Development of a new sample pre-treatment procedure based on pressurized liquid extraction for the determination of metals in edible seaweed

A new, simple, fast and automated method based on acetic acid-pressurized liquid extraction (PLE) has been developed for the simultaneous extraction of major and trace elements (As, Ca, Cd, Co, Cr, K, Mg, Mn, Na, Pb, Sr and Zn) from edible seaweeds. The target elements have been simultaneously determined by inductively coupled plasma-optical emission spectrometry (ICP-OES). The influence of several extraction parameters (e.g. acetic acid concentration, extraction temperature, extraction time, pressure, number of cycles, particle size and diatomaceous earth (DE) mass/sample mass ratio) on the efficiency of metal leaching has been evaluated. The results showed that metal extraction efficiency depends on the mass ratio of the dispersing agent mass and the sample. The optimized procedure consisted of the following conditions: acetic acid (0.75 M) as an extracting solution, 5 min of extraction time, one extraction cycle at room temperature at a pressure of 10.3 MPa and addition of a dispersing agent (at a ratio of 5:1 over the sample mass). The leaching procedure was completed after 7 min (5 min extraction time plus 1 min purge time plus 1 min end relief time). Limits of detection and quantification and repeatability of the over all procedure have been assessed. Method validation was performed analysing two seaweed reference materials (NIES-03 Chlorella Kessleri and NIES-09 Sargasso). The developed extraction method has been applied to red (Dulse and Nori), green (Sea Lettuce) and brown (Kombu, Wakame and Sea Spaghetti) edible seaweeds.     

Multi-element determination in raft mussels by fast microwave-assisted acid leaching and inductively coupled plasma-optical emission spectrometry

Studies on the application of a short microwave irradiation cycle and the use of diluted acids to extract trace elements from raft mussel samples were developed. Multi-element determinations (Al, Ba, Cd, Cr, Cu, Fe, Mn, Pb, Sn, V and Zn) were carried out by inductively coupled plasma-optical emission spectrometry (ICP-OES). Parameters such as acid/oxidizing reagents (diluted nitric acid, hydrochloric acid and hydrogen peroxide) concentrations, acid/oxidizing solution volume, temperature, ramp time and hold time for the microwave heating were simultaneously studied by using an experimental design approach. The optimum conditions have showed the sample pre-treatment of 10 mussel samples to less than 3.0 min when a microwave power of 600 W and a controlled temperature of 65 °C were used. This time (hold time plus ramp time) is quite shorter than those reported for conventional microwave-assisted acid digestion procedures. Since temperature inside the reactor is not high, the venting time can be shorted to 15 min. In addition, the concentration of acid/oxidizing reagents needed to complete the acid leaching (2.5 M, 3.0 M and 0.5 % (m/v) for nitric acid, hydrochloric acid and hydrogen peroxide, respectively) is lower than the required concentration for a conventional microwave-assisted acid digestion (concentrated acids). The proposed method has showed a good repeatability of the overall method, and relative standard deviations between 11 and 2% were reached for 12 replicate microwave-assisted acid leaching and ICP-OES measurements. The method was finally validated by analyzing TORT-1 and GBW-08571 certified reference materials and it was successfully applied to fast multi-element determinations in several raft mussel samples.     

Comparison of ultrasound-assisted leaching with conventional and acid bomb digestion for determination of metals in sediment samples

In this paper, a sample preparation method based on ultrasound assisted leaching of Pb, Cu, Zn, Ni and Mn from river and pond sediment samples under ultrasonic effect has been described. Parameters influencing leaching such as sonication time, sample amount, particle size and extractant were fully optimized. Leachatants obtained upon sonication were directly nebulised into an air-acetylene flame for fast metal determination by atomic absorption spectrometry. The best conditions for metal leaching were as follows: a 25 min sonication time, a 0.5 g sample amount (in 25 mL solvent), a particle size < 63 μm and a mixture of concentrated HNO₃-HCIO₄-HF (2:1:1, v/v/v). Analytical results for the five metals by ultrasound-assisted leaching, acid bomb and conventional digestion methods showed a good agreement, thus indicating the possibility of using mild conditions for sample preparation instead of intensive treatments inherent with the digestion methods. In addition, this method reduces the time required for all treatments (leaching or digestion, heating to dryness, cooling and separation) with acid bomb digestion method (from ∼ 8 h to ∼ 1.5 h) and conventional acid digestion method (from ∼ 14 h to ∼ 1.5 h). The accuracy of the method was tested either by comparing obtained results with those of acid bomb and conventional digestion methods or by application on a standard reference materials. The average relative standard deviation of ultrasound assisted leaching method varied between 0.7-1.9% for N = 6, depending on the analyte.     

