Determination of aliphatic alcohols after on-line microwave-assisted derivatization by liquid chromatography-photodiode array detection

In this study, high-performance liquid chromatography (HPLC) in conjunction with continuous derivatization for the determination of aliphatic and polyethoxylated alcohol is reported. Reaction of alcohol group with phenyl isocyanate or benzyl chloride reagents assisted with microwaves (MW) irradiation is carried out in an on-line system coupled to HPLC with photodiode array detection (PDA). Reactor was placed into a microwave oven at 450 W. The flow rate, reagent amounts, irradiation time, and chromatographic conditions were optimized. The continuous analysis using the system MW-HPLC-PDA provided high sensitivity, reduce the amount of reagents and analysis time. This proposed method can be used for the analysis of commercial alcohol polyethoxylated mixture.     

Sequential injection analysis system for on-line monitoring of l-cysteine concentration in biological processes

A sequential injection analysis (SIA) system was developed to monitor the concentration of l-cysteine in biological processes on-line. It is based on the redox reaction of l-cysteine with iron(III) in the presence of 1,10-phenanthroline (phen) and the detection of the red-iron(II)-phen complex with a spectrophotometry. The system was fully automated using software written in the LabVIEW™ development environment. A number of system variables such as the flow rate of the carrier buffer solution, the volume ratio of the sample to the reagents, and the reaction coil length, etc., were evaluated to increase the sensitivity and performance of the SIA system. Under partially optimized operating conditions the performance of the SIA system was linear up to a concentration of l-cysteine of 1 mM (R² = 0.998) with a detection limit of 0.005 mM and a sample frequency of 15 hr⁻¹. The SIA system was employed to monitor the concentration of l-cysteine on-line in a continuously stirred reactor and a fermentation process of Saccharomyces cerevisiae. The on-line monitored data were in good agreement with the off-line data measured by a HPLC with a fluorescence detector (n = 15, R² = 09899).     

Determination of thiomersal by flow injection coupled with microwave-assisted photochemical online oxidative decomposition of organic mercury and cold vapor atomic fluorescence spectroscopy

We developed a flow injection (FI) method for the determination of thiomersal (sodium ethylmercurithiosalicylate, C₉H₉HgNaO₂S) based on the UV/microwave (MW) photochemical, online oxidation of organic mercury, followed by cold vapor generation atomic fluorescence spectrometry (CVG-AFS) detection. Thiomersal was quantitatively converted in the MW/UV process to Hg(II), with a yield of 97 ± 3%. This reaction was followed by the reduction of Hg(II) to Hg(0) performed in a knotted reaction coil with NaBH₄ solution, and AFS detection in an Ar/H₂ miniaturized flame. The method was linear in the 0.01–2 μg mL⁻¹ range, with a LOD of 0.003 μg mL⁻¹. This method has been applied to the determination of thiomersal in ophthalmic solutions, with recoveries ranging between 97% and 101%. We found a mercury concentration in commercial ophthalmic solutions ranging between 7.5 and 59.0 μg mL⁻¹.     

Development of a flow system for the determination of cadmium in fuel alcohol using vermicompost as biosorbent and flame atomic absorption spectrometry

In this study a method for the determination of cadmium in fuel alcohol using solid-phase extraction with a flow injection analysis system and detection by flame atomic absorption spectrometry was developed. The sorbent material used was a vermicompost commonly used as a garden fertilizer. The chemical and flow variables of the on-line preconcentration system were optimized by means of a full factorial design. The selected factors were: sorbent mass, sample pH, buffer concentration and sample flow rate. The optimum extraction conditions were obtained using sample pH in the range of 7.3-8.3 buffered with tris(hydroxymethyl)aminomethane at 50 mmol L⁻¹, a sample flow rate of 4.5 mL min⁻¹ and 160 mg of sorbent mass. With the optimized conditions, the preconcentration factor, limit of detection and sample throughput were estimated as 32 (for preconcentration of 10 mL sample), 1.7 μg L⁻¹ and 20 samples per hour, respectively. The analytical curve was linear from 5 up to at least 50 μg L⁻¹, with a correlation coefficient of 0.998 and a relative standard deviation of 2.4% (35 μg L⁻¹, n = 7). The developed method was successfully applied to spiked fuel alcohol, and accuracy was assessed through recovery tests, with recovery ranging from 94% to 100%.     

