Analysis of sulfur-containing compounds in crude oils by comprehensive two-dimensional gas chromatography with sulfur chemiluminescence detection

This paper reports an analytical method for separating, identifying, and quantifying sulfur-containing compounds in crude oil fraction (IBP-360 degrees C) samples based on comprehensive two-dimensional gas chromatography coupled with a sulfur chemiluminescence detector. Various sulfur-containing compounds and their groups were analyzed with one direct injection. 3620 peaks were detected including 1722 thiols/thioethers/ disulfides/1-ring thiophenes, 953 benzothiophenes, 704 dibenzothiophenes, and 241 benzonaphthothiophenes. The target sulfur compounds and their groups were identified based on the group separation feature and structured retention of comprehensive two-dimensional gas chromatography as well as standard substances. The quantitative analysis of major sulfur-containing compounds and total sulfur was based on the linear response of the sulfur chemiluminescence detector using the internal standard method. The sulfur contents of target sulfur compounds and their groups in 4 crude oil fractions were also determined. The recoveries for standard sulfur-containing compounds were in the range of 90-102%. The quantitative result of total sulfur in the Oman crude oil fraction sample was compared with those from ASTM D 4294 standard method (total S by X-ray fluorescence spectrometry), the relative deviation (RD%) was 4.2% and the precision of the method satisfactory.     

Synthesis of Cleavable Polymers via Oxidation of Thioether Moieties and Thiol Click Reactions: A Click-Declick Strategy

In the past decades click chemistries including thiol chemistries have found wide applications in the synthesis of well-defined polymers. In this research, a click-declick strategy based on the oxidation of heteroaromatic thioethers and the substitution reactions between the oxidized groups and thiols, is proposed for the synthesis of the cleavable polymers. In proof-of-concept experiments, block copolymers (BCPs) and star-like polymers are synthesized by thiol-phenylsulfone substitution reactions, and heteroaromatic thioethers are produced at the junction points of the BCP chains or on the crosslinking sites of the star-like polymer. The thioethers can be oxidized to heteroaromatic sulfoxides or sulfones, depending on the oxidization condition. It is demonstrated that both sulfoxides or sulfones can have base catalyzed nucleophilic substitution reactions with thiols, leading to the cleavage of the polymers.     

沥青质含量对渣油加氢转化残渣油收率和性质的影响

以塔河常渣脱沥青油掺兑不同含量的沥青质为原料,于高压釜反应器内进行加氢转化反应实验,考察沥青质含量对渣油加氢转化残渣油收率和性质的影响。研究结果表明,随原料中沥青质含量的增加,加氢残渣油的收率逐渐降低,加氢残渣油中的沥青质和焦炭产量之和与原料中沥青质含量的比值逐渐减小,在实验选定的条件下,高沥青质含量时沥青质更倾向于发生氢解反应生成小分子组分。与原料相比,反应后所得>350 ℃残渣油的平均相对分子质量、H/C摩尔比减小,密度增大,硫含量降低,氮含量增加,饱和分和沥青质含量增加,芳香分及胶质含量降低。随渣油中沥青质含量的增加,硫、氮脱除率先增加后降低。     

Use of sulfur derivatives as an ortho directing group for the metalation of diazines. Metalation of diazines. XVIII

The metalation of thioethers, methyl and phenyl sulfoxides and sulfones of pyrazine and pyridazine has been performed. Methyl sulfoxides and sulfones were first metalated on the methyl group. The ortho directing effect of thioethers, sulfoxides and sulfones have been compared with the methoxy group. The sulfoxides were shown to be very good ortho directing groups.     

催化柴油中硫化物的气相-原子发射光谱分析方法及应用

 建立了催化柴油馏分中各种硫化物类型分布的气相 原子发射光谱分析方法,考察了条件对各种硫化物分离的影响,定性(或归类)了催化柴油中的130多个硫化物,计算了程序升温条件下各种硫化物的保留指数,为不同实验室的定性比较和方法的转让提供了依据。硫化物中的硫在2mg/L～1000mg/L时其质量浓度与峰面积呈较好的线性关系,相关系数达0 997。几种硫化物(苯并噻吩、4 甲基苯并噻吩、二苯并噻吩、4 甲基二苯并噻吩、4,6 二甲基二苯并噻吩)6次测定所得峰面积的相对标准偏差均小于5 0%。当信噪比(S/N)为3时,测得苯并噻吩硫的检出限为0 1mg/L。     

