Simultaneous preconcentration of uranium(VI) and thorium(IV) from aqueous solutions using a chelating calix[4]arene anchored chloromethylated polystyrene solid phase

A new chelating polymeric sorbent is developed using Merrifield chloromethylated resin anchored with calix[4]arene-o-vanillinsemicarbazone for simultaneous separation and solid phase extractive preconcentration of U(VI) and Th(IV). The “upper-rim” functionalized calix[4]arene-o-vanillinsemicarbazone was covalently linked to Merrifield resin and characterized by FT-IR and elemental analysis. The synthesized chelating polymeric sorbent shows superior binding affinity towards U(VI) and Th(IV) under selective pH conditions. Various physico-chemical parameters that influence the quantitative extraction of metal ions were optimized. The optimum pH range and flow rates for U(VI) and Th(IV) were 6.0-7.0 and 1.0-4.0 ml min⁻¹ and 3.5-4.5 and 1.5-4.0 ml min⁻¹, respectively. The total sorption capacity found for U(VI) and Th(IV) was 48734 and 41175 μg g⁻¹, respectively. Interference studies carried out in the presence of diverse ions and electrolyte species showed quantitative analyte recovery (98-98.5%) with lower limits of detection, 6.14 and 4.29 μg l⁻¹ and high preconcentration factors, 143 and 153 for U(VI) and Th(IV), respectively. The uptake and stripping of these metal ions on the resin were fast, indicating a better accessibility of the metal ions towards the chelating sites. The analytical applicability of the synthesized polymeric sorbent was tested with some synthetic mixtures for the separation of U(VI) and Th(IV) from each other and also from La(III), Cu(II) and Pb(II) by varying the pH and sequential acidic elution. The validity of the proposed method was checked by analyzing these metal ions in natural water samples, monazite sand and standard geological materials.     

Extraction chromatographic method for the separation of actinides and lanthanides using EDHBA grafted AXAD-16 polymer

A new extraction chromatographic method has been developed by grafting chloromethylated polymer support with 4-ethoxy-N,N-dihexylbutanamide (EDHBA), for the selective extraction of U(VI), Th(IV), La(III) and Nd(III) from highly acidic matrices. The developed grafted polymer has been characterized using ¹³C-CPMAS NMR spectroscopy, FT-NIR spectroscopy and also by CHN elemental analysis. The water regaining capacity of the grafted polymer is studied by TGA measurements and the active participation of the amide moiety towards metal ion complexation has been confirmed by Far IR spectroscopy. For the quantitative extraction of metal ions to the resin phase, various physio-chemical parameters are optimized by both static and dynamic methods. The developed amide grafted polymeric matrix shows good distribution ratio values even at high acidities, with the maximum metal sorption capacity values being 0.36, 0.69, 0.32 and 0.42 mmol g⁻¹ for U(VI), Th(IV), La(III) and Nd(III), respectively, at 6 M HNO₃ medium. The kinetics of metal ion phase equilibration is found to be moderately fast, with t_1/2 values of <6 min, for all the analytes of interest. The limits of analyte quantification (LOQ) using the developed method are in the range of 15-30 μg L⁻¹. Moreover, the sequential separation of the sorbed actinides and lanthanides could be achieved by first eluting with 100 mL of distilled water (for actinides) followed by elution with 20 mL of 0.1 M EDTA (for lanthanides). The selectivity behavior and the practical applicability of the developed resin are tested using synthetic low level nuclear reprocessing mixtures and also with monazite sand. The analytical data are within 3.8% relative standard deviation, reflecting the reproducibility and reliability of the developed method.     

