Accumulation of cadmium,lead, and nickel by fungal and wood biosorbents

Native fungal biomass of fungiAbsidia orchidis, Penicillium chrysogenum, Rhizopus arrhizus, Rhizopus nigricans, and modified spruce sawdust (Picea engelmanii) sequestered metals in the following decreasing preference pb>Cd>Ni. The highest metal uptake was q_max = 351 mg Pb/gA. orchidis biomass. P.chrysogenum biomass could accumulate cadmium best at 56 mg Cd/g. The sorption of nickel was the weakest always at < 5 mg Ni/g. The spruce sawdust was modified by crosslinking, oxidation to acidic oxoforms, and by substitution. The highest metal uptake was observed in phosphorylated sawdust reaching q_max = 224 mg Pb/g, 56 mg Cd/g, and 26 mg Ni/g. The latter value is comparable to the value of nickel sorption by wet commercial resin Duolite GT-73. Some improvement in metal uptake was also observed after reinforcement of fungal biomass.     

Removal and recovery of copper (II) ions by bacterial biosorption

Studies were conducted toinvestigate the removal and recovery of copper (II) ions from aqueous solutions by Micrococcus sp., which was isolated from a local activated sludge process. The equilibrium of copper biosorption followed the Langmuir isotherm model very well with a maximum biosorption capacity (q_max) of 36.5 mg of Cu²⁺/gofdry cell at pH 5.0 and 52.1 mg of Cu²⁺/g of dry cell at pH 6.0. Cells harvested at exponential growth phase and stationary phase showed similar biosorption characteristics for copper, Copper uptake by cells was negligible at pH 2.0 and then increased rapidly with increasing pH un til 6.0. In multim etal systems, Micrococcus sp. exhibited a preferential biosorption order: Cu−Pb>Ni−Zn. There is virtually no interference with copper uptake by Micrococcus sp. from solutions bearing high concentrations of Cl⁻, SO ₄ ²⁻ , and NO3/− (0–500 mg/L). Sulfuric acid (0.05 M) was the most efficient desorption medium, recovering >90% of the initial copper sorbed. The copper capacity of Micrococcus sp. remained unchanged after five successive sorption and desorption cycles. Immobilization of Micrococcus sp. in 2% calcium alginate and 10% polyacrylamide gel beads increased copper uptake by 61%. Biomass of Micrococcus sp. may be applicable to the development of potentially cost-effective biosorbent for removing and recovering copper from effluents.     

Biosorption of heavy metals by bacteria isolated from activated sludge

Twelve aerobic bacteria from activated sludge were isolated and identified. These included both Gram-positive (e.g., Bacillus) and Gram-negative (e.g., Pseudomonas) bacteria. The biosorption capacity of these strains for three different heavy metals (copper, nickel, and lead) was determined at pH 5.0 and initial metal concentration of 100 mg/L. Among these 12 isolates, Pseudomonas pseudoalcaligenes was selected for further investigation owing to its high metal biosorption capacity. The lead and copper biosorption of this strain followed the Langmuir isotherm model quite well with maximum biosorption capacity (q _max) reaching 271.7mg of Pb²⁺/g of dry cell and 46.8 mg of Cu²⁺/g of dry cell at pH 5.0. Study of the effect of pH on lead and copper removal indicated that the metal biosorption increased with increasing pH from 2.0 to 7.0. A mutual inhibitory effect was observed in the lead-copper system because the presence of either ion affected the sorption capacity of the other. Unequal inhibitions were observed in all the nickel binary systems. The increasing order of affinity of the three metals toward P. pseudoalcaligenes was Ni<Cu<Pb. The metal biosorptive potential of these isolates, especially P. pseudoalcaligenes, may have possible applications in the removal and recovery of metals from industrial effluents.     

