Utilization of electric arc furnace dust as an admixture to Portland cement pastes

Electric arc furnace dust (EAFD) is termed as a hazardous waste due to its contamination with heavy metals. Inertization of such very fine dust can be occurred via stabilization and solidification process within the hydrated Portland cement matrix. In this paper, the effect of the addition of various ratios of EAFD on the properties of the hardened Portland cement paste was investigated. Compressive strength, chemically combine water and free lime contents were determined. In addition, phase composition using XRD; DTA analysis; as well as microstructure of the formed hydrates for some selected samples were investigated using SEM. The obtained results showed that the paste containing 1/mass% EAFD give the highest compressive strength values at most hydration ages, specially the later ages, compared to the neat Portland cement blank paste. Whileas, the pastes containing 3 and 5/mass% EAFD showed lower values of compressive strength compared to those of the blank paste.     

Beneficiation of zinc from electric arc furnace dust using hydrometallurgical approach

Zinc bearing wastes such as electric arc furnace dust (EAFD) obtained from steel making constitute an important resource for zinc extraction. Inclusion of heavy metals such as Pb, Cd, Cu, Cr, Ni, etc., in these wastes makes them hazardous to use and/or dispose. In the present research work, leaching kinetics of EAFD with sulfuric acid has been investigated and various experimental parameters such as concentration of lixiviant, stirring rate, sample particle size, liquid/solid proportion, and temperature of the reaction have been optimized. It has been found that the dissolution rate of EAFD increases with rise in temperature, acidic strength, rate of stirring, liquid to solid proportion and with reduction in EAFD particle size. From the analysis of leaching kinetic data by means of graphical and statistical methods, it has been evaluated that the leaching kinetics of EAFD is dictated by surface diffusion reaction. Apparent energy of activation for the leaching reaction of EAFD with sulfuric acid is found to be 13.1 kJ mol^–1 within the temperature range of 308 to 358 K.     

Direct determination of uranium in sintered deeply depleted uranium oxide pellets by wavelength dispersive X-ray fluorescence spectrometry

This paper presents studies on direct non-destructive determination of uranium in sintered deeply depleted (DD) uranium oxide (UO₂) pellets by wavelength dispersive X-ray fluorescence (WDXRF) spectrometry. A special collet was designed and fabricated for holding the sintered DDUO₂ pellets for direct analysis, thus avoiding the sample preparation steps. The samples were analyzed using a calibration plot obtained from WDXRF spectra of matrix matched calibration standards. The WDXRF determined uranium values were found to be in very close agreement with titrimetric values and has reproducibility better than 0.05% (RSD, 1 s, n = 10) for the sintered DDUO₂ pellets having U: 86.81–88.04 wt%.

     

High temperature properties of by-product cold bonded pellets containing blast furnace flue dust

In this investigation, the fundamental reactions occurring during the heat treatment of cold bonded pellets (CBP) comprised of iron and steelmaking by-products have been studied. Blast furnace (BF) flue dust, which contains fractions of coal and coke particles, has been included in the CBP blend as a source of solid reductant. Thermal analysis was performed on CBP samples in inert atmosphere at a heating rate of 10 °C/min in order to observe their high temperature properties, specifically, the mechanisms of self-reduction within CBPs. Both endothermic and exothermic reactions were observed during heating. The gases generated during thermal analysis were analyzed using a quadropole mass spectrometer (QMS). Furthermore, CBP samples heated to several different temperatures and quenched in argon were analyzed using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Results from this investigation demonstrate that the decomposition of hydrates and carbonates in CBP samples contribute, as gaseous intermediates, to an earlier reduction of contained iron oxides. The gaseous intermediates are responsible for an initial gasification of carbon contained in blast furnace flue dust leading to low temperature iron oxide reduction. The step-wise reduction of iron oxides in CBPs at the given conditions begins at ∼500 °C and is nearly completed at 1200 °C. This work can help to provide a fundamental understanding of the reduction characteristics of iron and steelmaking by-product agglomerates.     