Synthesis and applications of surface-grafted Th(IV)-imprinted polymers for selective solid-phase extraction of thorium(IV)

A new functional monomer N-(o-carboxyphenyl)maleamic acid (CPMA) was synthesized and chosen for the preparation of surface-grafted ion-imprinted polymers (IIPs) specific for thorium(IV). Polymerizable double bond was introduced to silica gel surface by amidation reaction between -NH₂ and maleic anhydride. In the ion-imprinting process, thorium(IV) was complexed with the carboxyl groups, then was imprinted in the polymers grafted to the silica gel surface. The imprinted Th(IV) was removed with 3 mol L⁻¹ HCl. The obtained imprinted particles exhibited excellent selectivity and rapid kinetics process for Th(IV). The relatively selective factor (α_r) values of Th(IV)/La(III), Th(IV)/Ce(III), Th(IV)/Nd(III), Th(IV)/U(VI), and Th(IV)/Zr(IV) were 85.7, 88.9, 26.6, 64.4, and 433.8, respectively, which were greater than 1. The precision (R.S.D.), the detection limit (3σ), and the quantification limit (10σ) of the method were 1.9%, 0.51 ng mL⁻¹ and 1.19 ng mL⁻¹, respectively. The prepared IIPs as solid-phase extractants were successfully applied for the preconcentration of trace thorium in natural and certified samples prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES) with satisfactory results.     

A column system for the selective extraction of U(VI) and Th(IV) using a new chelating sorbent

A new method has been developed using (bis-3,4-dihydroxy benzyl)p-phenylene diamine functionalized to XAD-16 (a polystyrene divinyl benzene copolymer) matrix, to preconcentrate mainly U(VI) and Th(IV) from synthetic and real samples. The developed method is free from matrix interference due to alkali and alkaline metal ions and preconcentrates the actinides with a high degree of selectivity, with consistent trace recoveries. The new chelating resin provides dramatic improvement in metal exchange rate, with half value saturation time (t_1/2) of less than 1.6 min. The developed method was superior in its metal loading capacity for U(VI) and Th(IV), with values of 0.666 and 0.664 mmol g⁻¹, respectively. Various physio-chemical properties like effect of solution pH, kinetic studies, resin loading capacity, sample breakthrough volume, matrix effects etc., on metal ion sorption to sorbent phase, were studied using both batch and column method. The new chelatogen was applied to extract U(VI) from near neutral real water samples. Preconcentration and separation of metal ions were possible through pH variation and also by varying the eluant concentration. A high preconcentration factor value of 350 with a lower limit of detection of 20 and 30 ng cm⁻³ was obtained for U(VI) and Th(IV), respectively. The practical applicability of the developed resin was examined using synthetic and real samples such as sea/well water samples. The method provides low relative standard deviation values of <3.5% for all analytical measurements, reflecting on the reproducibility and accuracy of the developed method. The new resin is quite durable with recycling time >35 cycles, without any major change in its quantitative metal uptake nature.     

Selective extraction of U(VI) over Th(IV) from acidic streams using di-bis(2-ethylhexyl) malonamide anchored chloromethylated polymeric matrix

A new chelating polymeric sorbent has been developed using Merrifield chloromethylated resin anchored with di-bis (2-ethylhexyl) malonamide (DB2EHM). The modified resin was characterized by CPMAS NMR spectroscopy, FT-NIR-FIR spectroscopy, CHN elemental analysis and also by thermo gravimetric analysis. The fabricated sorbent showed superior binding affinity for U(VI) over Th(IV) and other diverse ions, even under high acidities. Various physio-chemical parameters, like solution acidity, phase exchange kinetics, metal sorption capacity, electrolyte tolerance studies, etc., influencing the resin’s metal extractive behavior were studied by both static and dynamic method. Batch extraction studies performed over a wide range of solution acidity (0.01-10 M) revealed that selective extraction of U(VI) could be achieved even up to 4 M acidity with distribution ratios (D) in the order of ∼10³. The phase exchange kinetics studies performed for U(VI) and Th(IV) revealed that time duration of <15 min was sufficient for >99.5% extraction. But similar studies when preformed for trivalent lanthanides gave very low D values (<50), with the extraction time extending up to 60 min. The metal sorption studies performed for U(VI) and Th(IV) at 5 M HNO₃ was found to be 62.5 and 38.2 mg g⁻¹,respectively. Extraction efficiency in the presence of inferring electrolyte species and inorganic cations were also examined. Metal ion desorption was effective using 10-15 mL of 1 M (NH₄)₂CO₃ or 0.5 M α-hydroxy isobutyric acid (HIBA). Extraction studies performed on a chromatographic column at 5 M acidity were found to give enrichment factor values of 310 and 250 for U(VI) and Th(IV), respectively. The practical utility of the fabricated chelating sorbent and its efficiency to extract actinides from acidic waste streams was tested using a synthetic nuclear spent fuel solution. The R.S.D. values obtained on triplicate measurements (n = 3) were within 5.2%.     