Determination of cadmium in alcohol fuel using Moringa oleifera seeds as a biosorbent in an on-line system coupled to FAAS

In this study a new method for determination of cadmium in alcohol fuel using Moringa oleifera seeds as a biosorbent in an on-line preconcentration system coupled to flame atomic absorption spectrometry (FAAS) was developed. Flow and chemical variables of the proposed system were optimized through multivariate designs. The limit of detection for cadmium was 5.50 μg L⁻¹ and the precision was below 2.3% (35.0 μg L⁻¹, n = 9). The analytical curve was linear from 5 to 150 μg L⁻¹, with a correlation coefficient of 0.9993. The developed method was successfully applied to spiked alcohol fuel, and accuracy was assessed through recovery tests, with recovery ranging from 97.50 to 100%.     

The determination of organochlorine pesticides based on dynamic microwave-assisted extraction coupled with on-line solid-phase extraction of high-performance liquid chromatography

A rapid technique based on dynamic microwave-assisted extraction coupled with on-line solid-phase extraction of high-performance liquid chromatography (DMAE-SPE-HPLC) has been developed. A TM₀₁₀ microwave resonance cavity built in the laboratory was applied to concentrate the microwave energy. The sample placed in the zone of microwave irradiation was extracted with 95% acetonitrile (ACN) aqueous solution which was driven by a peristaltic pump at a flow rate of 1.0 mL min⁻¹. The extraction can be completed in a recirculating system in 10 min. When a number of extraction cycles were completed, the extract (1 mL) was diluted on-line with water. Then the extract was loaded into an SPE column where the analytes were retained while the unretained matrix components were washed away. Subsequently, the analytes were automatically transferred from the SPE column to the analytical column and determined by UV detector at 238 nm. The technique was used for determination of organochlorine pesticides (OCPs) in grains, including wheat, rice, corn and bean. The limits of detection of OCPs are in the range of 19-37 ng g⁻¹. The recoveries obtained by analyzing the four spiked grain samples are in the range of 86-105%, whereas the relative standard deviation (R.S.D.) values are <8.7% ranging from 1.2 to 8.7%. Our method was demonstrated to be fast, accurate, and precise. In addition, only small quantities of solvent and sample were required.     

Continuous determination of total flavonoids in Platycladus orientalis (L.) Franco by dynamic microwave-assisted extraction coupled with on-line derivatization and ultraviolet-visible detection

This paper describes a new method for the determination of total flavonoids in Platycladus orientalis (L.) Franco. The method was based on dynamic microwave-assisted extraction (DMAE) coupled with on-line derivatization and ultraviolet-visible (UV-vis) detection. The influence of the experimental conditions was tested. Maximum extraction yield was achieved using 80% aqueous methanol of extraction solvent; 80 W of microwave output power; 5 min of extraction time; 1.0 mL min⁻¹ of extraction solvent flow rate. The derivatization reaction between aluminium chloride and flavonoid is one of the most sensitive and selective reactions for total flavonoids determination. The optimized derivatization conditions are as follows: derivatization reagent 1.5% aluminium chloride methanol solution; reaction coil length 100 cm; derivatization reagent flow rate 1.5 mL min⁻¹. The detection and quantification limits obtained are 0.28 and 0.92 mg g⁻¹, respectively. The intra-day and inter-day precisions (R.S.D.) obtained are 1.5% and 4.6%, respectively. Mean recovery is 98.5%. This method was successfully applied to the determination of total flavonoids in P. orientalis (L.) Franco and compared with heat reflux extraction. The results showed that the higher extraction yield of total flavonoids was obtained by DMAE with shorter extraction time (5 min) and small quantity of extraction solvent (5 mL).     

Hydrolysis of chitosan under microwave irradiation in ionic liquids promoted by sulfonic acid-functionalized ionic liquids

Hydrolysis of chitosan in ionic liquids was carried out under microwave irradiation (MW) using sulfonic acid-functionalized ionic liquids (SFILs) as catalysts. The effect of microwave power, irradiation time, dosage of SFILs and DMSO was investigated by orthogonal tests. Under the optimal reaction conditions, the yield of total reducing sugars (TRS) reached over 90% within 2 min. The viscosity-average molecular weight of degraded chitosan was determined by viscosity method. The structures of the original and degraded chitosan were characterized by Fourier-transform infrared (FTIR) spectra, X-ray powder diffraction (XRD) analysis and carbon-13 nuclear magnetic resonance spectroscopy (¹³C NMR). The influence of microwave power and irradiation time on the TRS and M_v was further studied. This method can dramatically reduce reaction time.     

