Ferroelectric properties of Pr and Nb co-substituted Sr0.8Bi2.2Ta2O9 thin films

Thin film of both A- and B-site co-substituted Sr_0.8Bi_2.2Ta₂O₉ (SBT) by Pr³⁺ and Nb⁵⁺, i.e. Sr_0.8Pr_0.1Bi_2.1Ta_1.5Nb_0.5O₉ (SPBTN) was fabricated on Pt/Ti/SiO₂/Si substrates by metalorganic decomposition method. The Nb⁵⁺ substitution at B-site and Pr³⁺ substitution at A-site enhanced the remanent polarization and reduced the coercive field of the films, respectively. The remanent polarization (2P_r) value of the SPBTN film was 22 μC/cm². The coercive field (2E_c) value of the SPBTN film was 102 kV/cm, which was much lower than that of SBTN (165 kV/cm). The effects of substitution on structural and ferroelectric properties of SBT were discussed in detail. As a result, the A- and B-sites co-substitution may be one of the promising ways to improve ferroelectric properties of SBT.     

Influence of mobile space charges on electrical properties of ferroelectric Bi3.5La0.5Ti3O12 thin films

Lanthanum-substituted bismuth titanate, Bi_3.5La_0.5Ti₃O₁₂ (i.e., x=0.5 in Bi_4−xLa_xTi₃O₁₂), thin films have been grown on Pt/Ti/SiO₂/Si substrates using pulsed laser deposition. The frequency dependence of the real part ε′(ω) and the imaginary part ε″(ω) of the dielectric constant has been studied. The ε′(ω) does not show any sudden change within the frequency range of 10²-10⁶ Hz. In contrast, the ε″(ω) shows a large dispersion as frequency decreases. The observed relaxation behavior in ε″(ω) can be explained in terms of a migration of oxygen vacancies in (Bi₂O₂)²⁺ layers, not in Bi₂Ti₃O₁₀ perovskite layers.     

La掺杂对Bi4Ti3O12薄膜铁电性能的影响

利用Sol-Gel法在Pt/Ti/SiO₂/Si衬底上制备出Bi₄Ti₃O₁₂和Bi_3.25La_0.75Ti₃O₁₂薄膜，研究了La掺杂对Bi₄Ti₃O₁₂薄膜的晶体结构、铁电性能和疲劳特性的影响，发现La掺杂没有改变Bi₄Ti₃O₁₂薄膜的基本晶体结构，并且提高了Bi₄Ti₃O₁₂铁电薄膜的剩余极化值和抗疲劳性能，对La掺杂改善Bi₄Ti₃O₁₂铁电薄膜性能的机理进行了讨论. 关键词： 铁电性能 4Ti₃O₁₂薄膜')" href="#">Bi₄Ti₃O₁₂薄膜 3.25La_0.75Ti₃O₁₂薄膜')" href="#">Bi_3.25La_0.75Ti₃O₁₂薄膜 sol-gel法 La掺杂     

Ferroelectric properties of Bi3.25−x/3La0.75Ti3−xNbxO12 films prepared by pulsed laser deposition

Bi₄Ti₃O₁₂ (BiT), Bi_3.25La_0.75Ti₃O₁₂ (BLT), Bi_4−x/3Ti_3−xNb_xO₁₂ (BTN) and Bi_3.25−x/3La_0.75Ti_3−xNb_xO₁₂ (BLTN) thin films have been prepared by pulsed laser deposition. BTN and BLTN films exhibit a maximum in the remanent polarization P_r at a Nb content x=0.018. At this Nb content, the BLTN film has a P_r value (25 μC/cm²) that is much higher than that of BiT and a coercive field similar to that of BiT. The polarization of this BLTN film is fatigue-free up to 10⁹ switching cycles. The high fatigue resistance is mainly due to the substitution of Bi³⁺ ions by La³⁺ ions at the A site and the enhanced P_r arises largely from the replacement of Ti⁴⁺ ions by Nb⁵⁺ ions at the B site. The mechanisms behind the effects of the substitution at the two sites are discussed.     

