固相萃取-超快速液相色谱-串联质谱法测定当归中135种农药及其代谢物残留

建立了超快速液相色谱-串联质谱(UFLC-MS/MS)同时测定当归药材中135种农药及其代谢物(包括有机磷类、氨基甲酸酯类、拟除虫菊酯类农药等)残留量的分析方法。以回收率为考察指标,评估了不同的提取溶剂、固相萃取小柱、洗脱溶剂及体积对当归中多农残的提取净化效果,最终确定样品经乙腈提取,PSA固相萃取柱净化处理,在电喷雾正离子扫描、依赖保留时间的多反应监测模式(scheduled MRM)下,以基质匹配校准曲线内标法定量。结果表明,135种农药及其代谢物在各自的浓度范围内线性关系良好(r>0.99); 3个添加水平(10、50、100 μg/kg)下,除了烯草酮回收率偏低(62.0%~68.2%)外,其余农药的回收率为71.3%~119.7%,相对标准偏差(RSD, n=6)不大于19.9%, 135种农药及其代谢物的定量限为1.0~10.0 μg/kg。该方法样品前处理简单、快速、灵敏,可用于当归药材中多类别农药残留量的定性、定量。     

固相萃取-气相色谱法测定茶叶中残留的92种农药

建立了茶叶中92种农药多残留的气相色谱分析方法。茶叶样品用乙腈一次性提取后,有机磷类农药经Envi-Carb固相小柱净化,用10 mL乙腈-甲苯(体积比为3∶1)洗脱剂淋洗,气相色谱-火焰光度检测器(GC-FPD)检测;有机氯类和拟除虫菊酯类农药经串联Envi-Carb和NH2固相小柱净化,用5 mL乙腈-甲苯(体积比为3∶1)洗脱剂淋洗,GC-电子捕获检测器(ECD)检测。采用外标法定量。添加回收试验的结果表明:92种农药的平均回收率为80.3%～117.1%,相对标准偏差为1.5%～9.8%。方法的检出限为0.0025～0.10 mg/kg。该方法的灵敏度、准确度和精密度均符合农药残留测定的技术要求。     

Ultra-trace analysis of pesticides by solid-phase extraction of surface water with carbopack B cartridges, combined with large-volume injection in gas chromatography

Summary A method has been developed for determination of twenty-four polar pesticides—nine organophosphorus pesticides, thirteen organonitrogen compounds, and two triazine degradation products—in surface water. It entails extraction of the target pesticides from 1-L water samples by solid-phase extraction (SPE), then gas chromatography (GC) with large-volume (40 μL) injection. Filtered surface water, from the St Lawrence River in Canada and the River Loire and its tributaries in France, was extracted on cartridges filled with 500 mg Carbopack B (120–400 mesh). Analysis was performed by gas chromatography with a thermionic specific detector (GC-TSD) and a mass spectrometric (MS) detector. Overall percentage recoveries were satisfactory (>70%) for all target pesticides, with precision below 10%. Detection limits were between 0.5 and 4 ng L⁻¹.     

Combination of dispersive solid‐phase extraction and salting‐out homogeneous liquid–liquid extraction for the determination of organophosphorus pesticides in cereal grains

A new analytical method for the determination of organophosphorus pesticides in cereal samples was developed by combining dispersive SPE (d‐SPE) and salting‐out homogeneous liquid–liquid extraction (SHLLE). The pesticides were first extracted from cereal grains with acetonitrile, followed by d‐SPE cleanup. A 2 mL aliquot of the extract was then added to a centrifuge tube containing 9.2 mL water and 3.3 g NaCl for SHLLE. Analysis of the extract was carried out by gas chromatography coupled with flame photometric detection. The d‐SPE procedure effectively provides the necessary cleanup of the extract while SHLLE is used as an efficient concentration technique. Experimental parameters influencing the extraction efficiency including amounts of added water and salt were investigated. Recovery studies were carried out at three fortification levels, yielding recoveries in the range of 57.7–98.1% with the RSD from 3.7 to 10.9%. The reported limits of determination obtained from this study were 1 μg/kg, which is better than the conventional methods. In the analysis of 40 wheat and corn samples taken from Beijing suburbs, only two wheat samples have chlorpyrifos residue over the limits of determination.     