Graphite furnace for alternative combination with d.c. arc or inductively coupled plasma. Introduction and analysis of solid samples

Summary A graphite furnace and d.c. arc combined source with the use of halogenating atmosphere in the furnace is described. The construction makes possible the introduction and analysis of both liquid and solid samples at minimum risk of contamination. Spectrographic detection resulted in background equivalent mass values below 10 ng for 22 from 36 elements applied in solution (Ar + CCl₄ atmosphere and NaCl matrix). The intensity-time profiles indicated high rates of distillation of the impurities (including B, Cr, Hf, Mo, Ti, V, W and Zr) from silicon carbide and silicon nitride samples in the first 40 s of heating under chlorination (CCl₄ vapour). Two versions of the exit part of the furnace are described for coupling to an ICP source; one of them has been used for the determination of titanium in alumina (spectrometric detection). Standardization with solution standards for solid sample analysis was unsuccessful. Based on the analytical curve obtained with variable amounts of solid standards (5–20 mg), a detection limit of 0.32 g/g Ti was found for 20 mg alumina.     

External calibration strategy for trace element quantification in botanical samples by LA-ICP-MS using filter paper

The use of reference solutions dispersed on filter paper discs is proposed for the first time as an external calibration strategy for matrix matching and determination of As, Cd, Co, Cr, Cu, Mn, Ni, Pb, Sr, V and Zn in plants by laser ablation-inductively coupled plasma mass spectrometry (LA-ICP-MS). The procedure is based on the use of filter paper discs as support for aqueous reference solutions, which are further evaporated, resulting in solid standards with concentrations up to 250 μg g⁻¹ of each element. The use of filter paper for calibration is proposed as matrix matched standards due to the similarities of this material with botanical samples, regarding to carbon concentration and its distribution through both matrices. These characteristics allowed the use of ¹³C as internal standard (IS) during the analysis by LA-ICP-MS. In this way, parameters as analyte signal normalization with ¹³C, carrier gas flow rate, laser energy, spot size, and calibration range were monitored. The calibration procedure using solution deposition on filter paper discs resulted in precision improvement when ¹³C was used as IS. The method precision was calculated by the analysis of a certified reference material (CRM) of botanical matrix, considering the RSD obtained for 5 line scans and was lower than 20%. Accuracy of LA-ICP-MS determinations were evaluated by analysis of four CRM pellets of botanical composition, as well as by comparison with results obtained by ICP-MS using solution nebulization after microwave assisted digestion. Plant samples of unknown elemental composition were analyzed by the proposed LA method and good agreement were obtained with results of solution analysis. Limits of detection (LOD) established for LA-ICP-MS were obtained by the ablation of 10 lines on the filter paper disc containing 40 μL of 5% HNO₃ (v v⁻¹) as calibration blank. Values ranged from 0.05 to 0.81  μg g⁻¹. Overall, the use of filter paper as support for dried aqueous standards showed to be a useful strategy for calibration and plant analysis by LA-ICP-MS.     

Solid sampling-graphite furnace atomic absorption spectrometry for the direct determination of silver at trace and ultratrace levels

In this work, the possibilities of solid sampling-graphite furnace atomic absorption spectrometry for the direct determination of silver in solid samples of very different nature (a biological sample, a soil, an ore concentrate and a polymer) and showing substantial differences in their analyte content (from approximately, 40 ng g⁻¹ up to 350 μg g⁻¹) have been evaluated, the goal always being to develop fast methods, only relying on the use of aqueous standards for calibration.Different factors had to be taken into account in order to develop suitable procedures for all the samples under investigation. Among the most important ones, the following can be mentioned: (i) optimization of the temperature program in order to selectively atomize the analyte; (ii) the use of chemical modifiers (such as Pd or HNO₃), depending on the sample characteristics; (iii) appropriate wavelength, argon flow and sample mass selection (depending on the analyte content); (iv) the use of 3-field mode Zeeman-effect background correction in order to further expand the linear range up to 1000 ng of Ag, which was needed for analysis of the sample showing the highest Ag content (polypropylene).The procedures finally proposed show interesting features for the determination of silver in solid samples: the advantage of using aqueous standard solutions for calibration, a high sample throughput (approximately, 15 min per sample), a low detection limit (2 ng g⁻¹), sufficient precision (R.S.D. values in the vicinity of 10%) and a reduced risk of analyte losses and contamination.     

