A novel spectrophotometric method for batch and flow injection determination of cyanide in electroplating wastewater

A sensitive and highly selective spectrophotometric method is described for the determination of cyanide. It is based on a reaction of cyanide with aquacyanocobyrinic acid heptamethyl ester (ACCbs) reagent (orange color) at pH 9.5 to give dicyanocobester (DCCbs) (violet color). The increase of the absorption bands of the reaction product at 368 and 580 nm and the decrease of the reagent band at 353 nm are linearly proportional to the cyanide concentration. The method is used in static mode for determining cyanide over the concentration range 0.04-1.20 μg ml⁻¹ with a detection limit of 0.02 μg ml⁻¹ and for hydrodynamic analysis of 0.4-5.2 μg ml⁻¹ cyanide. Application for batch and flow injection monitoring of cyanide in electroplating wastewater samples gives results agree within ± 1.2% with those obtained by the standard potentiometry using the cyanide ion selective electrode. The method is practically free from interferences by PO₄³⁻, NO₃⁻, NO₂⁻, SO₄²⁻, F⁻, Cl⁻, Br⁻, I⁻, S²⁻ and SCN⁻ ions and gives results with average recoveries of 97.6-99.2%. Advantages offered by using ACCbs as a chromogen for cyanide assay are: (i) high selectivity and sensitivity of the coordination site of the reagent towards cyanide ion; (ii) fast reaction, since legation takes place at the axial position of the reagent; (iii) good solubility and stability of the reagent in aqueous solutions over a wide pH range; (iv) high stability of the reagent (ACCbs) and the colored complex product (DCCbs) and (v) possible absorbance measurements at three different wavelengths.     

Time-based multisyringe flow injection system for the spectrofluorimetric determination of aluminium

A time-based multisyringe flow injection procedure with spectrofluorimetric detection is proposed in this paper for the determination of aluminium in drinking water. The flow methodology is based on the simultaneous or sequential injection of sample and chelating reagent (viz. 8-hydroxyquinoline-5-sulphonic acid) plugs using a multicommutation approach so that three successive injections may be performed with a sole displacement of the piston driver bar of the burette. Thus, an injection throughput as high as 154 h⁻¹ is achieved by sampling a 182 μl sample zone. In order to enhance the luminescence, the reaction is carried out in micellar medium using hexadecyltrimethylammonium chloride as surfactant. The influence of geometric and hydrodynamic variables as well as several parameters such as multicommutation timing, ligand and surfactant concentration and reagent pH was assessed.Under the selected working conditions, a linear dynamic range from 10 to 500 μg l⁻¹ Al(III), a 3σ detection limit of 0.5 μg l⁻¹ and a coefficient of variation of 0.6% at the 30 μg l⁻¹ level were obtained. The analytical features were compared with those reported in previous flow injection and sequential injection methods. The multisyringe technique was successfully applied to the determination of aluminium in drinking water at low mineralisation levels, validating the results by inductively coupled plasma atomic emission spectrometry.     

Sensitive fluorimetric flow injection analysis for fluoride ion with a novel reagent, 2',7'-dichlorofluorescein di-tert-butyldimethylsilyl ether

A novel reagent, 2′,7′-dichlorofluorescein di-tert-butyldimethylsilyl ether (FCl₂TBS), was synthesized for fluoride ion and used for a sensitive fluorimetric flow injection analysis by detecting the recovery of fluorescence due to cleavage of Si-O bond. Four kinds of fluorescein di-tert-butyldimethylsilyl ether (FTBS) analogues were synthesized and FCl₂TBS was the best. By introducing chlorine to FTBS, stability of the reagent, reactivity and the baseline signals were improved. The FIA system was three lines. The sample solution (aqua medium) was injected in the carrier solution (water) and merged with the reagent solution (2.0 × 10⁻⁵ M FCl₂TBS acetone solution), then mixed with phosphate buffer solution (pH 7.5). The fluorescence intensities were measured at λ_ex 503 nm and λ_em 527 nm. The calibration graph had linear relationship between (1.0-50.0) × 10⁻⁶ M and the determinable limit was 1.0 × 10⁻⁶ M. The relative standard deviation of 12 measurements with 1.0 × 10⁻⁵ M F⁻ solution was 1.0% and the sample throughput was 13 h⁻¹. The developed method was successfully applied to river and tap water samples.     