Study of physical chemistry on biosorption of zinc by using Chlorella pyrenoidosa

Discharge of heavy metals from metal processing industries is known to have adverse effects on the environment. Biosorption of heavy metals by metabolically inactive biomass of microbial organisms is an innovative and alternative technology for removal of these pollutants from aqueous solution. Presence of heavy metals in the aquatic system is posing serious problems. Zinc has been used in many industries and removal of Zn ions from waste water is significant. Biosorption is one of the economic methods used for removal of heavy metals. In the present study, the biomass obtained from the dried Chlorella pyrenoidosa was used for evaluating the biosorption characteristics of Zn ions in aqueous solutions. Batch adsorption experiments were performed with this material and it was found that the amount of metal ions adsorbed increased with the increase in the initial metal ion concentration. In this study effect of agitation time, initial metal ion concentration, temperature, pH and biomass dosage were studied. Maximum metal uptake (q _max) observed at pH 5 was 101.11 mg/g. The biosorption followed both Langmuir and Freundlich isotherm model. The adsorption equilibrium was reached in about 1 h. The kinetic of biosorption followed the second-border rate. The biomass could be regenerated using 0.1 M HNO₃. A positive value of ΔH° indicated the endothermic nature of the process. A negative value of the free energy (ΔG°) indicated the spontaneous nature of the adsorption process. A positive value of ΔS° showed increased randomness at solid-liquid interface during the adsorption of heavy metals, it also suggests some structural changes in the adsorbate and the adsorbent. FTIR Spectrums of Chlorella pyrenoidosa revealed the presence of hydroxyl, amino, carboxylic and carbonyl groups. The scanning electron micrograph clearly revealed the surface texture and morphology of the biosorbent.     

Characteristics of sorption of uncomplexed and complexed Pb(II) from aqueous solutions onto peat

Batch experiments aimed at the sorption of Pb(II) onto peat were performed from an aqueous solution in both the absence and presence of common complexing agents (acetate or citrate). The influence of the initial pH of the solution, metal ion concentration and contact time on the sorption efficiency of Pb(II) was examined at ambient temperature (18 ± 0.5) °C for each experiment. The results showed that the presence of acetate improved the efficiency of the sorption process, while the presence of citrate in the aqueous solution decreased the efficiency of the Pb(II) sorption onto peat. The equilibrium data fitted well with the Langmuir isotherm model and confirmed the monolayer sorption of uncomplexed and complexed Pb(II) species onto peat. The values of maximum sorption capacities (q _max) were 135.13 mg g⁻¹ for Pb(II) complexed with acetate, q > 79.36 mg g⁻¹ for uncomplexed Pb, q > 38.46 mg g⁻¹ for Pb(II) complexed with citrate. The kinetics of Pb(II) sorption onto peat, in both the absence and presence of complexing agents, indicated a pseudosecond order mechanism. Analysis of IR spectra showed that carboxylic and hydroxyl groups had an important role in the binding process of Pb(II) species onto peat.     

A study of the removal of heavy metals from aqueous solutions by Moringa oleifera seeds and amine-based ligand 1,4-bis[N,N-bis(2-picoyl)amino]butane

Uptake for lead, copper, cadmium, nickel and manganese from aqueous solution using the Moringa oleifera seeds biomass (MOSB) and amine-based ligand (ABL) was investigated. Experiments on two synthetic multi-solute systems revealed that MOSB performed well in the biosorption and followed the decreasing orders Pb(II) > Cu(II) > Cd(II) > Ni(II) > Mn(II) and Zn(II) > Cu(II) > Ni(II). The general trend of the heavy metal ions uptake by the amine-based ligand followed decreased in the order Mn > Cd > Cu > Ni > Pb, which is the reverse trend for what was observed for MOSB. Comparing the single- and multi-metal solutions, there was no clear effect in the biosorption capacity of MOSB suggesting the presence of sufficient active binding sites for all metal ions studied. The MOSB performance is also not affected by pH in the range 3.5–8.     