Evaluation of an in vitro method to estimate trace elements bioavailability in edible seaweeds

Raw edible seaweed harvested in the Galician coast (Northwestern Spain), including two red seaweed types (Dulse and Nori), three brown seaweed (Kombu, Wakame and Sea Spaghetti), one green seaweed (Sea Lettuce) and one microalgae (Spirulina platensis) were studied to assess trace elements bioavailability using an in vitro method (simulated gastric and intestinal digestion/dialysis). Similarly, a cooked seaweed sample (canned in brine) consisting of a mixture of two brown seaweed (Sea Spaghetti and Furbelows) and a derived product (Agar-Agar) from the red seaweed Gelidiumm sesquipedale, were also included in the study. The total trace element content as well as the non-dialyzable fractions was carried out after a microwave acid digestion of the seaweed samples by inductively coupled plasma-mass spectrometry (ICP-MS). The dialyzable fraction was determined without any pre-treatment by ICP-MS.PIPES buffer solution at a pH of 7.0 and dialysis membranes of 10 kDa molecular weight cut off (MWCO) were used for intestinal digestion. Accuracy of the method was assessed by analyzing a NIES-09 certified reference material (Sargasso seaweed). The accuracy of the in vitro procedure was established by a mass balance study which led to good accuracy of the whole in vitro process, after statistical evaluation (95% confidence interval). The highest dialyzability percentages (100 ± 0.2%) were obtained for Dulse in Mn and V.     

Microwave assisted extraction of iodine and bromine from edible seaweed for inductively coupled plasma-mass spectrometry determination

The feasibility of microwave energy to assist the solubilisation of edible seaweed samples by tetramethylammonium hydroxide (TMAH) has been investigated to extract iodine and bromine. Inductively coupled plasma-mass spectrometry (ICP-MS) has been used as a multi-element detector. Variables affecting the microwave assisted extraction/solubilisation (temperature, TMAH volume, ramp time and hold time) were firstly screened by applying a fractional factorial design (2^5-1 + 2), resolution V and 2 centre points. When extracting both halogens, results showed statistical significance (confidence interval of 95%) for TMAH volume and temperature, and also for the two order interaction between both variables. Therefore, these two variables were finally optimized by a 2² + star orthogonal central composite design with 5 centre points and 2 replicates, and optimum values of 200 °C and 10 mL for temperature and TMAH volume, respectively, were found. The extraction time (ramp and hold times) was found statistically non-significant, and values of 10 and 5 min were chosen for the ramp time and the hold time, respectively. This means a fast microwave heating cycle. Repeatability of the over-all procedure has been found to be 6% for both elements, while iodine and bromine concentrations of 24.6 and 19.9 ng g⁻¹, respectively, were established for the limit of detection. Accuracy of the method was assessed by analyzing the NIES-09 (Sargasso, Sargassum fulvellum) certified reference material (CRM) and the iodine and bromine concentrations found have been in good agreement with the indicative values for this CRM. Finally, the method was applied to several edible dried and canned seaweed samples.     

An ultrasound-assisted digestion method for the determination of toxic element concentrations in ash samples by inductively coupled plasma optical emission spectrometry

A method of ultrasound-assisted digestion followed by inductively coupled plasma optical emission spectrometry (ICP-OES) used for the determination of toxic element concentrations (arsenic, barium, cobalt, copper, lead, nickel, strontium, vanadium and zinc) in ash samples was developed. All the measurements were performed in robust plasma conditions which were tested by measuring the Mg(II) 280.270 nm/Mg(I) 285.213 nm line intensity ratios. The highest line intensity ratios were observed when a nebulizer gas flow of 0.6 L min⁻¹, auxiliary gas flow of 0.2 L min⁻¹ and plasma power of 1400 W were used for radially viewed plasma. The analysis of SRM 1633b showed that the ultrasound-assisted method developed is highly comparable with the microwave digestion method standardized by the United States Environmental Protection Agency (EPA-3052). The ultrasound-assisted digestion with a digestion solution of aqua regia and hydrofluoric acid (HF) resulted in recovery rates of over 81%. One exception is arsenic which resulted in recoveries of about 60% only; however, it could be digested with good recovery (>90%) using a digestion solution of 5 mL of water and 5 mL of aqua regia. The major advantage of the ultrasound-assisted digestion over microwave digestion is the high treatment rate (30 samples simultaneously with a sonication time of 18 min).     

