Flow-injection investigation of the chemiluminescent reaction of bis(2,4,6-(trichlorophenyl)oxalate) with free chlorine

This work investigated the chemiluminescent reaction of free chlorine with bis(2,4,6-(trichlorophenyl)oxalate) (TCPO) in the presence of 9,10-diphenylanthracene in acetonitrile/water medium, with analytical application for free chlorine in tap water. In the absence of free chlorine, the background signal increased with the pH and the chemiluminescence emission showed strong dependence with the sample acidity. A flow injection analysis system, for free chlorine determination, was developed. The linear range for free chlorine was (0.2-3.0)×10⁻⁵ mol l⁻¹. Chloramine 1.0×10⁻⁵ mol l⁻¹ and chlorite 1.0×10⁻⁶ mol l⁻¹ also enhanced the chemiluminescence intensity.     

A new sensitive and selective fluorescence method for determination of chlorine dioxide in water using rhodamine S

A new simple, selective and sensitive method for the determination of trace chlorine dioxide in water has been developed, based on the oxidation by chlorine dioxide to reduction the fluorescence of rhodamine dyes in ammonia-ammonium chloride buffer solution. Four rhodamine dyes systems such as rhodamine S, rhodamine G, rhodamine B and butyl-rhodamine B were tested. The rhodamine S system is the best, with a linear range of 0.0060-0.450 μg mL⁻¹ and a detection limit of 0.0030 μg mL⁻¹ ClO₂. It was applied to the determination of chlorine dioxide in synthetic samples and real samples, with satisfactory results. This method has good selectivity, especially, other chlorine species such as chlorine, hypochlorite, chlorite and chlorate do not interfere the determination. The mechanism of fluorescence reduction was also considered.     

Reversed flow injection spectrophotometric determination of chlorate

An interfacing has been developed to connect a spectrophotometer with a personal computer and used as a readout system for development of a simple, rapid and sensitive reversed flow injection (rFI) procedure for chlorate determination. The method is based on the oxidation of indigo carmine by chlorate ions in an acidic solution (dil. HCl) leading to the decrease in absorbance at 610 nm. The decrease in absorbance is directly related to the chlorate concentration present in the sample solutions. Optimum conditions for chlorate were examined. A linear calibration graph over the range of 0.1-0.5 mg L⁻¹ chlorate was established with the regression equation of Y = 104.5X + 1.0, r² = 0.9961 (n = 6). The detection limit (3σ) of 0.03 mg L⁻¹, the limit of quantitation (10σ) of 0.10 mg L⁻¹ and the RSD of 3.2% for 0.3 mg L⁻¹ chlorate (n = 11) together with a sample throughput of 92 h⁻¹ were obtained. The recovery of the added chlorate in spiked water samples was 98.5 ± 3.1%. Major interferences for chlorate determination were found to be BrO₃⁻, ClO₂⁻, ClO⁻ and IO₃⁻ which were overcome by using SO₃²⁻ (as Na₂SO₃) as masking agent. The method has been successfully applied for the determination of chlorate in spiked water samples with the minimum reagent consumption of 14.0 mL h⁻¹. Good agreement between the proposed rFIA and the reference methods was found verified by Student's t-test at 95% confidence level.     

Determination of picloram in natural waters employing sequential injection square wave voltammetry using the hanging mercury drop electrode

This paper describes the development of a sequential injection analysis method to automate the determination of picloram by square wave voltammetry exploiting the concept of monosegmented flow analysis to perform in-line sample conditioning and standard addition. To perform these tasks, an 800 μL monosegment is formed, composed by 400 μL of sample and 400 μL of conditioning/standard solution, in medium of 0.10 mol L⁻¹ H₂SO₄. Homogenization of the monosegment is achieved by three flow reversals. After homogenization the mixture zone is injected toward the flow cell, which is adapted to the capillary of a hanging drop mercury electrode, at a flow rate of 50 μL s⁻¹. After a suitable delay time, the potential is scanned from −0.5 to −1.0 V versus Ag/AgCl at frequency of 300 Hz and pulse height of 25 mV. The linear dynamic range is observed for picloram concentrations between 0.10 and 2.50 mg L⁻¹ fitting to the linear equation I_p = (−2.19 ± 0.03)C_picloram + (0.096 ± 0.039), with R² = 0.9996, for which the slope is given in μA L mg⁻¹. The detection and quantification limits are 0.036 and 0.12 mg L⁻¹, respectively. The sampling frequency is 37 h⁻¹ when the standard addition protocol is followed, but can be increased to 41 h⁻¹ if the protocol to obtain in-line external calibration curve is used for quantification. The method was applied for determination of picloram in spiked water samples and the accuracy was evaluated by comparison with high performance liquid chromatography using molecular absorption at 220 nm for detection. No evidences of statistically significant differences between the two methods were observed.     

