苯乙烯与富马酸二甲酯的原子转移自由基无规共聚

2-溴丙酸乙酯(EBP)为引发剂,CuBr为催化剂,N,N,N′,N″,N″-五甲基二亚乙基三胺(PMDETA)为配位剂的富马酸二甲酯(DMF)与苯乙烯(St)的原子转移自由基无规共聚合,转化率低于60％时,1n([M]0／[M])随聚合时间线性增加,数均分子量(Mn)随转化率性增长,所得聚合物分子量分布(PDI)较窄。根据元素分析所得共聚物的平均组成,由Kelerr—Tudos方程,计算两种共聚单体的竞聚率分别是rst=0．488,rDMF=0．303。并探讨了单体与引发剂配比以及温度对聚合反应的影响。     

4-乙烯基吡啶-氯化锌络合物与电子给体单体光照下共聚合研究

受电子单体4-乙烯基吡啶-氯化锌络合物(4-VP)_2ZnCl_2(M_1)可以和电子给体单体如苯乙烯(M_2)在365nm光照下共聚合。聚合是二者形成的基态电荷转移复合物(CTC)吸收光后产生自由基引发的。测得竞聚率为r_1=2.04,r_2=0.23。对溶剂极性的影响和(4-VP)_2Znal_2与其它电子给体单体光照下共聚合也作了研究。     

NaNO2/FeSO4存在下聚苯乙烯大分子引发剂的合成及嵌段共聚

用NaNO2/FeSO4·7H2O体系替代TEMPO在有机相中合成分子量可控的聚苯乙烯大分子引发剂,引发苯乙烯聚合及酯类单体[如甲基丙烯酸甲酯(MMA)、丙烯酸甲酯(MA)和丙烯酸乙酯(EA)等]聚合,得到两嵌段共聚物.其多分散性指数小于1.5,体现了可控聚合的特征.用大分子引发剂引发苯乙烯进行活性链增长,单体的转化率较高.嵌段共聚物的实测分子量与理论分子量相近,结构经1HNMR和GPC表征.NaNO2/FeSO4·7H2O体系在纯有机相中的应用降低了活性聚合的成本,有利于工业化应用.     

乙烯基单体/N-取代马来酰亚胺共聚合动力学

详细研究了聚合温度、引发剂用量、单体配比对苯乙烯(St)/N-苯基马来酰亚胺(PMI)共聚合动力学的影响.对St、甲基丙烯酸甲酯(MMA)和丙烯腈(AN)等单一或混合单体与PMI、N-环己基马来酰亚胺(ChMI)和N-邻氯苯基马来酰亚胺(o-CPMI)的共聚合进行了研究,并讨论了单体结构的影响.     

可聚合的光引发转移终止剂合成接枝共聚物

采用一种可聚合的光引发转移终止剂 ,2 N ,N 二乙基二硫代氨基甲酰氧基乙酸 β 甲基丙烯酰氧基乙酯 (MAEDCA) ,通过两种途径制备了含有聚甲基丙烯酸甲酯 (PMMA)和聚苯乙烯 (PSt)链段的接枝共聚物 .其一是将MAEDCA作为引发剂 ,在紫外光照射下引发MMA聚合 ,得到大分子单体 ,通过大分子单体与St的共聚合得到 .考察了所用大分子单体的分子量和浓度对共聚合的影响 .其二是将MAEDCA作为单体与MMA共聚得到侧链上含有N ,N 二乙基二硫代氨基甲酰氧基 (DC)基团的无规共聚物 ,P(MMA co MAEDCA) .在紫外光照射下 ,P(MMA co MAEDCA)作为大分子引发剂引发St聚合 ,得到P(MMA co MAEDCA) g PSt的共聚物 ,研究了接枝共聚合过程的活性自由基聚合特征     

表面活性单体DMBAC光聚合动力学研究

采用偶氮二异丁脒盐酸盐(AIBA)作为光引发剂,光引发聚合并研究了阳离子表面活性单体——甲基丙烯酰氧乙基二甲基苄基氯化铵(DMBAC)的均聚及其与丙烯酰胺(AM)共聚合反应的动力学行为,聚合反应均在高于DMBAC临界胶束浓度(CMC)的条件下进行.研究结果显示DMBAC均聚合反应速率与引发剂浓度的0.29次方以及单体浓度的0.89次方成正比,均聚合反应的表观活化能约为13.74 kJ/mo1;DMBAC与AM共聚合反应速率与引发剂浓度的0.82次方以及单体总浓度的0.83次方成正比,共聚合反应的表观活化能约为10.97 kJ/mo1;同时测得DMBAC与AM共聚合反应的单体竞聚率为r₁=0.27(AM)、r₂=2.00(DMBAC),说明AM趋向于形成共聚物,而DMBAC更趋向于形成均聚物.     