Microwave-assisted on-line derivatization for sensitive flow injection fluorometric determination of formaldehyde in some foods

A rapid and sensitive flow injection fluorometry has been developed for the determination of formaldehyde based on the microwave on-line accelerating its Hantzsch reaction with cyclohexane-1,3-dione. Under the optimized conditions, the fluorescent intensity is proportional to formaldehyde content in the range from 0.05 ng/mL to 2.000 μg/mL. The detection limit (S/N = 3) is 0.02 ng/mL and the analytical frequency is 28 injections per hour. The relative standard deviations are 2.2% and 3.1% for eleven injections of 0.100 and 0.001 μg/mL of formaldehyde, respectively. With the assistance of microwave irradiation, a best sensitive fluorometry was established for the determination of formaldehyde at a high analytical frequency. This method was successfully applied to food analysis without requiring any sample pretreatment, and the determination results were correlated well with those obtained by the standard method with a sample pretreatment of steam distillation.     

Rapid on-line sample dissolution assisted by focused microwave radiation for silicate analysis employing flame atomic absorption spectrometry: iron determination

An on-line automated flow injection system with microwave-assisted sample digestion was used to perform silicate rock dissolution in acid medium for iron determination. For this purpose, a continuous flow system was built up by using an automatic flow injection analysis (FIA) system coupled to a flame atomic absorption spectrometer (FAAS), including a focused microwave oven unit. Inside the microwave cavity was inserted a polytetrafluoroethylene (PTFE) reactor coil (300 cm length and 0.8 mm i.d.) where the dissolution takes place. Chemical and flow variables as well as iron determination parameters were studied. In the flow system, a slurry of the rock sample (50 mg in 200 ml of acid mixture HF+HCl+HNO₃) is pumped through the reaction coil and the microwaves are turned on. After elapsed the time required to complete the sample dissolution, the mixture is pumped again in order to fill the sampling loop (500 μl). Then, by changing the valve position, a water carrier stream pushes the sample solution through the flame atomic absorption spectrometer nebulizer. To achieve an accurate determination of the rock certified materials, the slurry sample was irradiated during 210 s at 90 W power. Working in that condition, a detection limit of 0.80 μg ml⁻¹ (which corresponds to an Fe₂O₃ content of 0.46%) and an analytical throughput of 10 h⁻¹ were achieved. The relative standard deviation (R.S.D.) of the method varied between 1 and 11% when applied to the rock certified materials.     

Inorganic arsenic speciation analysis of water samples by trapping arsine on tungsten coil for atomic fluorescence spectrometric determination

Arsine trapping on resistively heated tungsten coil was investigated and an analytical method for ultratrace arsenic determination in environmental samples was established. Several chemical modifiers, including Re, Pt, Mo, Ta and Rh, were explored as permanent chemical modifiers for tungsten coil on-line trapping and Rh gave the best performance. Arsine was on-line trapped on Rh-coated tungsten coil at 640 °C, then released at 1930 °C and subsequently delivered to an atomic fluorescence spectrometer (AFS) by a mixture of Ar and H₂ for measurement. In the medium of 2% (v/v) HCl and 3% (m/v) KBH₄, arsine can be selectively generated from As(III). Total inorganic arsenic was determined after pre-reduction of As(V) to As(III) in 0.5% (m/v) thiourea-0.5% (m/v) ascorbic acid solution. The concentration of As(V) was calculated by difference between the total inorganic arsenic and As(III), and inorganic arsenic speciation was thus achieved. With 8 min on-line trapping, the limit of detection was 10 ng L⁻¹ for As(III) and 9 ng L⁻¹ for total As; and the precision was found to be <5% R.S.D. (n = 7) for 0.2 ng mL⁻¹ As. The proposed method was successfully applied in total arsenic determination of several standard reference materials and inorganic arsenic speciation analysis of nature water samples.     

Dechlorination of poly(vinyl chloride) by microwave irradiation I: A simple examination using a commercial microwave oven

Poly(vinyl chloride) (PVC) was decomposed by microwave (MW) irradiation (2.45 GHz) using a commercial MW oven. The efficiency of dielectric absorption was evaluated quantitatively from the rate of temperature increase on MW irradiation. The efficiency of dielectric heating increased at temperatures above the glass transition temperature (T_g). The decomposition on MW irradiation, monitored using the weight, depended on the initial (preheating) temperature of the sample before irradiation. The degradation time profile with various initial temperatures was shifted along the time axis and was successfully superimposed on a single curve. A pure PVC film was subjected to heating at a constant temperature from 230 °C to 310 °C, and the rate of weight decrease on heating was measured. The apparent activation energy was 84.4 kJ/mol for a single monomer unit.     

