Electrocatalytic activity of poly(3-methylthiophene) electrodes

Poly 3-methylthiophene (P3MT) modified electrodes have shown an improvement for detecting catecholamines when compared to classical ones. Past work with this polymer electrode suggested the possible presence of “active sites,” which are believed to be the polymer’s center of electrocatalytic activity. The interaction of 1,5-anthroquinone-disolfonic acid (1,5-AQDS) at the P3MT electrode showed a nonreversible behavior resulting in the blocking of “the active sites,” suggesting the specific electcatalytical activity of this polymer is limited to catechol and similar compounds. In order to improve catecholamine detection, two methods of electropolymerization for P3MT were compared under similar conditions; (1) a constant potential for a specific length of time, and (2) potential cycling. It was found that cycling provided a more sensitive CV, i.e. increased number of active sites. Under a controlled pH study (pH range 2–9), the polymer electrode maintained its superior performance, manifested as lower ΔE and higher i, toward catechol over the traditional electrodes. Two different supporting electrolytes were used, sulfate and phosphate, and it was found that in neutral or basic solutions containing phosphate, the oxidation and reduction potentials of catechol shifted to lower values. Solutions containing sulfate exhibited no shift in the oxidation potential at any pH value.     

肾上腺素在聚对氨基吡啶化学修饰电极上的电化学行为及其吸附伏安法测定

报道了肾上腺素(EP)在聚对氨基吡啶(POAP)修饰电极上的电化学行为及其测定方法。POAP修饰电极对EP的氧化有良好的电催化作用。最佳条件下,氧化峰电流与EP的浓度在5×10-8～9×10-6mol L和9×10-6～9×10-5mol L范围内呈良好线性关系,相关系数分别为0.9990和0.9997,检出限为2.5×10-9mol L。该电极寿命已超过两年,已用于实际样品中EP的测定。     

Electrochemical determination of iodide by poly(3-aminophenylboronic acid) film electrode at moderately low pH ranges

A new potentiometric sensor for the determination of iodide based on poly(3-aminophenylboronic acid) (PAPBA) film electrode was constructed. Poly(3-Aminophenylboronic acid) films were synthesized electrochemically on platinum electrode by cyclic voltammetry. The effect of film thickness, pH, and preconditioning parameters on the electrode performance were examined. The analytical performance was evaluated and linear calibration graphs were obtained in the concentration range of 10⁻⁶ to 10⁻¹ M iodide ion. The limit of detection was found to be 8 × 10⁻⁷ M. The response time of the sensor was 5 s and its lifetime is about one week. To check the selectivity of the PAPBA film for iodide ion, potential interferences such as Cl⁻, Br⁻, F⁻, CN⁻, IO₃⁻, Ca²⁺, and Mg²⁺ were tested. The PAPBA electrode was also employed as a sensing platform for the determination of iodide ions in commercial table salt.     

铂微粒/聚3-甲基噻吩修饰电极测定对苯二酚

采用电化学聚合和电化学沉积法制备了负载铂微粒的聚3-甲基噻吩(P3MT)修饰玻碳电极(Pt/P3MT/GCE)。通过循环伏安法研究了对苯二酚在该电极上的电化学行为,并优化了实验参数,在此基础上建立了一种用微分脉冲伏安法直接测定对苯二酚的方法。在酸性溶液中,对苯二酚的氧化峰电流与其浓度在1.0×10-5~8.0×10-3mol·L-1的范围内呈良好的线性关系(r=0.9992),检测限为1.0×10-6mol·L-1,水样中对苯二酚的加标回收率在98%~104%之间。     

Reactions of solute species at an electrode modified with titanocene functionalized polypyrrole film: ferrocene and titanocene dichloride