Ultrasound-assisted solvent extraction of total polycyclic aromatic hydrocarbons from mussels followed by spectrofluorimetric determination

An ultrasound-assisted solvent extraction procedure has been optimised to speed up total polycyclic aromatic hydrocarbons (T-PAHs) extraction from mussel soft tissue. The T-PAHs releases have been evaluated by spectrofluorimetry (excitation and fluorescence emission wavelengths of 300 and 382 nm, respectively, and using chrysene as calibrant). Variables such as sonication time, ultrasound frequency, n-hexane volume, dichloromethane volume, number of repeated extractions with n-hexane and number of repeated extraction with dichloromethane were simultaneously studied by applying a Plackett-Burman design (PBD) approach. Results showed that ultrasound frequency and n-hexane and dichloromethane volumes were statistically significant variables (confidence interval of 95%). These last two variables were finally optimised by using central composite designs (CCD), yielding optimum n-hexane and dichloromethane volumes of 2.5 and 6.5 ml, respectively. The lowest T-PAHs releasing at high ultrasound frequency (35 kHz) led to choice the lowest ultrasound frequency (17 kHz) to perform the extraction. Variables such as sonication time and number of repeated extraction with n-hexane or dichloromethane were statistically non-significant and they were fixed at 10 min and the extraction with n-hexane and dichloromethane were performed once. The limit of detection was 0.021 μg g⁻¹ (referred to dried mass), the repeatability of the overall method was 4.7% (n = 9) and the analytical recoveries were between 98 and 105%. The proposed method was finally applied to 16 mussel samples (Mytilus galloprovincialis) from Ría de Arousa estuary (Galicia, northwest Spain).     

Tin determination in marine sediment, soil, coal fly ash and coal slurried samples by hydride generation-electrothermal atomic absorption spectrometry

Different procedures of tin hydride generation from aqueous and acidified slurries of marine sediment, soil, coal fly ash and coal samples, coupled to electrothermal atomic absorption spectrometry were optimised by using factorial designs. A batch mode generation system and Ir-treated graphite tubes were used for the hydride generation and atomisation, respectively. Eight variables, affecting the hydride generation and hydride transport efficiency (hydrochloric acid and sodium tetrahydroborate concentrations, particle size, acid volume and argon flow rate), the hydride trapping efficiency (trapping temperature and trapping time) and the atomisation efficiency (atomisation temperature) were studied and optimised. In addition, acid pre-treatment procedures assisted by ultrasonic energy were used for soil and coal matrices, to obtain acidified slurries and acid leachates. The involved variables were hydrochloric and nitric acid concentrations, exposure time to ultrasound, particle size and leaching solution volume. Adequate accuracy (41.5±0.8 and 1.4±0.2 mg kg⁻¹, for PACS-1 (sediment marine) and NIST-1633b (coal fly ash), respectively) were obtained by using aqueous slurry reference materials. In addition, values of 6.2±0.6 and 1.2±0.1 mg kg⁻¹ were assessed by analysing GBW-07401 (soil) and NIST-1632c (coal) certified reference materials.     

Ultrasound assisted extraction of phenolic compounds from grapes

A new ultrasound-assisted extraction method was developed for the determination of phenolic compounds present in grapes. Several extraction variables including extraction temperature (0–75 °C), output amplitude (20, 50 and 100%), duty cycle (0.2 s, 0.6 s and 1 s), the quantity of sample (0.5–2 g), and the total extraction time (3–15 min) were evaluated. One of the most widely used extraction methods of polyphenol extraction has been used as reference method. Three parameters were compared: total amount of phenolic compounds, total amount of anthocyanins and total amount of tannic components. The resulting method produced similar or higher recoveries for these three parameters; however a much shorter extraction time was needed: 6 min (ultrasound assisted extraction method) instead of 60 min (reference method).     

