惰性盐辅助合成介孔石墨化碳片及其电容性能

以惰性盐KCl为模板、硝酸镍为金属催化剂镍源、葡萄糖为碳源,通过碳化处理制备了介孔石墨化碳片。利用扫描电子显微镜、透射电子显微镜、X-射线衍射仪和比表面测试仪对介孔石墨化碳片进行了表征。探讨了碳片形成的机理,采用三电极测试体系研究了介孔石墨化碳片电极材料的电化学性能。结果表明,10gKCl制备的碳片比表面积最大（989m²·g^-1）,在6mol·L^-1KOH电解液中,当电流密度为0.5A·g^-1时,比电容达到180F·g^-1;当电流密度达到10A·g^-1时,比电容维持在148F·g^-1,显示了电极具有较好的倍率性能;在10A·g^-1条件下,2000次循环充放电测试后电容没有发生衰减,展示了在超级电容器方面的应用潜力。     

溶剂热法合成蜂巢状氧化镍及其电化学电容性能

利用N，N-二甲基甲酰胺(DMF)为溶剂的溶剂热法制备了蜂巢状氧化镍，反应过程中DMF既做溶剂又做沉淀剂。研究了不同制备条件对NiO形貌及电化学性质的影响，并用X-射线衍射(XRD)、扫描电子显微镜(SEM)以及循环伏安(CV)技术进行了表征。结果表明，300 ℃热处理得到的氧化镍，10 mA电流下单电极比电容达460 F·g^-1。     

HY分子筛为模板合成的微孔炭及其电化学电容性能

以HY分子筛为模板, 采用糠醇浸渍炭化法和糠醇浸渍-乙腈气相沉积炭化法制备了多种微孔炭材料, 分别标记为PFA系列和AN系列, 并研究了其电化学电容性能. X射线衍射(XRD)测试表明AN系列炭材料较好地复制了HY分子筛模板的孔结构有序性. X射线光电子能谱仪(XPS)测试表明, 乙腈气相沉积在炭材料中引入丰富的含氮官能团. 氮气吸附测试表明, 炭材料是典型的微孔材料, 具有较高的比表面积, 较窄的孔径分布范围. 电化学测试表明, AN系列炭材料电容性能较好, 并具有明显的赝电容, 其中AN8的比电容最大可达210 F·g^-1. AN系列炭材料的电容保持率与材料的导电性和介孔率有关.     

无模板剂合成用于超级电容器的二氧化锰/石墨烯复合材料

以尿素、四水合氯化锰和氧化石墨烯为原料,采用水热法并通过热分解制备了一种具有石墨烯包覆结构的石墨烯-二氧化锰复合材料,利用扫描电子显微镜、X射线衍射、比表面积（BET）、拉曼光谱和热失重等技术对其形貌、晶体结构及表面结构进行了表征;在三电极条件下利用循环伏安法、恒流充放电法和交流阻抗法测试了材料的电化学性能,并考察了不同石墨烯含量对材料比电容的影响. 结果表明,在不添加模板剂的条件下制备的复合材料中二氧化锰是具有介孔结构的α-MnO₂,当复合15%（质量分数）的石墨烯后材料的比表面积从109 m²·g^-1提高到168 m²·g^-1. 复合材料具有更好的电化学性能,在0.2 A·g^-1电流密度下复合材料的比电容达到最大值（454 F·g^-1）,远高于纯二氧化锰的值（294 F·g^-1）. 在2 A·g^-1的电流密度下恒流充放电2000 次后复合材料的比电容保持率为92%.     

介孔碳/石墨烯复合材料的制备及其醌类改性电容性能

首先利用硬模板法制备出介孔碳/石墨烯复合材料,然后向复合材料中引入具有赝电容活性的醌类分子进一步增大材料的电容性能。研究结果表明,负载30%（w/w）叔丁基氢醌的介孔碳/石墨烯复合材料具有最佳的电容性能,在电流密度为0.5 A·g^-1时,比电容值为355 F·g^-1;当电流密度高达30 A·g^-1时,其比电容值高达226 F·g^-1,比电容保持率为64%,表现出良好的速率特性。     

NiO/MnO2分级纳米片阵列复合材料的制备与超电容性能

通过化学浴沉积和水热法在泡沫镍上制备了NiO/MnO₂分级纳米片阵列复合材料,XRD和SEM测试表明NiO纳米片垂直生长在泡沫镍上,交叉形成网状阵列结构;MnO₂纳米介孔泡沫进一步生长在NiO纳米片两侧,与NiO形成了壳核式的复合结构。循环伏安和恒流充放电测试发现,NiO/MnO₂分级纳米片阵列复合材料的电化学性能相比复合前得到明显改善,在1 A·g^-1的电流密度下,比电容提高至1 297 F·g^-1;2 A·g^-1下循环1 000次,比电容保持率高达97%,比电容和循环性能的改善是由于分级纳米片阵列复合结构方便了电解液传质,扩大了活性材料与电解液的接触,促进了赝电容反应,提高了NiO和MnO₂的结构稳定性。     

