Captopril Electrochemical Oxidation on Fluorine‐Doped SnO2 Electrodes and Their Determination in Pharmaceutical Preparations

A novel application of fluorine‐doped tin oxide (FTO) electrodes is reported in the present work. To this end, the captopril electrochemical oxidation mechanism on FTO electrodes at various pH and its determination in pharmaceutical preparations was investigated. Captopril oxidation on FTO proceeds at pH between 2.0 and 4.0. The study revealed that interferences for captopril determination in pharmaceutical samples was totally suppressed using these electrode materials. Voltammetric survey showed an anodic peak at about 0.375 V (Ag|AgCl) for captopril oxidation, that takes place through an EC process at pH interval 2.0–4.0. The investigation demonstrated that captopril oxidation occurs through protonated species and these electroactive species interact by adsorption on FTO electrodes, with a large heterogeneous rate constant and a mechanism involving 1H⁺/1e^? in the global reaction. Moreover, a captopril sensor based upon FTO electrodes, with a linear range miliMolar, is proposed. These electrodes are promising candidates for the efficient electrochemical determination of captopril in pharmaceutical preparations.     

Carbon nanofiber vs. carbon microparticles as modifiers of glassy carbon and gold electrodes applied in electrochemical sensing of NADH

Carbon materials (CMs), such as carbon nanotubes (CNTs), carbon nanofibers (CNFs), and carbon microparticles (CMPs) are used as doping materials for electrochemical sensors. The efficiency of these materials (either before or after acidic treatments) while being used as electrocatalysts in electrochemical sensors is discussed for β-nicotinamide adenine dinucleotide (NADH) detection using cyclic voltammetry (CV). The sensitivity of the electrodes (glassy carbon (GC) and gold (Au)) modified with both treated and untreated materials have been deeply studied. The response efficiencies of the GC and Au electrodes modified with CNF and CMP, using dimethylformamide (DMF) as dispersing agent are significantly different due to the peculiar physical and chemical characteristics of each doping material. Several differences between the electrocatalytic activities of CMs modified electrodes upon NADH oxidation have been observed. The CNF film promotes better the electron transfer of NADH minimizing the oxidation potential at +0.352 V. Moreover higher currents for the NADH oxidation peak have been observed for these electrodes. The shown differences in the electrochemical reactivities of CNF and CMP modified electrodes should be with interest for future applications in biosensors.     

Unsupported palladium nanoparticles for ethanol cyclic voltammetric sensing in alkaline media

Carbon-supported palladium nanostructures have had a recent rise in their use for ethanol oxidation applications. In this work, we present the use of unsupported palladium nanoparticles (PdNPs), synthesized by sodium borohydride chemical reduction method, for ethanol electrochemical sensing. The unsupported PdNPs were studied for ethanol oxidation in alkaline media by cyclic voltammetry, and additionally were characterized using transmission electron microscopy, and x-ray photoelectron spectroscopy. The performance of unsupported PdNP-modified glassy carbon electrodes for the electrochemical ethanol oxidation in 1.0 M potassium hydroxide (KOH) solution was studied by cyclic voltammetry. These electrochemical results demonstrated that the unsupported PdNPs have very promising catalytic activity towards the oxidation of ethanol in alkaline media with good detection performance in the concentration range of 2304 to 288 ppm (i.e., 50.00 to 6.25 mM). The detection limit and linear correlation coefficient were 49.3 ppm (1.10 mM) and 0.9998, respectively. The unsupported PdNP-modified glassy carbon electrodes presented good cyclic voltammetric stability for ethanol sensing application in alkaline media.     