Highly sensitive and selective fluorescence optosensor to detect and quantify benzo[a]pyrene in water samples

We describe here a method for detecting and quantifying the highly carcinogenic polycyclic aromatic hydrocarbon (PAH) benzo[a]pyrene (BaP) in water, based on a flow-trough optical sensor. The technique is fast (response time of 40 s) and simple and at the same time meets the standards of sensitivity and selectivity required by the European Guidelines on Water for Human Consumption. The optosensor is based on the on-line immobilization of BaP on a non-ionic resin (Amberlite XAD-4) solid support in a continuous-flow system. BaP was analyzed in a 15 mM H₂PO₄⁻/HPO₄²⁻ buffer solution with 25% (v/v) 1,4-dioxane at pH 7. Fluorescence intensity was measured at λ_ex/em=392/406 nm. The experimental conditions (reagent phase, pH, type and concentration of buffer solution and organic solvent) and flow-injection values (flow rate and injection volume) were carefully controlled. Under these conditions the optosensor was sensitive to a linear concentration range of between 3.0 and 250.0 ng l⁻¹ with a detection limit of 3.0 ng l⁻¹ and a standard deviation of 1.5% at 150 ng l⁻¹. The optosensor was applied to the quantification of BaP in drinking and waste water samples (95-105% recovery) in presence of the other 15 EPA PAHs at 1000 ng l⁻¹ concentration level. The influence of other fluorescent polycyclic aromatic hydrocarbons and potential interference from ions usually present in water was also evaluated.     

A novel approach in dispersive liquid-liquid microextraction based on the use of an auxiliary solvent for adjustment of density: UV-VIS spectrophotometric and graphite furnace atomic absorption spectrometric determination of gold based on ion pair formation

This paper presents a novel approach to dispersive liquid-liquid microextraction (DLLME), based on the use of an auxiliary solvent for the adjustment of density. The procedure utilises a solvent system consisting of a dispersive solvent, an extraction solvent and an auxiliary solvent, which allows for the use of solvents having a density lower than that of water as an extraction solvent while preserving simple phase separation by centrifugation. The suggested approach could be an alternative to procedures described in the literature in recent months and which have been devoted to solving the same problem. The efficiency of the suggested approach is demonstrated through the determination of gold based on the formation of the ion pair [Au(CN)₂]⁻ anion with Astra Phloxine (R) reagent and its extraction using the DLLME procedure with subsequent UV-VIS spectrophotometric and graphite furnace atomic absorption spectrometric detection. The optimum conditions were found to be: pH 3; 0.8 mmol L⁻¹ K₄[Fe(CN)₆]; 0.12 mmol L⁻¹ R; dispersive solvent, methanol; extraction solvent, toluene; auxiliary solvent, tetrachloromethane. The calibration plots were linear in the ranges 0.39-4.7 mg L⁻¹ and 0.5-39.4 μg L⁻¹ for UV-VIS and GFAAS detection, respectively; thus enables the application of the developed method in two ranges differing from one from another by three orders of magnitude. The presented approach can be applied to the development of DLLME procedures for the determination of other compounds extractable by organic solvents with a density lower than that of water.     

Sensitive and ultra-fast determination of arsenic(III) by gas-diffusion flow injection analysis with chemiluminescence detection

A novel chemiluminescence gas-diffusion flow injection system for the determination of arsenic(III) in aqueous samples is described. The analytical procedure involves injection of arsenic(III) samples and standards into a 0.3 mol L⁻¹ hydrochloric acid carrier stream which is merged with a reagent stream containing 0.2% (w/v) sodium borohydride and 0.015 mol L⁻¹ sodium hydroxide. Arsine, generated in the combined carrier/reagent donor stream, diffuses across the hydrophobic Teflon membrane of the gas-diffusion cell into an argon acceptor stream and then reacts with ozone in the flow-through chemiluminescence measuring cell of the flow system. Under optimal conditions, the method is characterized by a wide linear calibration range from 0.6 μg L⁻¹ to 25 mg L⁻¹, a detection limit of 0.6 μg L⁻¹ and a sample throughput of 300 samples per hour at 25 mg L⁻¹ and 450 samples per hour at 25 μg L⁻¹.     