Selective Preconcentration of U(VI) and Th(IV) in Trace and Macroscopic Levels Using Malonamide Grafted Polymer from Acidic Matrices

A novel polymeric sorbent for selective extraction of U(VI) and Th(IV) from highly acidic wastes was prepared by modifying Merrifield chloromethylated resin with N,N,N′,N′-tetrahexylmalonamide. The functionalized resin was characterized by FT-IR spectroscopy, CPMAS NMR spectroscopy, CHN elemental analysis and thermo-gravimetric analysis. Various physiochemical parameters responsible for quantitative extraction of metal ions were studied by static and dynamic methods. The resin exhibited very good extractability over a wide range of acidity (0.01–10 M) with a faster exchange rate (saturation possible within 20 min) and high sorption capacities (0.645 and 0.558 mmol g⁻¹) for U(VI) and Th(IV), respectively. Quantitative metal desorption was achieved by using 0.5 M (NH₄)₂CO₃ for both analytes. The significant feature of the resin is the possibility of sequential separation and the ability to elute only U(VI) with water, thus offering the possibility of sequential separation of U(VI) and Th(IV). Interference studies with commonly encountered metal ions, rare earth ions and electrolytes were conducted. Enrichment factors of 400 and 350 with a limit of quantification of 20 ng mL⁻¹ and 50 ng mL⁻¹ were achieved for the two analytes. All the analytical data were within 3.8% RSD, reflecting the reproducibility and reliability of the method.     

Selective extraction of U(VI), Th(IV), and La(III) from acidic matrix solutions and environmental samples using chemically modified Amberlite XAD-16 resin

A new grafted polymer has been developed by the chemical modification of Amberlite XAD-16 (AXAD-16) polymeric matrix with [(2-dihydroxyarsinoylphenylamino)methyl]phosphonic acid (AXAD-16-AsP). The modified polymer was characterized by a combination of ¹³C CPMAS and ³¹P solid-state NMR, Fourier transform-NIR-FIR-Raman spectroscopy, CHNPS elemental analysis, and thermogravimetric analysis (TGA). The distribution studies for the extraction of U(VI), Th(IV), and La(III) from acidic solutions were performed using an AXAD-16-AsP-packed chromatographic column. The influences of various physiochemical parameters on analyte recovery were optimized by both static and dynamic methods. Accordingly, even under high acidities (>4 M), good distribution ratio (D) values (10²–10⁴) were achieved for all the analytes. Metal ion desorption was effective using 1 mol L^–1 (NH₄)₂CO₃. From kinetic studies, a time duration of <15 min was sufficient for complete metal ion saturation of the resin phase. The maximum metal sorption capacities were found to be 0.25, 0.13, and 1.49 mmol g^–1 for U(VI); 0.47, 0.39, and 1.40 mmol g^–1 for Th(IV); and 1.44, 1.48, and 1.12 mmol g^–1 for La(III), in the presence of 2 mol L^–1 HNO₃, 2 mol L^–1 HCl, and under pH conditions, respectively. The analyte selectivity of the grafted polymer was tested in terms of interfering species tolerance studies. The system showed an enrichment factor of 365, 300, and 270 for U(VI), Th(IV), and La(III), and the limit of analyte detection was in the range of 18–23 ng mL^–1. The practical applicability of the polymer was tested with synthetic nuclear spent fuel and seawater mixtures, natural water, and geological samples. The RSD of the total analytical procedure was within 4.9%, thus confirming the reliability of the developed method.     