Interfacing on-line solid phase extraction with monolithic column multisyringe chromatography and chemiluminescence detection: An effective tool for fast, sensitive and selective determination of thiazide diuretics

A new, multisyringe flow injection set-up has been developed for the completely automated determination of trace thiazide compounds with diuretic action in different types of samples. The proposed instrumental set-up exploits for the first time, a low pressure on-line solid phase extraction-liquid chromatography-chemiluminescence detection method. This novel combination of sample treatments in flow systems expands the current applicability of low pressure liquid chromatography due to the isolation/preconcentration of the target compounds, besides high selectivity and sensitivity.For the determination of three thiazide compounds named hydroflumethiazide, furosemide and bendroflumethiazide, the proposed set-up provided with the preconcentration of only 1 mL of sample, limits of detection of 3, 60 and 40 μg L⁻¹, respectively. Furthermore wide linear dynamic ranges of 6-4000, 140-20,000 and 90-40,000 μg L⁻¹, respectively, were obtained. Besides of this, a high injection throughput of 12 h⁻¹ was also achieved. As in sports, thiazide diuretics are prohibited substances, the proposed method has been applied to their determination in urine samples. Furthermore the potential of the proposed method as a fast-screening approach for emerging contaminants in waters has been also tested by applying it to well water and leachates from a solid waste landfill.     

Determination of nitrogen in hydrolyzed protein formulations by continuous vapour phase FTIR

An on-line system with vapour generation (VG) and Fourier transform infrared (FTIR) spectrometric detection has been developed for the determination of free ammonium and organic nitrogen in agrochemical formulations containing hydrolyzed proteins. Commercial samples were digested, in batch mode, with sulphuric acid and the obtained solution was alkalinized on-line to transform the NH₄⁺ to NH₃ that was continuously monitored by FTIR. Free ammonium was determined in the same system after simple dilution of undigested samples with water. Different gas phase separators were assayed in order to introduce gaseous NH₃ into a home made IR gas cell of 10 cm pathlength, where the corresponding FTIR spectra were acquired by accumulating 10 scans per spectrum. The 967.0 cm⁻¹ band was used for the quantification of ammonia. The figures of merit of the proposed method involve a linear range up to 100 mg L⁻¹, a limit of detection (3σ) of 1.4 mg L⁻¹ of N, a limit of quantification (10σ) of 4.8 mg L⁻¹ of N, a precision (R.S.D.) of 3.0% for 10 replicate determinations of a 10.0 mg L⁻¹ of N and a sample measurement frequency of 60 h⁻¹. The method was successfully applied to the determination of free ammonium and total N in commercial amino acid formulations and results compare well with those obtained by the Kjeldhal method.     

Simultaneous determination of pH, chloride and nickel in electroplating baths using sequential injection analysis

A sequential injection analysis system was developed to quantify pH, chloride and nickel in electrolytic baths, in the ranges 1-5 pH units, and 0.1-1.0 and 0.1-1.6 mol l⁻¹, respectively. To enable pH and chloride determination, potentiometric detection with two ion-selective electrodes in a tubular configuration was used. Nickel concentrations were assessed using colorimetric detection at 660 nm. pH was determined prior to nickel determination and just after sample injection (500 μl) into a 0.025 mol l⁻¹ phosphate buffer carrier stream at pH 6.3 and a 9.10 ml min⁻¹ flow rate. For chloride determination, on-line dialysis through a cellulose membrane was used to enable sample dilution and matrix separation. A 2⁵⁻¹ fractional factorial design based on the carrier solution composition and the levels of the hydrodynamic parameters was used for system optimization. At the optimized settings a sampling rate of 40 samples h⁻¹ was attained, with precision and accuracy statistically indistinguishable from those achieved with conventional procedures.     