MCM-41负载S2O82-/TiO2固体超强酸的制备和酯化性能研究

采用液相沉积法制备了由MCM-41介孔分子筛负载S₂O₈^2-/TiO₂的固体超强酸催化剂。探讨了成酸机理，并以乙酸和异戊醇的酯化反应作为探针反应考察了焙烧温度、浸渍溶液浓度等制备条件对催化剂催化活性的影响，得到了较佳的制备条件。XRD、N₂吸附-脱附和FTIR结果表明，固体超强酸保持了MCM-41的介孔结构，BET表面积高达211 m²·g^-1，且具有强酸性(H_o<-12.70)。     

氮掺杂介孔碳的制备及其电化学超电容性能

通过直接炭化沸石咪唑酯骨架结构材料（ZIF-8）纳米多面体,成功制备了氮掺杂介孔碳（NMCs）. 采用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线衍射（XRD）、拉曼光谱、X射线光电子能谱（XPS）及比表面和孔隙度分析仪对其微观形貌和结构进行了表征,并对NMCs的电化学超电容性能进行了测试. 结果表明：NMCs具有规整的形貌、介孔纳米结构和较大比表面积（2737 m²·g^-1）;由于氮元素掺杂所赋予的优异的表面润湿性和赝电容性能,且介孔结构有利于电解质到达电极活性材料表面,NMCs表现出优异的电化学超电容性能,在1 A·g^-1的电流密度下,1.0 mol·L^-1H₂SO₄溶液中的比电容值为307 F·g^-1,并具有良好的功率特性;此外,在10A·g^-1的大电流密度下充放电循环5000次后,NMCs的比电容值保持率为96.9%.     

介孔氧化钨电色薄膜的制备与性能研究

采用一种新的非离子型gemini表面活性剂结构导向模板, 成功制备了介孔氧化钨薄膜. 通过SAXRD, TEM和N₂吸附-脱附等方法考察薄膜的制备和微结构特性, 发现获得的产物具有三维蠕虫介孔结构, 比表面积可达145.5 m²• g^－1. 测定了该薄膜在无水高氯酸锂/碳酸丙烯酯电解质溶液中的循环伏安和电致变色性能, 并与无模板薄膜进行了对比研究. 研究表明, 由于具有更大的电化学活性比表面, 纳米介孔氧化钨薄膜表现出增强的电色性能, 在633 nm波长处的透过率调制幅度可达60%以上, 着色效率为51.7 cm²•C^－1.     

低成本硫掺杂多孔碳材料的制备及其超级电容性能

以廉价的胶态二氧化硅为模板,蔗糖为碳源,硫酸为预碳化试剂和硫源,通过硬模板法制备了相对廉价的硫掺杂多孔碳(SSC-T,T℃代表碳化温度)材料。采用多种表征方法对多孔碳材料的微观形貌、孔道结构、比表面积和表面硫物种进行了表征,探究了硫酸和碳化温度对多孔碳材料的微观形貌、孔道结构和比表面积的影响。结果表明,碳化温度对碳的孔结构、比表面积和硫元素的含量有显著的影响,其中900℃碳化得到的样品SSC-900具有最大的比表面积、孔体积和比电容,远高于未加入硫酸制备的碳材料SC-900,表明硫酸的加入可以提高碳材料的比表面积、孔体积,进而提高碳材料的比电容。与昂贵的有序介孔碳CMK-3相比,SSC-900具有成本更低、孔径更大和电容性能更好的优点。在以6.0 mol·L^-1 KOH为电解质的三电极体系中,在0.5 A·g^-1的电流密度下,SSC-900的比电容可以达到357 F·g^-1,而SC-900和CMK-3的比电容分别仅为152和266 F·g^-1。电容贡献分析表明,SSC-900的双层电容值和赝电容值均高于SC-900。此外,SSC-900在0.5 A·g^-1的电流密度下循环10 000次后仍能保持98.4%的初始比电容。     

Synthesis of mesoporous NiO with crystalline walls by a simple sol–gel route

Mesoporous NiO particles with crystalline walls were prepared by a simple sol-gel technique. X-ray diffraction (XRD), N₂ adsorption–desorption, field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) have been used to investigate the mesoporous NiO particles. The as-prepared mesoporous NiO possessed narrow pore in the range of mesopores and was stable up to 700 ^oC. Various characterization results showed that the mesostructure was formed through the aggregation of nanocrystals and stearic acid in the precursor played an important role in formation of the final mesoporous structures. Mesoporous Ni particles have also been successfully synthesized by reduction of the obtained mesoporous NiO at 700 ^oC for 30 min.     