Chromium determination in pharmaceutical grade barium sulfate by solid sampling electrothermal atomic absorption spectrometry with Zeeman-effect background correction

A procedure for chromium (Cr) determination in pharmaceutical grade barium sulfate by direct solid sampling electrothermal atomic absorption spectrometry (DSS-ET AAS) with Zeeman-effect background correction was developed. Operational conditions for the proposed procedure and the use of citric acid, ammonium phosphate, palladium and magnesium nitrate as chemical modifiers were evaluated. Pyrolysis and atomization temperatures were set at 1500 and 2400 °C, respectively and the use of matrix modifiers did not improve these conditions. Graphite platform presented high degradation rate, but minima changes were observed in the sensitivity or signal profile. Samples (0.3-1 mg) were weighted and introduced into the furnace using a manual solid sampling system. The linear concentration range of the calibration curve was from 100 to 1800 pg (R² > 0.995). The characteristic mass was 7.7 pg and the limit of detection was 2.4 pg. Chromium concentration in commercial samples ranged from 0.45 to 1.06 μg g⁻¹ and these results were confirmed by standard addition method. The mean reproducibility was 12% (n = 20 in a 3-day period) and repeatability was less than 9%. Results obtained using inductively coupled plasma optical emission spectrometry and conventional electrothermal atomic absorption spectrometry after extraction with HNO₃ were around 20% lower than those obtained by the proposed procedure. It was assumed that the low results were due to incomplete extraction even using hard conditions related to temperature and pressure. The proposed procedure by DSS-ET AAS provided some advantages related to recommended pharmacopoeias methodology, as lower risks of contamination and analyte losses, higher specificity, accuracy and sensitivity, no toxic or unstable reagents are required, and calibration with aqueous standards was feasible.     

Determination of trace impurities in boron nitride by graphite furnace atomic absorption spectrometry and electrothermal vaporization inductively coupled plasma optical emission spectrometry using solid sampling

Two digestion-free methods for trace analysis of boron nitride based on graphite furnace atomic absorption spectrometry (GFAAS) and electrothermal vaporization inductively coupled plasma spectrometry optical emission (ETV-ICP-OES) using direct solid sampling have been developed and applied to the determination of Al, Ca, Cr, Cu, Fe, Mg, Mn, Si, Ti and Zr in four boron nitride materials in concentration intervals of 1–23, 54–735, 0.05–21, 0.005–1.3, 1.6–112, 4.5–20, 0.03–1.8, 6–46, 38–170 and 0.4–2.3 μg g^− 1, respectively. At optimized experimental conditions, with both methods, effective in-situ analyte/matrix separation was achieved and calibration could be performed using calibration curves measured with aqueous standard solutions. In solid sampling GFAAS, before sampling, the platform was covered with graphite powder and, for determination of Si, also the Pd/Mg(NO₃)₂ modifier was used. In the determination of all analyte elements by solid sampling ETV-ICP-OES, Freon R12 was added to argon carrier gas. For solid sampling GFAAS and ETV-ICP-OES, the achievable limits of detection were within 5 (Cu)–130 (Si) ng g^− 1 and 8 (Cu)–200 (Si) ng g^− 1, respectively. The results obtained by these two methods for four boron nitride materials of different purity grades are compared each with the other and with those obtained in analysis of digests by ICP-OES. The performance of the two solid sampling methods is compared and discussed.     

Matrix effect in high‐performance liquid chromatography‐tandem mass spectrometry analysis of antibiotics in environmental water samples

This paper describes the matrix effect during the analysis of ten antibiotic compounds in water by SPE followed by HPLC‐ESI‐MS/MS. The target analytes were tetracycline, oxytetracycline (tetracyclines), sulfathiazole, sulfamethazine, sulfadiazine (sulfonamides), erythromycin‐H₂O, roxithromycine, spiramycin (macrolides), ofloxacin, and norfloxacin (quinolones). The matrix effect was examined for internal standards and the target analytes in five different water matrixes, with signal suppression being increased in the order: ultrapure water, tap water, river water, sewage effluent, and sewage influent. A combined application of the internal standards and matrix‐matched extract calibration was shown to be successful in compensating the matrix effect for the analytes. The procedural recovery of the target compounds in sewage effluents and influents was higher than in river water samples, which was further enhanced by sample acidification to pH 2. The validity of the internal standard based matrix‐matched calibration approach was verified by the standard addition method.     