We have studied for the first time the ability of a conducting polymer film, p(Tc3Py), representing a polypyrrole matrix with covalently attached titanocene dichloride (TcCl₂) centers, to serve as an intermediator for the electron charge transport between the electrode and the reaction sites of solute reactants. The standard potential of the first of these electroactive species, ferrocene (Fc), is in the range where the polymer matrix is in its slightly oxidized state so that solute Fc species give a reversible response at the surface of this modified electrode. Another solute reactant, TcCl₂, was studied in solutions in which it demonstrates a (quasi)reversible behavior at bare electrode surfaces, THF+TBAPF₆ and AN+TEACl. The standard redox potential of this species belongs to the range of the electroactivity of immobilized TcCl₂ centers (where the matrix is in its non-conducting state) so that the electron charge has to be transported via stepwise redox reactions between neighboring centers inside the film. The combination, solute reactant+film, results in a greater CV current compared to the response of the film in background solution or of the solute species at the bare electrode surface. This current for THF solution even exceeds the sum of separate currents for the film and the reactant. This finding is attributed to a catalytic effect of solute species as redox intermediators for the transformation of immobilized electroactive centers leading to a greater degree of the film reduction. The presence of solute TcCl₂ species results in a much greater stability of immobilized centers (compared to the corresponding reactant-free solution), both in the course of CV with the passage of the range of their response and in experiments with the film holding at the potential within this range. This holding leads to an almost constant current related to the reaction of solute species at the film/solution interface. Our estimate shows that immobilized centers undergo above 10,000 reversible transformations (without an observed tendency to the degradation) to ensure the passage of this current. The conclusion has been drawn that immobilized TcCl₂ centers are able to serve as sufficiently stable redox intermediators for the electron charge transport across the film, a prerequisite for the catalytic applications of such films.Abbreviations AN acetonitrile - THF tetrahydrofuran - Cp cyclopentadienyl, C₅H₅ - Cp cyclopentadienyl radical, C₅H₄ - Fc ferrocene, Cp₂Fe - TcCl₂ titanocene=bis(cyclopentadienyl)titanium dichloride, Cp₂TiCl₂ or its radical CpCpTiCl₂ - PPy polypyrrole - Tc3Py titanocene-propyl-pyrrole, Cl₂TiCpCp(CH₂)₃NC₄H₄ - p(Tc3Py) polymer obtained from Tc3Py - TBAPF₆ tetrabuthylammonium hexafluorophosphate - TEACl tetraethylammonium chlorideDedicated to Zbigniew Galus on the occasion of his 70th birthday.     

聚1,8-萘二胺修饰玻碳电极测定痕量汞

采用电化学聚合的方法制备了聚1,8-萘二胺修饰玻碳电极,建立了吸附富集-阳极溶出伏安法测定痕量Hg2+的新方法.优化了各种实验参数(如富集底液的pH,富集时间等),并考察了其它离子的干扰.在最佳实验条件下,Hg2+在0.001～0.1 mg/L及0.1～5.0 mg/L质量浓度范围内均与溶出峰电流成良好的线性关系,检出限为0.0005 mg/L.该法可用于实际工业废水中汞的测定.     

Voltammetric determination of isoprenaline in pharmaceutical preparations using a copper(II) hexacyanoferrate(III) modified carbon paste electrode

The electroanalytical determination of isoprenaline in pharmaceutical preparations of a homemade carbon paste electrode modified with copper(II) hexacyanoferrate(III) (CuHCF) was studied by cyclic voltammetry. Several parameters were studied for the optimization of the sensor such as electrode composition, electrolytic solution, pH effect, potential scan rate and interferences in potential. The optimum conditions were found in an electrode composition (in mass) of 15% CuHCF, 60% graphite and 25% mineral oil in 0.5 mol l⁻¹ acetate buffer solution at pH 6.0. The analytical curve for isoprenaline was linear in the concentration range from 1.96×10⁻⁴ to 1.07×10⁻³ mol l⁻¹ with a detection limit of 8.0×10⁻⁵ mol l⁻¹. The relative standard deviation was 1.2% for 1.96×10⁻⁴ mol l⁻¹ isoprenaline solution (n=5). The procedure was successfully applied to the determination of isoprenaline in pharmaceutical preparations; the CuHCF modified carbon paste electrode gave comparable results to those results obtained using a UV spectrophotometric method.     