Multi-Residue Analysis of Some Polar Pesticides in Water Samples with SPE and LC–MS–MS

In the present study a multi-residue analytical method was developed for monitoring some polar pesticides such as acephate, methamidophos, carbofuran, isoproturon, dimethoate in water with SPE (solid-phase extraction) and LC–MS–MS. Acetochlor was taken as surrogate, and alachlor as internal standard. SPE with different types of columns was compared with LLE (liquid-liquid extraction). Further, the breakthrough volume for different pesticides was determined. The results showed that the selected pesticides can be determined very sensitively with LC–MS–MS. The minimum detectable quantity (MDQ) for each pesticide was about 1.0 ng. To date, SPE cartridge studies showed that the Oasis HLB cartridges were suitable for further studies. However, for Oasis HLB cartridge, different pesticide showed different breakthrough volume. The results showed that for acephate and methamidophos, the breakthrough volume was about 30 mL of water sample, much less than the breakthrough volume of other pesticides studied. Because of the higher vapor pressure and higher Henry's constant of methamidophos, dimethoate and carbofuran, much attention should be paid on their losses in the evaporation step of the experiment. This analytical method can be applied to determine pesticide contamination in environmental water samples. Revised: 12 September 2005 and 21 October 2005     

Determination of organophosphorus pesticides by gas chromatography with mass spectrometry using a large‐volume injection technique after magnetic extraction

A fast and efficient method was developed for the extraction and determination of organophosphorus pesticides in water samples. Organophosphorus pesticides were extracted by solid‐phase extraction using magnetic multi‐walled carbon nanotubes and determined by gas chromatography with ion‐trap mass spectrometry. Parameters affecting the extraction were investigated. Under optimum conditions of the method, 10 mg magnetic multi‐walled carbon nanotubes were added into 10 mL sample. After 2 min, adsorbent particles settled at the bottom of test tube with a magnet. After removing aqueous supernatant, the analytes were desorbed with acetonitrile. Then, 70 μL of acetonitrile phase was injected into the gas chromatography and mass spectrometry system that had an ion‐trap analyzer. To achieve high sensitivity, the large‐volume‐injection technique was used with a programmed temperature vaporization inlet, and the ion‐trap mass spectrometer was operated in single ion storage mode. Under the best conditions, the enrichment factors and extraction recoveries were in the range of 113–124 and 74–103%, respectively. The limits of detection were between 3 and 15 ng/L, and the relative standard deviations were < 10%. This method was successfully used for the determination of organophosphorus pesticides in dam water, lagoon water, and river water samples with good reproducibility and recovery.     

Selective solid-phase extraction of bisphenol A using molecularly imprinted polymers and its application to biological and environmental samples

Molecularly imprinted polymers (MIPs) were prepared using bisphenol A (BPA) as a template by precipitation polymerization. The polymer that had the highest binding selectivity and ability was used as solid-phase extraction (SPE) sorbents for direct extraction of BPA from different biological and environmental samples (human serum, pig urine, tap water and shrimp). The extraction protocol was optimized and the optimum conditions were as follows: conditioning with 5 mL methanol–acetic acid (3:1), 5 mL methanol, 5 mL acetonitrile and 5 mL water, respectively, loading with 5 mL aqueous samples, washing with 1 mL acetonitrile, and eluting with 3 mL methanol. MIPs can selectively recognize, effectively trap and preconcentrate BPA over a concentration range of 2–20 μM. Recoveries ranged from 94.03 to 105.3 %, with a relative standard deviation lower than 7.9 %. Under the optimal condition, molecularly imprinted SPE recoveries of spiked human serum, pig urine, tap water and shrimp were 65.80, 82.32, 76.00 and 75.97 %, respectively, when aqueous samples were applied directly. Compared with C18 SPE, a better baseline, better high-performance liquid chromatography separation efficiency and higher recoveries were achieved after molecularly imprinted SPE.      