Equilibrium,kinetic and thermodynamic biosorption studies of Hg(II) on red algal biomass of Porphyridium cruentum

Among a variety of microbial materials employed for biosorption, algae have added advantages of non-toxic and autotrophic nature. In this study, biosorption of Hg(II) was studied with red algal biomass of Porphyridium cruentum. The parameters affecting biosorption such as dosage of biosorbent, pH, contact time, initial metal concentration, temperature and effect of foreign metal cations in binary system were evaluated. Kinetic data were described with the help of pseudo-first-order and pseudo-second-order kinetic models. Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models were applied to adsorption equilibrium data. According to the results, the maximum removal capacity (q_max) was 2.62?mg/g observed at pH 7 with 0.25?g/L of biosorbent dosage for Hg(II) solution containing 10?mg/L of metal ions. The Langmuir isotherm model fits best to the adsorption data while the kinetic data followed the pseudo-second-order model. Thermodynamics studies showed that the biosorption process of Hg(II) on P. cruentum was exothermic in nature.     

Evaluation of Dry Protonated Calcium Alginate Beads for Biosorption Applications and Studies of Lead Uptake

Alginate polysaccharide is a promising biosorbent for metal uptake. Dry protonated calcium alginate beads for biosorption applications were prepared, briefly characterized and tested for lead uptake. Several advantages of this biosorbent are reported and discussed in comparison with other alginate-based sorbents. The alginate beads contained 4.7 mmol/g of COOH groups, which suffered hydrolysis near pH 4. The Weber and Morris model, applied to kinetic results of lead uptake, showed that intraparticle diffusion was the rate-controlling step in lead sorption by dry alginate beads. Equilibrium experiments were performed and the data were fitted with different isotherm models. The Langmuir equation was the most adequate to model lead sorption. The maximum uptake capacity (q _max) was estimated as 339 mg/g and the Langmuir constant (b) as 0.84 l/mg. These values were compared with that of other sorbents found in the literature, indicating that dry protonated calcium alginate beads are among the best biosorbents for the treatment and recovery of heavy metals from aqueous streams.     

Determination of trace metals in Nile River and ground water by differential pulse stripping voltammetry

The determination of trace metals in river water and ground water by DPSV is seriously disturbed by the presence of organic complexes. The influence of these substances can be eliminated by acidification of the samples with acids. Cd, Pb and Cu were determined at pH 1.1 (HNO₃ medium) and Zn, Cd, Pb and Cu at pH 2 (HCl medium), in both the Nile river and ground water. Zn was determined at pH 3.5 in HCl and pH 4.5 in HNO₃, after neutralizing the samples with NH₃/NH₄Cl buffer. Manganese could then be determined, after further addition of ammoniacal buffer solution up to pH 7.5 and 8.5. Ni and Co were determined in the adsorptive mode after formation of dimethylglyoximates at pH 9.2. The effect of pH on the stripping peaks of manganese was studied. Good agreement was observed between DPSV and AAS results for Zn, Cd, Pb, Cu and Mn, but the concentrations of Ni and Co were below the detection limits for AAS. Good agreement was obtained between DPSV results in HCl and HNO₃ for Ni and Co. The results indicate that decomposition of organic complexes by acidification with HNO₃ is better than in the case with HCl for Zn, Pb, Cu, Ni and Co, but HCl is better than HNO₃ for Cd and Mn.     

Cleansing contaminated seawaters using marine cyanobacteria: evaluation of trace metal removal from the medium

The use of microbial biomass in biosorption is already being studied as a potential alternative to (or combined with) conventional processes, where several algae and microorganisms have already shown promising ability to uptake metals. Cyanobacteria (blue-green algae) are widespread organisms, with specific properties, such as high nutrient removal capacity and tolerance to highly variable conditions which make them well-suited for wastewater and remediation purposes. The main aim of this work was to evaluate the use of a marine cyanobacterium LEANCYA 21 (Synechocystis sp.), collected from the Portuguese southern border, for the removal of selected trace metals when in natural seawater culture medium. It was observed, for the first time, that this particular strain is capable of uptaking Pb, Ni and Zn (at nM levels) from seawater solutions using small amounts of biomass. Uptake values for Pb were up to 90% (0.75 mg g^?1 biomass) in 6 h. The specific biosorption curves of Ni and Zn showed that these metals follow a first order kinetics biosorption in batch conditions. Solutions containing multimetals have revealed that Ni uptake is affected by the presence of Pb and Zn. The calculated specific absorption values were high enough to predict a possible application in aquaculture where such low levels of metals may inhibit microalgae growth.     