Automated on-line microdialysis sampling coupled with high-performance liquid chromatography for simultaneous determination of malondialdehyde and ofloxacin in whole blood

We have developed a system that couples an on-line microdialysis (MD) system with flow injection high-performance liquid chromatography (HPLC)-fluorescence detection for simultaneous measurement of the concentrations of malondialdehyde (MDA) and ofloxacin (OFL) in whole blood samples. The sample matrix was first cleaned with an MD system using an MD probe. A continuously flowing dialysate stream was derivatized on-line and auto-injected into a separation column. MDA and OFL were separated through a reverse-phase C18 column (250 mm × 4.6 mm) at a flow rate of 0.8 mL min⁻¹ and then detected using a fluorescence detector (excitation: 532 nm; emission: 553 nm); the system's components were connected on-line using a valve control. Validation experiments demonstrated good linearity, precision, accuracy, and recovery. The precisions for the determinations of MDA and OFL, measured in terms of relative standard deviations, were 6.5% and 4.6%, respectively, for intra-day assays and 7.5% and 8.7%, respectively, for inter-day assays. The average recoveries of MDA and OFL spiked in plasma were each close to 100%. The use of this on-line MD-HPLC system permitted continuous monitoring of MDA and OFL in OFL-treated whole blood subjected to UV-A irradiation. Based on our results, the UV-A irradiation markedly increased the level of MDA in the OFL-treated whole blood.     

One-pot and microwave-assisted synthesis of N-sulfonylaziridines

A novel and efficient microwave-assisted one-step reaction was developed to synthesize chiral N-sulfonylaziridines by the reaction of different chiral amino alcohols and sulfonic chlorides. The newly developed microwave synthetic method has the advantage of reducing the reaction time from 24 to 0.5 h with improved yields (84-93%) and minimizing by-products.     

Antimony speciation in soils: improving the detection limits using post-column pre-reduction hydride generation atomic fluorescence spectroscopy (HPLC/pre-reduction/HG-AFS)

HG-AFS is highly sensitive and low cost detection system and its use for antimony chemical speciation coupled to HPLC is gaining popularity. However speciation analysis in soils is strongly hampered because the most efficient extractant reported in the literature (oxalic acid) strongly inhibits the generation of SbH₃ by Sb(V), the major species in this kind of matrix, severely affecting its detection limits. The purpose of this research is to reduce the detection limit of Sb(V), by using a post column on-line reduction system with l-cysteine reagent (HPLC/pre-reduction/HG-AFS). The system was optimized by experimental design, optimum conditions found were 2% (w/v) and 10 °C temperature coil. Detection limits of Sb(V) and Sb(III) in oxalic acid (0.25 mol L⁻¹) were improved from 0.3 and 0.1 μg L⁻¹ to 0.07 and 0.07 μg L⁻¹, respectively. The methodology developed was applied to Chilean soils, where Sb(V) was the predominant species.     

Flow injection wetting-film extraction system for flame atomic absorption spectrometric determination of cadmium in environmental waters

A newly simple flow injection wetting-film extraction system coupled to flame atomic absorption spectrometry (FAAS) has been developed for trace amount of cadmium determination. The sample was mixed on-line with sodium diethyl dithiocarbamate and the produced non-charged Cd(II)-diethyl dithiocarbamate (DDTC) chelate complex was extracted on the thin film of diisobutyl ketone (DIBK) on the inner wall of the PTFE extraction coil. The wetting-film with the extracted analyte was then eluted by a segment of the cover solvent, and transported directly to the FAAS for evaluation. All the important chemical and flow parameters were optimized. Under the optimized conditions an enhancement factor of 35, a sample frequency of 22 h⁻¹ and a detection limit of c_L = 0.7 μg l⁻¹ Cd(II) were obtained for 60 s preconcentration time. The calibration curve was linear over the concentration range 1.5-45.0 μg l⁻¹ Cd(II) and the relative standard deviation, R.S.D. (n = 10) was 3.9%, at 10.0 μg l⁻¹ concentration level. The developed method was successfully applied to cadmium determination in a variety of environmental water samples as well as waste-water sample.     