Determination of pesticides in seaweeds by pressurized liquid extraction and programmed temperature vaporization-based large volume injection–gas chromatography–tandem mass spectrometry

A rapid method for the simultaneous identification and quantification of pesticide residues in edible seaweed has been developed. Target analytes were three pyrethroid, a carbamate and two organophosphorus pesticides. The procedure consists of a pressurized liquid extraction (PLE) with integrated clean-up, followed by gas chromatography coupled to tandem mass spectrometry. Five PLE parameters were investigated using a screening design: temperature, static extraction time, number of cycles, percent of flush volume and quantitative composition of the n-hexane/ethyl acetate extraction solvent. The effect of the in-cell clean-up with Florisil^® and graphitized carbon black adsorbents was investigated using a Doehlert response surface design. Large volumes of sample extracts were injected using a programmed-temperature vaporizer (PTV-LVI) to improve both sensitivity and selectivity of measurements. Quantification was carried by the internal standard method with surrogate deuterated standards. The method showed excellent linearity (R² > 0.999) and precision (relative standard deviation, RSD ≤ 8%) for all compounds, with detection limits ranging from 0.3 pg g⁻¹ for chlorpyrifos-ethyl, to 3.0 pg g⁻¹ for carbaryl (23.1 pg g⁻¹ for deltamethrin). Recoveries in real seaweed samples were within the range 82–108%. The method was satisfactory validated for the analysis of wild and cultivated edible seaweeds. The presence of pyrethroid and organophosphorus pesticides in some of the samples was evidenced.     

Approach for rapid extraction and speciation of mercury using a microtip ultrasonic probe followed by LC-ICP-MS

A fast method for mercury extraction from biological samples based on the use of HCl leaching plus different enzymatic hydrolysis (with and without mercury complexing agents), and the use of focussed ultrasounds (2-mm microtip) is here proposed. Total mercury content in several biological samples was determined by FI-ICP-MS using a carrier solution consisting of 0.1% (v/v) HCl, 0.1% (v/v) 2-mercaptoethanol, to avoid memory effect, and 0.15% (w/v) KCl. For mercury speciation a RP18 chromatographic column coupled to ICP-MS was used. A mobile phase consisting of 0.1% (v/v) formic acid, 0.1% (v/v) HFBA, 2% (v/v) methanol, and 0.02% (w/v) mM l-cysteine at pH 2.1 was used for chromatographic separation of the mercury species in the sample extracts. Extraction procedures were validated by using 50 mg of tuna fish tissue CRM-463 (2.85 ± 0.16 mg kg⁻¹ for methylmercury). The recoveries obtained were 99 ± 3% and 93 ± 1% after acid leaching (HCl 7 M) and enzymatic extraction (15 mg protease type XIV in 2.5% (v/v) 2-mercaptoethanol), respectively. The optimal sonication conditions (5 min of exposure time and 40% of ultrasound amplitude) were applied to 5 mg of CRM-463 (88 ± 5%), 5 mg of mussel tissue (81 ± 11%) and to 2 mg of zebra fish embryos (90 ± 10%) obtaining good recoveries in all cases. Methylmecury was found to be the most abundant Hg specie in all samples. The developed method is simple and rapid (5 min sample treatment); it is suitable for very small samples and does not alter the original form of the mercury species. Thus, it is of special interest in those cases in which validation of the results may often be hampered by lack of sample availability.     

Comparison of slurry sampling and microwave-assisted digestion for calcium, magnesium, iron, copper and zinc determination in fish tissue samples by flame atomic absorption spectrometry

The development of a slurry sampling method for the determination of calcium, copper, iron, magnesium and zinc in fish tissue samples by flame atomic absorption spectrometry is described. In comparison with microwave-assisted digestion, the proposed method is simple, requires short time and eliminates total sample dissolution before analysis. Suspension medium was optimized for each analyte to obtain quantitative recoveries from fish tissue samples without matrix interferences. Nevertheless, iron recoveries higher than 46% were not found. Treatment of samples slurried in nitric acid by microwave irradiation for 15-30 s at 75-285 W permitted to achieve efficient recoveries for calcium, iron, magnesium and zinc. Further improvement in the matrix effects for iron determination was accomplished by the use of an additional step of short microwave-assisted suspension treatment. However, standard addition method was required for calcium and copper determination, being necessary hydrochloric acid as suspension medium for the last one. Although copper could not be determined in the certified reference material using microwave-assisted digestion, the accuracy of the slurry sampling method was verified for all the investigated analytes. Detection limits were 22.8 ± 8.0, 0.884 ± 0.092, 5.07 ± 0.76, 35.5 ± 0.7 and 1.17 ± 0.04 μg g⁻¹ for calcium, copper, iron, magnesium and zinc, respectively. The standard deviations obtained using slurry sampling method and microwave-assisted digestion were not significantly different, and the mean relative standard deviation of the over-all method (n = 3) of the slurry sampling method for different concentration levels was below 12%.     