柴油非加氢脱硫技术研究中样品的选择

利用气相色谱/原子发射光谱检测器（GC/AED），对小型加氢装置的加氢脱硫柴油样品及氧化/萃取前后样品油中含硫化合物进行了分析，对色谱图中出现的几个可疑峰进行了分析和推测，表明这几个峰是由元素硫产生的，并通过无硫油样中加入硫磺和对样品进行汞洗等实验进行了验证。此外，对于加氢柴油中元素硫产生原因以及对硫质量分数测定和对实验分析的影响，在氧化脱硫等非加氢脱硫实验中样品的选择等问题进行了讨论。     

Determining the antioxidant activities of organic sulfides by rotary bomb oxidation test and pressurized differential scanning calorimetry

Several typical sulfides were selected and dissolved in hydrotreated base oil, and the antioxidant activities of sulfides studied by rotary bomb oxidation test (RBOT), isothermal pressurized differential scanning calorimetry (PDSC) and non-isothermal PDSC. Four characteristic indexes of constant heating-rate PDSC were chosen and normalized to a comprehensive index by a new method. The sequence determined by the comprehensive index accords partly to the sequence determined by RBOT and accords well with the results reported. The antioxidant activity of sulfide increases with the number of sulfur atoms. Sulfide with long chain has good antioxidant activity, and the antioxidant activity of cyclic sulfides is poor. The method of normalizing the data is useful to determine the oxidation performances of samples, especially when the antioxidant activities vary greatly.     

原油中芳香硫化合物形态分布的研究

建立了原油中多环芳香硫化合物形态分布的研究方法。采用氯化钯/硅胶配位交换色谱分离原油中的芳香硫化合物,并用气相色谱/质谱分析、气相色谱-硫化学发光检测法结合色谱保留指数,鉴定出原油中的100多个多环芳香硫化物,包括含烷基取代基的苯并噻吩和二苯并噻吩类硫化物。定量分析表明,二苯并噻吩类化合物的含量占芳香硫化合物总量的91%左右。该方法可用于不同来源的原油中芳香硫化合物的形态分布研究。     

Determination of elemental sulfur by size-exclusion chromatography optimization and petrochemical applications

Factors affecting the elution of elemental sulfur beyond the total permeation limit of a size-exclusion chromatographic (SEC) column are investigated. The pore diameter of the column packing is found to be the most important parameter, and optimum results are achieved from a single 10³ Å pore polystyrene-divinylbenzene column with tetrahydrofuran as solvent. It is shown that both the column temperature and solvent flow-rate have little or no influence on the resolution of sulfur from other sample components. The apparent anomalous elution behavior of sulfur is validated by two independent approaches, and is addressed in terms of electronic interactions between sulfur and the phenyl ring of the polystyrene-divinylbenzene packing. The solubilities of sulfur in typical alkylate, naphtha and reformate samples at room temperature have been determined by the SEC method. The amounts of sulfur in typical hydrotreated cracked naphtha and gas oil samples from pilot unit runs have also been measured. These results are discussed in relation to relative solubilities of sulfur in compounds belonging to different hydrocarbon classes. Specifically, the solubility of sulfur is found to decrease with hydrocarbon type in the order, aromatics>naphthenes>olefins>n-alkanes>isoalkanes.     

Sulfoxides derived from Cinchona alkaloids—chiral ligands in palladium-catalyzed asymmetric allylic alkylation

Phenyl sulfides derived from Cinchona alkaloids, 9-PhS-epi-CD, 9-PhS-epi-QN, 9-PhS-epi-QD, and 9-PhS-QN were oxidized into the corresponding sulfoxides. Regardless of the oxidation system used (NaIO₄, TEMPO/NaOCl, VO(acac)₂/chiral Schiff base/H₂O₂) a similar stereochemical outcome of the oxidation was observed. Four pure epimers of sulfoxides 9-PhSO-epi-CD and 9-PhSO-epi-QN were isolated and fully characterized (X-ray, CD, ¹H NMR-pattern). The chiral sulfoxides as well as the corresponding sulfides and sulfones were tested in the Pd-catalyzed allylic alkylation of dimethyl malonate with rac-1,3-diphenyl-2-propenyl acetate. The sulfoxides obtained from Cinchona alkaloids bearing the additional stereogenic center gave the main product of configuration dependent on the chirality of alkaloid framework only. Similar ees (up to 60%) but significantly higher yields (90%) were obtained as compared to the reaction with the corresponding thioethers. The results were in agreement with nucleophilic attack directed at the allylic carbon located trans to the sulfur atom in the M-shaped intermediate η³-allylpalladium complex.     