Fast heating induced impulse halogenation of refractory sample components in electrothermal atomic absorption spectrometry by direct injection of a liquid halogenating agent

A novel electrothermal atomic absorption spectrometry (ETAAS) method was developed for the halogenation of refractory sample components (Er, Nd and Nb) of lithium niobate (LiNbO₃) and bismuth tellurite (Bi₂TeO₅) optical single crystals to overcome memory effects and carry-over. For this purpose, the cleaning step of a regular graphite furnace heating program was replaced with a halogenation cycle. In this cycle, after the graphite tube cooled to room temperature, a 20 μL aliquot of liquid carbon tetrachloride (CCl₄) was dispensed with a conventional autosampler into the graphite tube. The CCl₄ was partially dried at 80 °C under the mini-flow (40 cm³ min⁻¹) condition of the Ar internal furnace gas (IFG), then the residue was decomposed (pyrolyzed) by fast furnace heating at 1900-2100 °C under interrupted flow of the IFG. This step was followed by a clean-out stage at 2100 °C under the maximum flow of the IFG. The advantage of the present method is that it does not require any alteration to the graphite furnace gas supply system in contrast to most of the formerly introduced halogenation techniques.The effectiveness of the halogenation method was verified with the determination of Er and Nd dopants in the optical crystals. In these analyses, a sensitivity decrease was observed, which was likely due to the enhanced deterioration of the graphite tube surface. Therefore, the application of mathematical correction (resloping) of the calibration was also required. The calibration curves were linear up to 1.5 and 10 μmol L⁻¹ for Er and Nd, respectively. Characteristic masses of 18 and 241 pg and the limit of detection (LOD) values of 0.017 and 0.27 μmol L⁻¹ were found for Er and Nd, respectively. These LOD data correspond to 0.68 μmol mol⁻¹ Er and 11 μmol mol⁻¹ Nd in solid bismuth tellurite samples. The analytical results were compared with those obtained by a conventional ETAAS method and validated with X-ray fluorescence spectrometry analysis.     

Vapor phase matrix extraction of high purity di-boron trioxide and trace analysis using electrothermal AAS

A method has been developed for the determination of Al, Cd, Cr, Cu, Fe, Mg, Mn, Ni, Sb, Sn and Zn at trace levels in high purity di-boron trioxide using ETAAS. The boron trioxide matrix was eliminated as trimethyl borate ester in a multiplex vapor phase matrix extraction (MVPME) device using a mixture of glycerol and methanol. In this MVPME device, in situ reagent purification, sample digestion and simultaneous matrix elimination were achieved by a single step in closed condition, which in combined effect reduce the process blanks. The matrix extraction procedure allows determination of trace elemental impurities by electrothermal atomic absorption spectrometry (ETAAS) with fast furnace analysis (without an ashing step and modifier) and calibration against aqueous standards. The performance and accuracy of the vapor phase matrix elimination technique are compared to those of suprapur grade hydrofluoric acid solution in two ways; (i) matrix separation as BF₃ over hot plate and (ii) in situ matrix elimination inside graphite furnaces. The method detection limits calculated from blank samples are in the range of 0.5 (Ni) and 2.9 (Al) ng g⁻¹. Thus the MVPME-based sample preparation approach is well suited for the trace analysis of high purity di-boron trioxide used in microelectronics applications.     

Solid sampling-graphite furnace atomic absorption spectrometry for the direct determination of boron in plant tissues

In this work, the potential of graphite furnace atomic absorption spectrometry for the direct determination of B in plant tissues has been investigated. Three certified reference materials (NIST SRM 1570a spinach leaves, NIST SRM 1573a tomato leaves and BCR CRM 679 white cabbage) were selected for this study, the goal always being to develop a fast procedure that could be robust enough to provide a satisfactory performance for all of them, without any modifications in the conditions applied.The use of a suitable chemical modifier was found to be essential for obtaining a reproducible and sufficiently sensitive signal for boron solutions. In this regard, the performance of the combination of citric acid plus W (added as a permanent modifier) was noteworthy, resulting in well-defined signal profiles, a remarkable analyte stabilization during the pyrolysis step (up to 2100 °C) and minimal memory effects. This mixture of modifiers provided a good performance for the direct analysis of solid samples as well, but only if a suitable temperature program, favoring the interaction between the analyte and the modifiers, was used. Thus, such a temperature program, with two pyrolysis steps and the addition of NH₄NO₃ in order to carry out the in situ sample microdigestion, was optimized. Under these conditions, the peak areas obtained for both solid samples and aqueous standards were comparable.Finally, the analysis of the samples was carried out. In all cases, a good agreement with the certified values was obtained, while R.S.D. values ranged between 6 and 10%. It can be concluded that the method proposed shows significant advantages for the determination of this complicated element in solid samples such as the use of aqueous standards for calibration, a high sample throughput (20 min per sample), a suitable limit of detection (0.3 μg g⁻¹) and reduced risk of analyte losses and contamination.     