Solid phase extraction of metal ions using carbon nanotubes

The sorption behaviour of carbon nanotubes (CNTs) toward some divalent metal ions such as Cu(II), Co(II), Ni(II), Zn(II), Pb(II), Mn(II) and Cd(II) has been investigated systematically. The affinity order of the metal ions towards CNTs at pH in the range of 7.0-9.0 was: Cu(II) > Pb(II) > Zn(II) > Co(II) > Ni(II) > Cd(II) > Mn(II). The experimental parameters for preconcentration of copper, which exhibits the highest affinity towards carbon nanotubes, on a microcolumn packed with CNTs prior to its determination by flame atomic absorption spectrometry have been investigated. Copper can be quantitatively retained at pH 8.2 from sample volume up to 150 mL and then eluted completely with 0.1 mol L^− 1 HNO₃. The limit of detection limit for Cu(II) determination with FAAS detection was 2.1 μg L^− 1, and the RSD was 3.5% at the 50 μg L^− 1 level. Under the optimal conditions for copper enrichment also Zn(II), Pb(II) and Ni(II) could be quantitatively preconcentrated from water samples. The method was validated using a certified reference materials BCR-610 and SRM 1640.     

Watermelon Rind: Agro-waste or Superior Biosorbent?

Biosorption of copper (Cu), zinc (Zn), and lead (Pb) on watermelon rind in a well-stirred batch system was investigated. pH showed significant influence on the biosorption process. Optimal pH for Cu, Zn, and Pb biosorption was found to be 5.0, 6.8 and 6.8, respectively. Watermelon rind was in favor of Pb and it could remove up to 99% Pb between pH ranges of 5 and 6.8 when Pb concentration is lower than 100 mg/L. The biosorptive capacity of watermelon on Cu, Zn, and Pb was 6.281, 6.845, and 98.063 mg/g, respectively. The equilibrium data fitted well to Langmuir adsorption isotherm while pseudo-second-order kinetic model exhibited more advantages for describing kinetic data than pseudo-first-order kinetic model. NaOH was found to be a suitable eluent. After desorption in NaOH solution, the resorption efficiency reached as high as 99% of these three metals either in a single-component or multi-component system. From the characterization study, ion exchange and micro-precipitation were estimated to be the main mechanisms. Due to its high metal uptake capacity, reusability, and metal recovery, watermelon rind can be considered as an eco-friendly and economic biosorbent for removing Pb from water and wastewater.     

Preparation of morin modified nanometer SiO<Subscript>2</Subscript> as a sorbent for solid-phase extraction of trace heavy metals from biological and natural water samples

Morin was successful as a chemical modifier to improve the reactivity of the nanometer SiO₂ surface in terms of selective binding and extraction of heavy metal ions. This new functionalized nanometer SiO₂ (nanometer SiO₂-morin) was used as an effective sorbent for the solid-phase extraction (SPE) of Cd(II), Cu(II), Ni(II), Pb(II), Zn(II) in solutions prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Experimental conditions for effective adsorption of trace levels of metal ions were optimized with respect to different experimental parameters using static and dynamic procedures in detail. The pH 4.0 was chosen as the optimum pH value for the separation of metal ions on the newly sorbent. Complete elution of the adsorbed metal ions from the nanometer SiO₂-morin was carried out using 2.0 mL of 0.5 mol L⁻¹ of HCl. Common coexisting ions did not interfere with the separation and determination at pH 4.0. The maximum static adsorption capacity of the sorbent at optimum conditions was found to be 22.36, 36.8, 40.37, 33.21 and 25.99 mg metal/g SiO₂-morin for Cd(II), Cu(II), Ni(II), Pb(II) and Zn(II), respectively. The time for 95% sorption for Cu(II) and Ni(II) and 70% sorption for Cd(II), Pb(II) and Zn(II) was less than 2 min. The relative standard deviation (RSD) of the method under optimum conditions was lower than 5.0% (n = 11). The procedure was validated by analyzing the certified reference river sediment material (GBW 08301, China), the results obtained were in good agreement with standard values. The nanometer SiO₂-morin was successfully employed in the separation and preconcentration of trace Cd(II), Cu(II), Ni(II), Pb(II) and Zn(II) from the biological and natural water samples yielding 75-folds concentration factor.     