Hydrogel-based flexible micro-reference electrodes for use in alkaline and neutral pH solutions

Two types of nonbreakable, flexible micro-reference electrodes filled with gel-electrolytes were prepared for use in solutions with alkaline and neutral pH. The electrodes are intended for electrochemical measurements, in which chloride-free conditions are important. Due to the flexible, bendable construction of the electrodes, electrochemical experiments at locations difficult to access with common reference electrodes are enabled. Hg|HgO-type electrodes were prepared from amalgamated Au wires, followed by oxidation of the amalgam, which is mounted in a PTFE tube filled with 0.1M NaOH solution immobilized in a PAA-g-PEO gel. The potential of this type of electrode was found to be 0.162?±?0.002 V (SHE) at room temperature. Cu|CuSO₄ electrodes, consisting of a Cu wire immersed in a saturated CuSO₄ solution jellied with gelatin, showed a stable open-circuit potential of 0.312?±?0.001 V (SHE). Further characterization of the electrodes was performed in terms of electrochemical impedance spectroscopy and micro-polarization measurements. As an alternative to the flexible electrodes, rigid electrodes in glass enclosure were fabricated in analogy to the flexible-type electrodes.     

Synthesis and Temperature-dependent Electrochemical Properties of Boron-doped Diamond Electrodes on Titanium

On the sand-blasting-treated titanium(Ti) substrate, the boron-doped diamond(BDD) electrodes with a wide potential window were prepared by microwave plasma chemical vapor deposition(MPCVD). The electrochemical oxidation ratios of phenol at BDD/Ti electrodes at elevated temperatures(from 20 ℃ to 80 ℃) were examined by the chemical oxygen demand(COD) of phenol electrolyte during electrolysis. The results show that the COD removal was increased at high temperatures and the optimized temperature for enhancing the electrochemical oxidation ratio of phenol is 60 ℃. The mechanism for the temperature-dependent electrochemical oxidation ratios of phenol at the electrodes was investigated. The study would be favorable for further improving the performance of BDD/Ti electrodes, especially working at high temperatures.     

Anisotropy in the anodic oxidation of silicon in KOH solution

The electrochemical oxidation and passivation of Si(100) and Si(111) electrodes in KOH solution was studied by potentiodynamic and potential-step measurements. Striking differences were observed between the surfaces. A comparison of the results for n- and p-type electrodes led us to conclude that electrochemical oxidation of silicon in alkaline solution must be triggered by a chemical reaction. The strong influence of temperature on the current-potential and current-time results of (111) surfaces supports the importance of chemical activation. Photocurrent experiments on n-type (111) electrodes show that oxide nucleation is important for growth of the passive layer. A mechanism combining surface chemistry and electrochemistry is proposed to account for the pronounced anisotropy in anodic oxidation.     

Electrochemical and sem characterization of Ag electrodes roughened by potential sweep and potential step processes in aqueous chloride and chloride + pyridine media

The effect of solution pH and the presence of pyridine on the redox behavior of Ag electrodes in aqueous chloride media is investigated. Scanning electron microscopy is used to evaluate differences in surface morphology of Ag electrodes subjected to electrochemical oxidation and oxidation—reduction processes in 0.1 M KCl and 0.1 M KCl + 0.05 M pyridine media at pH values of 2, 7, and 12. Potential sweep and potential step methods are used to effect the electrochemical oxidation and oxidation—reduction events. Comparisons are made between the resulting surface morphologies on the submicroscopic level for Ag surfaces roughened in these two ways. The redox chemistry of the oxidation and reduction processes is interpreted in terms of the different species capable of interacting with the Ag electrode surface and Ag⁺ species generated during oxidation in each medium. Surface adsorbates proposed to be important include chloride ions and pyridine. The relative importance of these species in terms of their ability to influence the redox chemistry of the Ag electrodes is seen to be a sensitive function of solution pH.     

Composite gas-diffusion anodes for hydrogen generation by the sulfate-acid procedure

New composite catalytically-active coatings of gas-diffusion graphite electrodes were offered for the electrochemical SO₂ oxidation in the sulfate-acid cycle of hydrogen generation. Kinetics of SO₂ oxidation on porous graphite electrodes activated by platinum and metal-oxide catalysts was studied.     