Voltammetric determination of N-acetylcysteine using a carbon paste electrode modified with copper(II) hexacyanoferrate(III)

The preparation and electrochemical characterization of a carbon paste electrode modified with copper(II) hexacyanoferrate(III) (CuHCF) as well as its behavior as electrocatalyst toward the oxidation of N-acetylcysteine were investigated. The electrochemical behavior of the modified electrode and the electrooxidation of N-acetylcysteine were explored using sweep linear voltammetry. The best voltammetric response was observed for a paste composition of 20% (w/w) copper(II) hexacyanoferrate(III) complex, acetate buffer solution at pH of 6.0 as the electrolyte and scan rate of 10 mV s^− 1. A linear voltammetric response for N-acetylcysteine was obtained in the concentration range from 1.2 × 10^− 4 to 8.3 × 10^− 4 mol L^− 1, with a detection limit of 6.3 × 10^− 5 mol L^− 1. The proposed electrode is useful for the quality control and routine analysis of N-acetylcysteine in pharmaceutical formulations.     

New triiodomercurate-modified carbon paste electrode for the potentiometric determination of mercury

A new tetrazolium-triiodomercurate-modified carbon paste electrode has been described for the sensitive and selective determination of mercury. The electrode shows a stable, near-Nernstian response for 1×10⁻³ to 6×10⁻⁶ M [HgI₃]⁻ at 25 °C over the pH range of 4.0-9.0, with an anionic slope of 55.5±0.4 mV. The lower detection limit is 4×10⁻⁶ M with a fast response time of 30-50 s. Selectivity coefficients of a number of interfering anions and iodo complexes of some metal ions have been estimated. The interference from many of the investigated ions is negligible. The determination of 1-200 μg/ml of mercury in aqueous solutions shows an average recovery of 98.5% and a mean relative standard deviation of 1.6% at 50.0 μg/ml. The direct determination of mercury in spiked wastewater, metal amalgams and dental alloy gave results that compare favorably with those obtained by the cold vapor atomic absorption spectrometric method. Potentiometric titration of mercury and phenylmercury acetate with standard potassium iodide has been monitored using the developed triiodomercurate-carbon paste electrode (CPE) as an end point indicator electrode.     

Voltammetric determination of 4-nitrophenol at a lithium tetracyanoethylenide (LiTCNE) modified glassy carbon electrode

The reduction of 4-nitrophenol (4-NP) has been carried out on a modified glassy carbon electrode using cyclic and differential pulse voltammetry (DPV). The sensor was prepared by modifying the electrode with lithium tetracyanoethylenide (LiTCNE) and poly-l-lysine (PLL) film. With this modified electrode 4-NP was reduced at −0.7 V versus SCE. The sensor presented better performance in 0.1 mol l⁻¹ acetate buffer at pH 4.0. The other experimental parameters, such as concentration of LiTCNE and PLL, pulse amplitude and scan rate were optimized. Under optimized operational conditions, a linear response range from 27 up to 23200 nmol l⁻¹ was obtained with a sensitivity of 3.057 nA l nmol⁻¹ cm⁻². The detection limit for 4-NP determination was 7.5 nmol l⁻¹. The proposed sensor presented good repeatability, evaluated in term of relative standard deviation (R.S.D.=4.4%) for n=10 and was applied for 4-NP determination in water samples. The average recovery for these samples was 103.0 (± 0.7)%.     

Construction of a carbon nanocomposite electrode based on amino acids functionalized gold nanoparticles for trace electrochemical detection of mercury

A simple, highly sensitive and selective carbon nanocomposite electrode has been developed for the electrochemical trace determination of mercury. This mercury nanocomposite sensor was designed by incorporation of thiolated amino acids capped AuNps into the carbon ionic liquid electrode (CILE) which provides remarkably improved sensitivity and selectivity for the electrochemical stripping assay of Hg(II). Mercury ions are expected to interact with amino acids through cooperative metal–ligand interaction to form a stable complex which provides a sensitive approach for electrochemical detection of Hg(II) in the presence of other metal ions. The detection limit was found to be 2.3 nM (S/N = 3) that is lower than the permitted value of Hg(II) reported by the Environmental Protection Agency (EPA) limit of Hg(II) for drinkable water. The proposed nanocomposite electrode exhibits good applicability for monitoring Hg(II) in tap and waste water.     