Application of fabric phase sorptive extraction with gas chromatography and mass spectrometry for the determination of organophosphorus pesticides in selected vegetable samples

In the present work, a high‐efficiency and solvent minimized microextraction technique, fabric phase sorptive extraction followed by gas chromatography and mass spectrometry analysis is proposed for the rapid determination of four organophosphorus pesticides (terbufos, malathion, chlorpyrifos, and triazofos) in vegetable samples including beans, tomato, brinjal, and cabbage. Fabric phase sorptive extraction combines the beneficial features of sol‐gel derived microextraction sorbents with the rich surface chemistry of cellulose fabric substrate, which collectively form a highly efficient microextraction system. Fabric phase sorptive extraction membrane, when immersed directly into the sample matrix, may extract target analytes even when high percentage of matrix interferents are present. The technique also greatly simplifies sample preparation workflow. Most important fabric phase sorptive extraction parameters were investigated and optimized. The developed method displayed good linearity over the concentration range 0.5–500 ng/g. Under optimum experimental conditions, the limits of detection were found in the range of 0.033 to 0.136 ng/g. The relative standard deviations for the extraction of organophosphorus pesticides were < 5%. Subsequently, the new method was applied to beans, tomato, brinjal, and cabbage samples. The results from the real sample analysis indicate that the method is green, rapid, and economically feasible for the determination of organophosphorus pesticides in vegetable samples.     

Determination of Organophosphorus Pesticides in Soybean Oil, Peanut Oil and Sesame Oil by Low-Temperature Extraction and GC-FPD

A low-temperature clean-up method for residue determination was developed and validated for 14 organophosphorus pesticides in soybean oil, peanut oil and sesame oil by gas chromatography with flame photometric detector (GC-FPD). A different matrix influenced the response and retention time of pesticides. Hence matrix-matched calibration standards were used to counteract the matrix effect. The pesticide responses in blank samples of soybean oil, peanut oil and sesame oil were within the linear range of 0.02–1 mg kg⁻¹ and the correlation coefficients were higher than 0.9989. Average recoveries obtained from different oil samples at three fortified levels were higher than 50% with relative standard deviations (RSDs) of less than 15%. The limit of detections (LODs) of studied pesticides ranged from 2 to 5 μg kg⁻¹. Thirty-nine commercial samples were analyzed, and the results were confirmed by gas chromatography–mass spectrometry (GC–MS) in selective ion monitoring (SIM) mode.     

An improved HPLC-ED method for monitoring plasma levels of clozapine and its active metabolites in schizophrenic patients

Summary An HPLC method with electrochemical detection has been developed for the determination of clozapine and its main metabolites, desmethylclozapine and clozapine N-oxide, in human plasma. An accurate pretreatment of the biological samples was implemented by means of solid phase extraction (SPE) on HLB cartridges. This improved pretreatment, together with a new mobile phase, allows for the accurate determination of clozapine N-oxide, which could not be quantitated by a previous method. The method uses only 100 μL of plasma for one complete analysis and shows good recovery values for all three analytes. The eluates from the SPE procedure were chromatographed in a reversed phase C18 column using a mobile phase composed of phosphate buffer, acetonitrile and methanol. Clozapine, desmethylclozapine and clozapine N-oxide were eluted in less than 10 minutes, without any interference from the biological matrix. Linearity was observed over the 2.50–150 ng mL⁻¹ (clozapine and desmethylclozapine) or 1.25–75 ng mL⁻¹ clozapine N-oxide) range for the three analytes, with satisfactory repeatability values. The limit of detection was 0.3 ng mL⁻¹ for clozapine and desmethylclozapine, samples of patients treated with Leponex gave good results. No interference from other common central nervous system drugs was found. This method seems to be a useful tool for pharmacokinetic studies and for clinical monitoring, because of its need for small plasma samples and its high sensitivity and selectivity.     