Selective enrichment of U(VI), Th(IV) and La(III) from high acidic streams using a new chelating ion-exchange polymeric matrix

An off-line extraction chromatographic technique has been developed using Amberlite XAD-16 (AXAD-16)-N,N-dihexylcarbamoylmethyl phosphonic acid, as the stationary phase for the extraction of uranium, thorium and lanthanum from nuclear spent fuels as well as from geological and natural water resources. The chemical modifications of the polymeric matrix were monitored using FT-IR spectroscopy, CHNPS elemental analysis and also by thermo gravimetric analysis for water regain measurements. Various physio-chemical parameters influencing the quantitative metal ion extraction by the resin phase were optimized by both static and dynamic methods. The developed resin matrix showed good distribution ratio values under wide concentrations of acidity and pH conditions. Moreover, the sequential separation of analytes is also possible at sample pH 6.5. Also, the polymeric matrix showed superior metal sorption capacities and rapid metal exchange kinetics with a high sample flow rate value of 26 cm³ min⁻¹ for all the three analytes. Thus, reducing the time of analyte extraction from large number of samples anticipated in nuclear waste management programs. The quantitative metal ion recovery of >99.8% was effected with 0.5 M (NH₄)₂CO₃ solution. The method was highly sensitive with lower limits of detections to be 10, 20 and 15 ng cm⁻³ for U(VI), Th(IV) and La(III), respectively, with a better pre-concentration values of 333 for U(VI) and Th(IV) and 400 for La(III), respectively paving way for its applicability in pre-concentrating trace analytes from large sample volumes. The analytical data were within 4.2% R.S.D. reflecting the reproducibility and reliability of the developed method.     

Simultaneous spectrophotometric determination of trace amounts of uranium, thorium, and zirconium using the partial least squares method after their preconcentration by α-benzoin oxime modified Amberlite XAD-2000 resin

A new solid phase extraction method for separation and preconcentration of trace amounts of uranium, thorium, and zirconium in water samples is proposed. The procedure is based on the adsorption of U(VI), Th(IV) and Zr(IV) ions on a column of Amberlite XAD-2000 resin loaded with α-benzoin oxime prior to their simultaneous spectrophotometric determination with Arsenazo III using orthogonal signal correction partial least squares method. The enrichment factor for preconcentration of uranium, thorium, and zirconium was found to be 100. The detection limits for U(VI), Th(IV) and Zr(IV) were 0.50, 0.54, and 0.48 μg L⁻¹, respectively. The precision of the method, evaluated as the relative standard deviation obtained by analyzing a series of 10 replicates, was below 4% for all elements. The practical applicability of the developed sorbent was examined using synthetic seawater, natural waters and ceramic samples.     

Preconcentration of uranium(VI) and thorium(IV) from aqueous solutions using low-cost abundantly available sorbent

Olive cake as low-cost abundantly available sorbent has been characterized by N₂ at 77 K adsorption, porosity analysis, elemental analysis and IR spectra and has been used for preconcentrating of uranium(VI) and thorium(IV) ions prior to their determination spectrophotometrically. The optimum pH values for quantitative sorption of U(VI) and Th(IV) are 4–7 and 3–7, respectively. The enrichment factor for the preconcentration of U(VI) and Th(IV) were found to be 125 and 75 in the given order. The sorption capacity of olive cake is in the range of 2,260–15,000 μg g⁻¹ for Th(IV) and in the range of 1,090–17,000 μg g⁻¹ for U(VI) at pH 3–7. The sorbent exhibits good reusability and the uptake and stripping of the studied ions were fairly rapid. The elution of U(VI) and Th(IV) was performed with 0.3–1 M HCl/1–2 M HNO₃ and 0.3–0.8 M HCl/1 M HNO₃, respectively. The precision of the method was 1.8 RSD% for U(VI) and 2.5 RSD% for Th(IV) in a concentration of 1.00 μg mL⁻¹ for 10 replicate analysis. The influence of some electrolytes and cations as interferents was discussed. Separation of U(VI) and Th(IV) from other metal ions in synthetic solution was achieved.     