Evaluation of C18 adsorbent cartridges for sampling and derivatization of primary amines in air

The sampling efficiency of C₁₈ solid-phase extraction cartridges was investigated for methylamine, ethylamine, propylamine, butylamine and pentylamine, in air. Determination of these analytes was based on derivatization with o-phthaldialdehyde-N-acetylcysteine (OPA-NAC) on the solid support and fluorescence detection at λ_excitation=330 nm and λ_emission=440 nm of the eluted derivatives. The calibration model derived from aqueous standards was statistically comparable with the calibration model for air standards. Aqueous amines can be used as standards. The method was useful for calculating short-term exposure limits (STEL). A sampling time of 15 min at 30 ml min⁻¹ was employed. Good recoveries for amines alone and their mixtures were obtained from air and water samples, 98±14 and 97±12% (mean ), respectively. Recovery values were independent of amine concentration. The detection limits varied between 0.16 and 0.52 μg per sample (0.35 and 1.18 mg m⁻³, respectively) and the calibration graphs were linear in the range 0.5-2 μg per sample except for pentylamine, which was 1.5-5 μg per sample. The utility of the method was demonstrated for the estimation of methylamine in two generated air samples.     

Determination of traces of Ni in Li(2)CO(3)/Na(2)CO(3) melts by graphite furnace atomic absorption spectrometry

A graphite furnace atomic absorption method is described for the determination of traces of Ni in 52 mole percent (mol.%) Li₂CO₃ and 48 mol.% Na₂CO₃ melts after dissolution of the sample in dilute nitric acid. Maximum pyrolysis and optimum atomisation temperatures for the analyte were determined in the presence of the Li and Na matrix constituents. Pre-pyrolysed ascorbic acid (typical amount of 5 μg) has been used as chemical modifier for effectively suppressing the chemical and spectral interferences of the Li/Na matrix, thus that the analysis can be conducted using acid-matched standard solutions. The results of the Ni analysis in synthetic sample solutions by calibration graph against acid-matched standards well agree with those obtained by the method of standard additions. Recoveries ranged from 99 to 101% and the relative standard deviation is around 3% at the 20 μg L⁻¹ level. Moreover, the use of the chemical modifier leads to an improvement of the lifetime of the graphite tube. The Ni detection limit (3σ) in Li/Na carbonate melts for the proposed method is similar to that obtained in aqueous solution, i.e. 5 × 10⁻⁸ g analyte per gram of (Li_0.52Na_0.48) ₂CO₃ melt. This method is successfully applied to the determination of nickel in real carbonate melt samples.     

Tandem focused ultrasound (TFU) combined with fast furnace analysis as an improved methodology for total mercury determination in human urine by electrothermal-atomic absorption spectrometry

A new sample preparation procedure based on tandem (that is, different diameter probe sonicators used in the same sample treatment) focused ultrasound (TFU) for mercury separation, preconcentration and back-extraction in aqueous solution from human urine has been developed. The urine is first oxidized with KMnO₄/HCl/focused ultrasound (6 mm probe). Secondly, the mercury is extracted and preconcentrated with dithizone and cyclohexane. Finally, the mercury is back-extracted and preconcentrated again with the aid of focused ultrasound (3 mm probe). The procedure allows determining mercury by electrothermal atomic absorption spectrometry with fast furnace analysis and calibration against aqueous standards. Matrix modification is provided by the chemicals used in the sample treatment. The procedure is accomplished with low sample volume (8.5 ml). Low volume and low concentration reagents are used. The sample treatment is rapid (less than 3 min per sample) and avoids the use of organic phase in the graphite furnace. The preconcentration factor used in this work was 14. The limit of detection and the limit of quantification in urine were, respectively, 0.27 and 0.9 μg l⁻¹. The relative standard deviation of aqueous standards (n=10) was 4% for a concentration of 100 μg l⁻¹ and 5% for a concentration of 400 μg l⁻¹. Recoveries from spiked urine with inorganic mercury, methyl-mercury, phenyl-mercury and diphenyl-mercury ranged from 86 to 98%.     