Flow injection conductometric system with gas diffusion separation for the determination of Kjeldahl nitrogen in milk and chicken meat

A simple flow injection (FI) conductometric system with gas diffusion separation was developed for the determination of Kjeldahl nitrogen (or proteins) in milk and chicken meat. The sample was digested according to the Kjeldahl standard method and the digest was diluted and directly injected into the donor stream consisting of 4 M NaOH. In alkaline medium, ammonium was converted to ammonia, which diffused through the PTFE membrane to dissolve in an acceptor stream (water). Dissociation of ammonia caused a change in conductance of the acceptor solution, which was linearly proportional to the concentration of ammonium originally present in the injected solution. A conductometric flow through cell and an amplifier circuit was fabricated, which helped improve sensitivity of the conductometric detection system. With using a plumbing Teflon tape as a gas diffusion membrane and without thermostating control of the system, a linear calibration graph in range of 10-100 mg L⁻¹ N-NH₄ was obtained, with detection limit of 1 mg L⁻¹ and good precision (relative standard deviation of 0.3% for 11 replicate injections of 50 mg L⁻¹ N-NH₄). The developed method was validated by the standard Kjeldahl distillation/titration method for the analysis of milk and chicken meat samples. The proposed system had sample throughput of 35 h⁻¹ and consumed much smaller amounts of chemical than the standard method (275 mg vs 17.5 g of NaOH per analysis, respectively).     

Three-dimensional printed sample load/inject valves enabling online monitoring of extracellular calcium and zinc ions in living rat brains

We have developed a simple and low-cost flow injection system coupled to a quadruple ICP-MS for the direct and continuous determination of multi-element in microdialysates. To interface microdialysis sampling to an inductively coupled plasma mass spectrometer (ICP-MS), we employed 3D printing to manufacture an as-designed sample load/inject valve featuring an in-valve sample loop for precise handling of microliter samples with a dissolved solids content of 0.9% NaCl (w/v). To demonstrate the practicality of our developed on-line system, we applied the 3D printed valve equipped a 5-μL sample loop to minimize the occurrence of salt matrix effects and facilitate an online dynamic monitoring of extracellular calcium and zinc ions in living rat brains. Under the practical condition (temporal resolution: 10 h⁻¹), dynamic profiling of these two metal ions in living rat brain extracellular fluid after probe implantation (the basal values for Ca and Zn were 12.11 ± 0.10 mg L⁻¹ and 1.87 ± 0.05 μg L⁻¹, respectively) and real-time monitoring of the physiological response to excitotoxic stress elicited upon perfusing a solution of 2.5 mM N-methyl-d-aspartate were performed.     

Time-based multisyringe flow injection system for the spectrofluorimetric determination of aluminium

A time-based multisyringe flow injection procedure with spectrofluorimetric detection is proposed in this paper for the determination of aluminium in drinking water. The flow methodology is based on the simultaneous or sequential injection of sample and chelating reagent (viz. 8-hydroxyquinoline-5-sulphonic acid) plugs using a multicommutation approach so that three successive injections may be performed with a sole displacement of the piston driver bar of the burette. Thus, an injection throughput as high as 154 h⁻¹ is achieved by sampling a 182 μl sample zone. In order to enhance the luminescence, the reaction is carried out in micellar medium using hexadecyltrimethylammonium chloride as surfactant. The influence of geometric and hydrodynamic variables as well as several parameters such as multicommutation timing, ligand and surfactant concentration and reagent pH was assessed.Under the selected working conditions, a linear dynamic range from 10 to 500 μg l⁻¹ Al(III), a 3σ detection limit of 0.5 μg l⁻¹ and a coefficient of variation of 0.6% at the 30 μg l⁻¹ level were obtained. The analytical features were compared with those reported in previous flow injection and sequential injection methods. The multisyringe technique was successfully applied to the determination of aluminium in drinking water at low mineralisation levels, validating the results by inductively coupled plasma atomic emission spectrometry.     

Simultaneous determination of some food additives in soft drinks and other liquid foods by flow injection on-line dialysis coupled to high performance liquid chromatography