A spectrophotometric procedure for DNA assay with a micro-sequential injection lab-on-valve meso-fluidic system

A micro-sequential injection spectrophotometric procedure for DNA assay was developed based on the employment of a lab-on-valve (LOV) meso-fluidic analytical system. A small amount of crystal violet solution (10 μl) was de-colored inside the flow cell of the LOV at the presence of 5 μl λ-DNA/HindIII within a certain pH range, and the absorbance decrease of crystal violet solution at 591 nm was measured via optical fibers and was employed as the basis of quantification. A uni-variant approach was adopted for the optimization of experimental parameters, including buffer pH, concentration and volume of crystal violet solution, reaction time and sample/reagent loading flow rates. A linear calibration graph was obtained within 0.2-6.0 μg ml⁻¹, along with a detection limit of 0.07 μg ml⁻¹. The procedure was applied for the determination of λ-DNA/HindIII in synthetic samples in comparison with a documented procedure.     

One-step extraction and derivatization liquid-phase microextraction for the determination of chlorophenols by gas chromatography–mass spectrometry

A sample pretreatment method for the determination of 18 chlorophenols (CPs) in aqueous samples by derivatization liquid-phase microextraction (LPME) was investigated using gas chromatography–mass spectrometry. Derivatization reagent was spiked into the extraction solvent to combine derivatization and extraction into one step. High sensitivity of 18 CPs derivatives could be achieved after optimization of several parameters such as extraction solvent, percentage of derivatization reagent, extraction time, pH, and ionic strength. The results from the optimal method showed that calibration ranging from 0.5 to 500 μg L⁻¹ could be achieved with the RSDs between 1.75% and 9.39%, and the limits of detection (LOD) are ranging from 0.01 to 0.12 μg L⁻¹ for the CPs. Moreover, the proposed LPME method was compared with solid-phase microextraction (SPME) coupled with on-fiber derivatization technique. The results suggested that using both methods are quite agreeable. Furthermore, the recoveries of LPME evaluated by spiked environmental samples ranged from 87.9% (3,5-DCP) to 114.7% (2,3,5,6-TeCP), and environmental water samples collected from the Pearl River were analyzed with the optimized LPME method, the concentrations of 18 CPs ranged from 0.0237 μg L⁻¹ (3,5-DCP) to 0.3623 μg L⁻¹ (2,3,6-TCP).     

Determination of perfluorocarboxylic acids in water by ion-pair dispersive liquid–liquid microextraction and gas chromatography–tandem mass spectrometry with injection port derivatization

A novel technique for derivatization in a gas chromatograph injection port after a one-step extraction of trace perfluorocarboxylic acids (PFCAs) in water with ion pair formation during dispersive liquid–liquid microextraction (DLLME) was investigated. Tetrabutylammonium hydrogen sulfate (TBAHS) was used as the ion pair reagent. PFCA butyl ester derivatives were formed in the GC injection port and then analyzed using gas chromatography coupled to tandem mass spectrometry with negative chemical ionization. According to our analysis, the operative linear range for PFCA detection from 250 pg mL⁻¹ to 2 μg mL⁻¹ with a relative standard derivation (RSD) below 13%. Detection limits were achieved at the level of 37–51 pg mL⁻¹. This method was successfully applied for the analyzing of PFCAs in river water samples from urban and industrial areas without tedious pretreatment. The concentration range over which PFCAs were detected is from 0.6 ng mL⁻¹ to 604.9 ng mL⁻¹.     

Fluorometric determination of fluoride ion by reagent tablets containing 3-hydroxy-2'-sulfoflavone and zirconium(IV) ethylenediamine tetraacetate

A reagent tablet for determination of fluoride ion has been prepared using ethylenediamine-N,N,N′,N′-tetraacetate complex of zirconium (Zr-EDTA), 3-hydroxy-2′-flavone (FS) and an appropriate pH buffer. Dissolving of the tablet into water exhibits an intense blue fluorescence (λ_max = 460 nm) upon excitation at 377 nm and the fluorescence intensity decreases with the presence of fluoride ion. Hence, a simple fluorescent detection procedure for fluoride ion in aqueous media was successfully constructed with this tablet. The principle of this detection system is the ligand exchange reaction of FS bound to Zr-EDTA with fluoride ion. The present system provides an easy, rapid and selective determination method of fluoride ion ranging from 5 × 10⁻⁶ to 1 × 10⁻³ mol dm⁻³. The measurement of real samples with this tablet showed the similar results as those by the common method with the Alfusone reagent.     