Ferroelectric properties of Pr6O11-doped Bi4Ti3O12

Praseodymium doped Bi₄Ti₃O₁₂ (BIT) ceramics with composition Bi_2.9Pr_0.9Ti₃O₁₂ (BPT) were prepared by solid state reaction. These samples have polycrystalline Bi-layered perovskite structure without preferred orientation, and consist of well-developed plate-like grains with random orientation. Pr doping into BIT causes a large shift of the Curie temperature (T_C) of the BIT from 675 to 398 °C. At an electric field of 87 kV/cm, the remanent polarization and the coercive field of the BPT ceramics are 30 μC/cm² and 52 kV/cm, respectively. Furthermore, the dielectric permittivity and the dissipation factor of the BPT ceramics are 300 and 0.003 at 1 MHz, 1 V, and room temperature. Ferroelectric properties of the BPT ceramics are superior to V-doped Bi₄Ti₃O₁₂ (∼20 μC/cm² and 80 kV/cm) and (Sr, Ta)-doped Bi₄Ti₃O₁₂ (∼12 μC/cm² and 71 kV/cm) ceramics. In addition, the dense ceramics of praseodymium-doped B₄Ti₃O₁₂ were obtained by sintering at 1100 °C, about 100-200 °C lower than those of the SrBi₂Ta₂O₉ system.     

Impact of annealing atmosphere on the multiferroic and dielectric properties of BiFeO3/Bi3.25La0.75Ti3O12 thin films

Multiferroic BiFeO₃/Bi_3.25La_0.75Ti₃O₁₂ films annealed in different atmospheres (N₂ or O₂) were prepared on Pt/Ti/SiO₂/Si substrates via a metal organic decomposition method. Based on our experimental results, it is considered that, in the films annealed in N₂, fewer Fe²⁺ ions while more oxygen vacancies are involved. As a result, at room temperature, predominated by the reduced Fe²⁺ fraction, lower leakage current and dielectric loss, better ferroelectric property while reduced magnetization are observed. However, the oxygen vacancies might be thermally activated at elevated temperature; thus, more strongly temperature-dependent leakage current and a higher dielectric relaxation peak are observed for the films annealed in N₂.     

Si基Bi3.25La0.75Ti3O12铁电薄膜的制备与特性研究

采用Sol-Gel工艺低温制备了Si基Bi_3.25La_0.75Ti₃O₁₂铁电薄膜.研究了退火温度对薄膜微观结构、介电特性与铁电性能的影响.500℃退火处理的Bi_3.25La_0.75Ti₃O₁₂薄膜未能充分晶化，晶粒细小且有非晶团聚，介电与铁电性能均较差.高于550℃退火处理的Bi_3.25La_{0.75 关键词： 铁电薄膜 3.25}La_0.75Ti₃O₁₂')" href="#">Bi_3.25La_0.75Ti₃O₁₂ Sol-Gel工艺     

Microstructures and multiferroic properties of textured Bi0.8La0.2FeO3 thin films

La-substituted BiFeO₃, Bi_0.8La_0.2FeO₃, thin films were fabricated on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and high-resolution transmission electron microscope were used to analyze the structures of the films. The results show the films fabricated under optimized growth condition are (0 1 2) textured. X-ray photoemission spectroscopy results indicate that the oxidation state of Fe ion is Fe³⁺ in the films without detectable Fe²⁺. The films show low leakage current and excellent dielectric characters. Multiferroic properties with a remnant ferroelectric polarization of 5.2 μC/cm² and a remanent magnetization of 0.02 μ_B/Fe were established. These results have some implications for further research.     

Preparation and multi-properties of insulated single-phase BiFeO3 ceramics

Six types of BiFeO₃ ceramic samples, with subtle differences in synthesis conditions, were prepared. The comparison of their phases, electrical resistivity, and porosity revealed that the use of Bi₂O₃ and Fe₂O₃ powders of <1 μm size and a rapid liquid-phase sintering process of 855 °C for 5 min at 100 °C/s is beneficial to synthesize poreless single-phase BiFeO₃ samples with high electrical resistivity of ∼5×10¹² Ω cm. Deoxygenated Bi_xFe_yO_{1.5x+1.5y−δ} (x≠y, δ≥0) impurities were identified and found to be the main cause of low electrical resistivity and high porosity in the multi-phase samples. Large saturation polarization of 16.6 μC/cm² and low leakage current density of 30 mA/m², both at a high electric field of 145 kV/cm, were measured in the optimized single-phase samples at room temperature besides a large piezoelectric d₃₃ coefficient of 27 pC/N and an obvious canted antiferromagnetic behavior.     