Preparation and characterization of fluorinated acrylate copolymer latexes by miniemulsion polymerization under microwave irradiation

Fluoroacrylate copolymer miniemulsion was prepared by miniemulsion polymerization under microwave irradiation. The composition of the copolymer was determined by FTIR, DSC, ¹H NMR and ¹⁹F NMR. The morphology, size, and size distribution of the latex particles as well as changes in the size during polymerization were characterized by TEM and photon correlation spectroscopy (PCS). The effects of kinetic parameters on the polymerization were evaluated. The particle size of latex underwent almost no change during microwave irradiation polymerization. The diameters of latex particles prepared by microwave irradiation were smaller and more monodispersed than those prepared by conventional heating and the latex had good centrifugal stability. Polymerization under microwave irradiation had a higher reaction rate and higher conversion than traditional heating. By using 10 wt% fluoromonomer, the surface energy of the latex film could be reduced from 27.24 mJ/m² (latex film of fluorine-free) to 17.59 mJ/m² and the decomposition temperature increased by 25 °C.     

Hybrid sequential injection-flow injection manifold for the spectrophotometric determination of total sulfite in wines using o-phthalaldehyde and gas-diffusion

A new automated spectrophotometric method for the determination of total sulfite in white and red wines is reported. The assay is based on the reaction of o-phthalaldehyde (OPA) and ammonium chloride with the analyte in basic medium under SI conditions. Upon on-line alkalization with NaOH, a blue product is formed having an absorption maximum at 630 nm. The parameters affecting the reaction - temperature, pH, ionic strength, amount concentration and volume of OPA, amount concentration of ammonium chloride, flow rate and reaction coil length - and the gas-diffusion process - sample and HCl volumes, length of mixing coil, donor flow rate - were studied. The proposed method was validated in terms of linearity (1-40 mg L⁻¹, r = 0.9997), limit of detection (c_L = 0.3 mg L⁻¹) and quantitation (c_Q = 1.0 mg L⁻¹), precision (s_r = 2.2% at 20 mg L⁻¹ sulfite, n = 12) and selectivity. The applicability of the analytical procedure was evaluated by analyzing white and red wine samples, while the accuracy as expressed by recovery experiments ranged between 96% and 106%.     

Flow-injection catalytic spectrophotometic determination of molybdenum(VI) in plants using bromate oxidative coupling of p-hydrazinobensenesulfonic acid with N-(1-naphthyl)ethylenediamine

A novel flow-injection spectrophotometry has been developed for the determination of molybdenum(VI) at nanograms per milliliter levels. The method is based on the catalytic effect of molybdenum(VI) on the bromate oxidative coupling of p-hydrazinobenzenesulfonic acid with N-(1-naphthyl)ethylenediamine to form an azo dye (λ_max = 530 nm). Chromotropic acid (4,5-dihydroxy-2,7-naphthalenedisulfonic acid) acted as an effective activator for the molybdenum(VI)-catalyzed reaction and increased the sensitivity of the method. The reaction was monitored by measuring the change in absorbance of the dye produced. The proposed method allowed the determination of molybdenum(VI) in the range 1.0-20 ng mL⁻¹ with sample throughput of 15 h⁻¹. The limit of detection was 0.5 ng mL⁻¹ and a relative standard deviation for 10 ng mL⁻¹ molybdenum(VI) (n = 10) was 2.5%. The interfering ions were eliminated by using the combination of a masking agent and on-line minicolumn packed with cation exchanger. The present method was successfully applied to the determination of molybdenum(VI) in plant foodstuffs.     

Improvement of an enzyme electrode by poly(vinyl alcohol) coating for amperometric measurement of phenol

A poly(vinyl alcohol) film cross-linked with glutaraldehyde (PVA-GA) was introduced to the surface of a tyrosinase-based carbon paste electrode. The coated PVA-GA film was beneficial in terms of increasing the stability and reproducibility of the enzyme electrode. The electrode showed a sensitive current response to the reduction of the o-quinone, which was the oxidation product of phenol, by the tyrosinase, in the presence of oxygen. The effects of the PVA and PVA-GA coating, the pH, and the GA:PVA ratio on the current response were investigated. The sensitivity of the PVA-GA-Tyr electrode was 130.56 μA/mM (1.8 μA/μM cm²) and the linear range of phenol was 0.5-100 μM. At a higher concentration of phenol (>100 μM), the current response showed the Michaelis-Menten behavior. Using the PVA-GA-Tyr electrode, a two-electrode system was tested as a prototype sensor for portable applications.