Ionic liquid based dispersive liquid–liquid microextraction for the extraction of pesticides from bananas

This paper describes a dispersive liquid–liquid microextraction (DLLME) procedure using room temperature ionic liquids (RTILs) coupled to high-performance liquid chromatography with diode array detection capable of quantifying trace amounts of eight pesticides (i.e. thiophanate-methyl, carbofuran, carbaryl, tebuconazole, iprodione, oxyfluorfen, hexythiazox and fenazaquin) in bananas. Fruit samples were first homogenized and extracted (1 g) with acetonitrile and after suitable evaporation and reconstitution of the extract in 10 mL of water, a DLLME procedure using 1-hexyl-3-methylimidazolium hexafluorophosphate ([C₆MIM][PF₆]) as extraction solvent was used. Experimental conditions affecting the DLLME procedure (sample pH, sodium chloride percentage, ionic liquid amount and volume of disperser solvent) were optimized by means of an experimental design. In order to determine the presence of a matrix effect, calibration curves for standards and fortified banana extracts (matrix matched calibration) were studied. Mean recovery values of the extraction of the pesticides from banana samples were in the range of 69–97% (except for thiophanate-methyl and carbofuran, which were 53–63%) with a relative standard deviation lower than 8.7% in all cases. Limits of detection achieved (0.320–4.66 μg/kg) were below the harmonized maximum residue limits established by the European Union (EU). The proposed method, was also applied to the analysis of this group of pesticides in nine banana samples taken from the local markets of the Canary Islands (Spain). To the best of our knowledge, this is the first application of RTILs as extraction solvents for DLLME of pesticides from samples different than water.     

Direct determination of manganese in vitamin-mineral tablets using solid sampling electrothermal atomic absorption spectrometry

Manganese in vitamin-minerals tablets was determined by solid sampling electrothermal atomic absorption spectrometry (SS-ETAAS) using three different calibration methods, namely calibration against aqueous standards, standard addition with aqueous standards on solid samples and calibration against solid certified standards. Samples were only finely ground and introduced directly into the furnace by means of solid autosampler system without any dissolving process. Effects of different calibration techniques, temperatures and heating rates of atomization and pyrolysis steps on the accuracy and precision of the analyte elements were investigated. After optimization of the experimental parameters, there is good agreement (at 95% confidence level) between the results obtained by solid sampling and those obtained by acid digestion of samples.     

Laser-induced breakdown spectroscopy for determination of uranium in thorium-uranium mixed oxide fuel materials

Laser-induced breakdown spectroscopy (LIBS) has been developed for determining the percentage of uranium in thorium-uranium mixed oxide fuel samples required as a part of the chemical quality assurance of fuel materials. The experimental parameters were optimized using mixed oxide pellets prepared from 1:1 (w/w) mixture of thorium-uranium mixed oxide standards and using boric acid as a binder. Calibration curves were established using U(II) 263.553 nm, U(II) 367.007 nm, U(II) 447.233 nm and U(II) 454.363 nm emission lines. The uranium amount determined in two synthetic mixed oxide samples using calibration curves agreed well with that of the expected values. Except for U(II) 263.553 nm, all the other emission lines exhibited a saturation effect due to self-absorption when U amount exceeded 20 wt.% in the Th-U mixture. The present method will be useful for fast and routine determination of uranium in mixed oxide samples of Th and U, without the need for dissolution, which is difficult and time consuming due to the refractory nature of ThO₂. The methodology developed is encouraging since a very good analytical agreement was obtained considering the limited resolution of the spectrometer employed in the work.     

Application of Fourier-transform infrared (FT-IR) transmission spectroscopy for the estimation of roxithromycin in pharmaceutical formulations

A quick and reliable analytical method for the quantitative assessment of roxithromycin in pharmaceutical formulations was developed using Fourier-transform infrared (FT-IR) transmission spectroscopy for routine quality control. The sample preparation was avoided except grinding for pellet formation and eliminated the use of toxic solvents. For the determination of roxithromycin, conventional KBr was used in the form of pellets for acquisition of the FT-IR spectra of standards and samples. The calibration model was developed based on simple Beer's law using the FT-IR carbonyl region (CO) from 1765 to 1705 cm⁻¹. The excellent coefficient of determination (R²) was achieved (0.9992) with 0.01 mg standard error of calibration. This work clearly revealed the capability of the transmission FT-IR spectroscopy and extended its application for determining the exact quantity of roxithromycin to control the processing formulation and quality of finished product with the analysis time of less than 3 min using the neat solid samples.