient process of gas wave propagation in a two-dimensional microchannel is used as a benchmark problem. The results obtained by using the new method are compared with the numerical solution obtained by using SIMPLE (iterative) and PISO (non-iterative) methods. It is shown that the new iterative method is faster than SIMPLE. For the considered problem the new method is slightly faster than PISO as well. Calculated are also some typical microfluidic subsonic and supersonic flows, and the Rayleigh–Bénard convection of a rarefied gas in continuum limit. The numerical results are compared with other analytical and numerical solutions.     

基于Gross-Pitaevskii能量泛函求解谐振势阱中玻色凝聚气体基态波函数

基于Gross-Pitaevskii(G-P)平均场能量泛函和变分方法，对囚禁在谐振势阱中的玻色凝聚气体，在T=0K时的基态波函数提出一种新解法.运用这一方法能得到基态波函数的解析表达式，求解出系统的化学势与凝聚原子数的关系等.其结果与Edwards和Dalfovo等人直接数值求解G-P方程所得到的结果相一致，并在Na_s/a1大原子数N的极限条件下，与托马斯-费米近似模型的结论也趋向一致.该方法计算简单，而且能够进行解析处理. 关键词： 玻色凝聚气体 G-P泛函 谐振势阱 基态波函数     

近红外漫反射光谱法快速测定天然纤维素清洁浆料α-纤维素含量

针对天然纤维素清洁制浆新型连续生产工艺,提出了采用近红外漫反射光谱测定天然纤维素(棉、木浆粕)清洁浆料中α-纤维素含量。收集了142个天然纤维素清洁浆料样品,采用GB/T 9107—1999方法(化学分析方法)测定其α-纤维素含量。通过粉碎预处理提高样品的均匀性,继而压入旋转杯采集光谱。采用簇类独立软模式(SIMCA)方法建立了有效的棉浆粕和木浆粕的分类模型,模型识别率达到100%。基于偏最小二乘(PLS)法分别建立的全部样品以及分类棉、木浆粕的α-纤维素含量定量校正模型相关系数分别为0.954,0.911和0.839,SEP分别为2.4%,1.2%和1.6%,模型预测精密度与GB方法的允差接近,表明该方法是可行的,且操作简单,分析速度快,对提高天然纤维素清洁浆料α-纤维素含量分析效率和指导其连续生产具有积极意义。     

New spectroscopic method for the determination of optical rotatory dispersion

A new spectroscopic methodology is proposed to measure optical rotatory dispersion(ORD)of optically active media.ORD is obtained from a three-step phase shifting algorithm using transmission spectra taken at three independent probing angles.Optical rotation angles of four sugar solutions are investigated.The results obtained by using the new method show excellent agreement with the reference data,indicating the new method can be used as a reliable way for studying ORD of optically active media.     

DSMC方法的压力边界条件实现

提出了一种实现DSMC压力边界条件的新方法,新方法不仅可以避免传统"通量法"造成的计算发散问题,又较之"入口平均法"有更快的收敛速度.使用这种方法,对不同压差驱动下等壁温微通道内的气体流动进行了模拟,并与传统的基于连续介质假设的滑移理论所得结果进行了比较.     

尾翼型爆炸成型弹丸的数值模拟及实验研究

 在药型罩上粘附铝隔板是一种新的形成尾翼型爆炸成型弹丸（Explosively Formed Projectile,EFP）的实验方法。通过实验和数值模拟对该方法进行了分析,探讨了形成尾翼的机理。利用有限元分析软件LS-DYNA,对大锥角型、球缺型和弧锥结合型3种不同药型罩在采用新方法时形成的尾翼型EFP进行了三维数值模拟分析,并将模拟结果与实验结果进行对比。研究结果表明：3种药型罩均能形成比较明显的尾翼,数值计算结果与实验结果较吻合。该研究为设计尾翼型EFP提供了一种新的参考方法。     

屏蔽理论对LiⅠ等电子序列离子基组态能量的计算方法研究

在屏蔽理论和多体微扰理论的基础上,文中提出了一种新的计算等电子序列离子基组态能量的方法,用该方法和作者设计的FORTRAN程序,计算了LiⅠ等电子序列离子 (3≤Z≤20)基组态能量,计算结果与已有实验结果十分接近,表明该方法对低Z原子体系基组态能量的计算是可行的.     