Amphiphilic block copolymers directed synthesis of mesoporous nickel-based oxides with bimodal mesopores and nanocrystal-assembled walls

Mesoporous late-transition metal oxides have great potential in applications of energy,catalysis and chemical sensing due to their unique physical and chemical properties.However,their synthesis via the flexible and scalable soft-template method remain a great challenge,due to the weak organic-inorganic interaction between the frequently used surfactants(e.g.,Pluronic-type block copolymers) and metal oxide precursors,and the low crystallization temperature of metal oxides.In this study,ordered mesoporous NiO with dual mesopores,high surface area and well-interconnected crystalline porous frameworks have been successfully synthesized via the facile solvent evaporation-induced co-assembly(EICA) method,by using lab-made amphiphilic diblock copolymer polystyrene-b-poly(4-vinylpyridine)(PS-b-P4 VP) as both the structure-directing agent(the soft template) and macromolecular chelating agents for nickel species,THF as the solvent,and nickel acetylacetonate(Ni(acac)2) as inorganic precursor.Similarly,by using Ni(acac)2 and Fe(acac)3 as the binary precursors,ordered mesoporous Fedoped NiO materials can be obtained,which have bimodal mesopores of large mesopores(32.5 nm) and secondary mesopores(4.0-11.5 nm) in the nanocrystal-assembled walls,high specific surface areas(～74.8 m~2/g) and large pore value(～0.167 cm~3/g).The obtained mesoporous Fe-doped NiO based gas sensor showed superior ethanol sensing performances with good sensitivity,high selectivity and fast response-recovery dynamics.     

Enhanced Electrochemical Capacitive Properties of Nickel‐Cobalt Oxide Nano‐flakes Materials

Nickel‐cobalt oxide nano‐flakes materials are successfully synthesized by a facile chemical co‐precipitation method followed by a simple calcination process. The studies show that the as‐prepared nickel‐cobalt oxides with different Ni/Co ratio are composed of NiO and Co₃O₄ compounds. The Co_0.56Ni_0.44 oxide material, which exhibits a mesoporous structure with a narrow distribution of pore size from 2 to 7 nm, possesses markedly enhanced charge‐discharge properties at high current density compared with the pure NiO and pure Co₃O₄. The Co_0.56Ni_0.44 oxide electrode shows a specific capacitance value of 1227 F/g at 5 mA/cm², which is nearly three times greater than that of the pure NiO electrode at the same current density.     

半晶化双螺旋介孔MnO2的合成和电化学性质

Mesoporous silica KIT-6 has novel three-dimensional gyroidal channel structure, space group of 1a-3d, and ordered tunable pores up to 10 nm. In this paper, such mesostructured silica was employed as hard template to prepare semicrystalline gyroidal mesoporous MnO2. The structure was investigated by XRD, TEM and HRTEM, and found to be of high quality 1a-3d symmetry, in good accordance with the template structure. The material has a BET surface of 118 m2·g^-1 and pore volume of 0.35 cm3·g^- 1 after eliminating template. Mesoporous MnO2 has shown good electrochemical property as supercapacitor material in 1 mol·L^-1 Na2SO4 and 1 mol·L^-1 LiClO4 solutions, but interesting pseudocapacitance behavior was observed in the case of 6 mol·L^-1 KOH. It was found that mesoporous MnO2 performed stable reversible electrochemical behavior with capacitance of 220 F·g^-1 in a potential range of -0.1-0.55 V vs. Hg/HgO in alkaline solution, demonstrating that it is a promising novel electrode material for the fabrication of electrochemical capacitors.     