Selective extraction, separation and speciation of iron in different samples using 4-acetyl-5-methyl-1-phenyl-1H-pyrazole-3-carboxylic acid

A method for speciation, preconcentration and separation of Fe(II) and Fe(III) in different matrices was developed using solvent extraction and flame atomic absorption spectrometry. 4-Acetyl-5-methyl-1-phenyl-1H-pyrazole-3-carboxylic acid (AMPC) was used as a new complexing reagent for Fe(III). The Fe(III)-AMPC complex was extracted into methyl isobutyl ketone (MIBK) phase in the pH range 1.0-2.5, and Fe(II) ion remained in aqueous phase at all pH. The chemical composition of the Fe(III)-AMPC complex was determined by the Job's method. The optimum conditions for quantitative recovery of Fe(III) were determined as pH 1.5, shaking time of 2 min, 1.64 × 10⁻⁴ mol L⁻¹ AMPC reagent and 10 mL of MIBK. Furthermore, the influences of diverse metal ions were investigated. The level of Fe(II) was calculated by difference of total iron and Fe(III) concentrations. The detection limit based on the 3σ criterion was found to be 0.24 μg L⁻¹ for Fe(III). The recoveries were higher than 95% and relative standard deviation was less than 2.1% (N = 8). The validation of the procedure was performed by the analysis of two certified standard reference materials. The presented method was applied to the determination of Fe(II) and Fe(III) in tap water, lake water, river water, sea water, fruit juice, cola, and molasses samples with satisfactory results.     

Development of a novel flow injection liquid-liquid microextraction method for the on-line separation and preconcentration for determination of zinc(II) using 5-(8-hydroxy-2-quinolinylmethyl)-2,8-dithia-5-aza-2,6-pyridinophane as a sensitive and selective fluorescent chemosensor

A novel flow injection analysis (FIA) system based on liquid-liquid microextraction and fluorimetric determination was developed for the determination of traces of the Zn²⁺ ion using 5-(8-hydroxy-2-quinolinylmethyl)-2,8-dithia-5-aza-2,6-pyridinophane (L) as a sensitive and selective fluorimetric sensor, with λ_ex = 373 nm and λ_em = 530 nm, and hexanol as the extracting organic solvent. In the designed FIA system, the phase separation takes place via gravitation forces in the absence of any segmenter. The influence of pH and ionic strength of the solution, amount of ligand, nature of counter ion, volume of organic solvent, extraction time and coil length was investigated. Under optimized experimental conditions, the calibration curve found to be liner over a concentration range of 0.025-4.53 μg mL⁻¹ (R² = 0.9951) with a limit of detection of 2.3 ng mL⁻¹. The enrichment factor was 45 and relative standard deviation for 7 replicate determinations was 2.43%. The method is very fast and uses low levels of organic solvents. The proposed method was applied successfully to the determination of zinc(II) in human hair, human serum and two inorganic sludge samples.     

Determination of lithium in pharmaceutical formulations used in the treatment of bipolar disorder by flow injection analysis with spectrophotometric detection

In this work, a flow injection system with spectrophotometric detection was developed for the determination of lithium in pharmaceutical formulations used in the treatment of bipolar disorder. Reaction between Quinizarine (1,4-dihydroxyanthraquinone) and Li(I) ion in alkaline medium containing dimethylsulfoxide (DMSO) was explored for this purpose. The flow system was optimized regarding to its chemical (DMSO, Quinizarine and NaOH concentrations and sample pH) and physical parameters (sample loop volume, carrier flow rate and reactor length) in order to establish better conditions in terms of sensitivity and sampling frequency. The results obtained showed that the concentration of DMSO in the reagent solution presents remarkable influence on the magnitude of analytical signal. Chemical species that could be found in the formulations such as Na(I), K(I), Mg(II), Ca(II), Ti(IV), Cl⁻, CO₃²⁻ e sodium dodecylsulfate were tested as possible interfering ions. Among them, only non-monovalent cations presented noticeable interference on lithium signal. However, they were not found in concentrations high enough to cause interference in the determination of lithium in the samples. Sample preparation was performed by sonicating a slurry prepared by dispersing 100 mg of powdered sample in 15 mL of 0.10 mol L⁻¹ HCl solution. Results obtained by developed methodology were not statistically different from those obtained by flame emission spectrometry. In the optimized conditions the method presented a linear range of 5-40 mg L⁻¹ and a relative standard deviation of 3.6% at 5 mg L⁻¹ Li concentration. Detection and quantification limits were 0.54 and 1.8 mg L⁻¹, respectively. Sampling frequency, calculated as the time interval passed between two consecutive injections, was 60 samples per hour. The methodology was successfully applied in the determination of lithium in three commercial samples.     