Determination of methylmercury and inorganic mercury in water samples by slurry sampling cold vapor atomic absorption spectrometry in a flow injection system after preconcentration on silica C18 modified

A novel method for preconcentration of methylmercury and inorganic mercury from water samples was developed involving the determination of ng l⁻¹ levels of analytes retained on the silica C₁₈ solid sorbent, previous complexation with ammonium pyrrolidine dithiocarbamate (APDC), by slurry sampling cold vapor atomic absorption spectrometry (SS-CVAAS) in a flow injection (FI) system. Several variables were optimized affecting either the retention of both mercury species, such as APDC concentration, silica C₁₈ amount, agitation times, or their determination, including hydrochloric acid concentration in the suspension medium, peristaltic pump speed and argon flow-rate. A Plackett-Burman saturated factorial design permitted to differentiate the influential parameters on the preconcentration efficiency, which were after optimized by the sequential simplex method. The contact time between mercury containing solution and APDC, required to reach an efficient sorption, was decreased from 26 to 3 min by the use of sonication stirring instead of magnetic stirring. The use of 1 mol dm⁻³ hydrochloric acid suspension medium and 0.75% (m/v) sodium borohydride reducing agent permitted the selective determination of methylmercury. The combination of 5 mol dm⁻³ hydrochloric acid and 10⁻⁴% (m/v) sodium borohydride was used for the selective determination of inorganic mercury. The detection limits achieved for methylmercury and inorganic mercury determination under optimum conditions were 0.96 and 0.25 ng l⁻¹, respectively. The reliability of the proposed method for the determination of both mercury species in waters was checked by the analysis of samples spiked with known concentrations of methylmercury and inorganic mercury; quantitative recoveries were obtained.     

Determination of total mercury in nuts at ultratrace level

Total mercury, at μg kg⁻¹ level, was determined in different types of nuts (cashew nut, Brazil nuts, almond, pistachio, peanut, walnut) using a direct mercury analyser after previous sample defatting and by cold vapour atomic fluorescence spectrometry. There is not enough sensitivity in the second approach to determine Hg in previously digested samples due to the strong matrix effect. Mercury levels in 25 edible nut samples from Brazil and Spain were found in the range from 0.6 to 2.7 μg kg⁻¹ by using the pyrolysis of sample after the extraction of the nut fat. The accuracy of the proposed method was confirmed by analysing certified reference materials of Coal Fly Ash-NIST SRM 1633b, Fucus-IAEA 140 and three unpolished Rice Flour NIES-10. The observed results were in good agreement with the certified values. The recoveries of different amounts of mercury added to nut samples ranged from 94 to 101%. RSD values corresponding to three measurements varied between 2.0 and 14% and the limit of detection and quantification of the method were 0.08 and 0.3 μg kg⁻¹, respectively.     

Cadmium and lead determination in foods by beam injection flame furnace atomic absorption spectrometry after ultrasound-assisted sample preparation

A simple method for cadmium and lead determination in foods by beam injection flame furnace atomic absorption spectrometry (BIFF-AAS) was proposed. Food slurries were prepared by transferring an exact amount of cryogenic-ground homogenized material (50-100 mg) to centrifuge tubes, followed by addition of 5 ml (up to 2.8 mol l⁻¹) nitric acid solution and sonication in an ultrasonic bath during 5-10 min. Thereafter, slurries were diluted with water to 10 ml, centrifuged during 5 min at 5400 rpm and 400 μl aliquot of the supernatant was analyzed by BIFF-AAS. The detection limits based on peak height measurements were 0.03 μg g⁻¹ Cd and 1.6 μg g⁻¹ Pb for 2% (m/v) slurry (200 mg/10 ml). For method validation, the certified reference materials Pig Kidney (BCR 186) and Rice Flour (NIES 10) were used. Quantitative cadmium and lead recoveries were obtained and no statistical differences were found at 95% level by applying the t-test.     