介孔炭的直接制备及其电化学性能研究

以柠檬酸镁为原料,采用直接碳化法制备介孔炭电极材料。N2吸附测试表明,所制备多孔炭的比表面积达2 000 m2·g-1左右,介孔孔容和平均孔径随着炭化温度的升高而增加,当炭化温度大于800℃时,能够制备出以介孔结构为主的多孔炭材料。电化学测试表明,MgC-800和MgC-900具有优异的电化学电容特性。与硬模板法制备的OMC相比,MgC-800和MgC-900在实验电流密度范围内具有更大的比电容值,这应当归功于它们巨大的比表面积以及有利于电解质离子扩散的介孔结构。     

The preparation of nickel oxide based on infinite dilute method and its electrochemical performance

With NaOH as precipitation agent and NiSO₄ · 6H₂O as raw material, Ni(OH)₂ particles were synthesized by infinite dilute method and sintered at 300°C for NiO. The synthesized NiO particles with a structure of cubic crystalline phase are well dispersed and ball-flower like with a diameter of 500 nm. The electrochemical tests show that the NiO particles have relatively high capacitance and excellent capacitive retention. The good structure and excellent performance suggest its promising application in supercapacitors.     

Fabrication of a Hierarchical Ni(OH)2@Ni3S2/Ni Foam Electrode from a Prussian Blue Analogue-Based Composite with Enhanced Electrochemical Capacitive and Electrocatalytic Properties

Developing high-efficiency, cost-effective, and durable electrodes is significant for electrochemical capacitors and electrocatalysis. Herein, a 3D bifunctional electrode consisting of nickel hydroxide nanosheets@nickel sulfide nanocubes arrays on Ni foam (Ni(OH)₂@Ni₃S₂/NF) obtained from a Prussian blue analogue-based precursor is reported. The 3D higher-order porous structure and synergistic effect of different compositions endow the electrode with large specific surface area, facile ion/electron transport path, and improved conductivity. As a result, the Ni(OH)₂@Ni₃S₂/NF electrode exhibits a high specific capacity of 211 mA h g⁻¹ at a current density of 1 A g⁻¹ and 73 % capacity retention after 5000 cycles at 5 A g⁻¹. Moreover, the Ni(OH)₂@Ni₃S₂/NF electrode has superior electrocatalytic activity for the hydrogen evolution reaction with low overpotentials of 140 and 210 mV at current densities of 10 and 100 mA cm⁻², respectively. The synthetic strategy for the unique higher-order porous structure can be extended to fabricate other composite materials for energy storage and conversion.     

The Inherent Electrochemistry of Nickel/Nickel‐Oxide Nanoparticles

The direct detection of nanoparticles is at the forefront of research owing to their environmental and toxicological applications. Herein, we studied the inherent electrochemistry of Ni and NiO nanoparticles and proposed a simple and direct electrochemical method for the determination of the concentrations of both nickel (Ni) and nickel oxide (NiO) nanoparticles in alkaline solution. A highly sensitive voltammetry technique was used to measure the oxidative signal of Ni(OH)₂ that formed spontaneously on the surface of Ni and NiO nanoparticles in alkaline media. Detection limits of 220 μg mL^?1 for Ni and 13 μg mL^?1 for NiO nanoparticles were obtained. Ni and NiO nanoparticles are used as electrode modifiers or as electrochemical signal labels in various biosensing applications. Therefore, methods to rapidly quantify the amount of Ni and NiO nanoparticles are of widespread potential use.     

Nickel oxide/expanded graphite nanocomposite electrodes for supercapacitor application

Nickel oxide/expanded graphite (NiO/EG) nanocomposites with different loading of EG were prepared through chemically depositing Ni(OH)₂ in EG followed by thermal annealing and characterized by scanning electron microscopy (SEM), powder X-ray diffraction (XRD), Brunauer–Emmet–Teller (BET) isotherm and electrochemical measurements. The prepared NiO/EG composites were found to be crystalline and highly porous with high specific surface area and pore volume. SEM analysis reveals uniform porous morphology for NiO in the NiO/EG-60 nanocomposites which shows good specific capacitance (510?F?g^?1) at a current density of 100?mA?g^?1 in 6?mol?L^?1 KOH measured by chronopotentiometry employing a three-electrode system. The specific capacitance retention of the NiO/EG-60 nanocomposites was found to be ca. 95% after 500 continuous galvanostatic charge–discharge cycles, indicating that the NiO/EG nanocomposites can become promising electro-active materials for supercapacitor application.     

Mesoporous MgO: Synthesis,physico-chemical,and catalytic properties

Mesoporous MgO was obtained via the hydrothermal synthesis using both ionogenic and non-ionogenic surfactants as structure-directing templates. The materials prepared were characterized by SEM, BET-N₂, XRD, and TG-DTA techniques. MgO particles are spherical 20-μm aggregates of primary oxide particles well shaped as rectangular parallelepipeds. Magnesium oxide samples have the specific surface area of 290–400 m²/g and pore sizes of 3.3–4.1 nm. Their mesoporous structure remained unchanged after calcination up to 350°C. Catalytic activity of mesoporous MgO was studied in acetone condensation reaction.