FFT-BP神经网络模型对车载γ能谱辐射剂量率的预测分析

为了实现车载γ谱仪巡测系统对辐射剂量率的准确测定，提出基于快速傅里叶变换(FFT)本底扣除法的改进型BP神经网络模型(FFT-BP神经网络模型)。实验采用γ射线能谱分析法，对不同间距处的137Cs放射源进行车载γ能谱测试，将得到的谱数据通过快速傅里叶变换(FFT)扣除本底，获得新的谱线数据。应用FFT-BP神经网络模型对未知剂量的车载γ谱线作辐射剂量率的定量预测，将预测结果同3个函数模型的拟合结果比较，验证FFT-BP神经网络模型的预测效果。结果表明，FFT扣除法能较好的削弱散射本底对γ谱线的影响，能有效的降低谱线本底。通过新谱线获得的特征峰面积和净谱线面积与辐射剂量率的相关系数均为0.99(p<0.05)，相关性显著。模型拟合分析过程中，FFT-BP神经网络模型表现出较强的学习泛化能力，预测较理想，相对误差和累计误差分别低于0.6%和9%，效果明显优于数学模型和γ能谱全能峰法，可显著降低γ能谱分析辐射剂量率的误差，且能有效提升工作效率。因此，FFT-BP神经网络模型适用于γ能谱辐射剂量的预测分析，为车载γ谱仪巡测系统测量辐射剂量提供了一种新型有效的分析方法。     

Recursion-transform method and potential formulae of the m × n cobweb and fan networks

In this paper, we made a new breakthrough, which proposes a new recursion–transform(RT) method with potential parameters to evaluate the nodal potential in arbitrary resistor networks. For the first time, we found the exact potential formulae of arbitrary m × n cobweb and fan networks by the RT method, and the potential formulae of infinite and semi-infinite networks are derived. As applications, a series of interesting corollaries of potential formulae are given by using the general formula, the equivalent resistance formula is deduced by using the potential formula, and we find a new trigonometric identity by comparing two equivalence results with different forms.     

A fourier optics method for the simulation of measurement-volume-effect by the slit constraint

A new method is introduced to analyze the accuracy of phase-Doppler anemometry (PDA) for sizing large particles in two-phase flows. The method is based on Fourier optics theory (FOT) and geometrical optics theory (GOT) to calculate the intensity ratio of refractive and reflective light scattered by a sphere under a slit constraint. To examine the accuracy in calculating the light intensity, the results from the GOT method were compared with those of the direct simulation based on the generalized Lorenz-Mie theory (GLMT). This newly developed FOT/GOT method also predicts the results of phase jump due to the slit constraint. The performance of dual-mode phase-Doppler anemometry can also be simulated by this method.     

安乃近测定新方法的研究

本文基于安乃近将Ｆｅ３＋还原为Ｆｅ２＋、新生的Ｆｅ２＋与α,α′－联吡啶形成桔红色配合物,提出了分光光度法测定药物中安乃近的新方法。安乃近浓度在０～１４μｇ／ｍＬ范围服从比耳定律,线性相关系数ｒ为０．９９９８,其测定的表观摩尔吸光系数ε为２．２９×１０４Ｌｍｏｌ－１ｃｍ－１。     

卡托普利测定新方法的研究

基于卡托普利将Ｃｏ＾２＋的为Ｃｕ,新生的Ｃｕ可一新铜试剂形成黄色络合物,提出了间接分光度法法测定药物中卡托利析新方法。在ＰＨ３－８内,卡托普利浓度在０－２８μｇ／ｍＬ内有从比耳定律,测定的表观摩尔吸光系数ε为８．１３×１０＾３Ｌ·ｍｏｌ＾－１·ｃｍ＾－１。方法简便、快速,用地药物中卡托普利的测定,结果与钨蓝比色法一致。     

Extraction current transients: new method of study of charge transport in microcrystalline silicon

The transport properties of microcrystalline silicon, namely, mobility and conductivity, are investigated by a new method, for which the simple theory as well as numerical modeling is presented. The basic idea of the new method is verified on amorphous hydrogenated silicon by comparison with the widely used time-of-flight method. Contrary to time of flight, the new method can be used even for relatively conductive materials. Preliminary results on microcrystalline silicon clearly indicate the critical role of amorphouslike tissue in transport in microcrystalline silicon.     