Solid phase extraction and preconcentration of uranium(VI) and thorium(IV) on Duolite XAD761 prior to their inductively coupled plasma mass spectrometric determination

A simple and effective method is presented for the separation and preconcentration of thorium(IV) and uranium(VI) by solid phase extraction on Duolite XAD761 adsorption resin. Thorium(IV) and uranium(VI) 9-phenyl-3-fluorone chelates are formed and adsorbed onto the Duolite XAD761. Thorium(IV) and uranium(VI) are quantitatively eluted with 2 mol L⁻¹ HCl and determined by inductively coupled plasma-mass spectrometry (ICP-MS). The influences of analytical parameters including pH, amount of reagents, amount of Duolite XAD761 and sample volume, etc. were investigated on the recovery of analyte ions. The interference of a large number of anions and cations has been studied and the optimized conditions developed have been utilized for the trace determination of uranium and thorium. A preconcentration factor of 30 for uranium and thorium was achieved. The relative standard deviation (N = 10) was 2.3% for uranium and 4.5% for thorium ions for 10 replicate determinations in the solution containing 0.5 μg of uranium and thorium. The three sigma detection limits (N = 15) for thorium(IV) and uranium(VI) ions were found to be 4.5 and 6.3 ng L⁻¹, respectively. The developed solid phase extraction method was successively utilized for the determination of traces thorium(IV) and uranium(VI) in environmental samples by ICP-MS.     

Amberlite XAD-4 functionalized with succinic acid for the solid phase extractive preconcentration and separation of uranium(VI)

Amberlite XAD-4 resin has been functionalized with succinic acid by coupling it with dibromosuccinic acid after acetylation. The resulting resin has been characterized by FT-IR, elemental analysis and TGA and has been used for preconcentrative separation of uranium(VI) from host of other inorganic species prior to its determination by spectrophotometry. The optimum pH value for quantitative sorption of uranium(VI) in both batch and column modes is 4.5-8.0 and desorption can be achieved by using 5.0 ml of 1.0 mol l⁻¹ HCl. The sorption capacity of functionalized resin is 12.3 mg g⁻¹. Calibration graphs were rectilinear over the uranium(VI) concentrations in the range 5-200 μg l⁻¹. Five replicate determinations of 50 μg of uranium(VI) present in 1000 ml of solution gave a mean absorbance of 0.10 with a relative standard deviation of 2.56%. The detection limit corresponding to three times the standard deviation of the blank was found to be 2 μg l⁻¹. Various cationic and anionic species at 200-fold amounts do not interfere during the preconcentration of 5.0 μg of uranium(VI) present in 1000 ml (batch) or 100 ml (column) of sample solution. Further, adsorption kinetic and isotherm studies were also carried out by a batch method to understand the nature of sorption of uranium(VI) with the succinic acid functionalized resin. The accuracy of the developed solid phase extractive preconcentration method in conjunction with Arsenazo III procedure was tested by analyzing marine sediment (MESS-3) and soil (IAEA soil-7) reference material. Further, the above procedure has been successfully employed for the analysis of soil and sediment samples.     

Synthesis of chitosan resin possessing 3,4-diamino benzoic acid moiety for the collection/concentration of arsenic and selenium in water samples and their measurement by inductively coupled plasma-mass spectrometry