Membrane-assisted solvent extraction coupled to large volume injection–gas chromatography–mass spectrometry for the determination of a variety of endocrine disrupting compounds in environmental water samples

Membrane-assisted solvent extraction coupled to large volume injection in a programmable temperature vaporisation injector using gas chromatography–mass spectrometry analysis was optimised for the simultaneous determination of a variety of endocrine disrupting compounds in environmental water samples (estuarine, river and wastewater). Among the analytes studied, certain hormones, alkylphenols and bisphenol A were included. The nature of membranes, extraction solvent, extraction temperature, solvent volume, extraction time, ionic strength and methanol addition were evaluated during the optimisation of the extraction. Matrix effects during the extraction step were studied in different environmental water samples: estuarine water, river water and wastewater (influent and effluent). Strong matrix effects were observed for most of the compounds in influent and effluent samples. Different approaches were studied in order to correct or minimise matrix effects, which included the use of deuterated analogues, matrix-matched calibration, standard addition calibration, dilution of the sample and clean-up of the extract using solid-phase extraction (SPE). The use of deuterated analogues corrected satisfactorily matrix effect for estuarine and effluent samples for most of the compounds. However, in the case of influent samples, standard addition calibration and dilution of the sample were the best approaches. The SPE clean-up provided similar recoveries to those obtained after correction with the corresponding deuterated analogue but better chromatographic signal was obtained in the case of effluent samples. Method detection limits in the 5–54 ng L⁻¹ range and precision, calculated as relative standard deviation, in the 2–25% range were obtained.     

HPLC determination of pesticides in green bean samples after SPE clean-up

Summary A reversed-phase high performance liquid chromatographic (HPLC) method with an acetonitrile-methanol-water mobile phase gradient and photodiode-array detection (DAD) is described for simultaneous determination of 21 pesticides, frequently used in agriculture, of different types, namely organophosphorus, organochlorine,N-methylcarbamates, triazines and phenylureas in vegetable samples. The pesticides were extracted with acetone and then partitioned from the vegetable sample with dichloromethane. Sample clean-up was accomplished by solid-phase extraction (SPE) using both C₁₈ and florisil SPE columns. Average recoveries from green beans ranged from 70.0 to 110.1%. Detection limits of less than 0.1 mg kg^–1 were obtained.     

Analysis of insecticides in honey by liquid chromatography-ion trap-mass spectrometry: comparison of different extraction procedures

The feasibility of different extraction procedures was tested and compared for the determination of 12 organophosphorus and carbamates insecticides in honey samples. In this sense, once the samples were pre-treated - essentially dissolved in hot water by stirring - and before they could be analyzed by liquid chromatography-ion trap-second stage mass spectrometry (LC-MS(2)), four different approaches were studied for the extraction step: QuEChERS, solid-phase extraction (SPE), pressurized liquid extraction (PLE) and solid-phase microextraction (SPME). The main aim of this work was to maximise the sensitivity of pesticides and to minimise the presence of interfering compounds in the extract. All pesticides were linear in the range from CC(β) to 1000× CC(β) for the four extraction methods (three orders of magnitude). Detection capabilities (CC(β)) were 0.024-1.155 mg kg(-1) with QuEChERS, 0.010-0.646 mg kg(-1) with SPE, 0.007-0.595 mg kg(-1) with PLE, and 0.001-0.060 mg kg(-1) with SPME. All the target compounds could be recovered by any of the methods, at a CC(β) fortification level ranged from 28 to 90% for the SPME. In comparison, the PLE method was the most efficient extraction method with recoveries from 82 to 104%. It was followed by the QuEChERS method with recoveries between 78 and 101% and the SPE method with recoveries between 72 and 100%. The repeatability expressed as relative standard deviation (RSDs) was below 20% for all the pesticides by any of the tested extraction methods. Results obtained applying the four extraction techniques to real honey samples are analogous.     