Copper-modified gold electrode specific for monosaccharide detection Use in amperometric determination of phenylmercury based on invertase enzyme inhibition

The electrochemical oxidation of mono- and disaccharides at various copper-modified electrodes is reported: glassy carbon modified at open circuit or by electrochemical deposition of copper, gold modified by electrochemical deposition, and at bulk copper electrodes. A comparative study of these four electrodes was made by linear sweep voltammetry and amperometry. The maximum oxidation peak separation between disaccharides and monosaccharides is about 200 mV. After optimization, amperometric determination of monosaccharides was done at +0.30 versus Ag/AgCl in 0.15 M NaOH at the copper-modified gold electrode.

Using the developed method, the enzymatic activities of invertase and β-galactosidase were determined through their reaction with sucrose and lactose, respectively. Validation was carried out by a spectrophotometric method based on 3,5-dinitrosalicylic acid, and it was shown that the proposed electrochemical method is more sensitive.

The analytical utility of the copper-modified gold electrode was tested for the determination of organic mercury. Addition of phenylmercury standards to the invertase solution caused a decrease in the enzyme activity, and allowed the determination of phenylmercury in pharmaceutical samples. The concentration has been determined in the 10–55 ng ml⁻¹ range.     

Demonstration of the advantages of using bamboo-like nanotubes for electrochemical biosensor applications compared with single walled carbon nanotubes

The modification of glassy carbon electrodes with random dispersions of nanotubes is currently the most popular approach to the preparation of carbon nanotube modified electrodes. The performance of glassy carbon electrodes modified with a random dispersion of bamboo type carbon nanotubes was compared with single walled carbon nanotubes modified glassy carbon electrodes and bare glassy carbon electrodes. The electrochemical performance of all three types for electrode were compared by investigating the electrochemistry with solution species and the oxidation of guanine and adenine bases of surface adsorbed DNA. The presence of edge planes of graphene at regular intervals along the walls of the bamboo nanotubes resulted in superior electrochemical performance relative to SWNT modified electrodes from two aspects. Firstly, with solution species the peak separation of the oxidation and reduction waves were smaller indicating more rapid rates of electron transfer. Secondly, a greater number of electroactive sites along the walls of the bamboo-carbon nanotubes (BCNTs) resulted in larger current signals and a broader dynamic range for the oxidation of DNA bases.     

Ni-P-TiO2化学复合镀层电极的乙醇电催化氧化

于Ni-P镀液添加TiO2颗粒,用化学镀法在黄铜基底上制备不同TiO2含量的Ni-P-TiO2复合镀层电极.采用循环伏安法、线性扫描法、计时电流和交流阻抗法测定Ni-P-TiO2/Cu电极的电化学性能.结果表明:常温下Ni-P-TiO2/Cu电极在碱性溶液中对乙醇氧化有很高的电催化活性;Ni-P-TiO2电极上乙醇的电催化氧化活性随镀层TiO2量的不同而异;镀液中TiO2含量为5 g.L-1时,所得电极的电催化乙醇氧化的活性最佳.     

Voltammetric measurement of reduced nicotinamide-adenine nucleotides and application to amperometric measurement of enzyme reactions.

The electrochemical oxidations of reduced nicotinamide-adenine dinucleotide and reduced nicotinamide-adenine dinucleotide phosphate on platinum and carbon electrodes are described. Well defined voltammetric anodic waves are observed on carbon electrodes, with a linear relationship between peak height and concentration for 0–0.5mM NADH and NADPH. Amperometric methods for NAD oxidoreductase analyses by direct electrochemical oxidation of the reduced nucleotide have been developed for lactic dehydrogenase and ethanol in serum.     