Radical, one-step approach to o-chlorophenyl thioethers from xanthates. A rapid access to vinylsilanes

Xanthates have been readily converted into o-chlorophenyl thioethers using a one-step procedure conducted under radical conditions. In some selected cases, these aryl thioethers were successfully oxidized to the corresponding sulfoxides and sulfenic acid elimination afforded the corresponding vinylsilanes.     

Deep hydrodesulfurization of FCC gasoline and gas oil cuts: Comparison of CO effect,a by-product from biomass

Regarding the composition of the various feedstocks which should be hydrotreated in order to obtain fuels with amount of sulfur less than 10 wt ppm, we have shown that the presence of traces of CO, a by-product from lignocellulosic biomass feedstock conversion, inhibited the transformation of model compounds representative of FCC gasolines and gas oils over CoMo-based sulfide catalysts. Thus, this effect is more significant in the presence of 2-methylthiophene and 2,3-dimethylbut-2-ene representative of a FCC gasoline than in the presence of dibenzothiophene and 4,6-dimethyldibenzothiophene representative of a straight run gas oil, even if the operating conditions are not the same. This effect is attributed to phenomena of competitive adsorption between sulfur compounds, alkenes and CO on the catalyst surface.     

Synthesis of carbinoxamine via α-C(sp3)–H 2-pyridylation of O,S or N-containing compounds enabled by non-D–A-type super organoreductants and sulfoxide- or sulfide HAT reagents

The radical cations of tertiary amines (R₃N) have been well-established as the precursors of HAT reagents in photochemical transformations. Similarly, thiols and thioacids bearing SH groups have also been widely applied as HAT reagents. Despite the fact that sulfoxides (R₂SO) and sulfides (RSR) also bear lone pairs of electrons, these compounds have been barely reported as HAT reagents in photocatalysis. On the other hand, the α-C–H 4-pyridylation of O or N-containing compounds has been documented, whereas 2-pyridylation remains challenging. However, the antihistamine and anticholinergic agent carbinoxamine is an ether bearing 2-pyridyl, which has not been obtained by the existing α-photoarylation of ether. In this work, we report the discovery of a non-donor–acceptor (D–A) type organic photoreductant CBZ6 and sulfoxide/sulfide synergistically catalyzed general α-C(sp³)–H arylation of ethers, thioethers and amines. By using as low as 1 mol% of CBZ6 as a recyclable organic photoreductant and sulfoxides or sulfides as a new type of HAT reagent, the 2- or 4-pyridylation of O, N, or S-containing compounds has been accomplished. This is the first base-free version of α-C–H 2-/4-pyridylation of O, N, or S-containing compounds. It is the first example of sulfoxides or sulfides working as HAT reagents. It is also the first general method for photocatalytic HAT 2-pyridylation of various ethers, amines or thioethers.

We report the discovery of a non-donor–acceptor (D–A) type organic photoreductant CBZ6 and sulfoxide/sulfide synergistically catalyzed general α-C(sp³)–H arylation of ethers, thioethers and amines.     

Highly stereoselective additions of sulfur stabilized carbanions to [(S)R]-2-(p-tolylsulfinyl)cyclohexanones

We describe the addition reactions of α-thiocarbanions derived from sulfoxides, thioethers, and sulfones to 2-(p-tolylsulfinyl)cyclohexanones. The high stereoselectivity observed in the formation of the chiral hydroxylic carbon is controlled by the configuration of the sulfinyl group at the substrate, but it is modulated by the nature of the sulfur function at the reagent (SOTol>SO₂Ph>SPh). The highly stereoselective formation of the second stereogenic center generated in these reactions from prochiral anions is only achieved with sulfinylcarbanions, the configuration of which controls that of such a center.     

Interference of Transformer oil Matrices to the Internal Standards on PCB Quantification

Abstract

Polychlorinated biphenyls (PCBs) are toxic, perssstent, global environmental contaminants which were formulated as complex mixtures of congeners. Many methods have been developed in the past to analyze PCB in transformer oil samples for regulatory purposes. The most important consideration in the cleanup procedure is the ability to remove the oil from the sample matrix, since trace amount of oil will interfere with the subsequent GC-MS analysis. Electron capture detection (ECD) has been the most common method for gas chromatographic analysis of PCBs because of its high sensitivity toward halogenated compounds. ECD can also respond to some non-PCB compound resulting in biased concentrations of PCB. In this work, a two-stage cleanup method, using DMSO liquid/liquid extraction and HPLC column chromatography. has been applied to two types of transformer oil. Five internal standards have been selected to show their performance in the presence of different oil matrices. The comparison of the PCB quantification at different conditions for GC-MS and GC-ECD will be demonstrated.     