异丁烯与对氯甲基苯乙烯正离子共聚合研究

以四氯化钛(TiCl4)、二氯乙基铝(AlEtCl2)、倍半铝(AlEt1.5Cl1.5)、三氯化铝(AlCl3)等路易斯酸为共引发剂,水或枯基醇(CumOH)为引发剂,在-80℃下的正己烷/二氯甲烷(V/V=6/4)的混合溶剂内,研究了异丁烯(IB)与对氯甲基苯乙烯(p-CMS)的正离子共聚合.利用示差凝胶渗透色谱仪(GPCRI)以及核磁氢谱(1H-NMR)对共聚物的表观分子量及分子量分布、共聚组成等进行分析,采用KelenTüd?s与Yezreielv-Brokhina-Roskin法计算了单体竞聚率,初步探讨了p-CMS与IB正离子共聚合的反应机理.结果表明,AlEtCl2、AlEt1.5Cl1.5、AlCl3均可催化大分子间的烷基化反应,产生凝胶;TiCl4作为共引发剂,可以得到无凝胶单峰分布共聚物;邻位氯甲基苯乙烯(o-CMS)不能参与共聚,p-CMS的共聚活性较低,IB与p-CMS的单体竞聚率为rIB=4.67,rp-CMS=0.70;随反应时间延长,共聚物中p-CMS的含量及共聚物分子量均逐渐增加;p-CMS单体自身几乎不参与引发,共聚到大分子链后,苄基氯缓慢参与引发,形成支化.提高共聚合温度至-60和-40℃,聚合速率降低,p-CMS的引发活性未发生明显变化.     

苯乙烯-对叔丁基苯乙烯-间戊二烯三元共聚物制备及表征北大核心CSCD

相对于异戊二烯和丁二烯传统二烯烃,新型间戊二烯单体可以通过阴离子共聚合实现特殊序列结构共聚物,如交替共聚物。本文以间戊二烯、苯乙烯和对叔丁基苯乙烯为共聚单体,通过丁基锂引发聚合合成系列二元及三元共聚物,重点考察了共聚动力学和共聚物的微观结构。实验结果表明:(1)聚合动力学显示共聚合符合经典一级反应特征,共聚单体可以转化完全;(2)核磁氢谱在线分析表明共聚单体等摩尔消耗,核磁氢谱和碳谱证明了二元交替共聚结构;(3)二元及三元共聚均具有明显的活性可控聚合特征,分子量与理论值高度吻合,分子量分布D均小于1.20;(4)示差扫描量热(DSC)结果显示交替共聚物是一类特殊的半结晶聚合物,玻璃化转变温度Tg可以通过调控共聚单体比例微调,Tm在100~120℃范围;(5)基于间戊二烯特殊的二元交替共聚,推测了可能的聚合机理。     

St/AN乳液共聚合的表观竞聚率和恒比组成

<正> 共聚合中竞聚率的正确测算对于研究共聚物组成与单体配料比及转化率的关系、共聚物组成分布及链段分布和共聚合机理都有重要意义。对于大多数二元自由基共聚体系,聚合方法不同对竞聚率无影响,但对某些聚合体系,如苯乙烯/丙烯腈,不同的聚合方法测得的“竞聚率”会有所不同。一般文献报道,苯乙烯/丙烯腈自由基共聚合,60℃下的竞聚率分别为r_st=0.41±0.08,r_(AN)=0.04±0.04,均系本体聚合的实验结果。为此,     

α-甲基苯乙烯与苯乙烯阴离子共聚合研究——Ⅰ.共聚反应动力学及机理

 本文研究了以正丁基锂为引发剂、四氢呋喃为极性添加剂、在环己烷中进行α-甲基苯乙烯与苯乙烯阴离子共聚合。通过共聚反应动力学的研究,提出了聚合机理,求得了两种单体通过不同聚合活性种增长反应及解聚反应的速度常数及活性种间的络合平衡常数。     