Review on the electrochemical oxidation of endocrine-disrupting chemicals using BDD anodes

The application of synthetic diamond-based electrodes in water treatment has been shown to be promising, especially for boron-doped diamond (BDD). With a wide potential window and high overpotential for oxygen evolution among many more excellent qualities, BDD anodes surpass the capabilities of conventional electrodes. Currently, the synthesis and fabrication of low-cost BDD anodes are still in the primary stages of development. Electrochemical oxidation of EDCs on BDD anodes in water samples have been shown to be effective with very high removal efficiencies. The presence of this group of pollutants in wastewater effluents and various water matrices causes environmental concerns and requires an immediate solution due to their persistence and threat for both humas and wildlife. Extensive research on BDD continues to be carried out with various EDCs, such as parabens and pesticides, to determine the most suitable parameters, possible mechanisms of the degradation process, and its viability in large-scale applications. These efforts remain imperative as the presence of EDCs could severely affect human health and the surrounding environment. Although significant progress has been achieved, the advanced technology is unable to achieve feasible application in a large scale due to major hindrances. In this mini review, the focus was on the recent applications of electrochemical oxidation using BDD thin-film anodes (2019 to present) for the removal of a range of EDCs. The main factors that affect the performance of BDD anodes in the electrochemical oxidation of EDCs were discussed and evaluated, highlighting some ways to overcome the issues that prevent the technology from moving onto the next stage of development.     

Influence of Surface Structure of Platinum Electrodes on Electrooxidation of CO

The oxidation of CO on platinum electrodes in an acid solution was studied with the conventional electro-chemical methods and the on-line electrochemical mass spectroscopy. It was found that this reaction is strongly determined by the surface morphology of platinum. The pretreatment of platinum electrodes can change the surface properties dramatically, in consequence it can improve the electrocatalytic activity towards the electrooxidation of CO. The existence of surface active sites on the roughened platinum electrodes can be used to explain its high electrocatalysis towards the oxidation of CO.     

Nafion® Coated Electropolymerised Flavanone-based pH Sensor

This work summarizes the electrochemical response of flavanone carbon composite electrodes in comparison with Nafion®-coated flavanone carbon composite electrodes, for use as voltammetric pH sensors in both buffered and low-buffered media. Square wave voltammetric measurements suggest the peak potential achieved from the electrochemical polymerization after the electron-proton oxidation responds with accuracy to buffered pH solutions for both coated and non-coated electrodes, with a potential shift of 55.1 mV and 54.6 mV per pH unit respectively. However, a considerable improvement in stability, accuracy and sensitivity is provided by the proton-transfer Nafion® layer in CO₂ bubbled sea water. Furthermore, Nafion®-coated flavanone carbon composite electrodes predicted a pH of 8.04 for the commercial seawater, which is in excellent agreement with the measured pH 8.05 value.     

Graphene oxides/multi-walled carbon nanotubes hybrid-modified carbon electrodes for fast and sensitive voltammetric determination of the anticancer drug 5-fluorouracil in spiked human plasma samples

The electrochemical oxidation of anticancer drug 5-fluorouracil (5-FU) at graphene oxides (GOs)/carbon nanotubes (CNTs) nanohybrid-modified screen-printed carbon and glassy carbon electrodes was studied by voltammetric techniques. The modified electrodes showed better performance toward the electro-oxidation and determination of 5-FU compared to CNTs-modified or GOs-modified electrodes. The oxidation peak current obtained at about + 1.156 V (vs. Ag/AgCl) from square wave voltammetry was linearly dependent on the 5-FU concentration in the ranges of 0.05–5 and 5–1200 µM in phosphate buffer solution of pH 7.0. The developed method was applied successfully to the electrochemical sensing of 5-FU in human plasma samples at micro-molar concentration levels with satisfactory results. It is hopeful that the developed method in the future can be used for the simple and fast determination of 5-FU in clinical test and pharmacokinetics.     