Thermodynamic and isotherm studies of the biosorption of Cu(II), Pb(II), and Zn(II) by leaves of saltbush (Atriplex canescens)

The Freundlich and Langmuir isotherms were used to describe the biosorption of Cu(II), Pb(II), and Zn(II) onto the saltbush leaves biomass at 297 K and pH 5.0. The correlation coefficients (R²) obtained from the Freundlich model were 0.9798, 0.9575, and 0.9963 for Cu, Pb, and Zn, respectively, while for the Langmuir model the R² values for the same metals were 0.0001, 0.1380, and 0.0088, respectively. This suggests that saltbush leaves biomass sorbed the three metals following the Freundlich model (R² > 0.9575). The K_F values obtained from the Freundlich model (175.5 · 10⁻², 10.5 · 10⁻², and 6.32 · 10⁻² mol · g⁻¹ for Pb, Zn, and Cu, respectively), suggest that the metal binding affinity was in the order Pb > Zn > Cu. The experimental values of the maximal adsorption capacities of saltbush leaves biomass were 0.13 · 10⁻², 0.05 · 10⁻², and 0.107 · 10⁻² mol · g⁻¹ for Pb, Zn, and Cu, respectively. The negative ΔG^∘ values for Pb and the positive values for Cu and Zn indicate that the Pb biosorption by saltbush biomass was a spontaneous process.     

N-vinylcarbazole polymerization by 13X molecular sieve exchanged with Mn(II), Co(II), Ni(II), Cu(II) and Zn(II)

The polymerization of N-vinylcarbazole by 13X molecular sieves modified by five different transition metal ions, viz. Mn(II), Co(II), Ni(II), Cu(II) and Zn(II), has been studied under various conditions. The order of reactivity follows the trend: Mn(II) ≈ Cu(II) > Co(II) > Zn(II) > Ni(II) at pH ∼ 3.55 and an exchange level of 30% of the metal ion. The polymerizations are believed to occur by a dual-ion-initiation mechanism in which both metal ions and proton centres participate. The overall energy of activation (E_a) for each system decreases with decreasing pH of the exchanging salt solution. Average activation energy on proton centre (E_H) and that on metal ion centre (E_a) have been evaluated for each system. E_a, E_H and E_c have been shown to correlate with one another. The molecular weights and their distributions are affected by the nature of the metal ion and also by the protonic centres. The possibility of a correlation of the catalytic activity of the modified 13X with ionic radius, electronegativity and normal co-ordination number has been examined.     

Phosphoric acid activated carbon as borderline and soft metal ions scavenger

Three activated carbons have been prepared, two from oil-palm shell and one from coconut shell, by the phosphoric acid activation process. Adsorption isotherms of copper(II) were determined to evaluate and compare the performance of experimental carbons. The obtained data are fitted very well to Langmuir and Freundlich adsorption models. All prepared activated carbons show 4–7-fold high adsorption capacity (q_max 19.5–23/18.6–21?mg?g^?1) than that of the commercial ones (q_max 5.6/2.9?mg?g^?1) under the conducted experimental conditions. The mechanism of adsorption was evaluated from the competitive adsorption of copper(II) and calcium(II) in a binary solution depending on their behaviour as Lewis acid and assessed as inner-sphere complexation. The competitive adsorption of copper(II) with other borderline and soft metal ions was evaluated by the best scavenger using a solution of ternary solute of copper(II), nickel(II) and lead(II). The adsorption selectivity order is determined as follows: Pb?>?Cu???Ni.     