Voltammetric determination of mesotrione at hanging mercury drop electrode

A study of the electrochemical reduction of the mesotrione pesticide on a hanging mercury drop electrode (HMDE) was performed as a basis for the development of a sensitive analytical method for natural samples. The electrochemical characteristics of herbicide mesotrione dissolved in a phosphate buffer (pH 7.0) have been determined by means of electrochemical techniques such as cyclic voltammetry (CV) and differential pulse voltammetry (DPV) over a wide range of pH from 2.0 to 10.0. The experimental parameters, such as electrolyte type and its pH, pulse amplitude, and scan rate were optimized. The method was applied to the determination of the pesticide in a spiked soil samples. Using this method, a linear calibration curve for mesotrione was obtained up to the 0.1 μM range in pH 7 phosphate buffer solution with a detection limit (S/N = 3) of 50 nM. The method can be applied successfully to the determination of mesotrione in soils. The text was submitted by the authors in English.     

碳纳米管-TiO_2修饰电极伏安法测定维生素K_3

利用碳纳米管、二氧化钛两种纳米材料制成碳纳米管-TiO2复合膜修饰电极,进行了维生素K3电化学行为的研究。维生素K3在碳纳米管-TiO2复合膜修饰电极的电化学响应优于碳纳米管修饰电极,表明前者具有更好的催化作用。通过条件实验的优化,结果表明维生素K3在pH=9.42的氨水-NH4Cl底液中,富集时间为10s,富集电位于-0.60V,扫描速度为0.1V/s时有稳定的灵敏的氧化还原峰。峰电流与维生素K3浓度在3.0×10-6～8.0×10-5mol/L范围内呈良好的线性关系,检出限为5.0×10-7 mol/L。考查了修饰电极的重现性,5次平行测量的RSD为1.78%。该方法用于片剂药品中维生素K3含量的测定,回收率在97.5%～102%之间。     

A novel chemically modified carbon paste electrode based on a new mercury(II) complex for selective potentiometric determination of bromide ion

A new modified carbon paste electrode based on a recently synthesized mercury (II) complex of a pyridine containing proton transfer compound as a suitable carrier for Br⁻ ion is described. The electrode has a linear dynamic range between 3.00×10⁻² and 1.0×10⁻⁵ M with a near-Nernastian slope of 61.0±0.9 mV per decade and a detection limit of 4.0×10⁻⁶ M (0.32 ppm). The potentiometric response is independent of the pH of the solution in the pH range 4.0–8.3. The electrode possesses the advantages of low resistance, fast response and good over a variety of other anions. It was applied as an indicator electrode in potentiometric titration of bromide ions and for the recovery of Br⁻ from tap water.     

Voltammetric Determination of Mercury(II) at Poly(3‐hexylthiophene) Film Electrode. Effect of Halide Ions

The well‐known method for the determination of mercury(II), which is based on the anodic stripping voltammetry of mercury(II), has been adapted for applications at the thin film poly(3‐hexylthiophene) polymer electrode. Halide ions have been found to increase the sensitivity of the mercury response and shift it more positive potentials. This behavior is explained by formation of mercuric halide which can be easily deposited and stripped from the polymer electrode surface. The procedure was optimized for mercury determination. For 120 s accumulation time, detection limit of 5 ng mL^?1 mercury(II) has been observed. The relative standard deviation is 1.3% at 40 ng mL^?1 mercury(II). The performance of the polymer film studied in this work was evaluated in the presence of surfactants and some potential interfering metal ions such as cadmium, lead, copper and nickel.     

Voltammetric determination of trace amounts of mercury with a carbon paste electrode modified with an anion-exchanger

Summary A carbon paste electrode modified with a liquid anion exchanger (Amberlite LA2) was used for the voltammetric determination of mercury(II). Mercury is preconcentrated, as tetrachloromercurate(II), onto the surface of the modified electrode only by the ion-exchange effect of the modifier without application of potential. After exchange of the medium the accumulated amount of mercury(II) is determined by differential pulse anodic stripping voltammetry in a blank electrolyte solution. The response depends on the concentration of mercury in the bulk solution, preconcentration time, and other parameters. The detection limit was 1 g Hg(II)/l when a suitable time for preconcentration was chosen. Preconcentration for 5 min yields a linear calibration graph for concentrations up to 1000 g Hg(II)/l. The effect of other ions on the determination of mercury and the applicability of the method to the analysis of phenylmercury compounds in pharmaceutical preparations were investigated.     