蓖麻油聚氨酯／聚取代乙烯互穿网络聚合物作为带锈涂料及粘合剂的可能性

在室温用氧化还原引发剂将蓖麻油、甲苯二异氰酸酯及取代乙烯合成了蓖麻油聚氨酯／聚取代乙烯互穿网络聚合物（ＩＰＮ），研究了不同组成对带锈铁板搭接剪切强度的影响。指出搭接剪切强度随取代乙烯均聚物的玻璃化温度增加而增。ＮＣＯ／ＯＨ之比愈大，搭接剪切强度也愈大。以蓖麻油聚氨酯／（丙烯腈－苯乙烯）共聚物的反应液作为带锈铁板的涂料，其涂膜性能良好。用扫描电镜观察了此种涂料与带锈铁板的结合状态，并讨论其成因。     

Radiation-induced copolymerization of hexafluoroacetone with 2-methyl-1-pentene

Copolymerization of hexafluoroacetone (HFA) with 2-methyl-1-pentene (2MP) in trichlorotrifluoroethane (R-113) was carried out by γ-ray irradiation in a low-temperature region of ?100 to 0°C. Though HFA does not homopolymerize and 2MP scarcely does, the copolymerization took place at various monomer compositions. The copolymerization rate and the molecular weight in the low-temperature region were much higher than those at 0°C. Above room temperature the copolymerization did not take place and only the adduct of monomers was formed. The copolymerization was inhibited to some extent by cation scavengers, but not by radical or electron scavengers. Elemental analysis and nuclear magnetic resonance (NMR) spectra show that the copolymer consists of almost equimolar monomer units and has two types of structure, head to tail and head to head or tail to tail. It has been concluded that copolymerization probably proceeds via a cationic mechanism to form an alternating copolymer.     

室温离子液体中的聚合反应

综述了近年来在室温离子液体中聚合反应的研究进展,特别是在配位聚合、自由基聚合、离子聚合及共聚反应,活性自由基聚合,电化学聚合等方面的进展情况;还介绍了离子液体在高分子材料方面的应用情况,展望了离子液体在该领域的应用前景.     

Radiation-induced solid-state copolymerization of maleic anhydride and acenaphthylene

Radiation-induced solid-state copolymerization of the maleic anhydride–acenaphthylene system was carried out for the purpose of studying the solid-state polymerization of vinyl compounds in a binary system. Melting point measurement confirmed that this binary monomer system forms a eutectic mixture in the solid state. The solid-state polymerization of these monomers proceeds at maximum rate at the eutectic composition, and the polymerization products consist of a mixture of polyacenaphthylene and 1:1 maleic anhydride–acenaphthylene alternating copolymer. Since the 1:1 copolymer was obtained in solution polymerization also and maleic anhydride did not homopolymerize in solid state, it is considered that the solid-state copolymerization of maleic anhydride and acenaphthylene occurs in a liquidlike state at the boundary of the two monomer crystals.     

Hybrid Copolymerization via the Combination of Proton Transfer and Ring-opening Polymerization

Phosphazene base,t-BuP2,was employed to catalyze the proton transfer polymerization(PTP)of 2-hydroxyethyl acrylate(HEA),and PTP was further combined with ring-opening polymerization(ROP)to exploit a new type of hybrid copolymerization.The studies on homopolymerization showed that t-BuP2 was a particularly efficient catalyst for the polymerization of HEA at room temperature,giving an excellent monomer conversion.Throughout the polymerization,transesterification reactions were unavoidable,which increased the randomness in the structures of the resulting polymers.The studies on copolymerization showed that t-BuP2 could simultaneously catalyze the hybrid copolymerization via the combination of PTP and ROP at 25°C.During copolymerization,HEA not only provided hydroxyl groups to initiate the ROP ofε-caprolactone(CL)but also participated in the polymerization as a monomer for PTP.The copolymer composition was approximately equal to the feed ratio,demonstrating the possibility to adjust the polymeric structure by simply changing the monomer feed ratio.This copolymerization reaction provides a simple method for synthesizing degradable functional copolymers from commercially available materials.Hence,it is important not only in polymer chemistry but also in environmental and biomedical engineering.     