A novel, environmentally friendly dispersive liquid-liquid microextraction procedure for the determination of copper

A novel, simple and environmentally friendly procedure for copper determination has been developed. The method is based on the formation of an ion associate of Cu(I) with 1,3,3-trimethyl-2-[5-(1,3,3-trimethyl-1,3-dihydroindol-2-ylidene)-penta-1,3-dienyl]-3H-indolium (DIDC) in the presence of chloride ions as ligand, followed by dispersive liquid-liquid microextraction (DLLME) of the formed ion associate into organic phase and UV-Vis spectrophotometric detection. The following experimental conditions were used: pH 3, 0.24 mol L^− 1 chloride ions, 0.06 mmol L^− 1 DIDC. The effect of the nature of the extraction solvent, auxiliary solvent and disperser solvent used was studied. A mixture of amyl acetate, tetrachloromethane, and methanol in a 1:1:3 v/v/v ratio was selected for the DLLME procedure. The absorbance of the coloured extracts at 640 nm wavelength obeys Beer's law in the range 0.020-0.090 mg L^− 1 of Cu. The limit of detection calculated from a blank test (n = 10) based on 3s is 0.005 mg L^− 1 of Cu. The developed procedure was applied to the analysis of water samples. The suggested DLLME is compared with two procedures previously reported from our laboratory based on (1) conventional liquid-liquid extraction, and (2) sequential injection extraction performed in a dual-valve sequential injection system. The advantages and disadvantages of each method are discussed.     

A fast screening method for the presence of atrazine and other triazines in water using flow injection with chemiluminescent detection

Atrazine is a triazine herbicide which contains two secondary aliphatic amine groups. Previous studies have shown that aliphatic amines react with tris(2,2′-bipyridyl)ruthenium(III) to produce chemiluminescence. This paper describes the application of tris(2,2′-bipyridyl)ruthenium(III) to the detection of atrazine and related triazine herbicides in water by flow injection chemiluminescence analysis. The optimised experimental conditions were determined to be: sample and carrier flow rates of 4.6 mL min⁻¹, sample at pH 9 buffered with 50 mM borax, and reagent concentration of 1 mM tris(2,2′-bipyridyl)ruthenium(III) in 20 mM H₂SO₄ (pH 1). Under these conditions, the logarithm of the chemiluminescence intensity versus concentration was linear in the range of 2.15-2150 μg L⁻¹ for samples in MilliQ water, and the limit of detection of atrazine in water was determined to be 1.3 ± 0.1 μg L⁻¹. Validation of the method was performed using direct injection HPLC. The presence of natural organic matter (NOM) significantly increased the chemiluminescence, masking the signal generated by atrazine. Isolating the target analyte via solid phase extraction (SPE) prior to analysis removed this interference and concentrated the samples, resulting in a greatly improved sensitivity with a detection limit of 14 ± 2 ng L⁻¹.     

Zirconium ion selective electrode based on bis(diphenylphosphino) ferrocene incorporated in a poly(vinyl chloride) matrix

A novel potentiometric zirconium - PVC matrix membrane sensor incorporating bis(diphenylphosphino) ferrocene as an electroactive material and tris(2-ethylhexyl)phosphate as solvent mediator is described. In mixed acetate buffer solution of pH 4.8, the sensor displays a rapid and linear response for zirconium ion over the concentration range 1.0 × 10⁻¹ to 1.0 × 10⁻⁷ mol L⁻¹ with a good slope of 59.7 ± 0.3 mV per decade and detection limit 1.8 × 10⁻⁸ mol L⁻¹. The best performance was obtained with membrane composition 33% PVC, 65% TEHP, 1% NaTPB and 1% ionophore. The proposed electrode revealed excellent selectivity for zirconium ion over a wide variety of alkali, alkaline earth, transition and heavy metal ions and could be used in a pH range of 4.15-7.8. The electrode was applied for at least 1 month without any considerable divergence in the potential responses. The practical utility of the electrode has been demonstrated by its use as an indicator electrode in the potentiometric titration of zirconium ions with sodium fluoride and in determination of zirconium ion in some alloy, tape and waste water samples.     