Multiferroic properties of solben gel derived Bi5Fe1-xCoxTi3O15 thin films

Co-doped Bi₅FeTi₃O₁₅ thin films (BFCT-x, Bi₅Fe_1-xCo_xTi₃O₁₅) were prepared using a sol—gel technique. XRD patterns confirm their single phase Aurivillius structure, and the corresponding powder Rietveld analysis indicates the change of space group around x=0.12. The magnetic hysteresis loops are obtained and ferromagnetism is therefore confirmed in BFCT-x thin films. The remanent magnetization (M_r) first increases and reaches the maximum value of 0.42 emu/cm³ at x=0.12 due to the possible Fe³⁺—O—Co³⁺ ferromagnetic coupling. When x = 0.25, the M_r increases again because of the dominant Fe³⁺—O—Co³⁺ ferromagnetic coupling. The remanent polarization (2P_r) of BFCT-0.25 was measured to be as high as 62 μC/cm², a 75% increase when compared with the non-doped BFCT-0 films. The 2P_r remains almost unchanged after being subjected to 5.2 × 10⁹ read/write cycles. Greatly enhanced ferroelectric properties are considered to be associated with decreased leakage current density.     

Combinatorial exploration of flux material for Bi4Ti3O12 single crystal film growth

The combinatorial approach to materials synthesis was employed for the quick screening of a flux material for liquid phase-mediated epitaxy of Bi₄Ti₃O₁₂ single crystal film. A series of ternary flux libraries composed of two self-fluxes (Bi₂O₃ and Bi₄Ti₃O₁₂) and an impurity flux (VO_x, WO_x, CuO_x, BiPO_x, BaO, MoO_x) were fabricated on the SrTiO₃ (0 0 1) substrates. Then, stoichiometric Bi₄Ti₃O₁₂ was grown on each one of these flux libraries at a temperature presumed to melt the flux. High-throughput characterization with the concurrent X-ray diffraction (XRD) method resulted in the discovery of a novel flux material, CuO, containing Bi₂O₃, for Bi₄Ti₃O₁₂ single crystal film.     

Compositional dependence of ferroelectric properties of highly c-axis oriented Bi4−xNdxTi3O12 film capacitors

Highly c-axis oriented neodymium-modified bismuth titanate (Bi_4−xNd_xTi₃O₁₂) films having a variety of neodymium (Nd) contents were successfully grown on Pt/TiO₂/SiO₂/Si(100) substrates using metal-organic sol decomposition. After systematically examining ferroelectric properties of the c-axis oriented Bi_4−xNd_xTi₃O₁₂ film capacitors as a function of the Nd-content, we concluded that the capacitor with x=0.85 had the largest remanent polarization. The Bi_3.15Nd_0.85Ti₃O₁₂ capacitor fabricated using a top Pt electrode showed well-saturated polarization-electric field (P-E) switching curves with the remanent polarization (P_r) of 51 μC/cm² and the coercive field (E_c) of 99 kV/cm at an applied voltage of 10 V. More importantly, the Pt/Bi_3.15Nd_0.85Ti₃O₁₂/Pt capacitor exhibited fatigue-free behavior up to 4.5×10¹⁰ read/write switching cycles at a frequency of 1 MHz. The capacitor also demonstrated an excellent charge-retaining ability and a strong resistance against the imprinting failure.     

Dependence of excess bismuth content in precursor sols on ferroelectric and dielectric properties of Bi3.25La0.75Ti3O12 thin films fabricated by chemical solution deposition

Bi_3.25La_0.75Ti₃O₁₂ (BLT) thin films were fabricated on Pt/Ti/SiO₂/Si(1 0 0) substrates by chemical solution deposition (CSD), and the dependence of ferroelectric and dielectric properties of the as-deposited BLT thin films on excess Bi content in precursor sols was studied. It is found that the prepared BLT thin film shows the best polarization-electric field, capacitance-voltage and dielectric constant (?_r)-frequency characteristics, when the value of excess Bi content in precursor sols is 10%. In detail, its remnant polarization (2P_r) value is 40 μC/cm², the capacitance tunability is 21% measured at room temperature under conditions of an applied voltage of 8 V and measurement frequency of 10 kHz, and the ?_r is 696 at 100 kHz frequency.     