Comparison of the Electrochemical Reactivity of Carbon Nanotubes Paste Electrodes with Different Types of Multiwalled Carbon Nanotubes

Carbon nanotubes (CNTs) are widely used in electrochemical studies. It is reported that CNTs with different source and dispersed in different agents [1] yield significant difference of electrochemical reactivity. Here we report on the electrochemical performance of CNTs paste electrodes (CNTPEs) prepared by multiwalled carbon nanotubes (MWNTs) with different diameters, lengths and functional groups. The resulting electrodes exhibit remarkable different electrochemical reactivity towards redox molecules such as NADH and K₃[Fe(CN)₆]. It is found that CNTPEs prepared by MWNTs with 20–30 nm diameter show highest catalysis to NADH oxidation, while CNTPEs prepared by MWNTs with carboxylate groups have best electron‐transfer rate (The peak‐peak separation (ΔE_p) is +0.108 V for MWNTs with carboxylate groups, +0.155 V for normal MWNTs, and +0.174 V for short MWNTs) but weak catalysis towards oxidation of NADH owing to the hydrophilicity of carboxylate groups. The electrochemical reactivity depends on the lengths of CNTs to some extent. The ‘long’ CNTs perform better in our study (The oxidation signals of NADH appear below +0.39 V for ‘long’ CNTs and above +0.46 V for the ‘short’ one totally). Readers may get some directions from this article while choose CNTs for electrochemical study.     

Electrochemical Oxidation Properties of Benzyl Alcohol on Pt/SPE Electrodes

The electrochemical oxidation properties of benzyl alcohol on Pt/SPE electrodes were investigated using electrochemical methods in this work. As shown in Fig.l,benzyl alcohol could be oxidized on Pt/SPE electrodes, the oxidation peak potential was 1.18 V (vs. SCE) in acetone solution.     

Investigation of Metal Ion Effect on Specific DNA Sequences and DNA Hybridization

In this article, we investigated the sequence specific interaction of single (ssDNA) and double stranded (dsDNA) with silver ions (Ag⁺) with electrochemical methods. We, for the first time, examined the effect of base sequences, base content and physiochemical properties of different DNA sequences on interaction with Ag⁺ in detail. We used different base contents to show how the composition of nucleic acid influences the electrochemical signals. We first immobilized ssDNA probes on bare graphite electrodes. Then, we showed the sequence effect on oxidation signals of AgDNA complex by sensing Ag⁺ to the probe coated surfaces to interact with different ssDNA sequences. Furthermore, we investigated the effect of Ag⁺ on dsDNA. We measured the oxidation signals obtained from Ag⁺‐ssDNA and Ag⁺‐dsDNA complex at approximately 0.2 V and 1.0 V (vs Ag/AgCl), respectively with Differential Pulse Voltammetry (DPV). We showed that the oxidation signals of the AgDNA complex obtained from dsDNA‐modified electrodes is higher than the electrodes modified with ssDNA. More importantly, we showed that Ag⁺‐ssDNA and Ag⁺ ion‐dsDNA exhibit different electrochemical behaviors.     

Tin oxide nanoparticles-polymer modified single-use sensors for electrochemical monitoring of label-free DNA hybridization

In this study, SnO₂ nanoparticles (SNPs)-poly(vinylferrocenium) (PVF⁺) modified single-use graphite electrodes were developed for electrochemical monitoring of DNA hybridization. The surfaces of polymer modified and polymer-SNP modified pencil graphite electrodes (PGEs) were firstly characterized by using SEM analysis. The electrochemical behaviours of these electrodes were also investigated using the differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS) techniques. The polymer-SNP modified PGEs were then tested for the electrochemical sensing of DNA based on the changes at the guanine oxidation signals. Experimental parameters, such as; different modifications in DNA oligonucleotides, DNA probe concentrations were examined to obtain more sensitive and selective electrochemical signals for nucleic acid hybridization. After optimization studies, DNA hybridization was investigated in the case of complementary of hepatitis B virus (HBV) probe, mismatch (MM), and noncomplementary (NC) sequences.