直射太阳光差分吸收光谱反演NO2整层垂直柱浓度

在直射太阳光差分吸收光谱技术(DS-DOAS)中,通常采用测量期间较干净大气条件下太阳天顶角最小时的测量谱作为参考谱反演整层垂直柱浓度(VCD)。由于参考谱中依然含有未知的NO2吸收结构,因此得到的是VCD的相对值。该文将大气外层高精度太阳夫琅禾费标准光谱与仪器函数卷积后作为参考谱,避免了参考谱中含有NO2的吸收结构引入的误差。通过研究3月7日用此新方法获得的斜柱浓度(SCD)与通常方法获得的差分斜柱浓度(dSCD)的比较,新方法反演SCD的误差小于1.6×1016 molecules.cm-2;通常方法反演SCD的误差在4.25×1016 molecules.cm-2附近,采用新方法误差减少了62%以上。最后将DS-DOAS测量的NO2整层VCD与多轴差分吸收光谱技术(MAX-DOAS)测得的NO2对流层VCD进行了对比,结果表明新方法可以有效的改进通常方法计算VCD的误差。     

A New Method of Eliminating Chirp using Normal Dispersion Fiber

l.IntroductionItiswellknownthatnormaldiSpersionOPticalfibetcanbeusedtoeliminatethechirpofnegative-chirPCdpulses[l1.Inthisway,wecanusenormaldisPersionfibertocompressthepulsewidth,butitdoesnotaffectthe8PeCtraloutPutenveloPe[2~4].BeCausethesolitonPeriodisindirectproportiontothePUlsewidth,thenarrowerth6pulsewidth,the8horterthesolitonPeriodis.SowecanseethatwiththenarrowingofPulsewidth,thesolitonPeriodwiIlbeshortenedaswell,andtheamP1ificationPeriodwillalsobeshortened.ThuswewillnecdmoreEDFA…     

Development and validation of a new LBM-MRT hybrid model with enthalpy formulation for melting with natural convection

This article presents a new model to simulate melting with natural convection of a phase change material. For the phase change problem, the enthalpy formulation is used. Energy equation is solved by a finite difference method, whereas the fluid flow is solved by the multiple relaxation time (MRT) lattice Boltzmann method. The model is first verified and validated using the data from the literature. Then, the model is applied to a tall brick filled with a fatty acid eutectic mixture and the results are presented. The main results are (1) the spatial convergence rate is of second order, (2) the new model is validated against data from the literature and (3) the natural convection plays an important role in the melting process of the fatty acid mixture considered in our work.     

利用神经网络提高编码器精度的方法

介绍了编码器误差的构成及特点，针对系统误差的分布规律与特点提出了基于神经网络的误差修正方法。采用非线性逼近精度较高的径向基函数神经网络，以采样点的角度值作为网络的输人样本，以高精度检测编码器的检测值作为学习目标建立了误差修正模型。实验结果表明，采用此种方法可将编码器的精度提高至原来的3倍以上，可有效地改善编码器的系统精度。     

Automatic Deformation Analysis in Electronic Speckle Pattern Interferometry Using One Speckle Interferogram of Deformed Object

We propose a new fringe analysis method that uses only one speckle interferogram of a deformed object to obtain phase change distribution by deformation. This method uses cos^-1 operations to extract absolute, not signed, values of new phase after deformation. Considering the phase changes in a small local area, true phase changes retain almost the same value by assuming a continuous deformation in the area. This retention determines the sign of the new phase. From the new phase and the initial phase, the phase change distribution by the deformation can be obtained. Experimental results show the usefulness of this method.     

A new proof of the positive energy theorem

A new proof is given of the positive energy theorem of classical general relativity. Also, a new proof is given that there are no asymptotically Euclidean gravitational instantons. (These theorems have been proved previously, by a different method, by Schoen and Yau.) The relevance of these results to the stability of Minkowski space is discussed.Research partially supported by NSF Grant PHY78-01221