Flow injection on-line dialysis was developed for sample pretreatment prior to the simultaneous determination of some food additives by high performance liquid chromatography (FID-HPLC). A liquid sample or mixed standard solution (900 μL) was injected into a donor stream (5%, w/v, sucrose) of FID system and was pushed further through a dialysis cell, while an acceptor solution (0.025 mol L⁻¹ phosphate buffer, pH 3.75) was held in the opposite side of the dialysis membrane. The dialysate was then flowed to an injection loop of the HPLC valve, where it was further injected into the HPLC system and analyzed under isocratic reverse-phase HPLC conditions and UV detection (230 nm). The order of elution of five food additives was acesulfame-K, saccharin, caffeine, benzoic acid and sorbic acid, respectively, with the analysis time of 14 min. On-line dialysis and HPLC analysis could be performed in parallel, providing sample throughput of 4.3 h⁻¹. Dialysis efficiencies of five food additives were in ranges of 5-11%. Linear calibration graphs were in ranges of 10-100 mg L⁻¹ for acesulfame-K and saccharin, 10-250 mg L⁻¹ for benzoic acid and 10-500 mg L⁻¹ for caffeine and sorbic acid. Good precisions (RSD < 5%) for all the additives were obtained. The proposed system was applied to soft drink and other liquid food samples. Acceptable percentage recoveries could be obtained by appropriate dilution of the sample before injecting into the system. The developed system has advantages of high degrees of automation for sample pretreatment, i.e., on-line sample separation and dilution and low consumption of chemicals and materials.     

Developing a sequential injection-square wave voltammetry (SI-SWV) method for determination of atrazine using a hanging mercury drop electrode

This paper describes the development of a sequential injection analysis method to automate the determination of atrazine by square wave voltammetry exploiting the concept of monosegmented flow analysis to perform in-line sample conditioning and standard addition. To perform these tasks, an 800 μL monosegment is formed, composed by 400 μL of sample and 400 μL of buffer/standard solution. To obtain an efficient homogenization, the sample solution is divided in five zones intercalated by four zones of the Britton-Robinson buffer (pH 2.0) in presence of appropriate concentration of NaNO₃ and varying atrazine standard concentrations. This mixture zone is isolated from the carrier solution by two 100 μL air bubbles. After homogenization in an auxiliary reaction coil the mixture zone is injected toward the flow cell, which is adapted to the capillary of a hanging drop mercury electrode, at a flow rate of 50 μL s⁻¹. After a suitable delay time, the potential is scanned from −0.5 to −1.2 V versus Ag/AgCl using a frequency of 300 Hz and pulse height of 25 mV. The linear dynamic range is observed for atrazine concentrations between 1.16 × 10⁻⁷ and 2.32 × 10⁻⁶ mol L⁻¹, obeying the linear equation i_p = (−6.91 ± 0.07) × 10⁸[atrazine] + (4 ± 8), with r² = 0.9996, for which the slope is given in nA L mol⁻¹. The detection and quantification limits of the method are 2.1 × 10⁻⁸ and 7.0 × 10⁻⁸ mol L⁻¹, respectively. The sampling frequency is 37 h⁻¹, when the standard addition protocol is followed. This frequency can be increased to 42 h⁻¹ if the protocol to obtain in-line calibration curve is used for quantification. The method was applied for determination of atrazine in spiked river water samples and its accuracy was evaluated by comparison with the batch standard addition approach, which revealed that there is no evidence of statistically significant differences between the two methods.     

A sequential injection system for indirect spectrophotometric determination of lactic acid in yogurt and fermented mash samples

A suitable non-enzymatic method is presented as an alternative to the lactic acid determination in yogurt and fermented mash samples. The oxidative conversion of lactic acid by Ce⁴⁺ to CO₂ was performed in a sequential injection system with a heating coil set at 45 °C. A gas diffusion unit was coupled to the flow system for promoting the permeation of CO₂, which was collected into a bromothymol blue solution (pH 8.4), used as indicator solution for the spectrophotometric determination (619 nm). Simplicity in operation, low reagent consumption, low cost and ruggedness are some remarkable characteristics of the proposed system. Base line drift was < 0.005 h^− 1. A linear range from 20.0 to 100.0 mg L^− 1 lactic acid was obtained (r² = 0.998), and the detection and quantification limits were estimated as 0.158 mg L^− 1 and 1.6 mg L^− 1, respectively. The sampling rate was 22 h^− 1, with a consumption of 0.04 g Ce⁴⁺ per determination. Interferences of matrix components were not detected. Samples of yogurt and sugar cane fermented mash products were analyzed, and no significant difference at 95% confidence level was observed when comparing the proposed method with HPLC analysis.     