Ultra trace level square wave anodic stripping voltammetric sensing of mercury(II) ions in environmental samples using a Schiff base-modified carbon paste electrode

ABSTRACT

In this approach, a new carbon paste electrode modified with N,N′-bis(5-bromo-2-hydroxybenzylidene)-2,2-dimethylpropane-1,3-diamine Schiff base ligand (L) was synthesised for selective and effective determination of Hg²⁺ ions in aqueous environmental samples using cyclic and square wave anodic stripping voltammetric methods. First, the selective detection of mercury ion was confirmed by evaluating the stability constants of metal complexes formed between the Schiff base ligand (L) and some desired cations by conductometric measurements. Afterwards, by preparing an effective carbon paste electrode modified with L, the experimental and instrumental parameters affecting the performance of modified electrode were investigated. Square wave anodic stripping voltammograms were obtained after applying an accumulation potential ?0.5 V and accumulation time 150 s in Britton–Robinson buffer solution at pH 2.0. The optimal square wave parameters found are pulse amplitude 75 mV, frequency 50 Hz and step potential 6 mV. The procedure exhibited linear range from 0.4 to 120 μg L^?1 Hg²⁺ with a limit of detection of 0.042 μg L^?1. The proposed electrode was proved to be highly selective in the presence of various cations and anions and was successfully used for determination of mercury in tobacco and several water samples.     

聚磺胺嘧啶修饰电极伏安法测定对乙酰氨基酚

利用循环伏安法制备了聚磺胺嘧啶修饰电极, 研究了对乙酰氨基酚在该修饰电极上的电化学行为. 该电极对对乙酰氨基酚有较强的电催化作用. 在pH 9.0的PBS缓冲溶液中, 用循环伏安法和差分脉冲伏安法在该电极上测定了对乙酰氨基酚, 其线性范围分别为4.0×10-6～3.0×10-4 mol/L和2.0×10-7～1.0×10-5 mol/L, 检出限分别为9.0×10-7 mol/L和8.0×10-8 mol/L.     

Stripping voltammetric determination of trace amounts of mercury using a carbon paste electrode modified with 2-mercapto-4(3H)-quinazolinone

A carbon paste electrode modified with 2-mercapto-4(3H)-quinazolinone was used for the voltammetric determination of mercury(II). Mercury was preconcentrated onto the surface of the modified electrode only by the complexing effect of the modifier without application of potential (i.e. in open-circuit conditions). After exchange of the medium, the accumulated amount of mercury(II) was determined by differential pulse anodic stripping voltammetry. The response depended on the concentration of mercury in the bulk solution, preconcentration time, and other parameters. The detection limit was 0.1 g 1^–1 Hg(II) for a preconcentration time of 15 min. Preconcentration for suitable times yielded a linear calibration graph from 0.5 to 6000 g 1^–1 Hg(II). For multiple determinations (5 runs), the relative standard deviation was 5% for a concentration of 100 g 1^–1 Hg(II). The proposed procedure was used to determine trace mercury in plant and sewage sludge samples with good results.On leave from Hainan University, Hainan Peoples Republic of China     

Photovoltaic devices based on electrodeposited poly(3-methylthiophene) with tin oxide as the transparent electrode

We report on the use of electrodeposited poly(3-methylthiophene) (PMeT) in photovoltaic devices. Photocurrent measurements in devices with PMeT as the active conjugated polymer layer were carried out showing that the combination of Ni and tin oxide (TO) as electrode materials presents advantages relative to Al and TO. The choice of these electrode materials permits the carriers with the lowest mobility, the negative charge carriers, to be collected near the exciton generation/dissociation region, i.e. near the transparent TO electrode, avoiding the tendency for space charge accumulation and consequently the reduction of device efficiency. Electronic Publication