Ultrasound assisted pseudo-digestion of street dust samples prior to determination by atomic absorption spectrometry

A sample preparation method based on ultrasound assisted pseudo-digestion of Pb, Cu, Zn and Ni from street dust samples under ultrasonic effect has been described. Parameters influencing pseudo-digestion, such as sonication time, sample mass, particle size and solvent system were fully optimized. Final solutions obtained upon sonication were analyzed by atomic absorption spectrometry. The best conditions for metal pseudo-digestion were as follows: a 25 min sonication time, a 0.3 g sample mass (in 25 ml solvent), a particle size <63 μm and a mixture of concentrated HNO₃-HClO₄-HF (2:1:1, v/v/v). Analytical results for the four metals by ultrasound assisted pseudo-digestion, acid bomb and conventional wet digestion methods showed a good agreement, thus indicating the possibility of using mild conditions for sample preparation instead of intensive treatments inherent with the digestion methods. In addition, this method reduces the time required for all treatments (pseudo-digestion or digestion, heating to dryness, cooling and separation) with acid bomb and conventional wet digestion methods approximately from 9 to 1 h. The accuracy of the method was tested either by comparing obtained results with those of acid bomb and conventional wet digestion methods or by application on two standard reference materials. The average relative standard deviation of ultrasound assisted pseudo-digestion method varied between 0.9 and 1.8% for N = 12, depending on the analyte.     

Microwave-assisted alkaline digestion combined with microwave-assisted distillation for the determination of iodide and total iodine in edible seaweed by catalytic spectrophotometry

Microwave energy has been novelty applied to speed up a tetramethylammonium hydroxide (TMAH) alkaline digestion of seaweed samples and to assist distillation of iodine from seaweed alkaline digests. Iodide in the alkaline digests from seaweed and distilled iodine, reduced back to iodine in a hydroxylamine hydrochloride solution, was determined by a catalytic spectrophotometric method based on the catalytic effect of iodide on the oxidation of As(III) by Ce(IV) in H₂SO₄/HCl medium (Sandell-Kolthoff reaction). The determination of iodide was directly performed in the alkaline digests, while total iodine was assessed by analyzing the hydroxylamine hydrochloride solution after the distillation process. Microwave-assisted alkaline digestion was performed using 7.5 mL of TMAH and irradiating samples at 670 W for two 5.5 min steps. Microwave-assisted distillation was carried out using 4.0 mL of the alkaline digest and 3 mL of a 2.2 M hydrochloric acid and 0.05% (m/v) sodium nitrite solution, with a microwave power at 670 W for two 90 s steps. The distillate (iodine vapor) was bubbled in 10 mL of a 500 μg mL⁻¹ hydroxylamine hydrochloride solution (accepting solution). The linear calibration ranges were 0.30-20.0 and 0.40-20.0 μg L⁻¹ for iodide determination and total iodine determination, respectively. The limit of detection was 9.2 μg g⁻¹ for iodide and 28.5 μg g⁻¹ for total iodine. Repeatability of the overall procedures, expressed as R.S.D. for 11 determinations, was 2.6% for 196.3 μg g⁻¹ of iodide measured after microwave-assisted alkaline digestion, and 5.8% for 954.3 μg g⁻¹ of total iodine by microwave-assisted alkaline digestion followed by microwave-assisted distillation. Finally, accuracy of the methods was assessed by analyzing the NIST-09 (Sargasso) certified reference material and the methods were applied to the determination of iodide and total iodine in different Atlantic edible seaweed samples with satisfactory results.     

A dual column system using agarose-based adsorbents for preconcentration and speciation of chromium in water