Implementation of acoustic, radiofrequency and microwave rotating fields in analytical plasma sources

Four helium plasma sources operating at atmospheric pressure have been developed for analytical emission spectrometry by applying a synchronically rotating field with three or more phases operating at 1 kHz, 27 MHz or 2.45 GHz. The plasma takes the form of a disk and has minimum field strength at the axis. Thus, a channel is formed at the center through which the sample in the form of wet aerosol or a chemically generated vapor of halogen may be introduced. A dual-flow concentric ceramic injector was used to supply helium plasma gas and the sample to the plasma. The helium plasma operated at low power levels (40-300 W) and low gas flow rates of below 3 L min^− 1 and was self-igniting. The acoustic, radio-frequency (rf) and microwave-driven plasmas can withstand wet aerosol loadings of 5, 30 and 100 mg min^− 1, respectively, generated by an ultrasonic nebulizer without a desolvation unit. The plasma physical characteristics were compared at these three frequencies under otherwise similar operating conditions. The helium excitation temperature, OH rotational temperature and electron number density increased with increasing frequency in ranges of 2800-4000 K, 1100-3200 K and 0.1-7 × 10¹⁴ cm^− 3, respectively. To demonstrate the effect of frequency on the plasma excitation efficiency the emission intensity from halogen ions was evaluated using chemical vapor generation with continuous sampling without desiccation. Using 3-phase microwave, 6-phase microwave, 4-phase rf and 1 kHz helium plasma sources the detection limits (3σ) for chlorine at 479.40 nm were 26, 60, 230 and 1200 ng mL^− 1, respectively. The microwave-driven plasma was the densest and had the highest excitation potential toward chlorine and bromine ions.     

Sequential injection methodology for carbon speciation in bathing waters

A sequential injection method (SIA) for carbon speciation in inland bathing waters was developed comprising, in a single manifold, the determination of dissolved inorganic carbon (DIC), free dissolved carbon dioxide (CO₂), total carbon (TC), dissolved organic carbon and alkalinity. The determination of DIC, CO₂ and TC was based on colour change of bromothymol blue (660 nm) after CO₂ diffusion through a hydrophobic membrane placed in a gas diffusion unit (GDU). For the DIC determination, an in-line acidification prior to the GDU was performed and, for the TC determination, an in-line UV photo-oxidation of the sample prior to GDU ensured the conversion of all carbon forms into CO₂. Dissolved organic carbon (DOC) was determined by subtracting the obtained DIC value from the TC obtained value. The determination of alkalinity was based on the spectrophotometric measurement of bromocresol green colour change (611 nm) after reaction with acetic acid. The developed SIA method enabled the determination of DIC (0.24–3.5 mg C L⁻¹), CO₂ (1.0–10 mg C L⁻¹), TC (0.50–4.0 mg C L⁻¹) and alkalinity (1.2–4.7 mg C L⁻¹ and 4.7–19 mg C L⁻¹) with limits of detection of: 9.5 μg C L⁻¹, 20 μg C L⁻¹, 0.21 mg C L⁻¹, 0.32 mg C L⁻¹, respectively. The SIA system was effectively applied to inland bathing waters and the results showed good agreement with reference procedures.     

A tandem-flow assembly for the chemiluminometric determination of hydroquinone

A direct chemiluminescent procedure for determination of hydroquinone based on the emergent flow methodology known as multicommutation or tandem-flow is presented for first time. The manifold was based on a set of three channels and three solenoid valves; and, the determination was performed at 60 °C and at flow-rate of 7.5 ml min⁻¹. The complete cycle lasted 35 s, which resulted in a sample flow trough of 103 h⁻¹. The chemical process was the hydroquinone oxidation with the system sulphuric acid-potassium permanganate; and the light emission was clearly enhanced by the presence of quinine sulphate and benzalkonium chloride reaching a detection limit of 30 μg l⁻¹. The dynamic interval was over the range 0.1-15.0 mg l⁻¹ and a large list of interferents were assayed; the chemical robustness was also tested. The method was applied to different type of samples: namely, pharmaceutical formulations, a photographic solution and irrigation and residual superficial waters.     

Determination of carbon dioxide in gaseous samples by gas diffusion-flow injection

A gas diffusion-flow injection system was developed for the determination of carbon dioxide in gaseous samples. The calibration was based on the use of either gaseous carbon dioxide or aqueous sodium carbonate standards. Gaseous carbon dioxide samples and gaseous or aqueous standards were injected directly into a donor stream of 1.0×10⁻⁴ M H₂SO₄. In the gas diffusion unit, carbon dioxide diffused through a PTFE membrane into an acceptor stream containing a mixed acid/base indicator. The absorbance of the acceptor stream was monitored spectrophotometrically at 554 nm. The calibration plot was linear over the range of 5.00×10² to 1.27×10⁴ μl l⁻¹ with a sample throughput of 28 h⁻¹ and 3.2% R.S.D. ([CO₂]=2.37×10³ μl l⁻¹, n=12). The detection limit was determined as 2.50×10² μl l⁻¹. The flow system was successfully applied to the analysis of several natural gaseous samples and the headspace of milk containers during storage. The flow injection results were found to be statistically indistinguishable at the 95% confidence level from those obtained by gas chromatography using thermal conductivity detection.     