Role of Sulfur Compounds in Vegetable and Mushroom Aroma

At the base of the food pyramid is vegetables, which should be consumed most often of all food products, especially in raw and unprocessed form. Vegetables and mushrooms are rich sources of bioactive compounds that can fulfill various functions in plants, starting from protection against herbivores and being natural insecticides to pro-health functions in human nutrition. Many of these compounds contain sulfur in their structure. From the point of view of food producers, it is extremely important to know that some of them have flavor properties. Volatile sulfur compounds are often potent odorants, and in many vegetables, belonging mainly to Brassicaeae and Allium (Amaryllidaceae), sulfur compounds determine their specific flavor. Interestingly, some of the pathways that form volatile sulfur compounds in vegetables are also found in selected edible mushrooms. The most important odor-active organosulfur compounds can be divided into isothiocyanates, nitriles, epithionitriles, thiols, sulfides, and polysulfides, as well as others, such as sulfur containing carbonyl compounds and esters, R-L-cysteine sulfoxides, and finally heterocyclic sulfur compounds found in shiitake mushrooms or truffles. This review paper summarizes their precursors and biosynthesis, as well as their sensory properties and changes in selected technological processes.     

功能化酸性离子液体催化柴油氧化脱硫的研究

以功能化酸性离子液体为催化剂,30%双氧水为氧化剂,将加氢柴油中的含硫化合物氧化为相应的砜类物质,并用N-甲基吡咯烷酮（NMP）萃取一次。同时考察了反应温度、反应时间和催化剂用量等因素对氧化脱硫反应的影响,得出最佳反应条件为,3mL油样（硫的质量分数为200×10-6）、1.5g酸性离子液体、 0.3mL H2O2、 25℃,3.5h、VNMP/Vdiesel=1∶1,脱硫率可达到86.7%,柴油硫的质量分数仅为25×10-6左右,反应结束后,可通过简单的倾倒将油样和催化剂分离,重复使用5次,其催化活性变化不大。     

气相色谱法测定催化柴油中硫化物类型分布及数据对比

采用气相色谱-氢火焰离子化检测器-硫化学发光检测器（GC—FID—SCD）联用技术,建立了催化柴油中各种硫化物类型分布的分析方法。考察了色谱条件对催化柴油中各种硫化物分离的影响,定性了某催化柴油中的120多个硫化物,该方法还可以同时提供催化柴油中正构烷烃含量的分布信息。硫化物中的硫在1．5—700mg／L时其峰面积与质量浓度呈较好的线性关系,相关系数达0．9999,响应与硫化物的类型无关。催化柴油中苯并噻吩、4-甲基苯并噻吩、二苯并噻吩、4-甲基二苯并噻吩和4,6-二甲基二苯并噻吩等主要硫化物浓度测定的相对标准偏差（RSD）均小于5．0％。当信噪比（S／N）为3时,测得苯并噻吩硫的检出限为0．1mg／L。将该方法用于不同来源柴油中各种硫化物类型分布的研究,并与气相色谱一原子发射光谱检测器（GC—AED）测硫的数据进行了对比,两种检测器的定量结果大多数具有较好的相关性,相关系数大于0．95。     

Formation of diaryl sulfides and sulfoxides: Synthesis,characterization and structure activity correlation studies

Abstract

The synthesis of a series of stable diarylsulfides and sulfoxides is reported. All the newly synthesized compounds were characterized by ¹H, ¹³C NMR and mass spectroscopic techniques. A detailed mechanistic study indicates that the formation of sulfoxides follows the oxidation. In addition to synthesis, characterization and mechanistic studies, the glutathione peroxidase(GPx) mimetic activity of the newly synthesized compounds is described. It is observed that the diaryl sulfides having a heterocyclic ring attached to the nitrogen atom facilitates the oxidation of the sulfur center to form the corresponding sulfoxides. The substituents attached to the nitrogen atom play an important role in the catalytic activity of the substituted diaryl sulfides. The obtained data supports for the higher antioxidant activity of diaryl sulfides than that of the corresponding sulfoxides.     

气相色谱-质谱法测定变压器油正构烃含量

环烷基油是生产高性能变压器油的优质原料,以此为基础油生产的变压器油其凝点一般都小于-40℃,而变压器油在使用过程中对凝点(即低温流动性)有着非常高的要求,凝点的高低直接影响着油品的物理化学性能及电器性能。而油品的低温流动性与其组成中的正构烃(蜡)含量密切相关,据有关