A chitosan resin functionalized with 3,4-diamino benzoic acid (CCTS-DBA resin) was newly synthesized by using a cross-linked chitosan (CCTS) as base material. The adsorption behavior of trace amounts of elements on the CCTS-DBA resin was examined by the pretreatment with a mini-column and measurement of the elements by inductively coupled plasma-Mass spectrometry (ICP-MS). Arsenic(V) could be retained on the CCTS-DBA resin at pH 3 as an oxoanion of H₂AsO₄⁻. Selenium(VI) is strongly adsorbed at pH 2 and pH 3 as an oxoanion of SeO₄²⁻, while selenium(IV) as HSeO₃⁻ is adsorbed on the resin at pH 3. The sorption capacities are 82, 64, and 88 mg g⁻¹resin for As(V), Se(IV), and Se(VI), respectively. The effect of common anions and cations on the adsorption of As(V), Se(IV), and Se(VI) were studied; there was no interference from such anionic matrices as chloride, sulfate, phosphate, and nitrate up to 20 ppm, as well as from such artificial river water matrices as Na, K, Mg, and Ca after passing samples through the mini-column containing the resin. The CCTS-DBA resin was applied to the collection of arsenic and selenium species in bottled drinking water, tap water, and river water.     

Sulfonylcalix[4]arenetetrasulfonate as pre-column chelating reagent for selective determination of aluminum(III), iron(III), and titanium(IV) by ion-pair reversed-phase high-performance liquid chromatography with spectrophotometric detection

Sulfonylcalix[4]arenetetrasulfonate (SO₂CAS) has been examined as a pre-column chelating reagent for ultratrace determination of metal ions by ion-pair reversed-phase high-performance liquid chromatography with spectrophotometric detection. Metal ions were converted into the SO₂CAS chelates in an acetic buffer solution (pH 4.7). The chelates were injected onto a n-octadecylsilanized silica-type Chromolith™ Performance RP-18e column and were eluted using a methanol (50 wt.%)-water eluent (pH 5.6) containing tetra-n-butylammonium bromide (7.0 mmol kg⁻¹), acetate buffer (5.0 mmol kg⁻¹), and disodium ethylendiamine-N,N,N′,N′-tetraacetate (0.10 mmol kg⁻¹). Under the conditions used, Al(III), Fe(III), and Ti(IV) were selectively detected among 21 kinds of metal ions [Al(III), Ba(II), Be(II), Ca(II), Cd(II), Co(II), Cr(III), Cu(II), Fe(III), Ga(III), Hf(IV), In(III), Mg(II), Mn(II), Mo(VI), Ni(II), Pb(II), Ti(IV), V(V), Zn(II), and Zr(IV)]. The detection limits on a 3σ blank basis were 8.8 nmol dm⁻³ (0.24 ng cm⁻³) for Al(III), 7.6 nmol dm⁻³ (0.42 ng cm⁻³) for Fe(III), and 17 nmol dm⁻³ (0.80 ng cm⁻³) for Ti(IV). The practical applicability of the proposed method was checked using river and tap water samples.     

Chemical enrichment and separation of uranyl ions in aqueous media using novel polyurethane foam chemically grafted with different basic dyestuff sorbents

The new type of the grafted polyurethane foam sorbents were prepared by coupling polyether polyol, toluene diisocyanate and basic dyestuff (Methylene blue, Rhodamine B and Brilliant green). The Me.B-PUF, Rh.B-PUF and Br.G-PUF were characterized using UV/vis, IR and TGA. The adsorption properties and chromatographic behaviour of these new adsorbents for preconcentration and separation of uranium(VI) ions at low concentrations from aqueous thiocyanate media were investigated by a batch process. The maximum sorption of U(VI) was in the pH ranges 1-4. The kinetics of sorption of the U(VI) by the Grafted-PUF were found to be fast with half life of sorption (t_1/2) in 2.43 min. The average sorption capacity of different sorbents 0.124 meq g⁻¹ for uranyl ions, enrichment factors ≈40 and the recovery 98-100% were achieved (R.S.D. ≈ 0.73%). The basic dyestuff Grafted-PUF could be used many times without decreasing their capacities significantly. The value of the Gibbs free energy (ΔG) for the sorbents is −7.3 kJ mol⁻¹, which reflects the spontaneous nature of sorption process. The sorption mechanism of the metal ion onto Grafted-PUF was also discussed.     