Optimization of dispersive liquid-liquid microextraction combined with gas chromatography for the analysis of nitroaromatic compounds in water

Dispersive liquid-liquid microextraction (DLLME) coupled with gas chromatography-flame ionization detector (GC-FID) was developed for preconcentration and determination of some nitroaromatic compounds in wastewater samples. The effects of different variables on the extraction efficiency were studied simultaneously using experimental design. The variables of interest in the DLLME process were extraction and disperser solvent volumes, salt effect, sample volume, extraction temperature and extraction time. A Plackett-Burman design was performed for screening of variables in order to determine the significant variables affecting the extraction efficiency. Then, the significant factors were optimized by using a central composite design (CCD) and the response surface equations were derived. The optimum experimental conditions found from this statistical evaluation included: sample volume, 9 mL; extraction solvent (CCl₄) volume, 20 μL; disperser solvent (methanol) volume, 0.75 mL; sodium chloride concentration, 3% (w/v); extraction temperature, 20 °C and extraction time, 2 min. Under the optimum conditions, the preconcentration factors were between 202 and 314. Limit of detections (LODs) ranged from 0.09 μg L⁻¹ (for 2-nitrotoluene) to 0.5 μg L⁻¹ (for 2,4-dinitrotoluene). Linear dynamic ranges (LDRs) of 0.5-300 and 1-400 μg L⁻¹ were obtained for mononitrotoluenes (MNTs) and dinitrotoluenes (DNTs), respectively. Performance of the present method was evaluated for extraction and determination of nitroaromatic compounds in wastewater samples in the range of microgram per liter and satisfactory results were obtained (RSDs < 10.1%).     

Selective fluorimetric method for the determination of histamine in seafood samples based on the concept of zone fluidics

In the present article we report our results on the development of a selective automated method for the determination of histamine in seafood using the concept of zone fluidics. The method is based on the sequential on-line reaction of the analyte with o-phthalaldehyde in the absence of a nucleophilic reagent, followed by acidification. The careful selection of the chemical and instrumental variables enabled the determination of the analyte with adequate sensitivity at the low micromolar level and with specificity against other biogenic amines and amino acids such as histidine. The LOD was 0.05 μmol L⁻¹ (0.6 mg kg⁻¹) and linearity was obeyed in the range of 0.5–15 μmol L⁻¹ (5.5–170 mg kg⁻¹). The proposed method offers a satisfactory sampling rate of 15 h⁻¹ and adequate accuracy and precision for the analysis of seafood products after minimum sample preparation and without employing a separation technique.     

Quality control of Metamitron in agrochemicals using Fourier transform infrared spectroscopy in the middle and near range

Two vibrational spectrometry-based methodologies were developed for Metamitron determination in pesticide formulations. Fourier transform-middle infrared (FT-MIR) procedure was based on the extraction of Metamitron by CHCl₃ and latter determination by peak area measurement between 1556 and 1533 cm⁻¹, corrected with a two points baseline established from 1572 to 1514 cm⁻¹. Fourier transform-near infrared (FT-NIR) determination was made after the extraction of Metamitron in acetonitrile and measuring the peak area between 6434 and 6394 cm⁻¹ corrected using a two points baseline defined between 6555 and 6228 cm⁻¹. Repeatability, as relative standard deviation, of 5 independent measurements at mg g⁻¹ concentration level, of 0.16% and 0.07% for MIR and NIR and a limit of detection of 0.03 and 0.004 mg g⁻¹ were obtained for MIR and NIR, respectively.NIR determination provides a sample frequency of 120 h⁻¹, higher than that found by MIR and liquid chromatographic methods (60 and 15 h⁻¹, respectively). On the other hand, the NIR method reduces the solvent consumption and waste generation, to only 1 ml acetonitrile per sample as compared with 3.4 ml chloroform required for the MIR determination and 60 ml acetonitrile used in the chromatographic reference procedure. So, vibrational procedures can be considered serious alternatives to long and time consuming chromatographic methods usually recommended for quality control of commercially available pesticide formulations.