电化学聚合漆酚钴膜配位结构与催化性能研究

电化学方法合成的聚合漆酚 (EPU)通过与氯化钴的异丙醇溶液作用 ,生成聚合漆酚钴配合物膜(EPU Co3+ ) .采用红外光谱、XPS光电子能谱、DTA TG、动态机械热分析 (DMTA)以及原子发射光谱 (AES)等手段进行表征 ,确定其配位结构 ,即每个钴离子与EPU中两个链节单元的羟基发生配位而交联 ,因此玻璃化转变温度和耐热性能均得到提高 .实验表明 ,此配合物膜在室温下的Na2 SO3水体系 (pH =7)中能催化引发VAc的聚合     

电化学聚合漆酚钴膜引发甲基丙烯酸甲酯（MMA）聚合的研究

利用电化学技术合成的聚合漆酚（EPU）与氯化钴的异丙醇溶液反应,得到电化学聚合漆酚钴配合物膜,经XPS光电子能谱、红外光谱、TG－DTA、动态机械热分析（DMTA）以及原子发射光谱（AES）等手段进行表征并确定其结构。由于每个钴离子与EPU分子中两个链节单元的羟基发生配位引进进一步交联。因此玻璃化转变温度和耐热性能均得到提高。实验表明,在常温下的Na2SO3水体系（pH值为7）中配合物膜能引发甲基丙烯酸甲酯（MMA）聚合。     

Room temperature synthesis and mechanical properties of two kinds of elastomeric interpenetrating polymer networks based on castor oil

Two kinds of interpenetrating polymer networks (IPNs) composed of two-component polyurethane (PU) and vinyl or methacrylic polymer (PV), namely, (polyether-castor oil)PU/PV IPN(I) and (polybutadiene-castor oil)PU/PV IPN(II), were synthesized at room temperature using benzoyl peroxide and N,N-dimethylaniline as redox initiator and dibutyltin dilaurate as catalyst. The former IPN was prepared by polymerization of castor oil, NCO-terminated polyether and vinyl or methacrylic monomer together and the latter IPN was obtained by polymerization of castor oil, NCO-terminated polybutadiene, NCO-terminated castor oil and vinyl or methacrylic monomer together. Various synthesis conditions affecting mechanical properties of the two kinds of IPNs were studied. Acrylonitrile (AN) is a good monomer for synthesizing IPN(I), but is a poor monomer for preparing IPN(II). At optimum conditions for the synthesis, both the (polyether-castor oil)PU/PAN IPNs and the (polybutadiene-castor oil)PU/polystyrene (PSt) IPNs possess permanent set about 10%, tensile strength over 13 and 11 MPa and ultimate elongation over 240% and 270%, respectively, thus behaving as elastomers. TEM micrograph of a (polybutadiene-castor oil)PU/PSt IPN showed a microphase separation in the IPN.     

环烷酸铕-环烷酸钠微乳体系的荧光光谱

许多萃取剂也是表面活性剂 ,在萃取过程中 ,涉及到反向胶团和微乳状液的形成、变和破坏等现象．研究含稀土反胶团和微乳状液中稀土离子的存在状态 ,了解稀土对微乳状液结构的影响 ,对了解稀土萃取过程的机制具有重要的意义［１］．我们曾应用多种手段 ,如红外光谱、核磁共振、小角Ｘ 射线衍射、激光光散射、透射电镜等 ,对皂化环烷酸／水／仲辛醇／正庚烷微乳体系的结构和性质进行了研究［２ -７］．在透射电镜下观察到皂化环烷酸体系形成的微乳状液结构呈球形 ,萃取稀土离子后 ,有机相中形成的聚集体颗粒在电镜下观察 ,离子的平均直径介于…     

Living polymerization and block copolymerization of alpha-olefins by an amine bis(phenolate) titanium catalyst

An amine bis(phenolate) dibenzyl titanium complex having a methoxy donor on a side arm leads, upon activation with tris(pentafluorophenyl)borane, to unique living properties in alpha-olefin polymerization: exceptionally high molecular weight poly(1-hexene) is obtained in a living fashion at room temperature, living polymerization of 1-hexene is obtained above room temperature, and block copolymerization of 1-hexene and 1-octene at room temperature is described as well.