High performance liquid chromatography–tandem mass spectrometry for the analysis of 10 pesticides in water: A comparison between membrane-assisted solvent extraction and solid phase extraction

This work describes the application of two sample preparation methods: membrane-assisted solvent extraction (MASE) and solid phase extraction (SPE) in combination with high performance liquid chromatography–tandem mass spectrometry (HPLC–MS–MS) for the determination of 10 pesticides in surface and ground water. Optimal extraction conditions for MASE were 60 min extraction time at 30 °C with a solvent volume of 100 μL toluene. 5 μL of the toluene extract were directly injected in the HPLC–MS–MS system. Concerning SPE, two materials were tested and C18 was superior to Oasis HLB. Complete desorption was ensured by desorbing the SPE (C18) cartridge with 3 mL of an acetonitrile/methanol mixture (1:1). After evaporation, the extract was injected in the analytical system. Analyte breakthrough was not found for the investigated compounds. For both methods, high extraction yields were achieved, in detail 71% (metalaxyl) till 105% (linuron) for MASE and 52% (ethiofencarb) till 77% (prometryne) for SPE (C18). Detection limits were in the low ng/L range for both methods and precision, expressed as the relative standard deviation (RSD) of the peak areas was below 13%. Five real water samples were analyzed applying both extraction methods. The results were in good agreement and standard addition proved that no matrix effects (such as ion suppression) occurred. In this comparison SPE has the potential of larger sensitivity whereas faster analysis and slightly better recoveries were achieved with MASE. MASE shows potential to be a promising alternative to the conventional off-line SPE concerning low to medium polar compounds.     

Bamboo Charcoal as Solid-Phase Extraction Adsorbent for the Determination of Organophosphorus Pesticides in Water Samples by High-Performance Liquid Chromatography

In this paper, bamboo charcoal was successfully developed for the solid-phase extraction adsorbent for the determination of six organophosphorus pesticides in water samples. After the bamboo charcoal was pretreated and packed in the solid-phase extraction cartridge, the organophosphorus pesticides in water samples were carried out the solid-phase extraction. To establish a perfect solid-phase extraction procedure, the experimental conditions including the eluent, eluent volume, pH of the sample, flow rate of the sample, and loading volume of the sample were all investigated. When 100 mL water samples in the pH range of 6–7 were loaded with the flow rate of 2.5 mL · min^?1 and then eluted with 10 mL acetonitrile, the proposed extraction method was validated by the recovery, correlation coefficient (R²), repeatability (RSD, n = 7) and LODs, which were 69.6–93.4%, 0.9982–0.9998, 2.9–5.6%, and 0.08–1.04 µg · L^?1, respectively. Furthermore, the analysis of the tap, snow, and river water samples demonstrated the feasibility of the proposed SPE method for real water samples. Based on the aforementioned factors, it could be concluded that bamboo charcoal was a good solid-phase extraction adsorbent, and this proposed solid-phase extraction method was suitable for the effective enrichment and determination of the organophosphorus pesticides in water samples.     

High-performance liquid chromatography–tandem mass spectrometry method for quantifying sulfonylurea herbicides in human urine: reconsidering the validation process

We have developed a method for measuring 17 sulfonylurea (SU) herbicides in human urine. Urine samples were extracted using solid phase extraction (SPE), preconcentrated, and analyzed by high-performance liquid chromatography–tandem mass spectrometry using turboionspray atmospheric pressure ionization. Carbon 13-labeled ethametsulfuron methyl was used as an internal standard. Chromatographic retention times were under 7 minutes. Total throughput was estimated as >100 samples per day. Because only one labeled internal standard was available for the analysis, we were forced to reconsider and restructure the validation process to include stringent stability tests and analyses of urine matrices of differing compositions. We describe our restructured validation process and the critical evaluation it provides for the method developed. The limits of detection (LOD) ranged from 0.05 μg/L to 0.10 μg/L with an average LOD of 0.06 μg/L. Average total relative standard deviations were 17%, 12% and 8% at 0.1 μg/L, 3.0 μg/L and 10 μg/L, respectively. Average extraction efficiencies of the SPE cartridges were 87% and 86% at 2.5 μg/L and 25 μg/L, respectively. Chemical degradation in acetonitrile and urine was monitored over 250 days. Estimated days for 10% and 50% degradation in urine and acetonitrile ranged from 0.7 days to >318 days. The influence of matrix effects on precision and accuracy was also explored. Electronic Supplementary Material Supplementary material is available for this article at For additional information, contact Anderson Olsson at     