Good linear relationship between logarithms of Eigen’s water exchange constants for several divalent metal ions and activation energies of corresponding metal-catalyzed alkoxysilane hydrolysis in ethylene-propylene copolymer system

Catalytic efficiencies of seven divalent metal acetylacetonate complexes [M(acac)₂; M = Cd(II), Co(II), Cu(II), Fe(II), Ni(II), Pb(II), and Zn(II)] with respect to the water-crosslinking kinetics of vinyltrimethoxysilane-grafted ethylene-propylene copolymer (EPR-g-VTMS) were investigated to examine the effects of progressive changes in metal ion using ATR-FTIR spectroscopy. The hydrolysis activation energies of EPR-g-VTMS follows the order: No catalyst ≈ Ni(acac)₂ > Co(acac)₂ > Fe(acac)₂ ≈ Zn(acac)₂ > Cd(acac)₂ ≈ Cu(acac)₂ > Pb(acac)₂. Interestingly, the kinetics results revealed that the plots of hydrolysis activation energies of EPR-g-VTMS containing M(acac)₂ complexes and Eigen’s water exchange constants for corresponding metal ions showed a excellent linear relationship, suggesting that the reaction pathway for the silane water-crosslinking with hydrous M(acac)₂ complex in EPR-g-VTMS system may be similar to that for water exchange of the metal ion in an aqueous system. Based on the knowledge of traditional kinetics studies by Eigen and Wilkins and hybrid sol-gel chemistry, the plausible catalytic mechanism for M(acac)₂ complexes in EPR-g-VTMS system was proposed.     

Poly(vinylbenzyl Pyridinium Salts) as Novel Sorbents for Hazardous Metals Ions Removal

Novel efficient complexing resins—poly(vinylbenzyl pyridinium salts) fabricated through poly(vinylbenzyl halogene-co-divinylbenzene) quaternization of N-decyloxy-1-(pyridin-3-yl)ethaneimine and N-decyloxy-1-(pyridin-4-yl)ethaneimine—were tested as adsorbents of Pb(II), Cd(II), Cu(II), Zn(II), and Ni(II) from aqueous solutions. The structure of these materials was established by ¹³C CP-MAS NMR, X-ray photoelectron spectroscopy, elemental analysis, and Fourier transform infrared spectroscopy, as well as thermogravimetric and differential thermal analyses. The textural properties were determined using scanning electron microscopy and low-temperature N₂ sorption. Based on the conducted sorption studies, it was shown that the uptake behavior of the metal ions towards novel resins depended on the type of functionalities, contact time, pH, metal concentrations, and the resin dosage. The Langmuir model was investigated to be the best one for fitting isothermal adsorption equilibrium data, and the corresponding adsorption capacities were predicted to be 296.4, 201.8, 83.8, 38.1, and 39.3 mg/g for Pb(II), Zn(II), Cd(II), Cu(II), and Ni(II), respectively. These results confirmed that owing to the presence of the functional pyridinium groups, the resins demonstrated proficient metal ion removal capacities. Furthermore, VBBr-D4EI could be successfully used for the selective uptake of Pb(II) from wastewater. It was also shown that the novel resins can be regenerated without significant loss of their sorption capacity.     

Road dust pollution of Cd, Cu, Ni, Pb and Zn along Islamabad Expressway, Pakistan

Islamabad Expressway is one of the busiest roads in the capital of Pakistan. For the assessment of heavy metal pollution level in dust generated on the Expressway, 13 samples of dust were collected from various places around the highway and four samples of soil were obtained from the undisturbed green land in Islamabad. The samples were analyzed for five heavy metals using FAAS (flame atomic absorption spectrometry). The average concentration values of the metals Cd, Cu, Ni, Pb and Zn were found to be 5 ± 1, 52 ± 18, 23 ± 6, 104 ± 29 and 116 ± 35 mg kg^{- 1} respectively, which were generally lower than the values cited in literature. The inter-elemental correlation of Cu and Pb indicated that they belonged to common anthropogenic sources. The pollution level was estimated based on the geoaccumulation index (I_geo), the pollution index (PI), and the integrated pollution index (IPI). The values of IPI were in the following order: Cu > Pb > Zn > Cd > Ni. All the indices for the metals under consideration were either low or corresponded to middle level of pollution. The pollution level is expected to increase due to rapid urbanization of the area. Some protective measures have therefore been proposed.