Chromium(III, VI) speciation analysis with preconcentration on a maleic acid-functionalized XAD sorbent

Chromium may exist in environmental waters as Cr(III) and Cr(IV), the latter being the toxic and carcinogenic form. Since atomic absorption spectrometry (AAS) and inductively coupled plasma atomic emission spectrometry can only yield information on total Cr concentration, a polymer resin bearing O,O-donor chelating groups such as the maleic acid-functionalized XAD(CO)CHCHCOOH resin was synthesized to selectively retain Cr(III) at pH 4.0-5.5. The dynamic breakthrough capacity of the resin for Cr(III) at pH 5.0 was 7.52 mg g⁻¹, and the preconcentration factor extended to 250-300. Chromium(III) in the presence of 250-fold Cr(VI)—which was not retained—could be effectively preconcentrated on the NH₄⁺-form of the resin and determined by AAS or diphenylcarbazide (DPC) spectrophotometry. When Cr(VI) was reduced to Cr(III) with Na₂SO₃ solution brought to pH 1 by the addition of 1 M H₂SO₄, and preconcentrated on the resin, total Cr could be determined. The developed method was validated with a blended coal sample CRM-1632. Since the adsorption behavior as a function of pH of possible interferent metal ions, e.g. Ni(II), Co(II), Cu(II), Cd(II), Zn(II), Pb(II) and Fe(III), was similar to that of Cr(III), selective elution of Cr(III) from the resin was realized using a mixture of 1 wt.% H₂O₂+1 M NH₃. The eluate containing Cr as chromate could be directly analyzed by diphenyl carbazide spectrophotometry without any adverse effect from the common interferents of this method, i.e. Fe(III), Cu(II) Hg(II), VO₃⁻, MoO₄²⁻ and WO₄²⁻. Various synthetic waste solutions typical of electroplating bath effluents containing Cr, Cu, Ni, Zn, Na, Ca, cyanide (and chemical oxidation demand (COD), achieved by glucose addition) were subjected to pretreatment procedures such as hypochlorite oxidation (of cyanide) and catalytic oxidation (of COD) with peroxodisulfate. Chromium determination gave satisfactory results. The combined column preconcentration—selective elution—diphenylcarbazide spectrophotometric determination was also successfully applied to the determination of Cr in artificial and real seawater.     

Simultaneous extraction and preconcentration of uranium and thorium in aqueous samples by new modified mesoporous silica prior to inductively coupled plasma optical emission spectrometry determination

A new synthesized modified mesoporous silica (MCM-41) using 5-nitro-2-furaldehyde (fural) was applied as an effective sorbent for the solid phase extraction of uranium(VI) and thorium(IV) ions from aqueous solution for the measurement by inductively coupled plasma optical emission spectrometry (ICP OES). The influences of some analytical parameters on the quantitative recoveries of the analyte ions were investigated in batch method. Under optimal conditions, the analyte ions were sorbed by the sorbent at pH 5.5 and then eluted with 1.0 mL of 1.0 mol L⁻¹ HNO₃. The preconcentration factor was 100 for a 100 mL sample volume. The limits of detection (LOD) obtained for uranium(VI) and thorium(IV) were 0.3 μg L⁻¹. The maximum sorption capacity of the modified MCM-41 was found to be 47 and 49 mg g⁻¹ for uranium(VI) and thorium(IV), respectively. The sorbent exhibited good stability, reusability, high adsorption capacity and fast rate of equilibrium for sorption/desorption of uranium and thorium ions. The applicability of the synthesized sorbent was examined using CRM and real water samples.     