Determination of olanzapine and desmethylolanzapine in the plasma of schizophrenic patients by means of an improved HPLC method with amperometric detection

Summary An improved HPLC method with electrochemical detection has been developed for the determination of olanzapine and its main metabolite, desmethylolanzapine, in human plasma. Chromatographic separation and analysis were performed on a C₈ reversed-phase column with a mixture of methanol, acetonitrile, and pH 3.7 phosphate buffer as mobile phase; 2-methylolanzapine was used as internal standard. Careful pretreatment of the plasma samples was implemented by means of solid phase extraction (SPE). Response was linearly dependent on concentration and precision was satisfactory over the concentration range 0.5–75.0 ng mL⁻¹ for both analytes. The limit of detection was 0.2 ng mL⁻¹ for both analytes. Application to plasma samples of patients treated with Zyprexa tablets gave good results. Because of its sensitivity and selectivity, and the need for small plasma samples, this method seems to be a useful tool for clinical monitoring.     

三维石墨烯金属网固相萃取测定有机磷农药残留

以金属网为基体材料,通过化学键合的方式将氧化石墨烯和Au纳米颗粒层层组装到金属网表面,得到一种Au纳米颗粒改性的石墨烯气凝胶修饰的金属网萃取材料,并应用于有机磷农药的富集检测.与商用的萃取材料进行对比,相较于SAX、C18、-NH2、Carb、Florisil等材料,金纳米颗粒改性的三维石墨烯气凝胶金属网对有机磷农药分...     

Multiresidue procedures for determination of triazine and organophosphorus pesticides in water by use of large-volume PTV injection in gas chromatography

Summary Two procedures, based on large-volume injection with a programmed-temperature vaporizer (PTV), have been developed for the determination of several triazine and organophosphorus pesticides. The use of PTV for injection in gas chromatography (GC) has enabled the introduction of up to 200 μL sample extract into the GC, thus increasing the sensitivity of the method. PTV injection has been combined off-line with two different microextraction procedures—liquid-liquid partition and solid-phase extraction. A simple and rapid off-line liquid-liquid microextraction procedure (5 mL water/1 mL methyltert-butyl ether) was applied to surface water samples spiked at levels between 0.01 and 5μg L⁻¹. Recoveries of the overall procedure were >80% and the precision was better than 15%. Detection limits were <30 ngL⁻¹ from 200-μL injections in GC-NPD analysis of triazines and GC-FPD analysis of organophosphorus pesticides. Off-line automated solid-phase extraction with C₁₈ cartridges has been applied to water samples (50 mL) spiked at 0.01, 0.1 and 1 μg L⁻¹. The overall procedure was satisfactory (recoveries >80% and coefficients of variation <12%) and the limits of detection ranged from 1 to 9 ng L⁻¹. Finally, several surface water samples were anlysed, and triazine herbicides were detected at concentrations of approx. 0.1–0.2 μg L⁻¹. The results were similar to those obtained by conventional solvent extraction then GC-MSD after splitless injection of 2 μL.     

Determination of Organophosphorus Pesticides in Soil by MMSPD-GC-NPD and Confirmation by GC-MS

A novel method, modified matrix solid-phase dispersion (MMSPD), has been developed for quantitative analysis of organophosphorus pesticide residues in soil. It was based on matrix solid-phase dispersion (MSPD) and continuous liquid-solid extraction (continuous LSE), using Florisil as sorbent and dichloromethane as the recycling solvent. Two soils with different texture and physicochemical properties were studied to validate the method. The effect of residence time of pesticides in soil was also studied. MMSPD was compared with MSPD and continuous LSE respectively. Determination was carried out by gas chromatography with nitrogen-phosphorus detection (GC-NPD). The method gave recoveries ranging from 72–105% with relative standard deviations (RSDs) lower than 15% for the pesticides studied. The limits of detection (LODs) ranged from 0.1 to 0.6 ng g⁻¹. Two pesticide residues have been detected in real soil samples from Fujian, China, using MMSPD. The pesticides were confirmed by gas chromatography-mass spectrometry (GC-MS) in a selected-ion monitoring (SIM) mode. Revised: 4 and 9 April 2006