Three different agarose-based chelating adsorbents with, respectively, iminodiacetic acid (IDA), tris(2-aminoethyl)amine (TREN) and dipicolylamine (DPA) functional groups and an agarose-based anion exchanger (Q-Sepharose), were studied for the separation and preconcentration of Cr(III) and Cr(VI) species in water. Column recoveries of all the adsorbents were plotted against pH, and it was found that at pH 3.0 the IDA adsorbent selectively adsorbs Cr(III), with a 100 ± 1.0% recovery. The Q-Sepharose, on the other hand, accumulated only Cr(VI) at this pH, again with a recovery of 100 ± 1.0%. A dual column system was accordingly designed, using the two adsorbents in tandem, for the separation and preconcentration of the chromium species.The effects of pH, sample flow rate, column length, eluent type, eluent volume, acid concentration and interfering ions on the recoveries of Cr(III) and Cr(VI) were carefully studied. It was shown that by passing test solutions, at pH 3.0; through the dual column system, the two chromium species could be individually collected on the columns, respectively, and eluted, one after the other. A portion of 2 mol l⁻¹ hydrochloric acid was used for elution of each column before final measurement by flame AAS method. A preconcentration factor of 12, a detection limit of 7.7 ± 0.1 μg l⁻¹ and a precision expressed as relative standard deviation of 0.4% (at 0.3 mg l⁻¹) were achieved for six replicates.Application of the developed method to the determination of chromium species in spiked river and tap water and wastewater samples, from a dye production plant, resulted in excellent agreements with accepted concentrations.     

Coupling continuous ultrasound-assisted extraction, preconcentration and flame atomic absorption spectrometric detection for the determination of cadmium and lead in mussel samples

Continuous ultrasound-assisted extraction has been coupled with preconcentration and flame atomic absorption spectrometry for the determination of cadmium and lead in mussel samples. Experimental designs were used for the optimisation of the leaching and preconcentration steps. The use of diluted nitric acid as extractant in the continuous mode at a flow rate of 3.5 ml min⁻¹ and room temperature was sufficient for quantitative extraction of these trace metals. A minicolumn containing a chelating resin (Chelite P, with aminomethylphosphoric acid groups) was proved as an excellent material for the quantitative preconcentration of cadmium and lead prior to their flame atomic absorption detection. A flow injection manifold was used as interface for coupling the three analytical steps, which allowed the automation of the whole analytical process. A good precision of the whole procedure (2.0 and 2.3%), high enrichment factors (20.5 and 11.8) and a detection limit of 0.011 and 0.25 μg g⁻¹ for cadmium and lead, respectively, were obtained for 80 mg of sample. The sample throughputs were ca. 16 and 14 samples h⁻¹ for cadmium and lead, respectively. The accuracy of the analytical procedures was verified by using a standard reference material (BCR 278-R, mussel tissue) and the results were in good agreement with the certified values. The method was successfully applied to the determination of trace amounts of cadmium and lead in mussel samples from the coast of Galicia (NW, Spain).     

Speciation of chromium in wastewater and sludge by extraction with liquid anion exchanger Amberlite LA-2 and electrothermal atomic absorption spectrometry

A simple, integrated method for the speciation of chromium in wastewater and sewage sludge was developed, utilising liquid anion exchange by Amberlite LA-2 (LAES) and final determination by electrothermal atomic absorption spectrometry (ETAAS). Samples were filtered through a 0.45 μm membrane filter and chromium species were determined in filtered water samples and in sludge on the filters. In the former case (filtrate), total Cr was determined directly by ETAAS, while for the determination of Cr(VI) the filtrate was buffered to pH 6.4, extracted with LAES and Cr(VI) was determined in the organic extract. Cr(III) was determined by the difference. In the latter case (filter), the filters were leached with an alkaline buffer solution (pH 12.7) and the supernatant was subjected to the same extraction procedure. For the determination of total leachable Cr, the filters were subjected to acid leaching with dilute HNO₃ (pH 1) and the supernatant was subjected to ETAAS, after appropriate dilution with water. Then, Cr(III) was determined by the difference. The limits of detection (LOD) were 0.39 and 0.45 μg l⁻¹ for total Cr and Cr(VI), respectively, in the dissolved phase and 2.10 and 0.87 ng g⁻¹ for total Cr and Cr(VI) in the suspended solids. The recoveries of total Cr and Cr(VI) in filtrated wastewater samples and filters were quantitative, ranged from 93 to 106%. The effect of time and temperature of sonication and suspended solids concentration on total Cr and Cr(VI) recovery was studied. No significant difference in recoveries was obtained for sonication temperatures between 30 and 70 °C. However, sonication time equal to or higher than 30 min and concentration of suspended solids equal to or less than 30 mg significantly improved Cr recovery. The ETAAS program for the determination of Cr(VI) in Amberlite/MIBK extract was carefully optimised in the absence of a chemical modifier to avoid memory effects. The developed analytical method was applied for the determination of chromium species in wastewater and suspended solids of a municipal and a lab-scale wastewater treatment plant.