Electrical behavior of BaZr0.1Ti0.9O3 and BaZr0.2Ti0.8O3 thin films

BaZr_0.1Ti_0.9O₃ and BaZr_0.2Ti_0.8O₃ (BZT) thin films were deposited on Pt/Ti/LaAlO₃ (1 0 0) substrates by radio-frequency magnetron sputtering, respectively. The films were further annealed at 800 °C for 30 min in oxygen. X-ray diffraction θ-2θ and Φ-scans showed that BaZr_0.1Ti_0.9O₃ films displayed a highly (h 0 0) preferred orientation and a good cube-on-cube epitaxial growth on the LaAlO₃ (1 0 0) substrate, while there are no obvious preferential orientation in BaZr_0.2Ti_0.8O₃ thin films. The BaZr_0.1Ti_0.9O₃ films possess larger grain size, higher dielectric constant, larger tunability, larger remanent polarization and coercive electric field than that of BaZr_0.2Ti_0.8O₃ films. Whereas, BaZr_0.1Ti_0.9O₃ films have larger dielectric losses and leakage current density. The results suggest that Zr⁴⁺ ion can decrease dielectric constant and restrain non-linearity. Moreover, the enhancement in dielectric properties of BaZr_0.1Ti_0.9O₃ films may be attributed to (1 0 0) preferred orientation.     

Synthesis and laser patterning of Bi-doped Y3Fe5O12 crystals in germanosilicate glasses

New germanosilicate glasses giving the crystallization of yttrium iron garnet Y₃Fe₅O₁₂ (YIG) and Bi-doped YIG, 23Na₂O-xBi₂O₃-(12−x)Y₂O₃-25Fe₂O₃-20SiO₂-20GeO₂ (mol%), are developed, and the laser-induced crystallization technique is applied to the glasses to pattern YIG and Bi-doped YIG crystals on the glass surface. It is clarified from the Mössbauer effect measurements that iron ions in the glasses are present mainly as Fe³⁺. It is suggested from the X-ray diffraction analyses and magnetization measurements that Si⁴⁺ ions are incorporated into YIG crystals formed in the crystallization of glasses. The irradiations (laser power: 32-60 mW and laser scanning speed: 7 μm/s) of continuous wave Yb:YVO₄ fiber laser (wavelength: 1080 nm) are found to induce YIG and Bi-doped YIG crystals, indicating that Fe³⁺ ions in the glasses act as suitable transition metal ions for the laser-induced crystallization. It is suggested that YIG and Bi-doped YIG crystals in the laser irradiated part might orient. The present study will be a first step for the patterning of magnetic crystals containing iron ions in glasses.     

Composition depth profiles of Bi3.15Nd0.85Ti3O12 thin films studied by X-ray photoelectron spectroscopy

In the present work, X-ray photoelectron spectroscopy (XPS) was used to investigate the composition depth profiles of Bi_3.15Nd_0.85Ti₃O₁₂ (BNT) ferroelectric thin film, which was prepared on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by chemical solution deposition (CSD). It is shown that there are three distinct regions formed in BNT film, which are surface layer, bulk film and interface layer. The surface of film is found to consist of one outermost Bi-rich region. High resolution spectra of the O 1s peak in the surface can be decomposed into two components of metallic oxide oxygen and surface adsorbed oxygen. The distribution of component elements is nearly uniform within the bulk film. In the bulk film, high resolution XPS spectra of O 1s, Bi 4f, Nd 3d, Ti 2p are in agreement with the element chemical states of the BNT system. The interfacial layer is formed through the interdiffusion between the BNT film and Pt electrode. In addition, the Ar⁺-ion sputtering changes lots of Bi³⁺ ions into Bi⁰ due to weak Bi-O bond and high etching energy.     