Differential pulse voltammetric determination of trace Te(IV) at a poly(3,3′-diaminobenzidine) film modified gold electrode in flow systems

Electropolymerization of 3,3′-diaminobenzidine on a gold surface gave an adherent, stable film of poly(3,3′-diaminobenzidine) (PDAB). This polymer film retained the complexational functionalities of its monomer, demonstrating preconcentration abilities for several ions, including Se(IV) and Te(IV). In particular, in this work, continuous flow and flow injection methods were developed for the sensitive and selective determination of Te(IV). The optimized method for the continuous flow mode had a detection limit of 5.6×10⁻⁹ mol l⁻¹ for 10 min preconcentration. Typical relative standard deviations for six consecutive determinations were 1.82 and 2.56% for Te(IV) concentrations of 1.0×10⁻⁶ and 5.0×10⁻⁸ mol l⁻¹, respectively (10 min preconcentration). The method was applied to the determination of Te(IV) in real samples.     

Highly selective preconcentration of Cu(II) from seawater and water samples using amidoamidoxime silica

Chemically modified silica containing amidoamidoxime group was studied as a sorbent for solid-phase extraction (SPE) and preconcentration of Cu(II) prior to determination by flame atomic absorption spectrometry (FAAS). The sorbent showed an extremely high selectivity towards Cu(II) in the pH range of 4-6, while the extraction of Pb(II), Cd(II), Ni(II) and Co(II) was low. The adsorption isotherm followed the Langmuir model and the maximum sorption capacity of 0.0163 mmol Cu(II) g⁻¹ was achieved. In the flow system, Cu(II) was completely retained on a column containing 40 mg of the modified silica at the flow rate of 4.0 mL min⁻¹ and quantitatively eluted by 5 mL of 1% (v/v) HNO₃. No interference from Na⁺, K⁺, Mg²⁺, Ca²⁺, Cl⁻ and SO₄²⁻ at 10, 100 and 1000 mg L⁻¹ was observed. When applied for preconcentration and determination of Cu(II) in tap water, pond water, and seawater, the recoveries were 96, 101, and 95%, respectively, with high precision (% relative standard deviation (R.S.D.) < 4) and low method detection limit (9 μg L⁻¹).     

Speciation of vanadium in water with quinine modified resin micro-column separation/preconcentration and their determination by fluorination assisted electrothermal vaporization (FETV)-inductively coupled plasma optical emission spectrometry (ICP-OES)

A simple and selective method of flow injection (FI) using a micro-column packed with quinine modified resin as solid phase extractant has been developed for preconcentration and separation of trace amount of vanadium(V) and vanadium(IV) in water samples, followed by determination with fluorination assisted electrothermal vaporization (FETV)-inductively coupled plasma optical emission spectrometry (ICP-OES). At pH 3 ∼ 3.8, the modified resin is selective towards V(V) and almost not towards V(IV), while, V(IV) could be quantitatively adsorbed by the modified resin at pH 5 ∼ 7. The two vanadium species adsorbed by modified resin could be readily desorbed quantitatively with 0.3 ml of 0.5 mol l⁻¹ HCl. Both vanadium species in elution were then determined by ETV-ICP-OES with the use of polytetrafluoroethylene (PTFE) as chemical modifier. Effects of acidity, sample flow rate, concentration of elution solution and interfering ions on the recovery of the analytes have been systematically investigated. Under the optimal conditions, the adsorption capacities of the quinine modified resin for V(V) and V(IV) are 7.6 and 8.0 mg g⁻¹, respectively. The detection limit (3σ) of V is 0.072 ng ml⁻¹ for FETV-ICP-OES and 0.56 pg ml⁻¹ for FETV-ICP-MS with enrichment factor of 62.5, and the relative standard deviation (R.S.D.) is 4.9% (n = 9, C = 0.2 μg ml⁻¹) and 3.8% (n = 9, C = 1.0 ng ml⁻¹), respectively. The proposed method has been applied to the determination of trace V(V) and V(IV) in different water samples, and the recoveries of V(V) and V(IV) are 100 ± 10%. In order to further verify the accuracy of the developed method, FETV-ICP-MS was employed to analyze the vanadium species in water samples after separation/preconcentration, and analytical results are in good agreement with that obtained by the proposed method. The developed method was also applied to the analysis of the total V in GBW07401 soil certified reference material and in GBW07605 tea leaves certified reference material, and the determined values coincided with the certified values very well.