A quantitative method for determination of Co(II) based on the inner filter effect of reagents on the Raman scattering signals of water

It is known that Raman scattering signals are one of main interference sources leading up to determination errors in spectrofluorometry, and thus the signals can be easily detected with a common spectrofluorometer. In this contribution, we propose a quantitative method based on the inner filter effect (IFE) of reagents on the Raman scattering signals of solvent by taking the complexation of divalent cobalt ion with 4-[(5-chloro-2-pyridyl)azo]-1,3-diaminobenzene (5-Cl-PADAB) as a model system. By adjusting the excitation wavelength of the spectrofluorometer, we could easily detect the Raman scattering signals of water at 424 nm where the maximum absorption of 5-Cl-PADAB reagent is located. In a solution of 5-Cl-PADAB, the Raman scattering signals of water are decreased owing to the IFE of 5-Cl-PADAB. If Co(II), which could form the binary complex of Co(II)/5-Cl-PADAB and consumes the 5-Cl-PADAB reagent, is present in such a case for a given amount of 5-Cl-PADAB solution, recovered Raman scattering signals could be observed and measured with a spectrofluorometer. It was found that the intensity of the enhanced Raman scattering signals is proportional to the Co(II) concentration over the range from 2.0 × 10⁻⁷ mol L⁻¹ to 1.0 × 10⁻⁵ mol L⁻¹, and the detection limit could reach 1.2 × 10⁻⁷ mol L⁻¹. With that, Co(II) in samples could be detected with R.S.D. values lower than 2.6% and recoveries over the range of 97.2-104.7%.     

Potassium permanganate-glyoxal chemiluminescence system for flow injection analysis of cephalosporin antibiotics: cefalexin, cefadroxil, and cefazolin sodium in pharmaceutical preparations

A sensitive flow injection chemiluminescence (FL-CL) method for the determination of cephalosporin antibiotics, was developed. The method was based on that cephalosporin antibiotics could enhance the CL reaction of glyoxal and KMnO₄ in sulfuric acid. Method development included the optimization of reagent concentrations and flow-rate. Under the optimized conditions, three cephalosporin antibiotics: cefalexin, cefadroxil, and cefazolin sodium, were determined. The detection limits of the method are 10 ng ml⁻¹ cefalexin, 2 ng ml⁻¹ cefadroxil, and 2 ng ml⁻¹ cefazolin sodium. The method was successfully applied to the determination of three cephalosporin antibiotics in pharmaceutical preparations.     

Determination of phosphate in natural water employing a monosegmented flow system with simultaneous multiple injection

A monosegmented flow system was employed for the determination of low contents of phosphate in natural water. In this approach, sample and reagents are simultaneously injected to a PTFE reaction coil where the homogenization of the mixture occurs while the monosegment is pumped forwards the photometric detector. The proposed system was evaluated by determining phosphate ion, based on the reaction of association between molybdophosphate and malachite green. It was evaluated individually the best concentration of the reagent solution in relation to blank signal (absorbance of the blank) and the sensitivity of the method. A factorial design was proposed to explain the contribution of each component on the formation of the ion association complex, evaluating the individual contributions as well as the synergistic and antagonistic effects. With the established conditions, phosphorous is determined in the concentration range of 5.0-75 μg P PO₄³⁻ l⁻¹ (r=0.9992), with a detection limit of 0.70 μg P PO₄³⁻ l⁻¹ and a relative standard deviation of 2% (20 μg P PO₄³⁻ l⁻¹, n=8). The proposed method has a sampling frequency of 72 h⁻¹.     

Simultaneous determination of pH, chloride and nickel in electroplating baths using sequential injection analysis

A sequential injection analysis system was developed to quantify pH, chloride and nickel in electrolytic baths, in the ranges 1-5 pH units, and 0.1-1.0 and 0.1-1.6 mol l⁻¹, respectively. To enable pH and chloride determination, potentiometric detection with two ion-selective electrodes in a tubular configuration was used. Nickel concentrations were assessed using colorimetric detection at 660 nm. pH was determined prior to nickel determination and just after sample injection (500 μl) into a 0.025 mol l⁻¹ phosphate buffer carrier stream at pH 6.3 and a 9.10 ml min⁻¹ flow rate. For chloride determination, on-line dialysis through a cellulose membrane was used to enable sample dilution and matrix separation. A 2⁵⁻¹ fractional factorial design based on the carrier solution composition and the levels of the hydrodynamic parameters was used for system optimization. At the optimized settings a sampling rate of 40 samples h⁻¹ was attained, with precision and accuracy statistically indistinguishable from those achieved with conventional procedures.