Electrical properties of neodymium doped CaBi4Ti4O15 ceramics

Neodymium doped bismuth layer structure ferroelectrics (BLSFs) ceramics CaBi_4−xNd_xTi₄O₁₅ (x=0, 0.25, 0.50, 0.75) were prepared by solid-state reaction method. X-ray diffraction pattern showed that single phase was formed when x=0-0.75. The refined lattice parameters showed that a (b) axes decrease at x=0.25 and increase with more Nd³⁺ dopant. The effects of Nd³⁺ doping on the dielectric and ferroelectric properties of CaBi₄Ti₄O₁₅ ceramics are studied. Nd³⁺ dopant decreased the Curie temperature linearly, and the dielectric loss, tan δ, as well. The remnant polarization of Nd³⁺ doped CaBi₄Ti₄O₁₅ ceramics was increased by 80% at x=0.25, while more Nd³⁺ dopant decreased the remnant polarization. CaBi_3.75Nd_0.25Ti₄O₁₅ ceramics had the largest piezoelectric constant d₃₃. The structure and properties of CaBi_4−xNd_xTi₄O₁₅ ceramics showed that Nd³⁺ may occupy different crystal locations when Nd³⁺ content x is less than 0.25 and more than 0.50.     

Ferroelectric properties of highly c-axis oriented Bi4−xLaxTi3O12 film-based capacitors

Highly c-axis oriented lanthanum-modified bismuth titanate (Bi_4−xLa_xTi₃O₁₂) films having a variety of lanthanum (La) contents were grown on Pt/TiO₂/SiO₂/Si(100) substrates using metal-organic sol deposition and subsequent annealing at 650 °C for 1 h. After systematically examining the ferroelectric properties of Bi_4−xLa_xTi₃O₁₂ films as a function of the La-content, it was concluded that the film with x=0.85 had the largest remanent polarization in the direction parallel to the c-axis. The Pt/Bi_3.15La_0.85Ti₃O₁₂/Pt capacitor showed a well-saturated polarization-electric field (P-E) switching curve with the switching remanent polarization (2P_r) value of 33 μC/cm² and the coercive field (E_c) of 68 kV/cm at an applied voltage of 10 V. More importantly, the capacitor exhibited fatigue-free behavior up to 6.5×10¹⁰ read/write switching cycles at a frequency of 1 MHz. The capacitor also demonstrated an excellent charge-retaining ability and a strong resistance against the imprinting failure.     

Synthesis and ferroelectric properties of bismuth layer-structured (Bi7−xSrx)(Fe3−xTi3+x)O21 solid solutions

Bismuth layer-structured (Bi_7−xSr_x)(Fe_3−xTi_3+x)O₂₁ (BSFT) ceramics were synthesized and the ferroelectric properties and crystal structure were investigated. X-ray powder diffraction profiles and refinement of the lattice parameters indicated single phase BSFT was obtained in the composition range 0-1.5. The lattice parameter b of BSFT remained almost constant, while a slight decrease in the lattice parameter a was observed by the Sr and Ti substitution for Bi and Fe, respectively, which indicated an increase in the orthorhombicity. The dependence of the BSFT lattice parameter on temperature implied a phase transition from the orthorhombic to the tetragonal phase, which was in good agreement with the Curie temperature. The remnant polarization P_r, of BSFT was significantly improved by the Sr and Ti substitution for Bi and Fe, and ranged from 9 to 16 μC/cm², although no remarkable variation in the coercive field E_c was observed. As a result, a well-saturated P-E hysteresis loop of BSFT ceramic was obtained at x=0.5 with a P_r of 30 μC/cm at an applied voltage of 280 kV/cm.     

Multiferroic properties of Bi0.8La0.2FeO3/CoFe2O4 multilayer thin films

Bi_0.8La_0.2FeO₃/CoFe₂O₄ (BLFO/CFO) multilayer thin films (totally 20 layers BLFO and 19 layers CFO) were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and transmission electron microscope measurements show that the films are polycrystalline and consisted of multilayered structure. Ferroelectric hysteresis loops with remnant polarization and saturated polarization of 4.2 and 13.3 μC/cm², respectively, were observed. On the other hand, the films show well-shaped magnetization hysteresis loops with saturated and remnant magnetization of 34.7 and 11.4 emu/cm³, respectively, which are significantly larger than pure BLFO thin films deposited under the same conditions. These results indicate that constructing epitaxial superlattice might be a promising way to fabricate multiferroics with improved properties.